- 02 Apr, 2012 11 commits
-
-
Shengzhou Liu authored
commit 28c56ea1 upstream. If USB UTMI PHY is not enable, writing to portsc register will lead to kernel hang during boot up. Signed-off-by:
Shengzhou Liu <Shengzhou.Liu@freescale.com> Reported-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Michał Wróbel authored
commit 57e596f3 upstream. Signed-off-by:
Michał Wróbel <michal.wrobel@flytronic.pl> Signed-off-by:
-
Jim Paris authored
commit dc0827c1 upstream. Add PID 0x6015, corresponding to the new series of FT-X chips (FT220XD, FT201X, FT220X, FT221X, FT230X, FT231X, FT240X). They all appear as serial devices, and seem indistinguishable except for the default product string stored in their EEPROM. The baudrate generation matches FT232RL devices. Tested with a FT201X and FT230X at various baudrates (100 - 3000000). Sample dmesg: ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver usb 2-1: new full-speed USB device number 6 using ohci_hcd usb 2-1: New USB device found, idVendor=0403, idProduct=6015 usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-1: Product: FT230X USB Half UART usb 2-1: Manufacturer: FTDI usb 2-1: SerialNumber: DC001WI6 ftdi_sio 2-1:1.0: FTDI USB Serial Device converter detected drivers/usb/serial/ftdi_sio.c: ftdi_sio_port_probe drivers/usb/serial/ftdi_sio.c: ftdi_determine_type: bcdDevice = 0x1000, bNumInterfaces = 1 usb 2-1: Detected FT-X usb 2-1: Number of endpoints 2 usb 2-1: Endpoint 1 MaxPacketSize 64 usb 2-1: Endpoint 2 MaxPacketSize 64 usb 2-1: Setting MaxPacketSize 64 drivers/usb/serial/ftdi_sio.c: read_latency_timer drivers/usb/serial/ftdi_sio.c: write_latency_timer: setting latency timer = 1 drivers/usb/serial/ftdi_sio.c: create_sysfs_attrs drivers/usb/serial/ftdi_sio.c: sysfs attributes for FT-X usb 2-1: FTDI USB Serial Device converter now attached to ttyUSB0 Signed-off-by:
Jim Paris <jim@jtan.com> Signed-off-by:
-
Michał Wróbel authored
commit 47594d55 upstream. Signed-off-by:
-
Bruno Thomsen authored
commit c1cee1d8 upstream. Microchip VID (0x04d8) was mislabeled as Hornby VID according to USB-IDs. A Full Speed USB Demo Board PID (0x000a) was mislabeled as Hornby Elite (an Digital Command Controller Console for model railways). Most likely the Hornby based their design on PIC18F87J50 Full Speed USB Demo Board. Signed-off-by:
Bruno Thomsen <bruno.thomsen@gmail.com> Signed-off-by:
-
Peter Korsgaard authored
commit 444aa7fa upstream. BeagleBone changed to the default FTDI 0403:6010 id in rev A5 to make life easier for Windows users, so we need a similar workaround as the Calao board to support it. Signed-off-by:
Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by:
-
Greg Kroah-Hartman authored
commit 656d2b39 upstream. On some misconfigured ftdi_sio devices, if the manufacturer string is NULL, the kernel will oops when the device is plugged in. This patch fixes the problem. Reported-by:
Wojciech M Zabolotny <W.Zabolotny@elka.pw.edu.pl> Tested-by:
-
Bjørn Mork authored
commit 5889d3d4 upstream. This device presents a total of 5 interfaces with ff/ff/ff class/subclass/protocol. The last one of these is verified to be a QMI/wwan combined interface which should be handled by the qmi_wwan driver, so we blacklist it here. Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Bjørn Mork authored
commit 963940cf upstream. commit 0d905fd5 "USB: option: convert Huawei K3765, K4505, K4605 reservered interface to blacklist" accidentally ANDed two blacklist tests by leaving out a return. This was not noticed because the two consecutive bracketless if statements made it syntactically correct. Signed-off-by:
-
Daniele Palmas authored
commit 7204cf58 upstream. Adding PID for Telit CC864-SINGLE, CC864-DUAL and DE910-DUAL modems Signed-off-by:
Daniele Palmas <dnlplm@gmail.com> Signed-off-by:
-
Meng Zhang authored
commit 0d8520a1 upstream. Add MEDIATEK products to Option driver Signed-off-by:
Meng Zhang <meng.zhang@mediatek.com> Signed-off-by:
Matthias Urlichs <matthias@urlichs.de> Signed-off-by:
-
- 23 Mar, 2012 9 commits
-
-
Greg Kroah-Hartman authored
-
Benjamin Herrenschmidt authored
commit 78c5c68a upstream. The code for "powersurge" SMP would kick in and cause a crash at boot due to the lack of a NULL test. Signed-off-by:
Jeremy Kerr <jeremy.kerr@canonical.com> Reported-by:
Adam Conrad <adconrad@ubuntu.com> Tested-by:
-
Stanislaw Gruszka authored
commit 210787e8 upstream. On il3945_down procedure we free tx queue data and nullify il->txq pointer. After that we drop mutex and then cancel delayed works. There is possibility, that after drooping mutex and before the cancel, some delayed work will start and crash while trying to send commands to the device. For example, here is reported crash in il3945_bg_reg_txpower_periodic(): https://bugzilla.kernel.org/show_bug.cgi?id=42766#c10 Patch fix problem by adding il->txq check on works that send commands, hence utilize tx queue. Reported-by:
Clemens Eisserer <linuxhippy@gmail.com> Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
RongQing.Li authored
[ Upstream commit c5779237 ] ip6_mc_find_dev_rcu() is called with rcu_read_lock(), so don't need to dev_hold(). With dev_hold(), not corresponding dev_put(), will lead to leak. [ bug introduced in 96b52e61 (ipv6: mcast: RCU conversions) ] Signed-off-by:
RongQing.Li <roy.qing.li@gmail.com> Acked-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit dfd25fff ] commit ea4fc0d6 (ipv4: Don't use rt->rt_{src,dst} in ip_queue_xmit()) added a serious regression on synflood handling. Simon Kirby discovered a successful connection was delayed by 20 seconds before being responsive. In my tests, I discovered that xmit frames were lost, and needed ~4 retransmits and a socket dst rebuild before being really sent. In case of syncookie initiated connection, we use a different path to initialize the socket dst, and inet->cork.fl.u.ip4 is left cleared. As ip_queue_xmit() now depends on inet flow being setup, fix this by copying the temp flowi4 we use in cookie_v4_check(). Reported-by:
Simon Kirby <sim@netnation.com> Bisected-by:
-
Anton Blanchard authored
commit b832796c upstream. I have a workload where perf top scribbles over the stack and we SEGV. What makes it interesting is that an snprintf is causing this. The workload is a c++ gem that has method names over 3000 characters long, but snprintf is designed to avoid overrunning buffers. So what went wrong? The problem is we assume snprintf returns the number of characters written: ret += repsep_snprintf(bf + ret, size - ret, "[%c] ", self->level); ... ret += repsep_snprintf(bf + ret, size - ret, "%s", self->ms.sym->name); Unfortunately this is not how snprintf works. snprintf returns the number of characters that would have been written if there was enough space. In the above case, if the first snprintf returns a value larger than size, we pass a negative size into the second snprintf and happily scribble over the stack. If you have 3000 character c++ methods thats a lot of stack to trample. This patch fixes repsep_snprintf by clamping the value at size - 1 which is the maximum snprintf can write before adding the NULL terminator. I get the sinking feeling that there are a lot of other uses of snprintf that have this same bug, we should audit them all. Cc: David Ahern <dsahern@gmail.com> Cc: Eric B Munson <emunson@mgebm.net> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Yanmin Zhang <yanmin_zhang@linux.intel.com> Link: http://lkml.kernel.org/r/20120307114249.44275ca3@krytenSigned-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Anton Blanchard authored
commit c0173863 upstream. When writing files to afs I sometimes hit a BUG: kernel BUG at fs/afs/rxrpc.c:179! With a backtrace of: afs_free_call afs_make_call afs_fs_store_data afs_vnode_store_data afs_write_back_from_locked_page afs_writepages_region afs_writepages The cause is: ASSERT(skb_queue_empty(&call->rx_queue)); Looking at a tcpdump of the session the abort happens because we are exceeding our disk quota: rx abort fs reply store-data error diskquota exceeded (32) So the abort error is valid. We hit the BUG because we haven't freed all the resources for the call. By freeing any skbs in call->rx_queue before calling afs_free_call we avoid hitting leaking memory and avoid hitting the BUG. Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Anton Blanchard authored
commit 2c724fb9 upstream. A read of a large file on an afs mount failed: # cat junk.file > /dev/null cat: junk.file: Bad message Looking at the trace, call->offset wrapped since it is only an unsigned short. In afs_extract_data: _enter("{%u},{%zu},%d,,%zu", call->offset, len, last, count); ... if (call->offset < count) { if (last) { _leave(" = -EBADMSG [%d < %zu]", call->offset, count); return -EBADMSG; } Which matches the trace: [cat ] ==> afs_extract_data({65132},{524},1,,65536) [cat ] <== afs_extract_data() = -EBADMSG [0 < 65536] call->offset went from 65132 to 0. Fix this by making call->offset an unsigned int. Signed-off-by:
-
Ryusuke Konishi authored
commit d7178c79 upstream. According to the report from Slicky Devil, nilfs caused kernel oops at nilfs_load_super_block function during mount after he shrank the partition without resizing the filesystem: BUG: unable to handle kernel NULL pointer dereference at 00000048 IP: [<d0d7a08e>] nilfs_load_super_block+0x17e/0x280 [nilfs2] *pde = 00000000 Oops: 0000 [#1] PREEMPT SMP ... Call Trace: [<d0d7a87b>] init_nilfs+0x4b/0x2e0 [nilfs2] [<d0d6f707>] nilfs_mount+0x447/0x5b0 [nilfs2] [<c0226636>] mount_fs+0x36/0x180 [<c023d961>] vfs_kern_mount+0x51/0xa0 [<c023ddae>] do_kern_mount+0x3e/0xe0 [<c023f189>] do_mount+0x169/0x700 [<c023fa9b>] sys_mount+0x6b/0xa0 [<c04abd1f>] sysenter_do_call+0x12/0x28 Code: 53 18 8b 43 20 89 4b 18 8b 4b 24 89 53 1c 89 43 24 89 4b 20 8b 43 20 c7 43 2c 00 00 00 00 23 75 e8 8b 50 68 89 53 28 8b 54 b3 20 <8b> 72 48 8b 7a 4c 8b 55 08 89 b3 84 00 00 00 89 bb 88 00 00 00 EIP: [<d0d7a08e>] nilfs_load_super_block+0x17e/0x280 [nilfs2] SS:ESP 0068:ca9bbdcc CR2: 0000000000000048 This turned out due to a defect in an error path which runs if the calculated location of the secondary super block was invalid. This patch fixes it and eliminates the reported oops. Reported-by:
Slicky Devil <slicky.dvl@gmail.com> Signed-off-by:
Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Tested-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
- 19 Mar, 2012 20 commits
-
-
Greg Kroah-Hartman authored
-
Ville Syrjala authored
commit 8ee161ce upstream. When the system is under heavy load, there can be a significant delay between the getscl() and time_after() calls inside sclhi(). That delay may cause the time_after() check to trigger after SCL has gone high, causing sclhi() to return -ETIMEDOUT. To fix the problem, double check that SCL is still low after the timeout has been reached, before deciding to return -ETIMEDOUT. Signed-off-by:
Ville Syrjala <syrjala@sci.fi> Signed-off-by:
Jean Delvare <khali@linux-fr.org> Signed-off-by:
-
Guenter Roeck authored
commit 32260d94 upstream. The driver probe function leaked memory if creating the cpu0_vid attribute file failed. Fix by converting the driver to use devm_kzalloc. Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Acked-by:
-
Guenter Roeck authored
commit 33fa9b62 upstream. NCT6775F and NCT6776F have their own set of registers for FAN_STOP_TIME. The correct registers were used to read FAN_STOP_TIME, but writes used the wrong registers. Fix it. Signed-off-by:
-
Jiri Slaby authored
For 3.0 stable kernel the backport of 048cd4e5 "compat: fix compile breakage on s390" breaks compilation... Re-add a single #include <asm/compat.h> in order to fix this. This patch is _not_ necessary for upstream, only for stable kernels which include the "build fix" mentioned above. One fix for arch/s390/kernel/setup.c was already sent and applied. But we need a similar patch for drivers/s390/char/fs3270.c. Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Signed-off-by:
-
David S. Miller authored
commit e0adb990 upstream. Newer version of binutils are more strict about specifying the correct options to enable certain classes of instructions. The sparc32 build is done for v7 in order to support sun4c systems which lack hardware integer multiply and divide instructions. So we have to pass -Av8 when building the assembler routines that use these instructions and get patched into the kernel when we find out that we have a v8 capable cpu. Reported-by:
Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by:
-
Ben Hutchings authored
commit ff3bc1e7 upstream. When pre-allocating skbs for received packets, we set ip_summed = CHECKSUM_UNNCESSARY. We used to change it back to CHECKSUM_NONE when the received packet had an incorrect checksum or unhandled protocol. Commit bc8acf2c ('drivers/net: avoid some skb->ip_summed initializations') mistakenly replaced the latter assignment with a DEBUG-only assertion that ip_summed == CHECKSUM_NONE. This assertion is always false, but it seems no-one has exercised this code path in a DEBUG build. Fix this by moving our assignment of CHECKSUM_UNNECESSARY into efx_rx_packet_gro(). Signed-off-by:
Ben Hutchings <bhutchings@solarflare.com> Signed-off-by:
-
Alan Stern authored
commit 62d3c543 upstream. This patch (as1519) fixes a bug in the block layer's disk-events polling. The polling is done by a work routine queued on the system_nrt_wq workqueue. Since that workqueue isn't freezable, the polling continues even in the middle of a system sleep transition. Obviously, polling a suspended drive for media changes and such isn't a good thing to do; in the case of USB mass-storage devices it can lead to real problems requiring device resets and even re-enumeration. The patch fixes things by creating a new system-wide, non-reentrant, freezable workqueue and using it for disk-events polling. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Acked-by:
Tejun Heo <tj@kernel.org> Acked-by:
Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Stanislaw Gruszka authored
commit 9f53d2fe upstream. The following situation might occur: __blkdev_get: add_disk: register_disk() get_gendisk() disk_block_events() disk->ev == NULL disk_add_events() __disk_unblock_events() disk->ev != NULL --ev->block Then we unblock events, when they are suppose to be blocked. This can trigger events related block/genhd.c warnings, but also can crash in sd_check_events() or other places. I'm able to reproduce crashes with the following scripts (with connected usb dongle as sdb disk). <snip> DEV=/dev/sdb ENABLE=/sys/bus/usb/devices/1-2/bConfigurationValue function stop_me() { for i in `jobs -p` ; do kill $i 2> /dev/null ; done exit } trap stop_me SIGHUP SIGINT SIGTERM for ((i = 0; i < 10; i++)) ; do while true; do fdisk -l $DEV 2>&1 > /dev/null ; done & done while true ; do echo 1 > $ENABLE sleep 1 echo 0 > $ENABLE done </snip> I use the script to verify patch fixing oops in sd_revalidate_disk http://marc.info/?l=linux-scsi&m=132935572512352&w=2 Without Jun'ichi Nomura patch titled "Fix NULL pointer dereference in sd_revalidate_disk" or this one, script easily crash kernel within a few seconds. With both patches applied I do not observe crash. Unfortunately after some time (dozen of minutes), script will hung in: [ 1563.906432] [<c08354f5>] schedule_timeout_uninterruptible+0x15/0x20 [ 1563.906437] [<c04532d5>] msleep+0x15/0x20 [ 1563.906443] [<c05d60b2>] blk_drain_queue+0x32/0xd0 [ 1563.906447] [<c05d6e00>] blk_cleanup_queue+0xd0/0x170 [ 1563.906454] [<c06d278f>] scsi_free_queue+0x3f/0x60 [ 1563.906459] [<c06d7e6e>] __scsi_remove_device+0x6e/0xb0 [ 1563.906463] [<c06d4aff>] scsi_forget_host+0x4f/0x60 [ 1563.906468] [<c06cd84a>] scsi_remove_host+0x5a/0xf0 [ 1563.906482] [<f7f030fb>] quiesce_and_remove_host+0x5b/0xa0 [usb_storage] [ 1563.906490] [<f7f03203>] usb_stor_disconnect+0x13/0x20 [usb_storage] Anyway I think this patch is some step forward. As drawback, I do not teardown on sysfs file create error, because I do not know how to nullify disk->ev (since it can be used). However add_disk error handling practically does not exist too, and things will work without this sysfs file, except events will not be exported to user space. Signed-off-by:
-
Dan Carpenter authored
commit ea5f4db8 upstream. "mem" is type u8. We need parenthesis here or it screws up the pointer math probably leading to an oops. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Jeff Garzik <jgarzik@redhat.com> Signed-off-by:
-
Jun'ichi Nomura authored
commit fe316bf2 upstream. Since 2.6.39 (1196f8b8), when a driver returns -ENOMEDIUM for open(), __blkdev_get() calls rescan_partitions() to remove in-kernel partition structures and raise KOBJ_CHANGE uevent. However it ends up calling driver's revalidate_disk without open and could cause oops. In the case of SCSI: process A process B ---------------------------------------------- sys_open __blkdev_get sd_open returns -ENOMEDIUM scsi_remove_device <scsi_device torn down> rescan_partitions sd_revalidate_disk <oops> Oopses are reported here: http://marc.info/?l=linux-scsi&m=132388619710052 This patch separates the partition invalidation from rescan_partitions() and use it for -ENOMEDIUM case. Reported-by:
Huajun Li <huajun.li.lee@gmail.com> Signed-off-by:
Jun'ichi Nomura <j-nomura@ce.jp.nec.com> Acked-by:
-
Axel Lin authored
commit f03570cf upstream. Don't assign the voltage to selector. Signed-off-by:
Axel Lin <axel.lin@gmail.com> Signed-off-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by:
-
Heiko Carstens authored
For kernels <= 3.0 the backport of 048cd4e5 "compat: fix compile breakage on s390" will break compilation... Re-add a single #include <asm/compat.h> in order to fix this. This patch is _not_ necessary for upstream, only for stable kernels which include the "build fix" mentioned above. Reported-by:
Heiko Carstens <heiko.carstens@de.ibm.com>
-
Joerg Neikes authored
commit 4e503919 upstream. This patch adds support for the Sitecom LN-031 USB adapter with a AX88178 chip. Added USB id to find correct driver for AX88178 1000 Ethernet adapter. Signed-off-by:
Joerg Neikes <j.neikes@midlandgate.de> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 11aad99a ] This driver attempts to use two TX rings but lacks proper support : 1) IRQ handler only takes care of TX completion on first TX ring 2) the stop/start logic uses the legacy functions (for non multiqueue drivers) This means all packets witk skb mark set to 1 are sent through high queue but are never cleaned and queue eventualy fills and block the device, triggering the infamous "NETDEV WATCHDOG" message. Lets use a single TX ring to fix the problem, this driver is not a real multiqueue one yet. Minimal fix for stable kernels. Reported-by:
Thomas Meyer <thomas@m3y3r.de> Tested-by:
-
Li Wei authored
[ Upstream commit d6ddef9e ] When forwarding was set and a new net device is register, we need add this device to the all-router mcast group. Signed-off-by:
Li Wei <lw@cn.fujitsu.com> Signed-off-by:
-
Neal Cardwell authored
[ Upstream commit 4648dc97 ] This commit fixes tcp_shift_skb_data() so that it does not shift SACKed data below snd_una. This fixes an issue whose symptoms exactly match reports showing tp->sacked_out going negative since 3.3.0-rc4 (see "WARNING: at net/ipv4/tcp_input.c:3418" thread on netdev). Since 2008 (832d11c5) tcp_shift_skb_data() had been shifting SACKed ranges that were below snd_una. It checked that the *end* of the skb it was about to shift from was above snd_una, but did not check that the end of the actual shifted range was above snd_una; this commit adds that check. Shifting SACKed ranges below snd_una is problematic because for such ranges tcp_sacktag_one() short-circuits: it does not declare anything as SACKed and does not increase sacked_out. Before the fixes in commits cc9a672e and daef52ba, shifting SACKed ranges below snd_una happened to work because tcp_shifted_skb() was always (incorrectly) passing in to tcp_sacktag_one() an skb whose end_seq tcp_shift_skb_data() had already guaranteed was beyond snd_una. Hence tcp_sacktag_one() never short-circuited and always increased tp->sacked_out in this case. After those two fixes, my testing has verified that shifting SACKed ranges below snd_una could cause tp->sacked_out to go negative with the following sequence of events: (1) tcp_shift_skb_data() sees an skb whose end_seq is beyond snd_una, then shifts a prefix of that skb that is below snd_una (2) tcp_shifted_skb() increments the packet count of the already-SACKed prev sk_buff (3) tcp_sacktag_one() sees the end of the new SACKed range is below snd_una, so it short-circuits and doesn't increase tp->sacked_out (5) tcp_clean_rtx_queue() sees the SACKed skb has been ACKed, decrements tp->sacked_out by this "inflated" pcount that was missing a matching increase in tp->sacked_out, and hence tp->sacked_out underflows to a u32 like 0xFFFFFFFF, which casted to s32 is negative. (6) this leads to the warnings seen in the recent "WARNING: at net/ipv4/tcp_input.c:3418" thread on the netdev list; e.g.: tcp_input.c:3418 WARN_ON((int)tp->sacked_out < 0); More generally, I think this bug can be tickled in some cases where two or more ACKs from the receiver are lost and then a DSACK arrives that is immediately above an existing SACKed skb in the write queue. This fix changes tcp_shift_skb_data() to abort this sequence at step (1) in the scenario above by noticing that the bytes are below snd_una and not shifting them. Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
-
Ulrich Weber authored
[ Upstream commit d1d81d4c ] otherwise source IPv6 address of ICMPV6_MGM_QUERY packet might be random junk if IPv6 is disabled on interface or link-local address is not yet ready (DAD). Signed-off-by:
Ulrich Weber <ulrich.weber@sophos.com> Signed-off-by:
-
Neal Cardwell authored
[ Upstream commit c0638c24 ] In tcp_mark_head_lost() we should not attempt to fragment a SACKed skb to mark the first portion as lost. This is for two primary reasons: (1) tcp_shifted_skb() coalesces adjacent regions of SACKed skbs. When doing this, it preserves the sum of their packet counts in order to reflect the real-world dynamics on the wire. But given that skbs can have remainders that do not align to MSS boundaries, this packet count preservation means that for SACKed skbs there is not necessarily a direct linear relationship between tcp_skb_pcount(skb) and skb->len. Thus tcp_mark_head_lost()'s previous attempts to fragment off and mark as lost a prefix of length (packets - oldcnt)*mss from SACKed skbs were leading to occasional failures of the WARN_ON(len > skb->len) in tcp_fragment() (which used to be a BUG_ON(); see the recent "crash in tcp_fragment" thread on netdev). (2) there is no real point in fragmenting off part of a SACKed skb and calling tcp_skb_mark_lost() on it, since tcp_skb_mark_lost() is a NOP for SACKed skbs. Signed-off-by:
Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Acked-by:
Yuchung Cheng <ycheng@google.com> Acked-by:
Nandita Dukkipati <nanditad@google.com> Signed-off-by:
-
Shreyas Bhatewara authored
[ Upstream commit efead871 ] Fix transport header size Fix the transpoert header size for UDP packets. Signed-off-by:
Shreyas N Bhatewara <sbhatewara@vmware.com> Signed-off-by:
-
