Things like vblank/err irq masks, mode of operation (command mode or not)
are derivative of the interface and mixer state. Therefore, they need to
be a part of the CRTC state too.

Add them to mdp5_crtc_state, and assign them in the CRTC's atomic_check()
func, so that it can be rolled back to a clean state.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

The INTF and CTL used in a display pipeline are going to be maintained as
a part of the CRTC state (i.e, in mdp5_crtc_state).

These entities, however, are currently statically assigned to drm_encoders
(i.e. mdp5_encoder). Since these aren't directly visible to the CRTC, we
assign them to the CRTC state in the encoder's atomic_check() op.

With this approach, we assign portions of CRTC state in two different
places: the layer mixer in CRTC's atomic_check(), and the INTF and CTL
pieces in the encoder's atomic_check() op.

We'd have more options here if the drm core maintained encoder state too,
but the current approach of clubbing everything in CRTC's state works just
fine.

Unlike hwpipes and mixers, we don't need to keep a track of INTF/CTL
assignments in the global atomic state. This is because they're currently
not sharable resources. For example, INTF0 and CTL0 will always be assigned
to one drm_encoder. This can change later when we implement writeback and
want a CRTC to use a CTL for a while, and then release it for others to use
it. Or, when a drm_encoder can switch between using a single INTF vs
2 INTFs.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Add the stuff needed to allow dynamically assigning a mixer to a CRTC.

Since mixers are a resource that can be shared across multiple CRTCs, we
need to maintain a 'hwmixer_to_crtc' map in the global atomic state,
acquire the mdp5_kms.state_lock modeset lock and so on.

The mixer is assigned in the CRTC's atomic_check() func, a failure will
result in the new state being cleanly rolled back.

The mixer assignment itself is straightforward, and almost identical to
what we do for hwpipes. We don't need to grab the old hwmixer_to_crtc
state like we do in hwpipes since we don't need to compare anything
with the old state at the moment.

The only LM capability we care about at the moment is whether the mixer
instance can be used to display stuff (i.e, connect to an INTF
downstream).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Subclass drm_crtc_state so that we can maintain additional state for
our CRTCs.

Add mdp5_pipeline and mdp5_ctl pointers in the subclassed state.
mdp5_pipeline is a grouping of the HW entities that forms the downstream
pipeline for a particular CRTC. It currently contains pointers to
mdp5_interface and mdp5_hw_mixer tied to this CRTC. Later, we will
have 2 hwmixers in this struct. (We could also have 2 intfs if we want
to support dual DSI with Source Split enabled. Implementing that feature
isn't planned at the moment).

The mdp5_pipeline state isn't used at the moment. For now, we just
introduce mdp5_crtc_state and the crtc funcs needed to manage the
subclassed state.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

The mdp5_ctl has an 'op_mode' struct which contains info on
the downstream pipeline.

Grouping these params together in a struct doesn't serve much
purpose in the code. Maybe there was a plan to expand this
further that never happened.

Remove the op_mode struct, and place its members directly in
mdp5_ctl. This will help avoid confusion later when I introduce
my own verion of a mdp5 pipeline :)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

mdp5_interface struct contains data corresponding to a INTF
instance in MDP5 hardware. This sturct is memcpy'd to the
mdp5_encoder struct, and then later to the mdp5_ctl struct.

Instead of copying around interface data, create mdp5_interface
instances in mdp5_init, like how it's done currently done for
pipes and layer mixers. Pass around the interface pointers to
mdp5_encoder and mdp5_ctl. This simplifies the code, and allows
us to decouple encoders from INTFs in the future if needed.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

PingPong ID for a Layer Mixer is already contained in
mdp5_hw_mixer.

This avoids the need to retrieve PP ID using macros
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Use the mdp5_hw_mixer struct in the mdp5_crtc and mdp5_ctl instead of
using the LM index.

Like before, the Layer Mixers are assigned statically to the CRTCs.
The hwmixer(s) will later be dynamically assigned to CRTCs.

For now, ignore the hwmixers that can only do WB.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Create a struct to represent MDP5 Layer Mixer instances. This will
eventually allow us to detach CRTCs from the Layer Mixers, and
generally clean things up a bit.

This is very similar to how hwpipes were previously abstracted away
from drm planes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

The number of Layer Mixers and the downstream blocks (DSPPs and PPs)
connected to each LM can vary with different MDP5 revisions. These
parameters are also static.

Keep the per instance LM data in mdp5_cfg. This will avoid the need
to have macros which identify PP id or DSPP id the LM is connected
to. We don't configure DSPPs at the moment, but keeping the DSPP
instance # here might come handy later.

Also add a 'caps' field that identifies features supported by a
LM instance. Introduce the caps MDP_LM_CAP_DISPLAY and MDP_LM_CAP_WB
that identify whether a LM instance can be used for display or
writeback.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

We'd previously moved the pipe_lock spinlock to the hwpipe struct. Bring
it back to mdp5_plane. We will need this because an mdp5_plane in the
future could comprise of 2 hw pipes. It makes more sense to have a single
lock to protect the registers for the hw pipes used by a plane, rather
than trying to take individual locks per hwpipe when committing a
configuration.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

4 macros already defined in hdmi.h,
which is not required to redefine in hdmi_audio.c
Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>

'SSPP_MAX + 1' is the max number of hwpipes that can be present on a
MDP5 platform. Recently, 2 new cursor hwpipes were added, which
caused overflows in arrays that used SSPP_MAX to represent the number
of elements. Update the SSPP_MAX value to incorporate the extra
hwpipes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

A recent commit introduces a bug in dsi_mgr_phy_enable. In the non
dual DSI mode, we reset the mdsi (master DSI) PHY. This isn't right
since master and slave DSI exist only in dual DSI mode. For the normal
mode of operation, we should simply reset the PHY of the DSI device
(i.e. msm_dsi) corresponding to the current bridge.

Usage of the wrong DSI pointer also resulted in a static checker
warning. That too is resolved with this fix.

Fixes: b62aa70a (drm/msm/dsi: Move PHY operations out of host)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Zero sized buffer objects tend to make various bits of the GEM
infrastructure complain:

 WARNING: CPU: 1 PID: 2323 at drivers/gpu/drm/drm_mm.c:389 drm_mm_insert_node_generic+0x258/0x2f0
 Modules linked in:

 CPU: 1 PID: 2323 Comm: drm-api-test Tainted: G        W 4.9.0-rc4-00906-g693af44 #213
 Hardware name: Qualcomm Technologies, Inc. DB820c (DT)
 task: ffff8000d7353400 task.stack: ffff8000d7720000
 PC is at drm_mm_insert_node_generic+0x258/0x2f0
 LR is at drm_vma_offset_add+0x4c/0x70

Zero sized buffers serve no appreciable value to the user so disallow
them at create time.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Output the upper 32 bits of a 64 bit iova in the RD_CMDSTREAM_ADDR
section while maintaining backwards compatibility for tools that
only understand 32 bit iovas.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

The interrupt status was being cleared before processing the handlers.
a5xx_rbbm_err_irq() was checking the interrupt status again, which would
likely turn out bad because the interrupt status would be 0 (or at least
different). Pass the original status to the function instead.

Also, skip clearing RBBM_AHB_ERROR from the interrupt status. The interrupt
will keep firing until the error source is cleared.  Skip the clear to
avoid a storm until the error is cleared in a5xx_rbbm_err_irq().
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

priv->num_aspaces is increased and then checked to see if it still fits
in the priv->aspace array.  If it doesn't, we warn and exit but
priv->num_aspaces remains incremented.

Don't incremement the count until we know that it fits in the array.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Instead of checking for a5xx_gpu->gpmu_iova during destroy we
accidently check a5xx_gpu->gpmu_bo.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

The core takes care of handling the send_event vs. close() issues, we
can remove that driver code.

Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>

I didn't spot anything that would require ordering here (well not
anywhere else either), and I'm trying to unify at least modern drivers
on one close hook.

Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>

The newly added a5xx support fails to build when debugfs is diabled:

drivers/gpu/drm/msm/adreno/a5xx_gpu.c:849:4: error: 'struct msm_gpu_funcs' has no member named 'show'
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:849:11: error: 'a5xx_show' undeclared here (not in a function); did you mean 'a5xx_irq'?

This adds a missing #ifdef.

Fixes: b5f103ab ("drm/msm: gpu: Add A5XX target support")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Probably a symptom of needing finer grained locking, but if we wait on
the incoming fence-fd (which could come from a different context) while
holding struct_mutex, that blocks retire_worker so gpu fences cannot get
signalled.

This causes a problem if userspace manages to get more than a frame
ahead, leaving the atomic-commit worker blocked waiting on fences that
cannot be signaled because submit is blocked waiting for a fence
signalled from vblank (after the atomic commit which is blocked).

If we start having multiple fence ctxs for the gpu, submit_fence_sync()
would probably need to move outside of struct_mutex as well.
Signed-off-by: Rob Clark <robdclark@gmail.com>

In particular, attach() and unmap() need pm-runtime get/put to ensure
iommu clks are enabled.
Signed-off-by: Rob Clark <robdclark@gmail.com>

Significantly simplifies things.  Also iommu_unmap() can unmap an entire
iova range.

(If backporting to downstream kernel you might need to revert this.  Or
at least double check older iommu implementation.)
Signed-off-by: Rob Clark <robdclark@gmail.com>

We need to do this also in resume path when we need to re-hw_init().
Signed-off-by: Rob Clark <robdclark@gmail.com>

We need to use pm-runtime properly when IOMMU is using device_link() to
control it's own clocks.
Signed-off-by: Rob Clark <robdclark@gmail.com>

Each of the per-generation callbacks was doing this.  Lets just simplify
and move it into toplevel show() fxn.
Signed-off-by: Rob Clark <robdclark@gmail.com>

A few more things for 4.12:
- ttm and amdgpu support for non-contiguous vram CPU mappings
- lots of bug fixes and cleanups for vega10
- misc bug fixes and code cleanups

[airlied: fix do_div error on 32-bit arm, not sure it's 100% correct]

* 'drm-next-4.12' of git://people.freedesktop.org/~agd5f/linux: (58 commits)
  drm/amdgpu: use uintptr_t instead of unsigned long to store pointer
  drm/amdgpu: Avoid using signed integer to store pointer value
  drm/amdgpu:invoke new implemented AI MB func
  drm/amdgpu/vega10:timeout set to equal with VI
  drm/amdgpu:implement the reset MB func for vega10
  drm/amdgpu:fix typo for mxgpu_ai
  drm/amdgpu:no need to involv HDP in KIQ
  drm/amdgpu:add PSP block only load_type=PSP (v2)
  drm/amdgpu/smu9: update to latest driver interface
  drm/amd/amdgpu: cleanup gfx_v9_0_gpu_init()
  drm/amd/amdgpu: cleanup gfx_v9_0_rlc_reset()
  drm/amd/amdgpu: cleanup gfx_v9_0_rlc_start()
  drm/amd/amdgpu: simplify gfx_v9_0_cp_gfx_enable()
  drm/amd/amdgpu: cleanup gfx_v9_0_kiq_init_register()
  drm/amd/amdgpu: Drop gfx_v9_0_print_status()
  drm/amd/amdgpu: cleanup gfx_v9_0_set_gfx_eop_interrupt_state()
  drm/amd/amdgpu: cleanup gfx_v9_0_set_priv_reg_fault_state()
  drm/amd/amdgpu: cleanup gfx_v9_0_set_priv_inst_fault_state()
  drm/amd/amdgpu: cleanup gfx_v9_0_init_queue()
  drm/amdgpu: Move function amdgpu_has_atpx near other similar functions
  ...

Highlights:
- Cooling device support from Russell, to allow GPU throttling on system
thermal overload.
- Explicit fencing support from Philipp, implemented in a similar way to
drm/msm.

* 'etnaviv/next' of https://git.pengutronix.de/git/lst/linux:
  drm/etnaviv: submit support for out-fences
  drm/etnaviv: return GPU fence through the submit structure
  drm/etnaviv: submit support for in-fences
  drm/etnaviv: add etnaviv cooling device
  drm/etnaviv: switch to postclose
  drm/etnaviv: add lockdep assert to fence allocation

imx-drm module/dependency changes

- The PRE/PRG drivers added an unwanted DRM dependency to the ipu-v3 driver.
  Remove the dependency by conditionally disabling PRE/PRG support depending
  on CONFIG_DRM.
- Merge the imx-ipuv3-crtc module into the imxdrm module. There is no reason
  anymore for a separation between core drm driver and crtc/plane drivers,
  especially since commit eb8c8880 ("drm/imx: add deferred plane
  disabling"), which added a dependency on imx-ipuv3-crtc to the imxdrm
  module.

* tag 'imx-drm-next-2017-04-04' of git://git.pengutronix.de/git/pza/linux:
  drm/imx: merge imx-drm-core and ipuv3-crtc in one module
  gpu: ipu-v3: don't depend on DRM being enabled

A bit more for 4.12:
- GP10B support
- GP107 acceleration support

* 'linux-4.12' of git://github.com/skeggsb/linux: (23 commits)
  drm/nouveau/gpio: enable interrupts on cards with 32 gpio lines
  drm/nouveau/gr/gp107: initial support
  drm/nouveau/core: recognise GP10B chipset
  drm/nouveau/platform: support for probing GP10B
  drm/nouveau/platform: make VDD regulator optional
  drm/nouveau/gr: support for GP10B
  drm/nouveau/ibus: add GP10B support
  drm/nouveau/mc: add GP10B support
  drm/nouveau/fb: add GP10B support
  drm/nouveau/fifo: add GP10B support
  drm/nouveau/msgqueue: support for GP10B PMU firmware
  drm/nouveau/secboot: add GP10B support
  drm/nouveau/secboot/gm20b: specify MC base address as argument
  drm/nouveau/secboot: start LS firmware in post-run hook
  drm/nouveau/secboot: let LS post_run hooks return error
  drm/nouveau/secboot: pass instance to LS firmware loaders
  drm/nouveau/secboot: allow to boot multiple falcons
  drm/nouveau/imem/gk20a: Turn instmem lock into mutex
  drm/nouveau: initial support (display-only) for GP107
  drm/nouveau/kms/nv50: fix double dma_fence_put() when destroying plane state
  ...

Signed-off-by: Alex Xie <AlexBin.Xie@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Alex Xie <AlexBin.Xie@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Implement the sr-iov mailbox for soc15 asics.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

they are lack in the bringup stage, we need them for GPU reset
feature.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

1,KIQ won't touch VRAM so no need to involv HDP flush/invalidate at all.
2,According to CP hw designer KIQ better not use any PM4 package lead to wait behave.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

SRIOV currently only can load ucode directly, and PSP
block is not supported by VF temporarily.

will remove this restrict and use PSP load all ucode
even for SRIOV later

v2: squash in check against module parameter
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>