- 13 Apr, 2021 34 commits
-
-
Ong Boon Leong authored
Prepare stmmac_xdp_run_prog() for AF_XDP zero-copy support which will be added by upcoming patches by splitting out the XDP verdict processing into __stmmac_xdp_run_prog() and it callable for XDP ZC path which does not need to verify bpf_prog is not NULL. The stmmac_xdp_run_prog() is used for regular XDP Rx path which requires bpf_prog to be verified. Signed-off-by:
Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ong Boon Leong authored
Below functions are made to be per-queue in preparation of XDP ZC: __init_dma_rx_desc_rings(struct stmmac_priv *priv, u32 queue, gfp_t flags) __init_dma_tx_desc_rings(struct stmmac_priv *priv, u32 queue) The original functions below are stay maintained for all queue usage: init_dma_rx_desc_rings(struct net_device *dev, gfp_t flags) init_dma_tx_desc_rings(struct net_device *dev) Signed-off-by:
-
Ong Boon Leong authored
The per-queue RX buffer allocation in stmmac_reinit_rx_buffers() can be made to use stmmac_alloc_rx_buffers() by merging the page_pool alloc checks for "buf->page" and "buf->sec_page" in stmmac_init_rx_buffers(). This is in preparation for XSK pool allocation later. Signed-off-by:
-
Ong Boon Leong authored
Rearrange RX buffer page_pool recycling logics into dma_recycle_rx_skbufs, so that we prepare stmmac_reinit_rx_buffers() for XSK pool expansion. Signed-off-by:
-
Ong Boon Leong authored
This patch restructures the per RX queue buffer allocation from page_pool to stmmac_alloc_rx_buffers(). We also rearrange dma_free_rx_skbufs() so that it can be used in init_dma_rx_desc_rings() during freeing of RX buffer in the event of page_pool allocation failure to replace the more efficient method earlier. The replacement is needed to make the RX buffer alloc and free method scalable to XDP ZC xsk_pool alloc and free later. Signed-off-by:
-
David S. Miller authored
Alex Elder says: ==================== net: ipa: add support for the SM8350 SoC This small series adds IPA driver support for the Qualcomm SM8350 SoC, which implements IPA v4.9. The first patch updates the DT binding, and depends on a previous patch that has already been accepted into net-next. The second just defines the IPA v4.9 configuration data file. (Device Tree files to support this SoC will be sent separately and will go through the Qualcomm tree.) ==================== Signed-off-by: -
Alex Elder authored
Add support for the SM8350 SoC, which includes IPA version 4.9. Signed-off-by:
Alex Elder <elder@linaro.org> Signed-off-by:
-
Alex Elder authored
Add support for "qcom,sm8350-ipa", which uses IPA v4.9. Use "enum" rather than "oneOf/const ..." to specify compatible strings, as suggested by Rob Herring. Signed-off-by:
-
Shannon Nelson authored
All the uses of HWTSTAMP_FILTER_* values need to be bit shifters, not straight values. v2: fixed subject and added Cc Dan and SoB Allen Fixes: f8ba81da ("ionic: add ethtool support for PTP") Cc: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Shannon Nelson <snelson@pensando.io> Signed-off-by:
Allen Hubbe <allenbh@pensando.io> Signed-off-by:
-
Lijun Pan authored
The reset process for ibmvnic commonly takes multiple seconds, clearly making it inappropriate for schedule_work/system_wq. The reason to make this change is that ibmvnic's use of the default system-wide workqueue for a relatively long-running work item can negatively affect other workqueue users. So, queue the relatively slow reset job to the system_long_wq. Suggested-by:
Nathan Lynch <nathanl@linux.ibm.com> Signed-off-by:
Lijun Pan <lijunp213@gmail.com> Signed-off-by:
-
David S. Miller authored
Merge tag 'linux-can-next-for-5.13-20210413' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next Marc Kleine-Budde says: ==================== pull-request: can-next 2021-04-13 this is a pull request of 14 patches for net-next/master. The first patch is by Yoshihiro Shimoda and updates the DT bindings for the rcar_can driver. Vincent Mailhol contributes 3 patches that add support for several ETAS USB CAN adapters. The final 10 patches are by me and clean up the peak_usb CAN driver. ==================== Signed-off-by:
-
Yang Li authored
Fix the following versioncheck warning: ./drivers/net/wireless/rsi/rsi_91x_ps.c: 19 linux/version.h not needed. Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Yang Li <yang.lee@linux.alibaba.com> Signed-off-by:
-
wengjianfeng authored
in st_nci_spi_write function, first assign a value to a variable then goto exit label. return statement just follow the label and exit label just used once, so we should directly return and remove exit label. Signed-off-by:
wengjianfeng <wengjianfeng@yulong.com> Signed-off-by:
-
Lijun Pan authored
The current implementation relies on H_IOCTL call to issue a H_SESSION_ERR_DETECTED command to let the hypervisor to send a failover signal. However, it may not work if there is no backup device or if the vnic is already in error state, e.g., "ibmvnic 30000003 env3: rx buffer returned with rc 6". Add a last resort, that is to schedule a failover reset via CRQ command. Signed-off-by:
-
Andreas Roeseler authored
The current icmp_rcv function drops all unknown ICMP types, including ICMP_EXT_ECHOREPLY (type 43). In order to parse Extended Echo Reply messages, we have to pass these packets to the ping_rcv function, which does not do any other filtering and passes the packet to the designated socket. Pass incoming RFC 8335 ICMP Extended Echo Reply packets to the ping_rcv handler instead of discarding the packet. Signed-off-by:
Andreas Roeseler <andreas.a.roeseler@gmail.com> Signed-off-by:
-
David S. Miller authored
Michael Walle says: ==================== of: net: support non-platform devices in of_get_mac_address() of_get_mac_address() is commonly used to fetch the MAC address from the device tree. It also supports reading it from a NVMEM provider. But the latter is only possible for platform devices, because only platform devices are searched for a matching device node. Add a second method to fetch the NVMEM cell by a device tree node instead of a "struct device". Moreover, the NVMEM subsystem will return dynamically allocated data which has to be freed after use. Currently, this is handled by allocating a device resource manged buffer to store the MAC address. of_get_mac_address() then returns a pointer to this buffer. Without a device, this trick is not possible anymore. Thus, change the of_get_mac_address() API to have the caller supply a buffer. It was considered to use the network device to attach the buffer to, but then the order matters and netdev_register() has to be called before of_get_mac_address(). No driver does it this way. ==================== Signed-off-by: -
Michael Walle authored
of_get_mac_address() already supports fetching the MAC address by an nvmem provider. But until now, it was just working for platform devices. Esp. it was not working for DSA ports and PCI devices. It gets more common that PCI devices have a device tree binding since SoCs contain integrated root complexes. Use the nvmem of_* binding to fetch the nvmem cells by a struct device_node. We still have to try to read the cell by device first because there might be a nvmem_cell_lookup associated with that device. Signed-off-by:
Michael Walle <michael@walle.cc> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Michael Walle authored
of_get_mac_address() returns a "const void*" pointer to a MAC address. Lately, support to fetch the MAC address by an NVMEM provider was added. But this will only work with platform devices. It will not work with PCI devices (e.g. of an integrated root complex) and esp. not with DSA ports. There is an of_* variant of the nvmem binding which works without devices. The returned data of a nvmem_cell_read() has to be freed after use. On the other hand the return of_get_mac_address() points to some static data without a lifetime. The trick for now, was to allocate a device resource managed buffer which is then returned. This will only work if we have an actual device. Change it, so that the caller of of_get_mac_address() has to supply a buffer where the MAC address is written to. Unfortunately, this will touch all drivers which use the of_get_mac_address(). Usually the code looks like: const char *addr; addr = of_get_mac_address(np); if (!IS_ERR(addr)) ether_addr_copy(ndev->dev_addr, addr); This can then be simply rewritten as: of_get_mac_address(np, ndev->dev_addr); Sometimes is_valid_ether_addr() is used to test the MAC address. of_get_mac_address() already makes sure, it just returns a valid MAC address. Thus we can just test its return code. But we have to be careful if there are still other sources for the MAC address before the of_get_mac_address(). In this case we have to keep the is_valid_ether_addr() call. The following coccinelle patch was used to convert common cases to the new style. Afterwards, I've manually gone over the drivers and fixed the return code variable: either used a new one or if one was already available use that. Mansour Moufid, thanks for that coccinelle patch! <spml> @A@ identifier x; expression y, z; @@ - x = of_get_mac_address(y); + x = of_get_mac_address(y, z); <... - ether_addr_copy(z, x); ...> @@ identifier a.x; @@ - if (<+... x ...+>) {} @@ identifier a.x; @@ if (<+... x ...+>) { ... } - else {} @@ identifier a.x; expression e; @@ - if (<+... x ...+>@e) - {} - else + if (!(e)) {...} @@ expression x, y, z; @@ - x = of_get_mac_address(y, z); + of_get_mac_address(y, z); ... when != x </spml> All drivers, except drivers/net/ethernet/aeroflex/greth.c, were compile-time tested. Suggested-by: -
René van Dorst authored
This patch adds EEE support. Signed-off-by:
René van Dorst <opensource@vdorst.com> Signed-off-by:
-
David S. Miller authored
Merge tag 'wireless-drivers-next-2021-04-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for v5.13 First set of patches for v5.13. I have been offline for a couple of and I have a smaller pull request this time. The next one will be bigger. Nothing really special standing out. ath11k * add initial support for QCN9074, but not enabled yet due to firmware problems * enable radar detection for 160MHz secondary segment * handle beacon misses in station mode rtw88 * 8822c: support firmware crash dump mt7601u * enable TDLS support ==================== Signed-off-by:
-
Marc Kleine-Budde authored
This patch replaces the open coded endianness conversion of unaligned data by the appropriate get/put_unaligned_leXX() variants. Link: https://lore.kernel.org/r/20210406111622.1874957-11-mkl@pengutronix.deAcked-by:
Stephane Grosjean <s.grosjean@peak-system.com> Tested-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Marc Kleine-Budde authored
The function serial_number is only called from one location with a valid serial_number pointer. Remove not needed NULL pointer check. Link: https://lore.kernel.org/r/20210406111622.1874957-10-mkl@pengutronix.deAcked-by:
-
Marc Kleine-Budde authored
This patch replaces the memcpy() + le32_to_cpu() by le32_to_cpup(). Link: https://lore.kernel.org/r/20210406111622.1874957-9-mkl@pengutronix.deAcked-by:
-
Marc Kleine-Budde authored
The caller of pcan_usb_get_serial() already prints an error message, so remove this one and return immediately. Link: https://lore.kernel.org/r/20210406111622.1874957-8-mkl@pengutronix.deAcked-by:
-
Marc Kleine-Budde authored
The callback struct peak_usb_adapter::dev_get_device_id, which is implemented by the functions pcan_usb_{,pro}_get_device_id() is only ever called with a valid device_id pointer. This patch removes the unneeded check if the device_id pointer is valid. Link: https://lore.kernel.org/r/20210406111622.1874957-7-mkl@pengutronix.deAcked-by: -
Marc Kleine-Budde authored
There's no need to iterate over all supported adapters to find the struct peak_usb_adapter that describes the currently probed devices's capabilities. The driver core gives us the information for free, if we assign it to the struct usb_device_id::driver_info. This patch assigns the usb_device_id::driver_info and converts peak_usb_probe() to make use of it. This reduces the driver size by 100 bytes on ARCH=arm. | add/remove: 0/1 grow/shrink: 0/1 up/down: 0/-124 (-124) | Function old new delta | peak_usb_adapters_list 24 - -24 | peak_usb_probe 236 136 -100 | Total: Before=25263, After=25139, chg -0.49% Link: https://lore.kernel.org/r/20210406111622.1874957-6-mkl@pengutronix.deAcked-by:
-
Marc Kleine-Budde authored
The variable struct peak_usb_adapter::ts_period is only ever written to. This patch removes it from the driver. Link: https://lore.kernel.org/r/20210406111622.1874957-5-mkl@pengutronix.deAcked-by:
-
Marc Kleine-Budde authored
This patch removes the unused variables struct peak_usb_device::echo_skb and struct peak_usb_device::bus_load from the driver. Link: https://lore.kernel.org/r/20210406111622.1874957-4-mkl@pengutronix.deAcked-by:
-
Marc Kleine-Budde authored
This patch replaces the double space indention after the u8 with a single space in pcan_usb_pro.h. Link: https://lore.kernel.org/r/20210406111622.1874957-3-mkl@pengutronix.deAcked-by:
-
Marc Kleine-Budde authored
This patch cleans several checkpatch warnings in the peak_usb driver. Link: https://lore.kernel.org/r/20210406111622.1874957-2-mkl@pengutronix.deAcked-by:
-
Vincent Mailhol authored
This patch add support for the ES582.1 and ES584.1 interfaces from ETAS GmbH (https://www.etas.com/en/products/es58x.php). Link: https://lore.kernel.org/r/20210410095948.233305-4-mailhol.vincent@wanadoo.frCo-developed-by:
Arunachalam Santhanam <arunachalam.santhanam@in.bosch.com> Signed-off-by:
Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by:
-
Vincent Mailhol authored
This patch adds support for the ES581.4 interface from ETAS GmbH (https://www.etas.com/en/products/es58x.php). Link: https://lore.kernel.org/r/20210410095948.233305-3-mailhol.vincent@wanadoo.frCo-developed-by:
-
Vincent Mailhol authored
This patch adds the core support for various USB CAN interfaces from ETAS GmbH (https://www.etas.com/en/products/es58x.php). The next patches add the glue code drivers for the individual interfaces. Link: https://lore.kernel.org/r/20210410095948.233305-2-mailhol.vincent@wanadoo.frCo-developed-by:
-
Yoshihiro Shimoda authored
Document SoC specific bindings for R-Car M3-W+ (r8a77961) SoC. Also as R8A7796 is now called R8A77960 so that update those references. Link: https://lore.kernel.org/r/20210409000020.2317696-1-yoshihiro.shimoda.uh@renesas.comSigned-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Acked-by:
Rob Herring <robh@kernel.org> Reviewed-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by:
-
- 12 Apr, 2021 6 commits
-
-
Adam Ford authored
For devices that use a programmable clock for the AVB reference clock, the driver may need to enable them. Add code to find the optional clock and enable it when available. Signed-off-by:
Adam Ford <aford173@gmail.com> Reviewed-by:
-
Adam Ford authored
The AVB driver assumes there is an external crystal, but it could be clocked by other means. In order to enable a programmable clock, it needs to be added to the clocks list and enabled in the driver. Since there currently only one clock, there is no clock-names list either. Update bindings to add the additional optional clock, and explicitly name both of them. Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@gmail.com> Signed-off-by:
-
David S. Miller authored
Yangbo Lu says: ==================== enetc: support PTP Sync packet one-step timestamping This patch-set is to add support for PTP Sync packet one-step timestamping. Since ENETC single-step register has to be configured dynamically per packet for correctionField offeset and UDP checksum update, current one-step timestamping packet has to be sent only when the last one completes transmitting on hardware. So, on the TX, this patch handles one-step timestamping packet as below: - Trasmit packet immediately if no other one in transfer, or queue to skb queue if there is already one in transfer. The test_and_set_bit_lock() is used here to lock and check state. - Start a work when complete transfer on hardware, to release the bit lock and to send one skb in skb queue if has. Changes for v2: - Rebased. - Fixed issues from patchwork checks. - netif_tx_lock for one-step timestamping packet sending. Changes for v3: - Used system workqueue. - Set bit lock when transmitted one-step packet, and scheduled work when completed. The worker cleared the bit lock, and transmitted one skb in skb queue if has, instead of a loop. ==================== Signed-off-by: -
Yangbo Lu authored
This patch is to add support for PTP Sync packet one-step timestamping. Since ENETC single-step register has to be configured dynamically per packet for correctionField offeset and UDP checksum update, current one-step timestamping packet has to be sent only when the last one completes transmitting on hardware. So, on the TX, this patch handles one-step timestamping packet as below: - Trasmit packet immediately if no other one in transfer, or queue to skb queue if there is already one in transfer. The test_and_set_bit_lock() is used here to lock and check state. - Start a work when complete transfer on hardware, to release the bit lock and to send one skb in skb queue if has. And the configuration for one-step timestamping on ENETC before transmitting is, - Set one-step timestamping flag in extension BD. - Write 30 bits current timestamp in tstamp field of extension BD. - Update PTP Sync packet originTimestamp field with current timestamp. - Configure single-step register for correctionField offeset and UDP checksum update. Signed-off-by:
Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by:
Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by:
-
Yangbo Lu authored
Mark TX timestamp type per skb on skb->cb[0], instead of global variable for all skbs. This is a preparation for one step timestamp support. For one-step timestamping enablement, there will be both one-step and two-step PTP messages to transfer. And a skb queue is needed for one-step PTP messages making sure start to send current message only after the last one completed on hardware. (ENETC single-step register has to be dynamically configured per message.) So, marking TX timestamp type per skb is required. Signed-off-by:
-
David S. Miller authored
Lijun Pan says: ==================== ibmvnic: improve error printing Patch 1 prints reset reason as a string. Patch 2 prints adapter state as a string. ==================== Signed-off-by:
-
