Instantiating the rmi4 SPI transport driver without an interrupt assigned
caused the driver to fail to load, but it does not clean up its transport
device registration. Result may be a crash at a later time, for example
when rebooting the system.

Fixes: 8d99758d ("Input: synaptics-rmi4 - add SPI transport driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Tested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Here we introduce logic in alps_identify to set the ALPS_DUALPOINT flag
for touchpad hardware responding to E7 report with 73 03 28, as is found
in the Dell Latitude E7470.
Tested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The SS5 hardware can report this.
Tested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

While a button is held SS5 hardware will give us single-finger packets
with x, y, and pressure equal to zero. This causes annoying jumps in
pointer position if a touch is released while the button is held. Handle
this by claiming zero contacts to ensure that no position events are
provided to the user.
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add touchstick support for the so-called SS5 hardware, which uses a
variant of the SS4 protocol.
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Just like Fujitsu CELSIUS H730, the H760 also has an Elantech touchpad with
the same quirks. Without this patch, the touchpad is useless out-of-the-box
as the mouse pointer won't move.

This patch makes the driver aware of both the crc_enabled=1 requirement and
the middle button, making the touchpad fully functional out-of-the-box.
Signed-off-by: Matti Kurkela <Matti.Kurkela@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Reviewed-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

i2c_smbus_read_block_data() returns negative errno else the number of
data bytes in the slave's response.

Checking for error not null means the function always fails if the device
answers properly.

So given that we read 3 bytes and access those, better check that we
actually read those 3 bytes.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The newly added ektf2127 driver uses the SIMPLE_DEV_PM_OPS macro
to conditionally refer to the resume/suspend functions, which
causes a warning when CONFIG_PM_SLEEP is disabled:

drivers/input/touchscreen/ektf2127.c:168:12: error: 'ektf2127_resume' defined but not used [-Werror=unused-function]
drivers/input/touchscreen/ektf2127.c:156:12: error: 'ektf2127_suspend' defined but not used [-Werror=unused-function]

We could either put these functions inside of an #ifdef or
add __maybe_unused annotations. This uses the second approach,
which is generally more foolproof.

Fixes: 9ca5bf50 ("Input: add support for Elan eKTF2127 touchscreen controller")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Current code uses devm_input_allocate_device() so don't explicitly call
input_free_device if input_register_device fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This adds a driver for the Elan eKTF2127 touchscreen controller,
which speaks an i2c protocol which is distinctly different from
the already supported eKTH controllers.
Signed-off-by: Michel Verlaan <michel.verl@gmail.com>
Signed-off-by: Siebren Vroegindeweij <siebren.vroegindeweij@hotmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The Pulse-Eight USB CEC adapter is a usb device that shows up as a ttyACM0
device.  It requires that you run inputattach in order to communicate with
it via serio.

This all works well, but it would be nice to have a udev rule to
automatically start inputattach. That too works OK, but the problem comes
when the USB device is unplugged: the tty hangup is never handled by the
serio framework so the inputattach utility never exits and you have to kill
it manually.

By adding this hangup callback the inputattach utility now properly exits
as soon as the USB device is unplugged.

The udev rule I used on my Debian sid system is:

SUBSYSTEM=="tty", KERNEL=="ttyACM[0-9]*", ATTRS{idVendor}=="2548", ATTRS{idProduct}=="1002", ACTION=="add", TAG+="systemd", ENV{SYSTEMD_WANTS}+="pulse8-cec-inputattach@%k.service"

And /etc/systemd/system/pulse8-cec-inputattach@.service is as follows:

===============================================================
[Unit]
Description=inputattach for pulse8-cec device on %I

[Service]
Type=simple
ExecStart=/usr/local/bin/inputattach --pulse8-cec /dev/%I
KillMode=process
===============================================================
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The power button found in tps65217 device is very similar to the tps65218,
so let's enhance the driver to support both variants.

This driver enables us to use tps65217's power button as KEY_POWER on
am335x boards (directly connected button in chiliboard, accessible pin
via expansion header in beaglebone). This patch has been tested with
chiliboard.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Switch the jornada720 touchscreen driver to obtain its gpio from
the platform device via gpiolib and derive the interrupt from the
GPIO, rather than via a hard-coded interrupt number obtained from
the mach/irqs.h and mach/hardware.h headers.
Tested-by: Adam Wysocki <armlinux@chmurka.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The Jornada720 keyboard driver does not make use of anything from the
mach/hardware.h header, so this header can be removed.
Tested-by: Adam Wysocki <armlinux@chmurka.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We get 1 warning when building kernel with W=1:
drivers/input/mouse/focaltech.c:393:6: warning: no previous prototype for 'focaltech_set_resolution' [-Wmissing-prototypes]

In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
So this patch marks it 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The spec says that flash erase time is 30ms typical/200ms max, so let's
replace current 50ms wait with 200ms to avoid potential failures.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The change corrects an example in device tree documentation section,
because button/key device nodes don't contain reg property there is
no need to declare unit-address, and address and size cell properties
are also redundant.

At the moment a compilation of the hypothetical original example
should produce W=1 level warnings, and it is better to stop spreading
misusage of the polled gpio keys device tree binding through this
example.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add a driver to read group of GPIO lines and provide its status as a
numerical value as input event to the system. This will help in
interfacing devices, that can be connected over GPIOs, that provide
input to the system by driving GPIO lines connected to them like a
rotary dial or a switch.

For example, a rotary switch can be connected to four GPIO lines. The
status of the GPIO lines reflect the actual position of the rotary
switch dial. For example, if dial points to 9, then the four GPIO lines
connected to the switch will read HLLH(0b'1001 = 9). This value
can be reported as an ABS_* event to the input subsystem.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

A common way of multiplexing buttons on a single input in cheap devices is
to use a resistor ladder on an ADC. This driver supports that configuration
by polling an ADC channel provided by IIO.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

According to the kernel's guidelines, let's directly include the
workqueue functions we use.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We use hw version to construct name of file holding touchscreen firmware,
so let's try reading it even if touchscreen initialization fails (the
firmware supports reading product/hardware id even when device is in
recovery/boot mode).
Signed-off-by: Johnny Chuang <johnny.chuang@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

alloc_ordered_workqueue() replaces deprecated
create_singlethread_workqueue().

It queues work items via &wm->ts_reader and &wm->pen_event_work which map
to wm97xx_pen_irq_worker (handles a pen down interrupt) and
wm97xx_ts_reader (the touchscreen sample reader) respectively. Hence, an
ordered dedicated workqueue has been used.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The workqueue "workqueue" has a single workitem(&priv->work) and hence
doesn't require ordering. Also, it is not being used on a memory reclaim
path. Hence, the singlethreaded workqueue has been replaced with the use
of system_wq.

System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.

Workitem is sync cancelled in mc13783_ts_remove() to ensure that there
are no workitems pending when the driver is disconnected.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

alloc_ordered_workqueue() replaces the deprecated
create_singlethread_workqueue().

There are multiple work items on the work queue viz
&priv->dev3_register_work, &priv->recalib_wq, &psmouse->resync_work,
which require execution ordering. Hence, an ordered workqueue has been
used.

The workqueue is not being used on a memory reclaim path.  Hence,
WQ_MEM_RECLAIM has not been set.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Switch to using dev_dbg instead of naked printk so that output is uniform
with the other driver messages in the kernel.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Switch the jornada720 keyboard driver to obtain its interrupt from the
platform device, rather than via a hard-coded interrupt number obtained
from the mach/irqs.h header.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Switch the jornada720_kbd driver to use the devm_* APIs.  This is in
preparation to removing the mach/irqs.h include from this driver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Change my email address to kernel.org instead of Samsung one for the
purpose of any future contact.  The copyrights remain untouched and are
attributed to Samsung.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch fix the following checkpatch report:
Blank lines aren't necessary after an open brace
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Checkpatch complains about the text suggesting writing to
Free Software Foundation for GPLv2 license copy.
This patch remove that text.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The usage of of_device_get_match_data reduce the code size a bit.
Furthermore, it is better to use a standard function for
getting the match data.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The new(ish) ft6236 simply re-implements the M09 protocol of the
(much) older edt-ft5x06.c driver.

This commit removes this duplicate driver and adds the i2c ids and
dt compatible string to the edt-ft5x06.c driver to keep compatibility.

This commit also adds the standard touchscreen properties as optional
properties to the edt,ft5x06 binding, these were documented in the
focaltech,ft6236 bindingi, but were missing from the edt,ft5x06 doc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This is a driver for SiS 9200 family touchscreen controllers using I2C bus.
Signed-off-by: Mika Penttilä <mika.penttila@nextfour.com>
Acked-by: Tammy Tseng <tammy_tseng@sis.com>
Acked-by: Yuger Yu <yuger_yu@sis.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

"calibrate" attribute does not provide "show" methods and thus we should
not mark it as readable.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Some ASUS laptops were shipped with touchpads that require to be woken up
first, before trying to switch them into absolute reporting mode, otherwise
touchpad would fail to work while flooding the logs with:

	elan_i2c i2c-ELAN1000:00: invalid report id data (1)

Among affected devices are Asus E202SA, N552VW, X456UF, UX305CA, and
others. We detect such devices by checking the IC type and product ID
numbers and adjusting order of operations accordingly.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Reported-by: Chris Chiu <chiu@endlessm.com>
Reported-by: Vlad Glagolev <stealth@vaygr.net>
Tested-by: Vlad Glagolev <stealth@vaygr.net>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This driver adds support for Silead touchscreens. It has been tested
with GSL1680 and GSL3680 touch panels.

It supports ACPI and device tree enumeration. Screen resolution,
the maximum number of fingers supported and firmware name are
configurable.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Daniel Jansen <djaniboe@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The use of mixed psmouse_printk() and printk creates 2 lines in the log,
while the use of %*ph solves everything.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

It's not advisable to use this encoding, but to support existing devices
add support for this to the driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>