Firmare sends the logs only when it's internal ring buffer is full. But
if firmware crashes we need to retrieve the latest logs through diagnose
window. This is now done everytime the debugfs file is read.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Just to make them a bit easier to read and unify naming. 32 suffix
in the function name means that it will be a 32 bit transfer. If there's
no number a buffer is transfered instead.

Use void pointers to get rid of ugly casts.

Don't provide target address as a pointer, pass it by value. Same for
the value used in write32().
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Firmware log parameters can be controlled now with help of fwlog_mask
debugfs file.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Firmware sends binary logs with WMIX_DBGLOG_EVENTID event. Create
a buffer which stores the latest logs and which can be copied from
fwlog debugfs file with cp command.

To save memory firmware log support is enabled only when CONFIG_ATH6KL_DEBUG
is enabled.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Probe Request reporting will be needed for P2P and WPS, but some
firmware builds do not seem to like this when P2P is not enabled.
Since we do not yet enable P2P, the safest option here is to just
remove this call for now and bring it back as a more dynamic version
once ath6kl starts advertising support for P2P.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ERROR: "ath6kl_tm_rx_report_event"
[drivers/net/wireless/ath/ath6kl/ath6kl.ko] undefined
Reported-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This is port from the staging version of ath6kl. The interface to user space
is exactly same.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Make sparse check endianness with "make C=1".
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

P2P has special rules on when to include P2P IE(s) in Probe Response
frame based on the Probe Request frame. Handle P2P IE(s) separately
to follow these rules.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Edward Lu <elu@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Edward Lu <elu@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Edward Lu <elu@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Use WMI_TX_STATUS_EVENTID event to generate cfg80211_mgmt_tx_frame()
calls. Since we support only a single pending frame for now, use the
hardcoded cookie value 1 and store a copy of the pending frame in
the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Edward Lu <elu@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The target is not ready to accept addkey commands until the connect
event has been delivered, so delay these operations for the initial GTK.
In addition, properly set interface connected and mark netdev ready when
the AP mode setup has been completed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Need to use correct length field for association request frame and
parse the IEs to find WPA/WPS/RSN IE. In addition, copying of the
IE better make sure it fits in into the buffer to avoid buffer
overflows.

In addition, add the (Re)AssocReq IEs to the cfg80211 new station
event for user space.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Use cfg80211 add/del_beacon callbacks for starting/stopping AP mode and
set_beacon to update AP configuration (mainly, to update Beacon and
Probe Response IEs).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It would be at <dbgfs_root>/ieee80211/phyX/ath6kl/credit_dist_stats.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It would be at <debugfs_root>/ieee80211/phyX/ath6kl/tgt_stats.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Just initial debugfs changes. The debugfs directory would
be created at <debugfs_root>/ieee80211/phyX/ath6kl.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Current tx scatter gather implementation rolls back the entire
scatter setup in case of a failure in setting up just one packet
into the bundle. Instead of dopping the whole scatter setup,
send the packets available just before the failure one using
scatter gather I/O.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Patch "ath6kl: Fix buffer alignment for scatter-gather write" does
memmove for a length (scat_req->scat_list[i].len) which is not the
actual length of data that is suppossed to be moved. The right
lengh is packet->act_len + HTC_HDR_LENGTH. Using wrong length
for data move during buffer alignment causes system freeze after
the following WARN_ON and sometimes target assert.

WARNING: at drivers/net/wireless/ath/ath6kl/main.c:771 ath6k_credit_distribute+0x196/0x1a0
 [<ffffffffa051cf5f>] ath6kl_htc_rxmsg_pending_handler+0x83f/0xe00 [ath6kl]
 [<ffffffff8104a743>] ? __wake_up+0x53/0x70
 [<ffffffffa0518b18>] ath6kldev_intr_bh_handler+0x188/0x650 [ath6kl]
 [<ffffffffa052d316>] ath6kl_sdio_irq_handler+0x36/0x80 [ath6kl]
 [<ffffffff81492b3c>] sdio_irq_thread+0xfc/0x360
 [<ffffffff81051c52>] ? default_wake_function+0x12/0x20
 [<ffffffff81492a40>] ? sdio_claim_irq+0x220/0x220
 [<ffffffff81080c36>] kthread+0x96/0xa0
 [<ffffffff815b9fb4>] kernel_thread_helper+0x4/0x10
 [<ffffffff81080ba0>] ? kthread_worker_fn+0x190/0x190
 [<ffffffff815b9fb0>] ? gs_change+0x13/0x13
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

For now this is implemented so that if host supports power is kept in
the chip. If that's not supported, an error is returned and sdio stack
will remove the device during suspend.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

For non-scatter buffers, there is already a bounce buffer which
takes care of alignment. This patch is influenced by a rough patch of
Kalle.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This fixes AMSDU rx, otherwise it fails with the following warnings.

"802.3 AMSDU frame bound check failed"
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>