[Why]
Newer DCN should use optc3

[How]
Declare optc3 vmin/vmax function in header.
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

After some experimental tests, we noticed that we need to set
gpuvm_max_page_table_levels to '4' to meet the hardware requirements.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
For Pixel Rate control, when on HDMI, HDMI DTO should be selected
instead of DP DTO.

[How]
Pass HDMI parameter for HDMI stream, and select correct DTO.
Signed-off-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

For MPO we want to allocate less than maximum DET for MPO pipes because
we need enogh buffer to move DET back to other pipes when removing an
MPO plane. Also update regular DET allocation to use DET override (DCN32
has an internal policy which driver does not want to use)
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Currently, we check if pixel_encoding is equal to
PIXEL_ENCODING_YCBCR422 to get the k1/k2 div parameters. This commit
changes this logic slightly by checking if two pixels per container are
used.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Most of the time, a single display uses the ODM combine. When using
multi-display, we use ODM combine only if it is necessary. These cases
are not flexible enough for us, and we can improve them to take
advantage of our hardware. We want to have more control over the ODM
policy.

[How]
This commit add a new debug flag named
enable_single_display_2to1_odm_policy to control the ODM policy and
another flag named enable_dp_dig_pixel_rate_div_policy to fine control
the ODM combine. This is possible by adding a new "pipe.dest" parameter
that can be set to ODM 2:1 combined if we use a single display. For
dynamic ODM combine, when using DP-DIG, DCN applies K2=2 settings for
ODM combine. Note that this feature affects the following registers:

- timing.pix_clk_100khz -> DP_VID_M, DP_VID_N
- requested_pix_clk_100hz -> DP_DTOn_PHASE
- OTGn_PIXEL_RATE_DIVK2
- DP_PIXEL_PER_CYCLE_PROCESSING_MODE
- DIG_FIFO_OUTPUT_PIXEL_MODE
- DP_VID_N_MUL
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add function to set pixels per cycle in DIG stream encoder
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY]:
Lut pipeline will be hooked up differently in some asics
need to add new interfaces and missing registers.

[HOW]:
Add missing registers and hook up programming from DPP for pre-blend
lut.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Martin Leung <Martin.Leung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This commit enables the SubVP feature. To achieve that, we need to:

- Don't force p-state disallow on SubVP (can't block dummy p-state)
- Send calculated watermark to DMCUB for SubVP
- Adjust CAB mode message to PMFW
- Add a proper locking sequence for SubVP
- Various fixes to SubVP static analysis and determining SubVP config
- Currently SubVP not supported with pipe split so merge all pipes
  before setting up SubVp
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We are missing some ACP registers/mask value for some specific ASICs.
This commit includes it to those ASICs that support it.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

It should not init whole ras bad page framework on sriov guest side
due to it is handled on host side.
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

GFX is the only IP block that RAS TA needs to program
the hardware when receiving enable_feature command.

Changed from V1:
    remove amdgpu_ras_need_send_ras_feature inline function,
    use GFX RAS block check directly.
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

And bump the version to 0x2A.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We don't need to validate and map root PD specially here,
it would be validated and mapped by amdgpu_vm_validate_pt_bos
if it is evicted.

The special case is when turning a GFX VM to a compute VM,
if vm_update_mode changed, we should make sure root PD gets
mapped. So just map root PD after updating vm->update_funcs
in amdgpu_vm_make_compute whether the vm_update_mode changed
or not.

v3:
 - Add some comments suggested by Christian.

v2:
 - Don't rename vm_validate_pt_pd_bos and make it public.
Signed-off-by: Lang Yu <Lang.Yu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why&How]
Expose a new dc debug mask enum to force a subviewport memory clock switch
to facilitate easy testing.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Properly handle FP code in dcn32_clk_mgr.c.

Fixes: 265280b9 ("drm/amd/display: add CLKMGR changes for DCN32/321")
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

When we tried to compile DCN32/321 for 32-bit architecture, we got this
error message:

ERROR: modpost: "__nedf2" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!

This commit fixes this issue by rewriting a small part of the
dcn32_build_wm_range_table.

Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Fixes: 265280b9 ("drm/amd/display: add CLKMGR changes for DCN32/321")
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Sometimes when trying to enable some feature, we have to define some
values with educated guesses, but we mark those values as TBD, which
means "To Be Determined". However, the correct way to approach it is by
loading that information from the firmware. Anyway, some of the values
that we were experimenting with caused this issue:

ERROR: modpost: "__muldf3" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!

This commit fixes this issue by removing the division by two since it is
harmless in this case.

Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Fixes: 265280b9 ("drm/amd/display: add CLKMGR changes for DCN32/321")
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

When we tried to compile DCN32/321 for 32-bit architecture, we got this
error message:

ERROR: modpost: "__floatunsidf" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!

This was caused because we were trying to assign an unsigned int to a
double value which causes issues for 32-bit architecture. This issue can
be fixed by changing the value type.

Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Fixes: 265280b9 ("drm/amd/display: add CLKMGR changes for DCN32/321")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

While we tried to build amdgpu on i386, we got this error:

ERROR: modpost: "__umoddi3" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!

This commit fixes this issue by replacing the standard module operator
with div_u64_rem.

Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Fixes: d3dfceb5 ("drm/amd/display: Add dependant changes for DCN32/321")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Indicate SMI profiling events available.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The synchronize_rcu may take several ms, which noticeably slows down
applications close SMI event handle. Use call_rcu to free client->fifo
and client asynchronously and eliminate the synchronize_rcu call in the
user thread.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

SVM range unmapped from GPUs when range is unmapped from CPU, or with
xnack on from MMU notifier when range is evicted or migrated.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Output user queue eviction and restore event. User queue eviction may be
triggered by svm or userptr MMU notifier, TTM eviction, device suspend
and CRIU checkpoint and restore.

User queue restore may be rescheduled if eviction happens again while
restore.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

For migration start and end event, output timestamp when migration
starts, ends, svm range address and size, GPU id of migration source and
destination and svm range attributes,

Migration trigger could be prefetch, CPU or GPU page fault and TTM
eviction.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Use ktime_get_boottime_ns() as timestamp to correlate with other
APIs. Output timestamp when GPU recoverable fault starts and ends to
recover the fault, if migration happened or only GPU page table is
updated to recover, fault address, if read or write fault.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Process receive event from same process by default. Add a flag to be
able to receive event from all processes, this requires super user
permission.

Event using pid 0 to send the event to all processes, to keep the
default behavior of existing SMI events.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Define new system management interface event IDs for migration, GPU
recoverable page fault, user queues eviction, restore and unmap from
GPU events and corresponding event triggers, those will be implemented
in the following patches.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This reverts commit 8748de87
since drv enabled mes to access registers.
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Enable mes to access registers.

v2: squash mes sched ring enablement flag
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add mes register access routines:
1. read register
2. write register
3. wait register
4. write and wait register
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add misc op commands in mes11.
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

GFX10 and up have work group processors (WGP) and WGP mode is the native
compile mode.

KFD and ROCr have no visibility into whether a dispatch is operating
in CU or WGP mode.

Enforce CU masking to be pairwise continguous in enablement and
round robin distribute CUs across the SEs in a pairwise manner to
assume WGP mode at all times.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add common interface for mes misc op, including accessing register
interface.
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Update MES firmware api for accessing registers.
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Fixes this issue:
drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:5094: warning: expecting prototype for amdgpu_device_gpu_recover_imp(). Prototype was for amdgpu_device_gpu_recover() instead

Fixes: cf727044 ("drm/amdgpu: Rename amdgpu_device_gpu_recover_imp back to amdgpu_device_gpu_recover")
Reviewed-by: Kent Russell <kent.russell@amd.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Redundant if-else cases for repeater and non-repeater checks

[How]
Without changing the core logic, rearranged the code by removing
redundant checks
Signed-off-by: Chandan Vurdigere Nataraj <chandan.vurdigerenataraj@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why&How]
Some userspace expect a backwards compatible modifier on DCN32/321. For
hardware with num_pipes more than 16, we expose the most efficient
modifier first. As a fall back method, we need to expose slightly inefficient
modifier AMD_FMT_MOD_TILE_GFX9_64K_R_X after the best option.

Also set the number of packers to fixed value as required per hardware
documentation. This value is cached during hardware initialization and
can be read through the base driver.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why&How]
TA firmware is needed to enable HDCP.

Changes in v2:

Load separate firmware for PSP 13.0.0
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This symbol is missing documentation:

	drivers/gpu/drm/amd/include/amd_shared.h:224: warning: Enum value 'PP_GFX_DCS_MASK' not described in enum 'PP_FEATURE_MASK'

Document it.

Fixes: 680602d6 ("drm/amd/pm: enable DCS")
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>