- 08 Jun, 2012 1 commit
-
-
Eyal Shapira authored
The current debugfs code contains too much code duplication of bolierplate code. Add some macro magic to avoid this and enable adding new debugfs entries by using just a few lines. Signed-off-by:
Eyal Shapira <eyal@wizery.com> Signed-off-by:
Luciano Coelho <coelho@ti.com>
-
- 07 Jun, 2012 6 commits
-
-
Grant Erickson authored
Add support for an external 26 MHz crystal source. [Changed wl->ref_clock to priv->ref_clock -- Luca.] Signed-off-by:
Grant Erickson <marathon96@gmail.com> Signed-off-by:
-
Ido Reis authored
In PG2 only the last frame in the aggregate buffer should be aligned to the sdio block size. This frame's header msb should be set to 0, while in all the previous frames in the aggregation buffer, this bit should be set to 1. [Add a HW op for setting the frame ctrl bit only for 18xx. Other minor cleanups - Arik] [Make the pre_pkt_send operation optional -- Luca] Signed-off-by:
Ido Reis <idor@ti.com> Signed-off-by:
Arik Nemtsov <arik@wizery.com> Signed-off-by:
-
Ido Reis authored
In PG2, the HW watchdog interrupt occupies bit0 of the event vector, and the SW watchdog is relocated to bit9. We perform the relocation globally, as there's only one watchdog bit on previous platforms (bit0). [Only mask in the new bit9 for platforms supporting it. This avoids spurious events on other platforms - Arik] Signed-off-by:
Orit Brayer <orit@ti.com> Signed-off-by:
-
Ido Reis authored
PG2 requires 4 new parameters that to be passed to the PHY. Use the actual PHY initialization struct size for the mem size of the PHY_INIT section, to account for additions in params. [Make sure PG1 still gets the original struct - Arik] Signed-off-by:
-
Ido Reis authored
PG2 has a unique chip id. It supports similar HW quirks. Signed-off-by:
-
Ido Reis authored
was hardcoded 252, now uses the parameters struct size. Signed-off-by:
-
- 06 Jun, 2012 11 commits
-
-
Victor Goldenshtein authored
Introduce “pactive” scan mode – which instructs the fw to perform a passive scan until an activity/energy is detected on these channels, once energy detected the channel becomes active. Signed-off-by:
Victor Goldenshtein <victorg@ti.com> Signed-off-by:
-
Eliad Peller authored
When comparing 2 ssids the ssid_len must be taken into account. Otherwise, a substring will be treated as equal. This bug might cause ssids to get scanned as public ssids (rather than hidden), resulting in broadcast probe request (instead of ssid-specific ones) Signed-off-by:
Eliad Peller <eliad@wizery.com> Signed-off-by:
-
Yoni Divinsky authored
Due to a need by the firmware when working in multirole the role id needs to be added to the structs of the following commands: CMD_CONNECTION_SCAN_CFG, CMD_CONNECTION_SCAN_SSID_CFG, CMD_START_PERIODIC_SCAN, CMD_STOP_PERIODIC_SCAN Signed-off-by:
Yoni Divinsky <yoni.divinsky@ti.com> Signed-off-by:
Igal Chernobelsky <igalc@ti.com> Signed-off-by:
-
Eliad Peller authored
We have to reconfigure the fw when erp protection should be enabled/disabled. Pass beacons containing changes in the ERP protection IE, so we could analyze them. Signed-off-by:
-
Eliad Peller authored
Send beacon loss events to userspace, so it will be able to initiate roaming before disconnection Signed-off-by:
-
Yoni Divinsky authored
If the driver received a watchdog interrupt then the assumption is that the fw is hanged. Avoid sending the stop fwlog command in case of a watchdog recovey to avoid waiting for the 2 seconds timeout of the command. Signed-off-by:
-
Arik Nemtsov authored
The 12xx set_key just calls the common wlcore_set_key function, in order to program the keys into the FW. The 18xx variant changes the spare block count when a GEM or TKIP key is set. Also modify the get_spare_blocks HW op for 18xx to return the correct numbers of spare blocks, according to what is currently set in FW. Signed-off-by:
-
Arik Nemtsov authored
Stop network queues during Tx flush, and also drop other internal mac80211 packets (mgmt) that may arrive when the queues are stopped. When flush is done all driver queues are clear, forcefully if needed. Protect the Tx flush operation with a new mutex, to prevent concurrency that can mess us queue state. Based on a patch by Eliad Peller <eliad@wizery.com> Signed-off-by:
-
Arik Nemtsov authored
Allow the driver to wake/stop the queues for multiple reasons. A queue is started when no stop-reasons exist. Convert all wake/stop queue calls to use the new API. Before, a stopped queue was almost synonymous a high-watermark on Tx. Remove a bit of code in wl12xx_tx_reset() that relied on it. Internal packets arriving from mac80211 are also discarded when a queue is stopped. A notable exception to this is the watermark reason, which is a "soft"-stop reason. We allow traffic to gradually come to a halt, but we don't mind spurious packets here and there. This is merely a flow regulation mechanism. Based on a similar patch by Eliad Peller <eliadWizery.com>. Signed-off-by:
-
Arik Nemtsov authored
Add a HW op for getting spare blocks. 12xx cards require 2 spare blocks for GEM encrypted SKBs, regardless of VIFs or keys programmed into the FW. 18xx cards require 2 spare blocks when there are any connected TKIP or GEM VIFs. For now always return 2 spare blocks, as this works with all networks. The special case TKIP/GEM functionality is added at a later patch. Signed-off-by:
-
Arik Nemtsov authored
18xx chips do not require extra space in the TKIP header. Introduce a new HW quirk to allow us to make this feature arch-specific. 12xx chip will now have this quirk. Signed-off-by:
-
- 05 Jun, 2012 22 commits
-
-
Victor Goldenshtein authored
In some multi role scenarios the driver might send multi roc requests without sending a croc first, the fw queues those requests and starts service the next roc request as soon as the driver sends a croc for the previous one. So, if the fw rocs on channel X and driver asks to roc also on channel Y, the fw will not start service Y (and will not send roc complete event for this request) until the driver releases the fw with croc X. Signed-off-by:
-
Victor Goldenshtein authored
The beacon early termination is not relevant for high basic rates, which doesn't contribute anything to the PS and only adds unnecessary FW work. Enable BET only if the basic rate is less than 9 Mbps. Signed-off-by:
Ziv Riesel <zivriesel@ti.com> Signed-off-by:
-
Victor Goldenshtein authored
Wrong fm_coex parameters were set during wl18xx init phase, fix it. Signed-off-by:
-
Victor Goldenshtein authored
Wrong fm_coex parameters were set during wl12xx init phase, fix it. Signed-off-by:
-
Arik Nemtsov authored
This BUG_ON also ignored the INTENDED_FW_RECOVERY flag. This would result in a BUG() when using the bug_on_recovery module parameter during multi-role. Signed-off-by:
-
Eliad Peller authored
In some cases, the ROC_COMPLETE event might exceed the current timeout (750 msec). Increase it to 1 sec. Signed-off-by:
-
Eliad Peller authored
On CHANGE_CHANNEL indication, we should flush all the queued tx frames, so they will be sent on the correct (current) channel. Signed-off-by:
-
Yoni Divinsky authored
In the enum conf_tx_ac CONF_TX_AC_ANY_TID should be 0xff to match the firmware's implementation. Signed-off-by:
-
Yoni Divinsky authored
The polarity should be set before the firmware is loaded since the firmware touches the same register. Access of the firmware and driver to the same register will cause a collision since there is no exclusion scheme. Signed-off-by:
-
Yoni Divinsky authored
In ieee80211.h the uapsd bit mask is defined such that VO=BIT(0), VI=BIT(1), BK=BIT(2), BE=BIT(3). The firmware uses the indexing as defined in the ieee80211 spec, meaning that VO=3, VI=2, BK=1, BE=0. In AP mode when adding peer wlcore needs to convert the indexing accordingly. Signed-off-by:
-
Eliad Peller authored
Save the ht_cap IE per-band, so we can configure different params to BG and A bands (we currently don't support MIMO on A band) [Small fix for rx_highest - Arik] Signed-off-by:
-
Arik Nemtsov authored
Add a dependency on mac80211 in Kconfig, and also replace some spaces with tabs. Reported-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
-
Assaf Azulay authored
With the new FW (sigle role X.3.8.0.108, multi role X.5.4.0.21) we are supporting 3 RX BA sessions, this change is to support this new ability. Signed-off-by:
Assaf Azulay <assaf@ti.com> Signed-off-by:
-
Igal Chernobelsky authored
Modify default parameters to reduce firmware BSS lose probability in congested environment. [Applied to 18xx configuration as well - Arik] Signed-off-by:
-
Eliad Peller authored
Make sure the deauth bcast gets sent [Make sure we are AP as well before the flush - Arik] Signed-off-by:
-
Eliad Peller authored
Multicast management frames (e.g. global deauth) should be sent out on the bcast link, rather than the global, which should be used only for pre-added stations (e.g. for auth/assoc resp). Signed-off-by:
-
Arik Nemtsov authored
We can't use cancel_delayed_work_sync() from functions that take the wl->mutex, since connection_loss_work also takes the mutex. This might result in a deadlock. Restructure the code so the work is synchronously canceled before taking the mutex. Avoid a bug where we would indefinitely delay the connection loss indication by re-queuing the connection loss work on consecutive beacon loss events. Cc: bartosz.markowski <bartosz.markowski@tieto.com> Signed-off-by:
-
Arik Nemtsov authored
In patch d7b63b9f we have raised the dynamic PS timeout to 200ms to improve user experience. Re-apply the change, since it was reverted in the wlcore split. Signed-off-by:
-
Eliad Peller authored
The dynamic PS timeout is meaningless in forced PS mode. Signed-off-by:
-
Arik Nemtsov authored
The "static" modifier was mistakenly forgotten for some functions. Signed-off-by:
-
Luciano Coelho authored
Commit 4afc37 (wlcore: reorder identify_chip and get_hw_info) broke support for wl127x chips. When we moved the identify_chip operation to an earlier stage (ie. to the probe function), we broke wl127x support because during HW init we would set the WLCORE_QUIRK_TX_BLOCKSIZE_ALIGN. To avoid this, set this quirk in the identify_chip operations and only force it to be unset if the bus module doesn't support it. We were doing the opposite and setting the flag if the bus module supports it. Signed-off-by: -
Assaf Azulay authored
as tcp check sum is going to be removed from firmware, and as there is a problem with getting dns in security when checksum is enabled, it was decided to disable it by default. for none security modes it can be enabled by module paramenter. Signed-off-by:
-
