Implement the TCG I2C Interface driver, as specified in the TCG PC
Client Platform TPM Profile (PTP) specification for TPM 2.0 v1.04
revision 14, section 8, I2C Interface Definition.

This driver supports Guard Times. That is, if required by the TPM, the
driver has to wait by a vendor-specific time after each I2C read/write.
The specific time is read from the TPM_I2C_INTERFACE_CAPABILITY register.

Unfortunately, the TCG specified almost but not quite compatible
register addresses. Therefore, the TIS register addresses need to be
mapped to I2C ones. The locality is stripped because for now, only
locality 0 is supported.

Add a sanity check to I2C reads of e.g. TPM_ACCESS and TPM_STS. This is
to detect communication errors and issues due to non-standard behaviour
(E.g. the clock stretching quirk in the BCM2835, see 4dbfb5f4). In
case the sanity check fails, attempt a retry.
Co-developed-by: Johannes Holland <johannes.holland@infineon.com>
Signed-off-by: Johannes Holland <johannes.holland@infineon.com>
Co-developed-by: Amir Mizinski <amirmizi6@gmail.com>
Signed-off-by: Amir Mizinski <amirmizi6@gmail.com>
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>

Some TPMs, e.g. those implementing the I2C variant of TIS, can verify
data transfers to/from the FIFO with a CRC. The CRC is calculated over
the entirety of the FIFO register. Since the phy_ops layer is not aware
when the core layer is done reading/writing the FIFO, CRC verification
must be triggered from the core layer. To this end, add an optional
phy_ops API call.
Co-developed-by: Johannes Holland <johannes.holland@infineon.com>
Signed-off-by: Johannes Holland <johannes.holland@infineon.com>
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>

Initial device to be supported by the upcoming tpm_tis_i2c driver. More
to be added later.
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>

In case a TPM in failure mode is detected, the TPM should be accessible
through a transparent communication channel for analysing purposes (e.g.
TPM_GetTestResult) or a field upgrade. Since a TPM in failure mode has
similar reduced functionality as in field upgrade mode, the flag
TPM_CHIP_FLAG_FIRMWARE_UPGRADE is also valid.

As described in TCG TPM Main Part1 Design Principles, Revision 116,
chapter 9.2.1. the TPM also allows an update function in case a TPM is
in failure mode.

If the TPM in failure mode is detected, the function tpm1_auto_startup()
sets TPM_CHIP_FLAG_FIRMWARE_UPGRADE flag, which is used later during
driver initialization/deinitialization to disable functionality which
makes no sense or will fail in the current TPM state. The following
functionality is affected:
 * Do not register TPM as a hwrng
 * Do not get pcr allocation
 * Do not register sysfs entries which provide information impossible to
   obtain in limited mode
Signed-off-by: Stefan Mahnke-Hartmann <stefan.mahnke-hartmann@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>

Pull vfs dcache updates from Al Viro:
 "The main part here is making parallel lookups safe for RT - making
  sure preemption is disabled in start_dir_add()/ end_dir_add() sections
  (on non-RT it's automatic, on RT it needs to to be done explicitly)
  and moving wakeups from __d_lookup_done() inside of such to the end of
  those sections.

  Wakeups can be safely delayed for as long as ->d_lock on in-lookup
  dentry is held; proving that has caught a bug in d_add_ci() that
  allows memory corruption when sufficiently bogus ntfs (or
  case-insensitive xfs) image is mounted. Easily fixed, fortunately"

* tag 'pull-work.dcache' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs/dcache: Move wakeup out of i_seq_dir write held region.
  fs/dcache: Move the wakeup from __d_lookup_done() to the caller.
  fs/dcache: Disable preemption on i_dir_seq write side on PREEMPT_RT
  d_add_ci(): make sure we don't miss d_lookup_done()

Pull vfs lseek updates from Al Viro:
 "Jason's lseek series.

  Saner handling of 'lseek should fail with ESPIPE' - this gets rid of
  the magical no_llseek thing and makes checks consistent.

  In particular, the ad-hoc "can we do splice via internal pipe" checks
  got saner (and somewhat more permissive, which is what Jason had been
  after, AFAICT)"

* tag 'pull-work.lseek' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: remove no_llseek
  fs: check FMODE_LSEEK to control internal pipe splicing
  vfio: do not set FMODE_LSEEK flag
  dma-buf: remove useless FMODE_LSEEK flag
  fs: do not compare against ->llseek
  fs: clear or set FMODE_LSEEK based on llseek function

Pull vfs namei updates from Al Viro:
 "RCU pathwalk cleanups.

  Storing sampled ->d_seq of the next dentry in nameidata simplifies
  life considerably, especially if we delay fetching ->d_inode until
  step_into()"

* tag 'pull-work.namei' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  step_into(): move fetching ->d_inode past handle_mounts()
  lookup_fast(): don't bother with inode
  follow_dotdot{,_rcu}(): don't bother with inode
  step_into(): lose inode argument
  namei: stash the sampled ->d_seq into nameidata
  namei: move clearing LOOKUP_RCU towards rcu_read_unlock()
  switch try_to_unlazy_next() to __legitimize_mnt()
  follow_dotdot{,_rcu}(): change calling conventions
  namei: get rid of pointless unlikely(read_seqcount_retry(...))
  __follow_mount_rcu(): verify that mount_lock remains unchanged

Pull folio updates from Matthew Wilcox:

 - Fix an accounting bug that made NR_FILE_DIRTY grow without limit
   when running xfstests

 - Convert more of mpage to use folios

 - Remove add_to_page_cache() and add_to_page_cache_locked()

 - Convert find_get_pages_range() to filemap_get_folios()

 - Improvements to the read_cache_page() family of functions

 - Remove a few unnecessary checks of PageError

 - Some straightforward filesystem conversions to use folios

 - Split PageMovable users out from address_space_operations into
   their own movable_operations

 - Convert aops->migratepage to aops->migrate_folio

 - Remove nobh support (Christoph Hellwig)

* tag 'folio-6.0' of git://git.infradead.org/users/willy/pagecache: (78 commits)
  fs: remove the NULL get_block case in mpage_writepages
  fs: don't call ->writepage from __mpage_writepage
  fs: remove the nobh helpers
  jfs: stop using the nobh helper
  ext2: remove nobh support
  ntfs3: refactor ntfs_writepages
  mm/folio-compat: Remove migration compatibility functions
  fs: Remove aops->migratepage()
  secretmem: Convert to migrate_folio
  hugetlb: Convert to migrate_folio
  aio: Convert to migrate_folio
  f2fs: Convert to filemap_migrate_folio()
  ubifs: Convert to filemap_migrate_folio()
  btrfs: Convert btrfs_migratepage to migrate_folio
  mm/migrate: Add filemap_migrate_folio()
  mm/migrate: Convert migrate_page() to migrate_folio()
  nfs: Convert to migrate_folio
  btrfs: Convert btree_migratepage to migrate_folio
  mm/migrate: Convert expected_page_refs() to folio_expected_refs()
  mm/migrate: Convert buffer_migrate_page() to buffer_migrate_folio()
  ...

Pull XArray/IDR updates from Matthew Wilcox:

 - Add appropriate might_alloc() annotations to the XArray APIs

 - Document that the IDR is deprecated

* tag 'xarray-6.0' of git://git.infradead.org/users/willy/xarray:
  IDR: Note that the IDR API is deprecated
  XArray: Add calls to might_alloc()

Pull cgroup updates from Tejun Heo:
 "Several core optimizations:

   - threadgroup_rwsem write locking is skipped when configuring
     controllers in empty subtrees.

     Combined with CLONE_INTO_CGROUP, this allows the common static
     usage pattern to not grab threadgroup_rwsem at all (glibc still
     doesn't seem ready for CLONE_INTO_CGROUP unfortunately).

   - threadgroup_rwsem used to be put into non-percpu mode by default
     due to latency concerns in specific use cases. There's no reason
     for everyone else to pay for it. Make the behavior optional.

   - psi no longer allocates memory when disabled.

  ... along with some code cleanups"

* tag 'cgroup-for-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: Skip subtree root in cgroup_update_dfl_csses()
  cgroup: remove "no" prefixed mount options
  cgroup: Make !percpu threadgroup_rwsem operations optional
  cgroup: Add "no" prefixed mount options
  cgroup: Elide write-locking threadgroup_rwsem when updating csses on an empty subtree
  cgroup.c: remove redundant check for mixable cgroup in cgroup_migrate_vet_dst
  cgroup.c: add helper __cset_cgroup_from_root to cleanup duplicated codes
  psi: dont alloc memory for psi by default

Merge tag 'flexible-array-transformations-UAPI-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux

Pull uapi flexible array update from Gustavo Silva:
 "A treewide patch that replaces zero-length arrays with flexible-array
  members in UAPI. This has been baking in linux-next for 5 weeks now.

  '-fstrict-flex-arrays=3' is coming and we need to land these changes
  to prevent issues like these in the short future:

    fs/minix/dir.c:337:3: warning: 'strcpy' will always overflow; destination buffer has size 0, but the source string has length 2 (including NUL byte) [-Wfortify-source]
		strcpy(de3->name, ".");
		^

  Since these are all [0] to [] changes, the risk to UAPI is nearly
  zero. If this breaks anything, we can use a union with a new member
  name"

Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=101836

* tag 'flexible-array-transformations-UAPI-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
  treewide: uapi: Replace zero-length arrays with flexible-array members

Merge tag 'linux-kselftest-next-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull Kselftest updates from Shuah Khan:

 - timers test build fixes and cleanups for new tool chains

 - removing khdr from kselftest framework and main Makefile

 - changes to test output messages to improve reports

* tag 'linux-kselftest-next-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (24 commits)
  Makefile: replace headers_install with headers for kselftest
  selftests/landlock: drop deprecated headers dependency
  selftests: timers: clocksource-switch: adapt to kselftest framework
  selftests: timers: clocksource-switch: add 'runtime' command line parameter
  selftests: timers: clocksource-switch: add command line switch to skip sanity check
  selftests: timers: clocksource-switch: sort includes
  selftests: timers: clocksource-switch: fix passing errors from child
  selftests: timers: inconsistency-check: adapt to kselftest framework
  selftests: timers: nanosleep: adapt to kselftest framework
  selftests: timers: fix declarations of main()
  selftests: timers: valid-adjtimex: build fix for newer toolchains
  Makefile: add headers_install to kselftest targets
  selftests: drop KSFT_KHDR_INSTALL make target
  selftests: stop using KSFT_KHDR_INSTALL
  selftests: drop khdr make target
  selftests: drivers/dma-buf: Improve message in selftest summary
  selftests/kcmp: Make the test output consistent and clear
  selftests:timers: globals don't need initialization to 0
  selftests/drivers/gpu: Add error messages to drm_mm.sh
  selftests/tpm2: increase timeout for kselftests
  ...

Merge tag 'linux-kselftest-kunit-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull KUnit updates from Shuah Khan:
 "This consists of several fixes and an important feature to discourage
  running KUnit tests on production systems. Running tests on a
  production system could leave the system in a bad state.

  Summary:

   - Add a new taint type, TAINT_TEST to signal that a test has been
     run.

     This should discourage people from running these tests on
     production systems, and to make it easier to tell if tests have
     been run accidentally (by loading the wrong configuration, etc)

   - Several documentation and tool enhancements and fixes"

* tag 'linux-kselftest-kunit-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (29 commits)
  Documentation: KUnit: Fix example with compilation error
  Documentation: kunit: Add CLI args for kunit_tool
  kcsan: test: Add a .kunitconfig to run KCSAN tests
  kunit: executor: Fix a memory leak on failure in kunit_filter_tests
  clk: explicitly disable CONFIG_UML_PCI_OVER_VIRTIO in .kunitconfig
  mmc: sdhci-of-aspeed: test: Use kunit_test_suite() macro
  nitro_enclaves: test: Use kunit_test_suite() macro
  thunderbolt: test: Use kunit_test_suite() macro
  kunit: flatten kunit_suite*** to kunit_suite** in .kunit_test_suites
  kunit: unify module and builtin suite definitions
  selftest: Taint kernel when test module loaded
  module: panic: Taint the kernel when selftest modules load
  Documentation: kunit: fix example run_kunit func to allow spaces in args
  Documentation: kunit: Cleanup run_wrapper, fix x-ref
  kunit: test.h: fix a kernel-doc markup
  kunit: tool: Enable virtio/PCI by default on UML
  kunit: tool: make --kunitconfig repeatable, blindly concat
  kunit: add coverage_uml.config to enable GCOV on UML
  kunit: tool: refactor internal kconfig handling, allow overriding
  kunit: tool: introduce --qemu_args
  ...

Pull documentation updates from Jonathan Corbet:
 "This was a moderately busy cycle for documentation, but nothing
  all that earth-shaking:

   - More Chinese translations, and an update to the Italian
     translations.

     The Japanese, Korean, and traditional Chinese translations
     are more-or-less unmaintained at this point, instead.

   - Some build-system performance improvements.

   - The removal of the archaic submitting-drivers.rst document,
     with the movement of what useful material that remained into
     other docs.

   - Improvements to sphinx-pre-install to, hopefully, give more
     useful suggestions.

   - A number of build-warning fixes

  Plus the usual collection of typo fixes, updates, and more"

* tag 'docs-6.0' of git://git.lwn.net/linux: (92 commits)
  docs: efi-stub: Fix paths for x86 / arm stubs
  Docs/zh_CN: Update the translation of sched-stats to 5.19-rc8
  Docs/zh_CN: Update the translation of pci to 5.19-rc8
  Docs/zh_CN: Update the translation of pci-iov-howto to 5.19-rc8
  Docs/zh_CN: Update the translation of usage to 5.19-rc8
  Docs/zh_CN: Update the translation of testing-overview to 5.19-rc8
  Docs/zh_CN: Update the translation of sparse to 5.19-rc8
  Docs/zh_CN: Update the translation of kasan to 5.19-rc8
  Docs/zh_CN: Update the translation of iio_configfs to 5.19-rc8
  doc:it_IT: align Italian documentation
  docs: Remove spurious tag from admin-guide/mm/overcommit-accounting.rst
  Documentation: process: Update email client instructions for Thunderbird
  docs: ABI: correct QEMU fw_cfg spec path
  doc/zh_CN: remove submitting-driver reference from docs
  docs: zh_TW: align to submitting-drivers removal
  docs: zh_CN: align to submitting-drivers removal
  docs: ko_KR: howto: remove reference to removed submitting-drivers
  docs: ja_JP: howto: remove reference to removed submitting-drivers
  docs: it_IT: align to submitting-drivers removal
  docs: process: remove outdated submitting-drivers.rst
  ...

Pull nolibc updates from Paul McKenney:
 "This provides nolibc updates, perhaps most notably improved testing
  via the 'cd tools/include/nolibc; make headers' command. This should
  be considered a smoke test. More thorough testing is in the works"

* tag 'nolibc.2022.07.27a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
  tools/nolibc: add a help target to list supported targets
  tools/nolibc: make the default target build the headers
  tools/nolibc: fix the makefile to also work as "make -C tools ..."
  tools/nolibc/stdio: Add format attribute to enable printf warnings
  tools/nolibc/stdlib: Support overflow checking for older compiler versions

Pull RCU updates from Paul McKenney:

 - Documentation updates

 - Miscellaneous fixes

 - Callback-offload updates, perhaps most notably a new
   RCU_NOCB_CPU_DEFAULT_ALL Kconfig option that causes all CPUs to be
   offloaded at boot time, regardless of kernel boot parameters.

   This is useful to battery-powered systems such as ChromeOS and
   Android. In addition, a new RCU_NOCB_CPU_CB_BOOST kernel boot
   parameter prevents offloaded callbacks from interfering with
   real-time workloads and with energy-efficiency mechanisms

 - Polled grace-period updates, perhaps most notably making these APIs
   account for both normal and expedited grace periods

 - Tasks RCU updates, perhaps most notably reducing the CPU overhead of
   RCU tasks trace grace periods by more than a factor of two on a
   system with 15,000 tasks.

   The reduction is expected to increase with the number of tasks, so it
   seems reasonable to hypothesize that a system with 150,000 tasks
   might see a 20-fold reduction in CPU overhead

 - Torture-test updates

 - Updates that merge RCU's dyntick-idle tracking into context tracking,
   thus reducing the overhead of transitioning to kernel mode from
   either idle or nohz_full userspace execution for kernels that track
   context independently of RCU.

   This is expected to be helpful primarily for kernels built with
   CONFIG_NO_HZ_FULL=y

* tag 'rcu.2022.07.26a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu: (98 commits)
  rcu: Add irqs-disabled indicator to expedited RCU CPU stall warnings
  rcu: Diagnose extended sync_rcu_do_polled_gp() loops
  rcu: Put panic_on_rcu_stall() after expedited RCU CPU stall warnings
  rcutorture: Test polled expedited grace-period primitives
  rcu: Add polled expedited grace-period primitives
  rcutorture: Verify that polled GP API sees synchronous grace periods
  rcu: Make Tiny RCU grace periods visible to polled APIs
  rcu: Make polled grace-period API account for expedited grace periods
  rcu: Switch polled grace-period APIs to ->gp_seq_polled
  rcu/nocb: Avoid polling when my_rdp->nocb_head_rdp list is empty
  rcu/nocb: Add option to opt rcuo kthreads out of RT priority
  rcu: Add nocb_cb_kthread check to rcu_is_callbacks_kthread()
  rcu/nocb: Add an option to offload all CPUs on boot
  rcu/nocb: Fix NOCB kthreads spawn failure with rcu_nocb_rdp_deoffload() direct call
  rcu/nocb: Invert rcu_state.barrier_mutex VS hotplug lock locking order
  rcu/nocb: Add/del rdp to iterate from rcuog itself
  rcu/tree: Add comment to describe GP-done condition in fqs loop
  rcu: Initialize first_gp_fqs at declaration in rcu_gp_fqs()
  rcu/kvfree: Remove useless monitor_todo flag
  rcu: Cleanup RCU urgency state for offline CPU
  ...

Pull crypto updates from Herbert Xu:
"API:

   - Make proc files report fips module name and version

  Algorithms:

   - Move generic SHA1 code into lib/crypto

   - Implement Chinese Remainder Theorem for RSA

   - Remove blake2s

   - Add XCTR with x86/arm64 acceleration

   - Add POLYVAL with x86/arm64 acceleration

   - Add HCTR2

   - Add ARIA

  Drivers:

   - Add support for new CCP/PSP device ID in ccp"

* tag 'v5.20-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (89 commits)
  crypto: tcrypt - Remove the static variable initialisations to NULL
  crypto: arm64/poly1305 - fix a read out-of-bound
  crypto: hisilicon/zip - Use the bitmap API to allocate bitmaps
  crypto: hisilicon/sec - fix auth key size error
  crypto: ccree - Remove a useless dma_supported() call
  crypto: ccp - Add support for new CCP/PSP device ID
  crypto: inside-secure - Add missing MODULE_DEVICE_TABLE for of
  crypto: hisilicon/hpre - don't use GFP_KERNEL to alloc mem during softirq
  crypto: testmgr - some more fixes to RSA test vectors
  cyrpto: powerpc/aes - delete the rebundant word "block" in comments
  hwrng: via - Fix comment typo
  crypto: twofish - Fix comment typo
  crypto: rmd160 - fix Kconfig "its" grammar
  crypto: keembay-ocs-ecc - Drop if with an always false condition
  Documentation: qat: rewrite description
  Documentation: qat: Use code block for qat sysfs example
  crypto: lib - add module license to libsha1
  crypto: lib - make the sha1 library optional
  crypto: lib - move lib/sha1.c into lib/crypto/
  crypto: fips - make proc files report fips module name and version
  ...

Pull random number generator updates from Jason Donenfeld:
 "Though there's been a decent amount of RNG-related development during
  this last cycle, not all of it is coming through this tree, as this
  cycle saw a shift toward tackling early boot time seeding issues,
  which took place in other trees as well.

  Here's a summary of the various patches:

   - The CONFIG_ARCH_RANDOM .config option and the "nordrand" boot
     option have been removed, as they overlapped with the more widely
     supported and more sensible options, CONFIG_RANDOM_TRUST_CPU and
     "random.trust_cpu". This change allowed simplifying a bit of arch
     code.

   - x86's RDRAND boot time test has been made a bit more robust, with
     RDRAND disabled if it's clearly producing bogus results. This would
     be a tip.git commit, technically, but I took it through random.git
     to avoid a large merge conflict.

   - The RNG has long since mixed in a timestamp very early in boot, on
     the premise that a computer that does the same things, but does so
     starting at different points in wall time, could be made to still
     produce a different RNG state. Unfortunately, the clock isn't set
     early in boot on all systems, so now we mix in that timestamp when
     the time is actually set.

   - User Mode Linux now uses the host OS's getrandom() syscall to
     generate a bootloader RNG seed and later on treats getrandom() as
     the platform's RDRAND-like faculty.

   - The arch_get_random_{seed_,}_long() family of functions is now
     arch_get_random_{seed_,}_longs(), which enables certain platforms,
     such as s390, to exploit considerable performance advantages from
     requesting multiple CPU random numbers at once, while at the same
     time compiling down to the same code as before on platforms like
     x86.

   - A small cleanup changing a cmpxchg() into a try_cmpxchg(), from
     Uros.

   - A comment spelling fix"

More info about other random number changes that come in through various
architecture trees in the full commentary in the pull request:

  https://lore.kernel.org/all/20220731232428.2219258-1-Jason@zx2c4.com/

* tag 'random-6.0-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
  random: correct spelling of "overwrites"
  random: handle archrandom with multiple longs
  um: seed rng using host OS rng
  random: use try_cmpxchg in _credit_init_bits
  timekeeping: contribute wall clock to rng on time change
  x86/rdrand: Remove "nordrand" flag in favor of "random.trust_cpu"
  random: remove CONFIG_ARCH_RANDOM

Pull fsverity update from Eric Biggers:
 "Just a small documentation update to mention the btrfs support"

* tag 'fsverity-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt:
  fs-verity: mention btrfs support

Pull integrity updates from Mimi Zohar:
 "Aside from the one EVM cleanup patch, all the other changes are kexec
  related.

  On different architectures different keyrings are used to verify the
  kexec'ed kernel image signature. Here are a number of preparatory
  cleanup patches and the patches themselves for making the keyrings -
  builtin_trusted_keyring, .machine, .secondary_trusted_keyring, and
  .platform - consistent across the different architectures"

* tag 'integrity-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
  kexec, KEYS, s390: Make use of built-in and secondary keyring for signature verification
  arm64: kexec_file: use more system keyrings to verify kernel image signature
  kexec, KEYS: make the code in bzImage64_verify_sig generic
  kexec: clean up arch_kexec_kernel_verify_sig
  kexec: drop weak attribute from functions
  kexec_file: drop weak attribute from functions
  evm: Use IS_ENABLED to initialize .enabled

Pull SafeSetID updates from Micah Morton:
 "This contains one commit that touches common kernel code, one that
  adds functionality internal to the SafeSetID LSM code, and a few other
  commits that only modify the SafeSetID LSM selftest.

  The commit that touches common kernel code simply adds an LSM hook in
  the setgroups() syscall that mirrors what is done for the existing LSM
  hooks in the setuid() and setgid() syscalls. This commit combined with
  the SafeSetID-specific one allow the LSM to filter setgroups() calls
  according to configured rule sets in the same way that is already done
  for setuid() and setgid()"

* tag 'safesetid-6.0' of https://github.com/micah-morton/linux:
  LSM: SafeSetID: add setgroups() testing to selftest
  LSM: SafeSetID: Add setgroups() security policy handling
  security: Add LSM hook to setgroups() syscall
  LSM: SafeSetID: add GID testing to selftest
  LSM: SafeSetID: selftest cleanup and prepare for GIDs
  LSM: SafeSetID: fix userns bug in selftest

Pull msack updates from Casey Schaufler:
 "Two minor code clean-ups for Smack.

  One removes a touch of dead code and the other replaces an instance of
  kzalloc + strncpy with kstrndup"

* tag 'Smack-for-6.0' of https://github.com/cschaufler/smack-next:
  smack: Remove the redundant lsm_inode_alloc
  smack: Replace kzalloc + strncpy with kstrndup

Pull LSM update from Paul Moore:
 "A maintainer change for the LSM layer: James has asked me to take over
  the day-to-day responsibilities so a single patch to update the
  MAINTAINER info"

* tag 'lsm-pr-20220801' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm:
  MAINTAINERS: update the LSM maintainer info

Pull audit updates from Paul Moore:
 "Two minor audit patches: on marks a function as static, the other
  removes a redundant length check"

* tag 'audit-pr-20220801' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
  audit: make is_audit_feature_set() static
  audit: remove redundant data_len check

Pull selinux updates from Paul Moore:
 "A relatively small set of patches for SELinux this time, eight patches
  in total with really only one significant change.

  The highlights are:

   - Add support for proper labeling of memfd_secret anonymous inodes.

     This will allow LSMs that implement the anonymous inode hooks to
     apply security policy to memfd_secret() fds.

   - Various small improvements to memory management: fixed leaks, freed
     memory when needed, boundary checks.

   - Hardened the selinux_audit_data struct with __randomize_layout.

   - A minor documentation tweak to fix a formatting/style issue"

* tag 'selinux-pr-20220801' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
  selinux: selinux_add_opt() callers free memory
  selinux: Add boundary check in put_entry()
  selinux: fix memleak in security_read_state_kernel()
  docs: selinux: add '=' signs to kernel boot options
  mm: create security context for memfd_secret inodes
  selinux: fix typos in comments
  selinux: drop unnecessary NULL check
  selinux: add __randomize_layout to selinux_audit_data

Pull hardening updates from Kees Cook:

 - Fix Sparse warnings with randomizd kstack (GONG, Ruiqi)

 - Replace uintptr_t with unsigned long in usercopy (Jason A. Donenfeld)

 - Fix Clang -Wforward warning in LKDTM (Justin Stitt)

 - Fix comment to correctly refer to STRICT_DEVMEM (Lukas Bulwahn)

 - Introduce dm-verity binding logic to LoadPin LSM (Matthias Kaehlcke)

 - Clean up warnings and overflow and KASAN tests (Kees Cook)

* tag 'hardening-v5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  dm: verity-loadpin: Drop use of dm_table_get_num_targets()
  kasan: test: Silence GCC 12 warnings
  drivers: lkdtm: fix clang -Wformat warning
  x86: mm: refer to the intended config STRICT_DEVMEM in a comment
  dm: verity-loadpin: Use CONFIG_SECURITY_LOADPIN_VERITY for conditional compilation
  LoadPin: Enable loading from trusted dm-verity devices
  dm: Add verity helpers for LoadPin
  stack: Declare {randomize_,}kstack_offset to fix Sparse warnings
  lib: overflow: Do not define 64-bit tests on 32-bit
  MAINTAINERS: Add a general "kernel hardening" section
  usercopy: use unsigned long instead of uintptr_t

Pull execve updates from Kees Cook:

 - Allow unsharing time namespace on vfork+exec (Andrei Vagin)

 - Replace usage of deprecated kmap APIs (Fabio M. De Francesco)

 - Fix spelling mistake (Zhang Jiaming)

* tag 'execve-v5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  exec: Call kmap_local_page() in copy_string_kernel()
  exec: Fix a spelling mistake
  selftests/timens: add a test for vfork+exit
  fs/exec: allow to unshare a time namespace on vfork+exec

Pull seccomp update from Kees Cook:

 - Fix Clang build warning (YiFei Zhu)

* tag 'seccomp-v5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  selftests/seccomp: Fix compile warning when CC=clang

Pull pstore updates from Kees Cook:

 - Migrate to modern acomp crypto interface (Ard Biesheuvel)

 - Use better return type for "rcnt" (Dan Carpenter)

* tag 'pstore-v5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  pstore/zone: cleanup "rcnt" type
  pstore: migrate to crypto acomp interface

Merge tag 'for-6.0/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper updates from Mike Snitzer:

 - Refactor DM core's mempool allocation so that it clearer by not being
   split acorss files.

 - Improve DM core's BLK_STS_DM_REQUEUE and BLK_STS_AGAIN handling.

 - Optimize DM core's more common bio splitting by eliminating the use
   of bio cloning with bio_split+bio_chain. Shift that cloning cost to
   the relatively unlikely dm_io requeue case that only occurs during
   error handling. Introduces dm_io_rewind() that will clone a bio that
   reflects the subset of the original bio that must be requeued.

 - Remove DM core's dm_table_get_num_targets() wrapper and audit all
   dm_table_get_target() callers.

 - Fix potential for OOM with DM writecache target by setting a default
   MAX_WRITEBACK_JOBS (set to 256MiB or 1/16 of total system memory,
   whichever is smaller).

 - Fix DM writecache target's stats that are reported through
   DM-specific table info.

 - Fix use-after-free crash in dm_sm_register_threshold_callback().

 - Refine DM core's Persistent Reservation handling in preparation for
   broader work Mike Christie is doing to add compatibility with
   Microsoft Windows Failover Cluster.

 - Fix various KASAN reported bugs in the DM raid target.

 - Fix DM raid target crash due to md_handle_request() bio splitting
   that recurses to block core without properly initializing the bio's
   bi_dev.

 - Fix some code comment typos and fix some Documentation formatting.

* tag 'for-6.0/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (29 commits)
  dm: fix dm-raid crash if md_handle_request() splits bio
  dm raid: fix address sanitizer warning in raid_resume
  dm raid: fix address sanitizer warning in raid_status
  dm: Start pr_preempt from the same starting path
  dm: Fix PR release handling for non All Registrants
  dm: Start pr_reserve from the same starting path
  dm: Allow dm_call_pr to be used for path searches
  dm: return early from dm_pr_call() if DM device is suspended
  dm thin: fix use-after-free crash in dm_sm_register_threshold_callback
  dm writecache: count number of blocks discarded, not number of discard bios
  dm writecache: count number of blocks written, not number of write bios
  dm writecache: count number of blocks read, not number of read bios
  dm writecache: return void from functions
  dm kcopyd: use __GFP_HIGHMEM when allocating pages
  dm writecache: set a default MAX_WRITEBACK_JOBS
  Documentation: dm writecache: Render status list as list
  Documentation: dm writecache: add blank line before optional parameters
  dm snapshot: fix typo in snapshot_map() comment
  dm raid: remove redundant "the" in parse_raid_params() comment
  dm cache: fix typo in 2 comment blocks
  ...

Pull block updates from Jens Axboe:

 - Improve the type checking of request flags (Bart)

 - Ensure queue mapping for a single queues always picks the right queue
   (Bart)

 - Sanitize the io priority handling (Jan)

 - rq-qos race fix (Jinke)

 - Reserved tags handling improvements (John)

 - Separate memory alignment from file/disk offset aligment for O_DIRECT
   (Keith)

 - Add new ublk driver, userspace block driver using io_uring for
   communication with the userspace backend (Ming)

 - Use try_cmpxchg() to cleanup the code in various spots (Uros)

 - Finally remove bdevname() (Christoph)

 - Clean up the zoned device handling (Christoph)

 - Clean up independent access range support (Christoph)

 - Clean up and improve block sysfs handling (Christoph)

 - Clean up and improve teardown of block devices.

   This turns the usual two step process into something that is simpler
   to implement and handle in block drivers (Christoph)

 - Clean up chunk size handling (Christoph)

 - Misc cleanups and fixes (Bart, Bo, Dan, GuoYong, Jason, Keith, Liu,
   Ming, Sebastian, Yang, Ying)

* tag 'for-5.20/block-2022-07-29' of git://git.kernel.dk/linux-block: (178 commits)
  ublk_drv: fix double shift bug
  ublk_drv: make sure that correct flags(features) returned to userspace
  ublk_drv: fix error handling of ublk_add_dev
  ublk_drv: fix lockdep warning
  block: remove __blk_get_queue
  block: call blk_mq_exit_queue from disk_release for never added disks
  blk-mq: fix error handling in __blk_mq_alloc_disk
  ublk: defer disk allocation
  ublk: rewrite ublk_ctrl_get_queue_affinity to not rely on hctx->cpumask
  ublk: fold __ublk_create_dev into ublk_ctrl_add_dev
  ublk: cleanup ublk_ctrl_uring_cmd
  ublk: simplify ublk_ch_open and ublk_ch_release
  ublk: remove the empty open and release block device operations
  ublk: remove UBLK_IO_F_PREFLUSH
  ublk: add a MAINTAINERS entry
  block: don't allow the same type rq_qos add more than once
  mmc: fix disk/queue leak in case of adding disk failure
  ublk_drv: fix an IS_ERR() vs NULL check
  ublk: remove UBLK_IO_F_INTEGRITY
  ublk_drv: remove unneeded semicolon
  ...

Pull io_uring zerocopy support from Jens Axboe:
 "This adds support for efficient support for zerocopy sends through
  io_uring. Both ipv4 and ipv6 is supported, as well as both TCP and
  UDP.

  The core network changes to support this is in a stable branch from
  Jakub that both io_uring and net-next has pulled in, and the io_uring
  changes are layered on top of that.

  All of the work has been done by Pavel"

* tag 'for-5.20/io_uring-zerocopy-send-2022-07-29' of git://git.kernel.dk/linux-block: (34 commits)
  io_uring: notification completion optimisation
  io_uring: export req alloc from core
  io_uring/net: use unsigned for flags
  io_uring/net: make page accounting more consistent
  io_uring/net: checks errors of zc mem accounting
  io_uring/net: improve io_get_notif_slot types
  selftests/io_uring: test zerocopy send
  io_uring: enable managed frags with register buffers
  io_uring: add zc notification flush requests
  io_uring: rename IORING_OP_FILES_UPDATE
  io_uring: flush notifiers after sendzc
  io_uring: sendzc with fixed buffers
  io_uring: allow to pass addr into sendzc
  io_uring: account locked pages for non-fixed zc
  io_uring: wire send zc request type
  io_uring: add notification slot registration
  io_uring: add rsrc referencing for notifiers
  io_uring: complete notifiers in tw
  io_uring: cache struct io_notif
  io_uring: add zc notification infrastructure
  ...

Pull io_uring buffered writes support from Jens Axboe:
 "This contains support for buffered writes, specifically for XFS. btrfs
  is in progress, will be coming in the next release.

  io_uring does support buffered writes on any file type, but since the
  buffered write path just always -EAGAIN (or -EOPNOTSUPP) any attempt
  to do so if IOCB_NOWAIT is set, any buffered write will effectively be
  handled by io-wq offload. This isn't very efficient, and we even have
  specific code in io-wq to serialize buffered writes to the same inode
  to avoid further inefficiencies with thread offload.

  This is particularly sad since most buffered writes don't block, they
  simply copy data to a page and dirty it. With this pull request, we
  can handle buffered writes a lot more effiently.

  If balance_dirty_pages() needs to block, we back off on writes as
  indicated.

  This improves buffered write support by 2-3x.

  Jan Kara helped with the mm bits for this, and Stefan handled the
  fs/iomap/xfs/io_uring parts of it"

* tag 'for-5.20/io_uring-buffered-writes-2022-07-29' of git://git.kernel.dk/linux-block:
  mm: honor FGP_NOWAIT for page cache page allocation
  xfs: Add async buffered write support
  xfs: Specify lockmode when calling xfs_ilock_for_iomap()
  io_uring: Add tracepoint for short writes
  io_uring: fix issue with io_write() not always undoing sb_start_write()
  io_uring: Add support for async buffered writes
  fs: Add async write file modification handling.
  fs: Split off inode_needs_update_time and __file_update_time
  fs: add __remove_file_privs() with flags parameter
  fs: add a FMODE_BUF_WASYNC flags for f_mode
  iomap: Return -EAGAIN from iomap_write_iter()
  iomap: Add async buffered write support
  iomap: Add flags parameter to iomap_page_create()
  mm: Add balance_dirty_pages_ratelimited_flags() function
  mm: Move updates of dirty_exceeded into one place
  mm: Move starting of background writeback into the main balancing loop

Pull io_uring updates from Jens Axboe:

 - As per (valid) complaint in the last merge window, fs/io_uring.c has
   grown quite large these days. io_uring isn't really tied to fs
   either, as it supports a wide variety of functionality outside of
   that.

   Move the code to io_uring/ and split it into files that either
   implement a specific request type, and split some code into helpers
   as well. The code is organized a lot better like this, and io_uring.c
   is now < 4K LOC (me).

 - Deprecate the epoll_ctl opcode. It'll still work, just trigger a
   warning once if used. If we don't get any complaints on this, and I
   don't expect any, then we can fully remove it in a future release
   (me).

 - Improve the cancel hash locking (Hao)

 - kbuf cleanups (Hao)

 - Efficiency improvements to the task_work handling (Dylan, Pavel)

 - Provided buffer improvements (Dylan)

 - Add support for recv/recvmsg multishot support. This is similar to
   the accept (or poll) support for have for multishot, where a single
   SQE can trigger everytime data is received. For applications that
   expect to do more than a few receives on an instantiated socket, this
   greatly improves efficiency (Dylan).

 - Efficiency improvements for poll handling (Pavel)

 - Poll cancelation improvements (Pavel)

 - Allow specifiying a range for direct descriptor allocations (Pavel)

 - Cleanup the cqe32 handling (Pavel)

 - Move io_uring types to greatly cleanup the tracing (Pavel)

 - Tons of great code cleanups and improvements (Pavel)

 - Add a way to do sync cancelations rather than through the sqe -> cqe
   interface, as that's a lot easier to use for some use cases (me).

 - Add support to IORING_OP_MSG_RING for sending direct descriptors to a
   different ring. This avoids the usually problematic SCM case, as we
   disallow those. (me)

 - Make the per-command alloc cache we use for apoll generic, place
   limits on it, and use it for netmsg as well (me).

 - Various cleanups (me, Michal, Gustavo, Uros)

* tag 'for-5.20/io_uring-2022-07-29' of git://git.kernel.dk/linux-block: (172 commits)
  io_uring: ensure REQ_F_ISREG is set async offload
  net: fix compat pointer in get_compat_msghdr()
  io_uring: Don't require reinitable percpu_ref
  io_uring: fix types in io_recvmsg_multishot_overflow
  io_uring: Use atomic_long_try_cmpxchg in __io_account_mem
  io_uring: support multishot in recvmsg
  net: copy from user before calling __get_compat_msghdr
  net: copy from user before calling __copy_msghdr
  io_uring: support 0 length iov in buffer select in compat
  io_uring: fix multishot ending when not polled
  io_uring: add netmsg cache
  io_uring: impose max limit on apoll cache
  io_uring: add abstraction around apoll cache
  io_uring: move apoll cache to poll.c
  io_uring: consolidate hash_locked io-wq handling
  io_uring: clear REQ_F_HASH_LOCKED on hash removal
  io_uring: don't race double poll setting REQ_F_ASYNC_DATA
  io_uring: don't miss setting REQ_F_DOUBLE_POLL
  io_uring: disable multishot recvmsg
  io_uring: only trace one of complete or overflow
  ...

Pull turbostat updates from Len Brown:
 "Only updating the turbostat tool here, no kernel changes"

* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  tools/power turbostat: version 2022.07.28
  tools/power turbostat: do not decode ACC for ICX and SPR
  tools/power turbostat: fix SPR PC6 limits
  tools/power turbostat: cleanup 'automatic_cstate_conversion_probe()'
  tools/power turbostat: separate SPR from ICX
  tools/power turbosstat: fix comment
  tools/power turbostat: Support RAPTORLAKE P
  tools/power turbostat: add support for ALDERLAKE_N
  tools/power turbostat: dump secondary Turbo-Ratio-Limit
  tools/power turbostat: simplify dump_turbo_ratio_limits()
  tools/power turbostat: dump CPUID.7.EDX.Hybrid
  tools/power turbostat: update turbostat.8
  tools/power turbostat: Show uncore frequency
  tools/power turbostat: Fix file pointer leak
  tools/power turbostat: replace strncmp with single character compare
  tools/power turbostat: print the kernel boot commandline
  tools/power turbostat: Introduce support for RaptorLake

Pull thermal control updates from Rafael Wysocki:
 "These start a rework of the handling of trip points in the thermal
  core, improve the cpufreq/devfreq cooling device handling, update some
  thermal control drivers and the tmon utility and clean up code.

  Specifics:

   - Consolidate the thermal core code by beginning to move the thermal
     trip structure from the thermal OF code as a generic structure to
     be used by the different sensors when registering a thermal zone
     (Daniel Lezcano).

   - Make per cpufreq / devfreq cooling device ops instead of using a
     global variable, fix comments and rework the trace information
     (Lukasz Luba).

   - Add the include/dt-bindings/thermal.h under the area covered by the
     thermal maintainer in the MAINTAINERS file (Lukas Bulwahn).

   - Improve the error output by giving the sensor identification when a
     thermal zone failed to initialize, the DT bindings by changing the
     positive logic and adding the r8a779f0 support on the rcar3
     (Wolfram Sang).

   - Convert the QCom tsens DT binding to the dtsformat format
     (Krzysztof Kozlowski).

   - Remove the pointless get_trend() function in the QCom, Ux500 and
     tegra thermal drivers, along with the unused DROP_FULL and
     RAISE_FULL trends definitions. Simplify the code by using clamp()
     macros (Daniel Lezcano).

   - Fix ref_table memory leak at probe time on the k3_j72xx bandgap
     (Bryan Brattlof).

   - Fix array underflow in prep_lookup_table (Dan Carpenter).

   - Add static annotation to the k3_j72xx_bandgap_j7* data structure
     (Jin Xiaoyun).

   - Fix typos in comments detected on sun8i by Coccinelle (Julia
     Lawall).

   - Fix typos in comments on rzg2l (Biju Das).

   - Remove as unnecessary call to dev_err() as the error is already
     printed by the failing function on u8500 (Yang Li).

   - Register the thermal zones as hwmon sensors for the Qcom thermal
     sensors (Dmitry Baryshkov).

   - Fix 'tmon' tool compilation issue by adding phtread.h include
     (Markus Mayer).

   - Fix typo in the comments for the 'tmon' tool (Slark Xiao).

   - Make the thermal core use ida_alloc()/free() directly instead of
     ida_simple_get()/ida_simple_remove() that have been deprecated
     (keliu).

   - Drop ACPI_FADT_LOW_POWER_S0 check from the Intel PCH thermal
     control driver (Rafael Wysocki)"

* tag 'thermal-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (39 commits)
  thermal/of: Initialize trip points separately
  thermal/of: Use thermal trips stored in the thermal zone
  thermal/core: Add thermal_trip in thermal_zone
  thermal/core: Rename 'trips' to 'num_trips'
  thermal/core: Move thermal_set_delay_jiffies to static
  thermal/core: Remove unneeded EXPORT_SYMBOLS
  thermal/of: Move thermal_trip structure to thermal.h
  thermal/of: Remove the device node pointer for thermal_trip
  thermal/of: Replace device node match with device node search
  thermal/core: Remove duplicate information when an error occurs
  thermal/core: Avoid calling ->get_trip_temp() unnecessarily
  thermal/tools/tmon: Fix typo 'the the' in comment
  thermal/tools/tmon: Include pthread and time headers in tmon.h
  thermal/ti-soc-thermal: Fix comment typo
  thermal/drivers/qcom/spmi-adc-tm5: Register thermal zones as hwmon sensors
  thermal/drivers/qcom/temp-alarm: Register thermal zones as hwmon sensors
  thermal/drivers/u8500: Remove unnecessary print function dev_err()
  thermal/drivers/rzg2l: Fix comments
  thermal/drivers/sun8i: Fix typo in comment
  thermal/drivers/k3_j72xx_bandgap: Make k3_j72xx_bandgap_j721e_data and k3_j72xx_bandgap_j7200_data static
  ...

Pull power management updates from Rafael Wysocki:
 "These are mostly minor improvements all over including new CPU IDs for
  the Intel RAPL driver, an Energy Model rework to use micro-Watt as the
  power unit, cpufreq fixes and cleanus, cpuidle updates, devfreq
  updates, documentation cleanups and a new version of the pm-graph
  suite of utilities.

  Specifics:

   - Make cpufreq_show_cpus() more straightforward (Viresh Kumar).

   - Drop unnecessary CPU hotplug locking from store() used by cpufreq
     sysfs attributes (Viresh Kumar).

   - Make the ACPI cpufreq driver support the boost control interface on
     Zhaoxin/Centaur processors (Tony W Wang-oc).

   - Print a warning message on attempts to free an active cpufreq
     policy which should never happen (Viresh Kumar).

   - Fix grammar in the Kconfig help text for the loongson2 cpufreq
     driver (Randy Dunlap).

   - Use cpumask_var_t for an on-stack CPU mask in the ondemand cpufreq
     governor (Zhao Liu).

   - Add trace points for guest_halt_poll_ns grow/shrink to the haltpoll
     cpuidle driver (Eiichi Tsukata).

   - Modify intel_idle to treat C1 and C1E as independent idle states on
     Sapphire Rapids (Artem Bityutskiy).

   - Extend support for wakeirq to callback wrappers used during system
     suspend and resume (Ulf Hansson).

   - Defer waiting for device probe before loading a hibernation image
     till the first actual device access to avoid possible deadlocks
     reported by syzbot (Tetsuo Handa).

   - Unify device_init_wakeup() for PM_SLEEP and !PM_SLEEP (Bjorn
     Helgaas).

   - Add Raptor Lake-P to the list of processors supported by the Intel
     RAPL driver (George D Sworo).

   - Add Alder Lake-N and Raptor Lake-P to the list of processors for
     which Power Limit4 is supported in the Intel RAPL driver (Sumeet
     Pawnikar).

   - Make pm_genpd_remove() check genpd_debugfs_dir against NULL before
     attempting to remove it (Hsin-Yi Wang).

   - Change the Energy Model code to represent power in micro-Watts and
     adjust its users accordingly (Lukasz Luba).

   - Add new devfreq driver for Mediatek CCI (Cache Coherent
     Interconnect) (Johnson Wang).

   - Convert the Samsung Exynos SoC Bus bindings to DT schema of
     exynos-bus.c (Krzysztof Kozlowski).

   - Address kernel-doc warnings by adding the description for unused
     function parameters in devfreq core (Mauro Carvalho Chehab).

   - Use NULL to pass a null pointer rather than zero according to the
     function propotype in imx-bus.c (Colin Ian King).

   - Print error message instead of error interger value in
     tegra30-devfreq.c (Dmitry Osipenko).

   - Add checks to prevent setting negative frequency QoS limits for
     CPUs (Shivnandan Kumar).

   - Update the pm-graph suite of utilities to the latest revision 5.9
     including multiple improvements (Todd Brandt).

   - Drop pme_interrupt reference from the PCI power management
     documentation (Mario Limonciello)"

* tag 'pm-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (27 commits)
  powercap: RAPL: Add Power Limit4 support for Alder Lake-N and Raptor Lake-P
  PM: QoS: Add check to make sure CPU freq is non-negative
  PM: hibernate: defer device probing when resuming from hibernation
  intel_idle: make SPR C1 and C1E be independent
  cpufreq: ondemand: Use cpumask_var_t for on-stack cpu mask
  cpufreq: loongson2: fix Kconfig "its" grammar
  pm-graph v5.9
  cpufreq: Warn users while freeing active policy
  cpufreq: scmi: Support the power scale in micro-Watts in SCMI v3.1
  firmware: arm_scmi: Get detailed power scale from perf
  Documentation: EM: Switch to micro-Watts scale
  PM: EM: convert power field to micro-Watts precision and align drivers
  PM / devfreq: tegra30: Add error message for devm_devfreq_add_device()
  PM / devfreq: imx-bus: use NULL to pass a null pointer rather than zero
  PM / devfreq: shut up kernel-doc warnings
  dt-bindings: interconnect: samsung,exynos-bus: convert to dtschema
  PM / devfreq: mediatek: Introduce MediaTek CCI devfreq driver
  dt-bindings: interconnect: Add MediaTek CCI dt-bindings
  PM: domains: Ensure genpd_debugfs_dir exists before remove
  PM: runtime: Extend support for wakeirq for force_suspend|resume
  ...

Pull ACPI updates from Rafael Wysocki:
 "These rework the handling of ACPI device objects to use the driver
  core facilities for managing child ones instead of some questionable
  home-grown ways without the requisite locking and reference counting,
  clean up the EC driver, improve suspend-to-idle handling on x86, add
  some systems to the ACPI backlight quirk list, fix some assorted
  issues, clean up code and improve documentation.

  Specifics:

   - Use facilities provided by the driver core and some additional
     helpers to handle the children of a given ACPI device object in
     multiple places instead of using the children and node list heads
     in struct acpi_device which is error prone (Rafael Wysocki).

   - Fix ACPI-related device reference counting issue in the hisi_lpc
     bus driver (Yang Yingliang).

   - Drop the children and node list heads that are not needed any more
     from struct acpi_device (Rafael Wysocki).

   - Drop driver member from struct acpi_device (Uwe Kleine-König).

   - Drop redundant check from acpi_device_remove() (Uwe Kleine-König).

   - Prepare the CPPC library for handling backwards-compatible future
     _CPC return package formats gracefully (Rafael Wysocki).

   - Clean up the ACPI EC driver after previous changes in it (Hans de
     Goede).

   - Drop leftover acpi_processor_get_limit_info() declaration (Riwen
     Lu).

   - Split out thermal initialization from ACPI PSS (Riwen Lu).

   - Annotate more functions in the ACPI CPU idle driver to live in the
     cpuidle section (Guilherme G. Piccoli).

   - Fix _EINJ vs "special purpose" EFI memory regions (Dan Williams).

   - Implement a better fix to avoid spamming the console with old error
     logs (Tony Luck).

   - Fix typo in a comment in the APEI code (Xiang wangx).

   - Save NVS memory during transitions into S3 on Lenovo G40-45 (Manyi
     Li).

   - Add support for upcoming AMD uPEP device ID AMDI008 to the ACPI
     suspend-to-idle driver for x86 platforms (Shyam Sundar S K).

   - Clean up checks related to the ACPI_FADT_LOW_POWER_S0 platform flag
     in the LPIT table driver and the suspend-to-idle driver for x86
     platforms (Rafael Wysocki).

   - Print information messages regarding declared LPS0 idle support in
     the platform firmware (Rafael Wysocki).

   - Fix missing check in register_device_clock() in the ACPI driver for
     Intel SoCs (huhai).

   - Fix ACS setup in the VIOT table parser (Eric Auger).

   - Skip IRQ override on AMD Zen platforms where it's harmful
     (Chuanhong Guo).

   - Use native backlight on Dell Inspiron N4010 (Hans de Goede).

   - Use native backlight on some TongFang devices (Werner Sembach).

   - Drop X86 dependency from the ACPI backlight driver Kconfig (Riwen
     Lu).

   - Shorten the quirk list in the ACPI backlight driver by identifying
     Clevo by board_name only (Werner Sembach).

   - Remove useless NULL pointer checks from 2 ACPI PCI link management
     functions (Andrey Strachuk).

   - Fix obsolete example in the ACPI EINJ documentation (Qifu Zhang).

   - Update links and references to _DSD-related documents (Sudeep
     Holla)"

* tag 'acpi-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (46 commits)
  ACPI/PCI: Remove useless NULL pointer checks
  ACPI: CPPC: Do not prevent CPPC from working in the future
  ACPI: PM: x86: Print messages regarding LPS0 idle support
  ACPI: resource: skip IRQ override on AMD Zen platforms
  Documentation: ACPI: EINJ: Fix obsolete example
  ACPI: video: Use native backlight on Dell Inspiron N4010
  ACPI: PM: s2idle: Use LPS0 idle if ACPI_FADT_LOW_POWER_S0 is unset
  Revert "ACPI / PM: LPIT: Register sysfs attributes based on FADT"
  ACPI: video: Shortening quirk list by identifying Clevo by board_name only
  ACPI: video: Force backlight native for some TongFang devices
  ACPI: PM: s2idle: Add support for upcoming AMD uPEP HID AMDI008
  ACPI: VIOT: Fix ACS setup
  ACPI: bus: Drop unused list heads from struct acpi_device
  hisi_lpc: Use acpi_dev_for_each_child()
  bus: hisi_lpc: fix missing platform_device_put() in hisi_lpc_acpi_probe()
  ACPI: bus: Drop driver member of struct acpi_device
  ACPI: bus: Drop redundant check in acpi_device_remove()
  ACPI: APEI: Fix _EINJ vs EFI_MEMORY_SP
  ACPI: LPSS: Fix missing check in register_device_clock()
  ACPI: APEI: Better fix to avoid spamming the console with old error logs
  ...

Pull hwmon updates from Guenter Roeck:

 - Substantial rewrite of lm90 driver to support several additional
   chips and improve support for existing chips.

 - Add support of ROG ZENITH II EXTREME, Maximus XI Hero, and
   Strix Z690-a D4 to asus-ec-sensors driver

 - Add support of F71858AD to f71882fg driver

 - Add support of Aquacomputer Quadro to aquacomputer_d5next driver

 - Improved assembler code and add support for Dell G5 5590 as well as
   XPS 13 7390 in dell-smm driver

 - Add support for ASUS TUF GAMING B550-PLUS WIFI II to nct775 driver

 - Add support for IEEE 754 half precision to PMBus core. Also support
   for Analog Devices LT7182S, improve regulator support, and report
   various MFR register values in debugfs.

 - Various other minor improvements and fixes

* tag 'hwmon-for-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (85 commits)
  hwmon: (aquacomputer_d5next) Add support for Aquacomputer Quadro fan controller
  hwmon: (dell-smm) Improve documentation
  hwmon: (nct6775) add ASUS TUF GAMING B550-PLUS WIFI II
  hwmon: (occ) Replace open-coded variant of %*phN specifier
  hwmon: (sht15) Fix wrong assumptions in device remove callback
  hwmon: (aquacomputer_d5next) Add support for reading the +12V voltage sensor on D5 Next
  hwmon: (tps23861) fix byte order in current and voltage registers
  hwmon: (aspeed-pwm-tacho) increase fan tach period (again)
  hwmon: (aquacomputer_d5next) Add D5 Next fan control support
  hwmon: (mcp3021) improve driver support for newer hwmon interface
  hwmon: (asus-ec-sensors) add definitions for ROG ZENITH II EXTREME
  hwmon: (aquacomputer_d5next) Move device-specific data into struct aqc_data
  hwmon: (asus-ec-sensors) add missing sensors for X570-I GAMING
  hwmon: (drivetemp) Add module alias
  hwmon: (asus_wmi_sensors) Save a few bytes of memory
  hwmon: (lm90) Use worker for alarm notifications
  hwmon: (asus-ec-sensors) add support for Maximus XI Hero
  hwmon: (dell-smm) Improve assembly code
  hwmon: (pmbus/ltc2978) Set voltage resolution
  hwmon: (pmbus) Add list_voltage to pmbus ops
  ...

Merge tag 'pwm/for-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm

Pull pwm updates from Thierry Reding:
 "After v5.19 had all drivers converted to the new atomic API and nobody
  has reported any breakage, this set of changes starts by dropping the
  legacy support.

  Some existing drivers get improvements and broader chip support and a
  new driver is added that emulates a PWM controller using a clock
  output.

  Other than that there's the usual bits of cleanups and minor fixes"

* tag 'pwm/for-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (21 commits)
  pwm: lpc18xx: Fix period handling
  pwm: lpc18xx: Convert to use dev_err_probe()
  pwm: twl-led: Document some limitations and link to the reference manual
  MAINTAINERS: Remove myself as PWM maintainer
  MAINTAINERS: Add include/dt-bindings/pwm to PWM SUBSYSTEM
  dt-bindings: pwm: mediatek: Add compatible string for MT8195
  pwm: Add clock based PWM output driver
  dt-bindings: pwm: Document clk based PWM controller
  pwm: sifive: Shut down hardware only after pwmchip_remove() completed
  pwm: sifive: Ensure the clk is enabled exactly once per running PWM
  pwm: sifive: Simplify clk handling
  pwm: sifive: Enable clk only after period check in .apply()
  pwm: sifive: Reduce time the controller lock is held
  pwm: sifive: Fold pwm_sifive_enable() into its only caller
  pwm: sifive: Simplify offset calculation for PWMCMP registers
  pwm: mediatek: Add MT8365 support
  dt-bindings: pwm: Add MT8365 SoC binding
  pwm: Drop unused forward declaration from pwm.h
  pwm: Reorder header file to get rid of struct pwm_capture forward declaration
  pwm: atmel-tcb: Fix typo in comment
  ...