- 24 Apr, 2018 33 commits
-
-
Lorenzo Bianconi authored
Fix mt76x2_temp_tx_alc_enabled routine since in order to enable tx_alc temperature compensation it necessary to take into account BIT(15) of MT_EE_TX_POWER_EXT_PA_5G eeprom info Fixes: 7bc04215 ("mt76: add driver code for MT76x2e") Signed-off-by:
Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Lorenzo Bianconi authored
Remove unnecessary MT_TX_ALC_CFG_4 configuration since the register value will be properly set according to the usage of an external power amplifier Signed-off-by:
Felix Fietkau <nbd@nbd.name> Signed-off-by:
-
Felix Fietkau authored
Do not attempt to reorder packets not part of a BA session Signed-off-by:
-
Felix Fietkau authored
Required for fast-rx and allows mac80211 to skip an unnnecessary check. Signed-off-by:
-
Felix Fietkau authored
Use cancel_delayed_work instead of cancel_delayed_work_sync Signed-off-by:
-
Felix Fietkau authored
There were a number of issues in the existing tx power handling code: 1. The EEPROM target power for chain 0 refers to the actual output power after the channel and bandwidth delta have been added to the initial channel gain. This means the delta values should not be added/subtracted for the rate power calculation 2. When power is reduced significantly, the initial channel gain underflows very quickly, while the per-rate power offsets are high. This miscalculation causes effective tx power to be increased when it should actually be lowered. Fix this by trying to adjust the channel gain to the lowest power from the rate table. In case of under- or overflow, compensate by adding an appropriate delta to the rate power values. This makes power configuration more accurate on a wider range of configurable values Signed-off-by:
-
Felix Fietkau authored
Avoids race conditions from mac80211 enqueueing tx packets before the tx-drop bit is cleared Signed-off-by:
-
Felix Fietkau authored
Signficantly improves throughput with some clients Signed-off-by:
-
Felix Fietkau authored
Allows the driver to control whether to send a BlockAckReq after waking up. MT76x2 needs this set to true, for MT7603 (to be submitted later) it needs to be false. Signed-off-by:
-
Lorenzo Bianconi authored
Add static qualifier to mt76x2_mac_reset routine and remove the prototype from mt76x2_mac.h since it is used just in mt76x2_init.c Signed-off-by:
-
Lorenzo Bianconi authored
Fix mcu initial configuration for tssi calibration on 5GHz band Fixes: 7bc04215 ("mt76: add driver code for MT76x2e") Signed-off-by:
-
Gustavo A. R. Silva authored
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by:
Jakub Kicinski <kubakici@wp.pl> Signed-off-by:
-
Ping-Ke Shih authored
Since the statements are identical, we can safely remove the statements. The commit 42e74946 ("rtlwifi: btcoexist: Fix if == else warnings in halbtc8821a1ant.c") had fixed the statements, but the commit c6821613 ("rtlwifi: btcoex: follow linux coding style") that converted coding style and upgraded btcoex didn't include the fix. Reported-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
-
Siva Rebbagondla authored
While performing cleanup, driver is messing with card->ocr value by not masking rocr against ocr_avail. Below panic is observed with some of the SDIO host controllers due to this. Issue is resolved by reverting incorrect modifications to vdd. [ 927.423821] mmc1: Invalid vdd 0x1f [ 927.423925] Modules linked in: rsi_sdio(+) cmac bnep arc4 rsi_91x mac80211 cfg80211 btrsi rfcomm bluetooth ecdh_generic [ 927.424073] CPU: 0 PID: 1624 Comm: insmod Tainted: G W 4.15.0-1000-caracalla #1 [ 927.424075] Hardware name: Dell Inc. Edge Gateway 3003/ , BIOS 01.00.06 01/22/2018 [ 927.424082] RIP: 0010:sdhci_set_power_noreg+0xdd/0x190[sdhci] [ 927.424085] RSP: 0018:ffffac3fc064b930 EFLAGS: 00010282 [ 927.424107] Call Trace: [ 927.424118] sdhci_set_power+0x5a/0x60 [sdhci] [ 927.424125] sdhci_set_ios+0x360/0x3b0 [sdhci] [ 927.424133] mmc_set_initial_state+0x92/0x120 [ 927.424137] mmc_power_up.part.34+0x33/0x1d0 [ 927.424141] mmc_power_up+0x17/0x20 [ 927.424147] mmc_sdio_runtime_resume+0x2d/0x50 [ 927.424151] mmc_runtime_resume+0x17/0x20 [ 927.424156] __rpm_callback+0xc4/0x200 [ 927.424161] ? idr_alloc_cyclic+0x57/0xd0 [ 927.424165] ? mmc_runtime_suspend+0x20/0x20 [ 927.424169] rpm_callback+0x24/0x80 [ 927.424172] ? mmc_runtime_suspend+0x20/0x20 [ 927.424176] rpm_resume+0x4b3/0x6c0 [ 927.424181] __pm_runtime_resume+0x4e/0x80 [ 927.424188] driver_probe_device+0x41/0x490 [ 927.424192] __driver_attach+0xdf/0xf0 [ 927.424196] ? driver_probe_device+0x490/0x490 [ 927.424201] bus_for_each_dev+0x6c/0xc0 [ 927.424205] driver_attach+0x1e/0x20 [ 927.424209] bus_add_driver+0x1f4/0x270 [ 927.424217] ? rsi_sdio_ack_intr+0x50/0x50 [rsi_sdio] [ 927.424221] driver_register+0x60/0xe0 [ 927.424227] ? rsi_sdio_ack_intr+0x50/0x50 [rsi_sdio] [ 927.424231] sdio_register_driver+0x20/0x30 [ 927.424237] rsi_module_init+0x16/0x40 [rsi_sdio] Signed-off-by:
Siva Rebbagondla <siva.rebbagondla@redpinesignals.com> Signed-off-by:
Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by:
-
Siva Rebbagondla authored
Following overflow kernel panic is observed on some platforms while loading the driver. It is fixed if dynamically allocated memory is passed to SDIO instead of static one [ 927.513963] nommu_map_sg: overflow 17d54064ba7c+20 of device mask ffffffff [ 927.517712] Modules linked in: rsi_sdio(+) cmac bnep arc4 rsi_91x mac80211 cfg80211 btrsi rfcomm bluetooth ecdh_generic snd_soc_sst_bytcr_rt5660 [ 927.517861] CPU: 0 PID: 1624 Comm: insmod Tainted: G W 4.15.0-1000 #1 [ 927.517870] RIP: 0010:sdhci_send_command+0x5f0/0xa90 [sdhci] [ 927.517873] RSP: 0000:ffffac3fc064b6d8 EFLAGS: 00010086 [ 927.517895] Call Trace: [ 927.517908] ? __schedule+0x3cd/0x890 [ 927.517915] ? mod_timer+0x17b/0x3c0 [ 927.517922] sdhci_request+0x7c/0xf0 [sdhci] [ 927.517928] __mmc_start_request+0x5a/0x170 [ 927.517932] mmc_start_request+0x74/0x90 [ 927.517936] mmc_wait_for_req+0x87/0xe0 [ 927.517940] mmc_io_rw_extended+0x2fd/0x330 [ 927.517946] ? mmc_wait_data_done+0x30/0x30 [ 927.517951] sdio_io_rw_ext_helper+0x160/0x210 [ 927.517956] sdio_writesb+0x1d/0x20 [ 927.517966] rsi_sdio_write_register_multiple+0x68/0x110 [rsi_sdio] [ 927.517976] rsi_hal_device_init+0x357/0x910 [rsi_91x] [ 927.517983] ? rsi_hal_device_init+0x357/0x910 [rsi_91x] [ 927.517990] rsi_probe+0x2c6/0x450 [rsi_sdio] [ 927.517995] sdio_bus_probe+0xfc/0x110 [ 927.518000] driver_probe_device+0x2b3/0x490 [ 927.518005] __driver_attach+0xdf/0xf0 [ 927.518008] ? driver_probe_device+0x490/0x490 [ 927.518014] bus_for_each_dev+0x6c/0xc0 [ 927.518018] driver_attach+0x1e/0x20 [ 927.518021] bus_add_driver+0x1f4/0x270 [ 927.518028] ? rsi_sdio_ack_intr+0x50/0x50 [rsi_sdio] [ 927.518031] driver_register+0x60/0xe0 [ 927.518038] ? rsi_sdio_ack_intr+0x50/0x50 [rsi_sdio] [ 927.518041] sdio_register_driver+0x20/0x30 [ 927.518047] rsi_module_init+0x16/0x40 [rsi_sdio] Signed-off-by:
-
Amitkumar Karwar authored
Currently 5GHz gets advertised even for the device which supports only 2.4Ghz band. This patch fixes the issue Signed-off-by:
-
Amitkumar Karwar authored
Power save is by default enabled for WLAN and BT coex mode. Signed-off-by:
-
Amitkumar Karwar authored
Currently TID is extracted by checking at specific offset in data frame. This approach doesn't work for some of the frames. This patch uses mac80211 API and do it correctly Signed-off-by:
-
Amitkumar Karwar authored
Maximum number of supported aggregation subframes has been increased to 8. This is the optimal number for the driver. Signed-off-by:
-
Amitkumar Karwar authored
Power save request should be sent on station interface. Virtual interface which is connected should be preferred. This patch resolves device not entering power save problem in certain situations Signed-off-by:
-
Amitkumar Karwar authored
Some device configuration flags need to be enabled while sending 'bootup params' internal frame to firmware. This patch takes care of it. Signed-off-by:
-
Amitkumar Karwar authored
Firmware's watchdog timer should be disabled as a part of reset sequence. This change fixes a firmware hang issue observed during stress tests. Signed-off-by:
-
Dan Carpenter authored
The issue here is that we allocate "data" and then set "data = PTR_ALIGN(data, 8);" and then we free the aligned pointer instead of the original pointer. kmalloc() pointers are already ARCH_SLAB_MINALIGN aligned which is 8 or more on everything except certain Xtensa variants. We decided that if the Xtensa people ever notice a bug here then we'll tell them the bug is on their side. ;) Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Prameela Rani Garnepudi authored
To support roaming below changes are done: * Station notify frame is send to firmware after sending assoc request. This will avoid dropping of first EAPOL frame due to delay in creation of station control block in firmware. * Data queues are unblocked after sending station notify in open mode, after configuring key in WEP mode, and after receiving EAPOL4 confirm in WPA mode. * Initial EAPOL frames priority is chaged to MGMT, rekey EAPOL frames priority changed to VO. Signed-off-by:
Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by:
-
Prameela Rani Garnepudi authored
80MHz clock for device should be enabled by default in TX command frame radio capabilities. Signed-off-by:
-
Prameela Rani Garnepudi authored
Descriptors preparation is moved to core instead of HAL to avoid synchronization issues in sending TX frames Signed-off-by:
-
Prameela Rani Garnepudi authored
All descriptor structures are in rsi_mgmt.h except this extended descriptor structure. Hence moving it to rsi_mgmt.h and also renaming to rsi_xtend_desc. Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in wiphy_warn warning message text Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Dmitry Lebed authored
DFS offload support implemented: - DFS_OFFLOAD feature is advertised depending on HW capabilities - CAC_STARTED event forwarding from HW implemented - start_radar_detection() callback now returning -ENOTSUPP if DFS_OFFLOAD is enabled Signed-off-by:
Dmitry Lebed <dlebed@quantenna.com> Signed-off-by:
-
Kalle Valo authored
Merge tag 'iwlwifi-next-for-kalle-2018-04-20' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next iwlwifi patches for 4.18 * implement Traffic Condition Monitor; * use TCM for scan and BT coex; * use TCM to detect when the AP doesn't support UAPSD properly; * some more work for the 22000 family of devices; * introduce AMSDU rate control offload; * a couple of clean-ups and bugfixes.
-
Roopa Prabhu authored
Fixes: b16fb418 ("net: fib_rules: add extack support") Signed-off-by:
Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Anders Roxell authored
Fixes: 192dc405 ("selftests: net: add tcp_mmap program") Signed-off-by:
Anders Roxell <anders.roxell@linaro.org> Signed-off-by:
-
Colin Ian King authored
Function dca_common_get_tag is local to the source and does not need to be in global scope, so make it static. Cleans up sparse warning: drivers/dca/dca-core.c:273:4: warning: symbol 'dca_common_get_tag' was not declared. Should it be static? Signed-off-by:
-
- 23 Apr, 2018 7 commits
-
-
David S. Miller authored
David Ahern says: ==================== net/ipv6: couple of fixes for rcu change to from So many details... I am thankful for all the robots running the permutations and tools. Two bug fixes from the rcu change to rt->from: 1. missing rcu lock in ip6_negative_advice 2. rcu dereferences in 2 sites ==================== Signed-off-by: -
David Ahern authored
kbuild test robot reported 2 uses of rt->from not properly accessed using rcu_dereference: 1. add rcu_dereference_protected to rt6_remove_exception_rt and make sure it is always called with rcu lock held. 2. change rt6_do_redirect to take a reference on 'from' when accessed the first time so it can be used the sceond time outside of the lock Fixes: a68886a6 ("net/ipv6: Make from in rt6_info rcu protected") Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
David Ahern authored
syzbot reported a suspicious rcu_dereference_check: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1b9/0x294 lib/dump_stack.c:113 lockdep_rcu_suspicious+0x14a/0x153 kernel/locking/lockdep.c:4592 rt6_check_expired+0x38b/0x3e0 net/ipv6/route.c:410 ip6_negative_advice+0x67/0xc0 net/ipv6/route.c:2204 dst_negative_advice include/net/sock.h:1786 [inline] sock_setsockopt+0x138f/0x1fe0 net/core/sock.c:1051 __sys_setsockopt+0x2df/0x390 net/socket.c:1899 SYSC_setsockopt net/socket.c:1914 [inline] SyS_setsockopt+0x34/0x50 net/socket.c:1911 Add rcu locking around call to rt6_check_expired in ip6_negative_advice. Fixes: a68886a6 ("net/ipv6: Make from in rt6_info rcu protected") Reported-by: syzbot+2422c9e35796659d2273@syzkaller.appspotmail.com Signed-off-by:
-
David S. Miller authored
Denis Bolotin says: ==================== Add configuration information to register dump and debug data The purpose of this patchset is to add configuration information to the debug data collection, which already contains register dump. The first patch (removing the ptt) is essential because it prevents the unnecessary ptt acquirement when calling mcp APIs. ==================== Signed-off-by: -
Denis Bolotin authored
Configuration information is added to the debug data collection, in addition to register dump. Added qed_dbg_nvm_image() that receives an image type, allocates a buffer and reads the image. The images are saved in the buffers and the dump size is updated. Signed-off-by:
Denis Bolotin <denis.bolotin@cavium.com> Signed-off-by:
Ariel Elior <ariel.elior@cavium.com> Signed-off-by:
-
Denis Bolotin authored
Since nvm images attributes are cached during driver load, acquiring ptt is not needed when calling qed_mcp_get_nvm_image(). Signed-off-by:
-
Jose Abreu authored
Move all the core version detection to a common place ("hwif.c") and implement a table which can be used to lookup the correct callbacks for each IP version. This simplifies the initialization flow of each IP version and eases future implementation of new IP versions. Signed-off-by:Jose Abreu <joabreu@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Joao Pinto <jpinto@synopsys.com> Cc: Vitor Soares <soares@synopsys.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by:
-
