Like many i2c-hid touchscreen controllers, the Elan eKTH6915 has a
reset GPIO hooked up to it. According to the datasheet, the way we're
supposed to turn the touchscreen on is:

1. Turn on the 3.3V supply.
2. Turn on the IO supply. It's OK if this is hardwired to the 3.3V
   supply, but if it's not then it must be turned on _after_ the 3.3V
   supply.
3. Wait >= 1 ms.
4. Deassert the reset GPIO (reset GPIO is active low, so there would
   be a leakage path if this was deasserted _before_ the IO supply).
5. Wait 300 ms.

Much of the above can be handled by the generic i2c-hid-of driver, but
the "reset" GPIO is not supported by that driver. Thus we'll do the
same as we did for Goodix and add a new tiny driver that uses the
i2c-hid core.

NOTE: support for this new touchscreen could theorically fit into the
Goodix driver. I've made it a separate driver because the Elan driver
supports _two_ regulators and it's unclear exactly how that would fit
in with commit 18eeef46 ("HID: i2c-hid: goodix: Tie the reset line
to true state of the regulator").
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Like many i2c-hid touchscreen controllers, the Elan eKTH6915
controller has a reset gpio. For the Goodix GT7375P touchscreen the
decision was to add a new binding rather than trying to add a new GPIO
to the existing i2c-hid binding. We'll follow the lead and do it here,
too.

SIDE NOTE: the Elan eKTH6915 is a touchscreen _controller_ that's
included as a part on some touchscreens. The reset line isn't truly
necessary for the functioning of the touchscreen, so it's possible
that some designs won't have it hooked up and will just guarantee the
power sequencing requirements with RLC circuits. Thus, we'll mark the
reset gpio as optional.

Note that if the reset GPIO isn't used there's actually no true need
to use the "elan,ekth6915" compatible instead of the "hid-over-i2c" on
Linux. However:
- Officially using just "hid-over-i2c" for this device violates the
  existing "hid-over-i2c" bindings. The bindings say that you're not
  supposed to use "post-power-on-delay-ms" without specifying a more
  specific compatible. Currently the Linux driver doesn't enforce
  this, but it violates the bindings to just use
  "hid-over-i2c". ...and if you're going to add a more specific
  compatible anyway, might as well do it right.
- Using this compatible means we don't need to specify
  "hid-descr-addr" since it's inferred from the compatible.
- Using this compatible means that the regulator names match the names
  on the Elan datasheet (vcc33 / vccio) vs the generic hid-over-i2c
  (vdd / vddl).
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Pull HID updates from Jiri Kosina:

 - support for pens with 3 buttons with Wacom driver (Joshua Dickens)

 - support for HID_DG_SCANTIME to report the timestamp for pen and touch
   events in Wacom driver (Joshua Dickens)

 - support for sensor discovery in amd-sfh driver (Basavaraj Natikar)

 - support for wider variety of Huion tablets ported from DIGImend
   project (José Expósito, Nikolai Kondrashov)

 - new device IDs and other assorted small code cleanups

* tag 'for-linus-2022052401' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (44 commits)
  HID: apple: Properly handle function keys on Keychron keyboards
  HID: uclogic: Switch to Digitizer usage for styluses
  HID: uclogic: Add pen support for XP-PEN Star 06
  HID: uclogic: Differentiate touch ring and touch strip
  HID: uclogic: Always shift touch reports to zero
  HID: uclogic: Do not focus on touch ring only
  HID: uclogic: Return raw parameters from v2 pen init
  HID: uclogic: Move param printing to a function
  HID: core: Display "SENSOR HUB" for sensor hub bus string in hid_info
  HID: amd_sfh: Move bus declaration outside of amd-sfh
  HID: amd_sfh: Add physical location to HID device
  HID: amd_sfh: Modify the hid name
  HID: amd_sfh: Modify the bus name
  HID: amd_sfh: Add sensor name by index for debug info
  HID: amd_sfh: Add support for sensor discovery
  HID: bigben: fix slab-out-of-bounds Write in bigben_probe
  Hid: wacom: Fix kernel test robot warning
  HID: uclogic: Disable pen usage for Huion keyboard interfaces
  HID: uclogic: Support disabling pen usage
  HID: uclogic: Pass keyboard reports as is
  ...

Pull spi updates from Mark Brown:
 "This is quite a quiet release but some new drivers mean that the
  diffstat is fairly large. The new drivers include the aspeed driver
  which is migrated from MTD as part of the ongoing move of controllers
  with specialised support for SPI flashes into the SPI subsystem.

   - Support for devices which flip CPHA during recieve only transfers
     (eg, if MOSI and MISO have inverted polarity).

   - Overhaul of the i.MX driver, including the addition of PIO support
     for better performance on small transfers.

   - Migration of the Aspeed driver from MTD.

   - Support for Aspeed AST2400, Ingenic JZ4775 and X1/2000 and MediaTek
     IPM and SFI"

* tag 'spi-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (84 commits)
  spi: spi-au1550: replace ternary operator with min()
  mtd: spi-nor: aspeed: set the decoding size to at least 2MB for AST2600
  spi: aspeed: Calibrate read timings
  spi: aspeed: Add support for the AST2400 SPI controller
  spi: aspeed: Workaround AST2500 limitations
  spi: aspeed: Adjust direct mapping to device size
  spi: aspeed: Add support for direct mapping
  spi: spi-mem: Convert Aspeed SMC driver to spi-mem
  spi: Convert the Aspeed SMC controllers device tree binding
  spi: spi-cadence: Update ISR status variable type to irqreturn_t
  spi: Doc fix - Describe add_lock and dma_map_dev in spi_controller
  spi: cadence-quadspi: Handle spi_unregister_master() in remove()
  spi: stm32-qspi: Remove SR_BUSY bit check before sending command
  spi: stm32-qspi: Always check SR_TCF flags in stm32_qspi_wait_cmd()
  spi: stm32-qspi: Fix wait_cmd timeout in APM mode
  spi: cadence-quadspi: remove unnecessary (void *) casts
  spi: cadence-quadspi: Add missing blank line in cqspi_request_mmap_dma()
  spi: spi-imx: mx51_ecspi_prepare_message(): skip writing MX51_ECSPI_CONFIG register if unchanged
  spi: spi-imx: add PIO polling support
  spi: spi-imx: replace struct spi_imx_data::bitbang by pointer to struct spi_controller
  ...

Pull regulator updates from Mark Brown:
 "This is mostly a drivers update including a couple of new drivers but
  we do have some fixes and improvements to the core as well.

   - Make sure we don't log spuriously about uncontrollable regulators.

   - Don't use delays when we should use sleeps for regulators with
     larger ramp times.

   - Support for MediaTek MT6358 and MT6366, Richtek RT5759 and Silicon
     Mitus SM5703"

* tag 'regulator-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (36 commits)
  regulator: scmi: Fix refcount leak in scmi_regulator_probe
  regulator: pfuze100: Fix refcount leak in pfuze_parse_regulators_dt
  regulator: qcom_smd: Fix up PM8950 regulator configuration
  regulator: core: Fix enable_count imbalance with EXCLUSIVE_GET
  regulator: core: Add error flags to sysfs attributes
  regulator: dt-bindings: qcom,rpmh: document vdd-l7-bob-supply on PMR735A
  regulator: dt-bindings: qcom,rpmh: document supplies per variant
  regulator: dt-bindings: qcom,rpmh: update maintainers
  regulator: mt6315: Enforce regulator-compatible, not name
  regulator: pca9450: Enable DVS control via PMIC_STBY_REQ
  regulator: pca9450: Make warm reset on WDOG_B assertion
  regulator: Add property for WDOG_B warm reset
  regulator: pca9450: Make I2C Level Translator configurable
  regulator: Add property for I2C level shifter
  regulator: sm5703: Correct reference to the common regulator schema
  regulator: sm5703-regulator: Add regulators support for SM5703 MFD
  dt-bindings: regulator: Add bindings for Silicon Mitus SM5703 regulators
  regulator: richtek,rt4801: parse GPIOs per regulator
  regulator: dt-bindings: richtek,rt4801: use existing ena_gpiod feature
  regulator: core: Sleep (not delay) in set_voltage()
  ...

Pull regmap updates from Mark Brown:
 "The main change here is Marek's addition of bulk read/write callbacks
  for individual regmaps, we've supported single register operations for
  a while but there's enough hardware out there which can use bulk
  equivalents to make it worthwhile"

* tag 'regmap-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: Add missing map->bus check
  regmap: Add bulk read/write callbacks into regmap_config
  regmap: cache: set max_register with reg_stride
  regmap: Constify static regmap_bus structs

Pull MMC updates from Ulf Hansson:
 "MMC core:

   - Support zero-out using TRIM for eMMC

   - Allow to override the busy-timeout for the ioctl-cmds

  MMC host:

   - Continued the conversion of DT bindings into the JSON schema

   - jz4740: Apply DMA engine limits to maximum segment size

   - mmci_stm32: Use a buffer for unaligned DMA requests

   - mmc_spi: Enabled high-speed modes via parsing of DT

   - omap: Make clock management to be compliant with CCF

   - renesas_sdhi:
      - Support eMMC HS400 mode for R-Car V3H ES2.0
      - Don't allow support for eMMC HS400 for R-Car V3M/D3

   - sdhci_am654: Fix problem when SD card slot lacks the card detect
     line

   - sdhci-esdhc-imx: Add support for the imx8dxl variant

   - sdhci-brcmstb: Enable support for clock gating to save power

   - sdhci-msm:
      - Add support for the sdx65 variant
      - Add support for the sm8150 variant

   - sdhci-of-dwcmshc: Add support for the Rockchip rk3588 variant

   - sdhci-pci-gli: Add workaround to allow GL9755 to enter ASPM L1.2"

* tag 'mmc-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (52 commits)
  mmc: sdhci-of-arasan: Add NULL check for data field
  mmc: core: Support zeroout using TRIM for eMMC
  mmc: sdhci-brcmstb: Fix compiler warning
  mmc: sdhci-msm: Add compatible string check for sdx65
  dt-bindings: mmc: sdhci-msm: Document the SDX65 compatible
  mmc: sdhci-msm: Add compatible string check for sm8150
  dt-bindings: mmc: sdhci-msm: Add compatible string for sm8150
  mmc: sdhci-msm: Add SoC specific compatibles
  dt-bindings: mmc: sdhci-msm: Convert bindings to yaml
  dt-bindings: mmc: brcm,sdhci-brcmstb: cleanup example
  dt-bindings: mmc: brcm,sdhci-brcmstb: correct number of reg entries
  mmc: sdhci-brcmstb: Enable Clock Gating to save power
  mmc: sdhci-brcmstb: Re-organize flags
  mmc: mmci: Remove custom ios handler
  mmc: atmel-mci: Simplify if(chan) and if(!chan)
  mmc: core: use kobj_to_dev()
  dt-bindings: mmc: sdhci-of-dwcmhsc: Add rk3588
  mmc: core: Add CIDs for cards to the entropy pool
  mmc: core: Allows to override the timeout value for ioctl() path
  mmc: sdhci-omap: Use of_device_get_match_data() helper
  ...

Pull IPMI update from Corey Minyard:
 "Add limits on the number of users and messages, plus sysfs interfaces
  to control those limits.

  Other than that, little cleanups, use dev_xxx() insted of pr_xxx(),
  create initializers for structures, fix a refcount leak, etc"

* tag 'for-linus-4.19-1' of https://github.com/cminyard/linux-ipmi:
  ipmi:ipmb: Fix refcount leak in ipmi_ipmb_probe
  ipmi: remove unnecessary type castings
  ipmi: Make two logs unique
  ipmi:si: Convert pr_debug() to dev_dbg()
  ipmi: Convert pr_debug() to dev_dbg()
  ipmi: Fix pr_fmt to avoid compilation issues
  ipmi: Add an intializer for ipmi_recv_msg struct
  ipmi: Add an intializer for ipmi_smi_msg struct
  ipmi:ssif: Check for NULL msg when handling events and messages
  ipmi: use simple i2c probe function
  ipmi: Add a sysfs count of total outstanding messages for an interface
  ipmi: Add a sysfs interface to view the number of users
  ipmi: Limit the number of message a user may have outstanding
  ipmi: Add a limit on the number of users that may use IPMI

Pull mtd updates from Miquel Raynal:
 "MTD core changes:
   - Call of_platform_populate() for MTD partitions
   - Check devicetree alias for index
   - mtdoops:
      - Add a timestamp to the mtdoops header.
      - Create a header structure for the saved mtdoops.
      - Fix the size of the header read buffer.
   - mtdblock: Warn if opened on NAND
   - Bindings:
      - reserved-memory: Support MTD/block device
      - jedec,spi-nor: remove unneeded properties
      - Extend fixed-partitions binding
      - Add Sercomm (Suzhou) Corporation vendor prefix

  MTD driver changes:
   - st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
   - phram:
      - Allow cached mappings
      - Allow probing via reserved-memory
   - maps: ixp4xx: Drop driver
   - bcm47xxpart: Print correct offset on read error

  CFI driver changes:
   - Rename chip_ready variables
   - Add S29GL064N ID definition
   - Use chip_ready() for write on S29GL064N
   - Move and rename chip_check/chip_ready/chip_good_for_write

  NAND core changes:
   - Print offset instead of page number for bad blocks

  Raw NAND controller drivers:
   - Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
   - CS553X: simplify the return expression of cs553x_write_ctrl_byte()
   - Davinci: Remove redundant unsigned comparison to zero
   - Denali: Use managed device resources
   - GPMI:
      - Add large oob bch setting support
      - Rename the variable ecc_chunk_size
      - Uninline the gpmi_check_ecc function
      - Add strict ecc strength check
      - Refactor BCH geometry settings function
   - Intel: Fix possible null-ptr-deref in ebu_nand_probe()
   - MPC5121: Check before clk_disable_unprepare() not needed
   - Mtk:
      - MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
      - Also parse the default nand-ecc-engine property if available
      - Make mtk_ecc.c a separated module
   - OMAP ELM:
      - Convert the bindings to yaml
      - Describe the bindings for AM64 ELM
      - Add support for its compatible
   - Renesas: Use runtime PM instead of the raw clock API and update the
     bindings accordingly
   - Rockchip: Check before clk_disable_unprepare() not needed
   - TMIO: Check return value after calling platform_get_resource()

  Raw NAND chip driver:
   - Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00

  SPI-NAND chip drivers:
   - Gigadevice:
      - Add support for:
         - GD5FxGM7xExxG
         - GD5F{2,4}GQ5xExxG
         - GD5F1GQ5RExxG
         - GD5FxGQ4xExxG
      - Fix Quad IO for GD5F1GQ5UExxG
   - XTX: Add support for XT26G0xA

  SPI NOR core changes:
   - Read back written SR value to make sure the write was done
     correctly.
   - Introduce a common function for Read ID that manufacturer drivers
     can use to verify the Octal DTR switch worked correctly.
   - Add helpers for read/write any register commands so manufacturer
     drivers don't open code it every time.
   - Clarify rdsr dummy cycles documentation.
   - Add debugfs entry to expose internal flash parameters and state.

  SPI NOR manufacturer drivers changes:
   - Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
   - Move spi_nor_write_ear() to Winbond module since only Winbond
     flashes use it.
   - Rework Micron and Cypress Octal DTR enable methods to improve
     readability.
   - Use the common Read ID function to verify switch to Octal DTR mode
     for Micron and Cypress flashes.
   - Skip polling status on volatile register writes for Micron and
     Cypress flashes since the operation is instant"

* tag 'mtd/for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (68 commits)
  mtd: st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
  dt-bindings: mtd: partitions: Extend fixed-partitions binding
  dt-bindings: Add Sercomm (Suzhou) Corporation vendor prefix
  mtd: phram: Allow cached mappings
  mtd: call of_platform_populate() for MTD partitions
  mtd: rawnand: renesas: Use runtime PM instead of the raw clock API
  dt-bindings: mtd: renesas: Fix the NAND controller description
  mtd: rawnand: mpc5121: Check before clk_disable_unprepare() not needed
  mtd: rawnand: rockchip: Check before clk_disable_unprepare() not needed
  mtd: nand: MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
  mtd: rawnand: cs553x: simplify the return expression of cs553x_write_ctrl_byte()
  mtd: rawnand: kioxia: Add support for TH58NVG3S0HBAI4
  mtd: spi-nor: debugfs: fix format specifier
  mtd: spi-nor: support eon en25qh256a variant
  mtd: spi-nor: winbond: add support for W25Q512NW-IM
  mtd: spi-nor: expose internal parameters via debugfs
  mtd: spi-nor: export spi_nor_hwcaps_pp2cmd()
  mtd: spi-nor: move spi_nor_write_ear() to winbond module
  mtd: spi-nor: amend the rdsr dummy cycles documentation
  mtd: cfi_cmdset_0002: Rename chip_ready variables
  ...

Merge tag 'hwmon-for-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:
 "New drivers:

   - Driver for the Microchip LAN966x SoC

   - PMBus driver for Infineon Digital Multi-phase xdp152 family
     controllers

  Chip support added to existing drivers:

   - asus-ec-sensors:
      - Support for ROG STRIX X570-E GAMING WIFI II, PRIME X470-PRO, and
        ProArt X570 Creator WIFI
      - External temperature sensor support for ASUS WS X570-ACE

   - nct6775:
      - Support for I2C driver
      - Support for ASUS PRO H410T / PRIME H410M-R /
        ROG X570-E GAMING WIFI II

   - lm75:
      - Support for - Atmel AT30TS74

   - pmbus/max16601:
      - Support for MAX16602

   - aquacomputer_d5next:
      - Support for Aquacomputer Farbwerk
      - Support for Aquacomputer Octo

   - jc42:
      - Support for S-34TS04A

  Kernel API changes / clarifications:

   - The chip parameter of with_info API is now mandatory

   - New hwmon_device_register_for_thermal API call for use by the
     thermal subsystem

  Improvements:

   - PMBus and JC42 drivers now register with thermal subsystem

   - PMBus drivers now support get_voltage/set_voltage power operations

   - The adt7475 driver now supports pin configuration

   - The lm90 driver now supports setting extended range temperatures
     configuration with a devicetree property

   - The dell-smm driver now registers as cooling device

   - The OCC driver delays hwmon registration until requested by
     userspace

  ... and various other minor fixes and improvements"

* tag 'hwmon-for-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (71 commits)
  hwmon: (aquacomputer_d5next) Fix an error handling path in aqc_probe()
  hwmon: (sl28cpld) Fix typo in comment
  hwmon: (pmbus) Check PEC support before reading other registers
  hwmon: (dimmtemp) Fix bitmap handling
  hwmon: (lm90) enable extended range according to DTS node
  dt-bindings: hwmon: lm90: add ti,extended-range-enable property
  dt-bindings: hwmon: lm90: add missing ti,tmp461
  hwmon: (ibmaem) Directly use ida_alloc()/free()
  hwmon: Directly use ida_alloc()/free()
  hwmon: (asus-ec-sensors) fix Formula VIII definition
  dt-bindings: trivial-devices: Add xdp152
  hwmon: (sl28cpld-hwmon) Use HWMON_CHANNEL_INFO macro
  hwmon: (pwm-fan) Use HWMON_CHANNEL_INFO macro
  hwmon: (peci/dimmtemp) Use HWMON_CHANNEL_INFO macro
  hwmon: (peci/cputemp) Use HWMON_CHANNEL_INFO macro
  hwmon: (mr75203) Use HWMON_CHANNEL_INFO macro
  hwmon: (ltc2992) Use HWMON_CHANNEL_INFO macro
  hwmon: (as370-hwmon) Use HWMON_CHANNEL_INFO macro
  hwmon: Make chip parameter for with_info API mandatory
  thermal/drivers/thermal_hwmon: Use hwmon_device_register_for_thermal()
  ...

Pull IMA updates from Mimi Zohar:
 "New is IMA support for including fs-verity file digests and signatures
  in the IMA measurement list as well as verifying the fs-verity file
  digest based signatures, both based on policy.

  In addition, are two bug fixes:

   - avoid reading UEFI variables, which cause a page fault, on Apple
     Macs with T2 chips.

   - remove the original "ima" template Kconfig option to address a boot
     command line ordering issue.

  The rest is a mixture of code/documentation cleanup"

* tag 'integrity-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
  integrity: Fix sparse warnings in keyring_handler
  evm: Clean up some variables
  evm: Return INTEGRITY_PASS for enum integrity_status value '0'
  efi: Do not import certificates from UEFI Secure Boot for T2 Macs
  fsverity: update the documentation
  ima: support fs-verity file digest based version 3 signatures
  ima: permit fsverity's file digests in the IMA measurement list
  ima: define a new template field named 'd-ngv2' and templates
  fs-verity: define a function to return the integrity protected file digest
  ima: use IMA default hash algorithm for integrity violations
  ima: fix 'd-ng' comments and documentation
  ima: remove the IMA_TEMPLATE Kconfig option
  ima: remove redundant initialization of pointer 'file'.

Merge tag 'tpmdd-next-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd

Pull tpm updates from Jarkko Sakkinen:

 - Tightened validation of key hashes for SYSTEM_BLACKLIST_HASH_LIST. An
   invalid hash format causes a compilation error. Previously, they got
   included to the kernel binary but were silently ignored at run-time.

 - Allow root user to append new hashes to the blacklist keyring.

 - Trusted keys backed with Cryptographic Acceleration and Assurance
   Module (CAAM), which part of some of the new NXP's SoC's. Now there
   is total three hardware backends for trusted keys: TPM, ARM TEE and
   CAAM.

 - A scattered set of fixes and small improvements for the TPM driver.

* tag 'tpmdd-next-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
  MAINTAINERS: add KEYS-TRUSTED-CAAM
  doc: trusted-encrypted: describe new CAAM trust source
  KEYS: trusted: Introduce support for NXP CAAM-based trusted keys
  crypto: caam - add in-kernel interface for blob generator
  crypto: caam - determine whether CAAM supports blob encap/decap
  KEYS: trusted: allow use of kernel RNG for key material
  KEYS: trusted: allow use of TEE as backend without TCG_TPM support
  tpm: Add field upgrade mode support for Infineon TPM2 modules
  tpm: Fix buffer access in tpm2_get_tpm_pt()
  char: tpm: cr50_i2c: Suppress duplicated error message in .remove()
  tpm: cr50: Add new device/vendor ID 0x504a6666
  tpm: Remove read16/read32/write32 calls from tpm_tis_phy_ops
  tpm: ibmvtpm: Correct the return value in tpm_ibmvtpm_probe()
  tpm/tpm_ftpm_tee: Return true/false (not 1/0) from bool functions
  certs: Explain the rationale to call panic()
  certs: Allow root user to append signed hashes to the blacklist keyring
  certs: Check that builtin blacklist hashes are valid
  certs: Make blacklist_vet_description() more strict
  certs: Factor out the blacklist hash creation
  tools/certs: Add print-cert-tbs-hash.sh

Pull smack update from Casey Schaufler:
 "A single change to remove a pointless assignment"

* tag 'Smack-for-5.19' of https://github.com/cschaufler/smack-next:
  smack: Remove redundant assignments

Pull Landlock updates from Mickaël Salaün:

 - improve the path_rename LSM hook implementations for RENAME_EXCHANGE;

 - fix a too-restrictive filesystem control for a rare corner case;

 - set the nested sandbox limitation to 16 layers;

 - add a new LANDLOCK_ACCESS_FS_REFER access right to properly handle
   file reparenting (i.e. full rename and link support);

 - add new tests and documentation;

 - format code with clang-format to make it easier to maintain and
   contribute.

* tag 'landlock-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux: (30 commits)
  landlock: Explain how to support Landlock
  landlock: Add design choices documentation for filesystem access rights
  landlock: Document good practices about filesystem policies
  landlock: Document LANDLOCK_ACCESS_FS_REFER and ABI versioning
  samples/landlock: Add support for file reparenting
  selftests/landlock: Add 11 new test suites dedicated to file reparenting
  landlock: Add support for file reparenting with LANDLOCK_ACCESS_FS_REFER
  LSM: Remove double path_rename hook calls for RENAME_EXCHANGE
  landlock: Move filesystem helpers and add a new one
  landlock: Fix same-layer rule unions
  landlock: Create find_rule() from unmask_layers()
  landlock: Reduce the maximum number of layers to 16
  landlock: Define access_mask_t to enforce a consistent access mask size
  selftests/landlock: Test landlock_create_ruleset(2) argument check ordering
  landlock: Change landlock_restrict_self(2) check ordering
  landlock: Change landlock_add_rule(2) argument check ordering
  selftests/landlock: Add tests for O_PATH
  selftests/landlock: Fully test file rename with "remove" access
  selftests/landlock: Extend access right tests to directories
  selftests/landlock: Add tests for unknown access rights
  ...

Pull selinux updates from Paul Moore:
 "We've got twelve patches queued for v5.19, with most being fairly
  minor. The highlights are below:

   - The checkreqprot and runtime disable knobs have been deprecated for
     some time with no active users that we can find. In an effort to
     move things along we are adding a pause when the knobs are used to
     help make the deprecation more noticeable in case anyone is still
     using these hacks in the shadows.

   - We've added the anonymous inode class name to the AVC audit records
     when anonymous inodes are involved. This should make writing policy
     easier when anonymous inodes are involved.

   - More constification work. This is fairly straightforward and the
     source of most of the diffstat.

   - The usual minor cleanups: remove unnecessary assignments, assorted
     style/checkpatch fixes, kdoc fixes, macro while-loop
     encapsulations, #include tweaks, etc"

* tag 'selinux-pr-20220523' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
  security: declare member holding string literal const
  selinux: log anon inode class name
  selinux: declare data arrays const
  selinux: fix indentation level of mls_ops block
  selinux: include necessary headers in headers
  selinux: avoid extra semicolon
  selinux: update parameter documentation
  selinux: resolve checkpatch errors
  selinux: don't sleep when CONFIG_SECURITY_SELINUX_CHECKREQPROT_VALUE is true
  selinux: checkreqprot is deprecated, add some ssleep() discomfort
  selinux: runtime disable is deprecated, add some ssleep() discomfort
  selinux: Remove redundant assignments

Pull execve updates from Kees Cook:

 - Fix binfmt_flat GOT handling for riscv (Niklas Cassel)

 - Remove unused/broken binfmt_flat shared library and coredump code
   (Eric W. Biederman)

* tag 'execve-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  binfmt_flat: Remove shared library support
  binfmt_flat: Drop vestiges of coredump support
  binfmt_flat: do not stop relocating GOT entries prematurely on riscv

Pull seccomp updates from Kees Cook:

 - Rework USER_NOTIF notification ordering and kill logic (Sargun
   Dhillon)

 - Improved PTRACE_O_SUSPEND_SECCOMP selftest (Jann Horn)

 - Gracefully handle failed unshare() in selftests (Yang Guang)

 - Spelling fix (Colin Ian King)

* tag 'seccomp-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  selftests/seccomp: Fix spelling mistake "Coud" -> "Could"
  selftests/seccomp: Add test for wait killable notifier
  selftests/seccomp: Refactor get_proc_stat to split out file reading code
  seccomp: Add wait_killable semantic to seccomp user notifier
  selftests/seccomp: Ensure that notifications come in FIFO order
  seccomp: Use FIFO semantics to order notifications
  selftests/seccomp: Add SKIP for failed unshare()
  selftests/seccomp: Test PTRACE_O_SUSPEND_SECCOMP without CAP_SYS_ADMIN

Pull kernel hardening updates from Kees Cook:

 - usercopy hardening expanded to check other allocation types (Matthew
   Wilcox, Yuanzheng Song)

 - arm64 stackleak behavioral improvements (Mark Rutland)

 - arm64 CFI code gen improvement (Sami Tolvanen)

 - LoadPin LSM block dev API adjustment (Christoph Hellwig)

 - Clang randstruct support (Bill Wendling, Kees Cook)

* tag 'kernel-hardening-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (34 commits)
  loadpin: stop using bdevname
  mm: usercopy: move the virt_addr_valid() below the is_vmalloc_addr()
  gcc-plugins: randstruct: Remove cast exception handling
  af_unix: Silence randstruct GCC plugin warning
  niu: Silence randstruct warnings
  big_keys: Use struct for internal payload
  gcc-plugins: Change all version strings match kernel
  randomize_kstack: Improve docs on requirements/rationale
  lkdtm/stackleak: fix CONFIG_GCC_PLUGIN_STACKLEAK=n
  arm64: entry: use stackleak_erase_on_task_stack()
  stackleak: add on/off stack variants
  lkdtm/stackleak: check stack boundaries
  lkdtm/stackleak: prevent unexpected stack usage
  lkdtm/stackleak: rework boundary management
  lkdtm/stackleak: avoid spurious failure
  stackleak: rework poison scanning
  stackleak: rework stack high bound handling
  stackleak: clarify variable names
  stackleak: rework stack low bound handling
  stackleak: remove redundant check
  ...

Pull fsverity updates from Eric Biggers:
 "A couple small cleanups for fs/verity/"

* tag 'fsverity-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt:
  fs-verity: Use struct_size() helper in enable_verity()
  fs-verity: remove unused parameter desc_size in fsverity_create_info()

Pull fscrypt updates from Eric Biggers:
 "Some cleanups for fs/crypto/:

   - Split up the misleadingly-named FS_CRYPTO_BLOCK_SIZE constant.

   - Consistently report the encryption implementation that is being
     used.

   - Add helper functions for the test_dummy_encryption mount option
     that work properly with the new mount API. ext4 and f2fs will use
     these"

* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt:
  fscrypt: add new helper functions for test_dummy_encryption
  fscrypt: factor out fscrypt_policy_to_key_spec()
  fscrypt: log when starting to use inline encryption
  fscrypt: split up FS_CRYPTO_BLOCK_SIZE

Pull random number generator updates from Jason Donenfeld:
 "These updates continue to refine the work began in 5.17 and 5.18 of
  modernizing the RNG's crypto and streamlining and documenting its
  code.

  New for 5.19, the updates aim to improve entropy collection methods
  and make some initial decisions regarding the "premature next" problem
  and our threat model. The cloc utility now reports that random.c is
  931 lines of code and 466 lines of comments, not that basic metrics
  like that mean all that much, but at the very least it tells you that
  this is very much a manageable driver now.

  Here's a summary of the various updates:

   - The random_get_entropy() function now always returns something at
     least minimally useful. This is the primary entropy source in most
     collectors, which in the best case expands to something like RDTSC,
     but prior to this change, in the worst case it would just return 0,
     contributing nothing. For 5.19, additional architectures are wired
     up, and architectures that are entirely missing a cycle counter now
     have a generic fallback path, which uses the highest resolution
     clock available from the timekeeping subsystem.

     Some of those clocks can actually be quite good, despite the CPU
     not having a cycle counter of its own, and going off-core for a
     stamp is generally thought to increase jitter, something positive
     from the perspective of entropy gathering. Done very early on in
     the development cycle, this has been sitting in next getting some
     testing for a while now and has relevant acks from the archs, so it
     should be pretty well tested and fine, but is nonetheless the thing
     I'll be keeping my eye on most closely.

   - Of particular note with the random_get_entropy() improvements is
     MIPS, which, on CPUs that lack the c0 count register, will now
     combine the high-speed but short-cycle c0 random register with the
     lower-speed but long-cycle generic fallback path.

   - With random_get_entropy() now always returning something useful,
     the interrupt handler now collects entropy in a consistent
     construction.

   - Rather than comparing two samples of random_get_entropy() for the
     jitter dance, the algorithm now tests many samples, and uses the
     amount of differing ones to determine whether or not jitter entropy
     is usable and how laborious it must be. The problem with comparing
     only two samples was that if the cycle counter was extremely slow,
     but just so happened to be on the cusp of a change, the slowness
     wouldn't be detected. Taking many samples fixes that to some
     degree.

     This, combined with the other improvements to random_get_entropy(),
     should make future unification of /dev/random and /dev/urandom
     maybe more possible. At the very least, were we to attempt it again
     today (we're not), it wouldn't break any of Guenter's test rigs
     that broke when we tried it with 5.18. So, not today, but perhaps
     down the road, that's something we can revisit.

   - We attempt to reseed the RNG immediately upon waking up from system
     suspend or hibernation, making use of the various timestamps about
     suspend time and such available, as well as the usual inputs such
     as RDRAND when available.

   - Batched randomness now falls back to ordinary randomness before the
     RNG is initialized. This provides more consistent guarantees to the
     types of random numbers being returned by the various accessors.

   - The "pre-init injection" code is now gone for good. I suspect you
     in particular will be happy to read that, as I recall you
     expressing your distaste for it a few months ago. Instead, to avoid
     a "premature first" issue, while still allowing for maximal amount
     of entropy availability during system boot, the first 128 bits of
     estimated entropy are used immediately as it arrives, with the next
     128 bits being buffered. And, as before, after the RNG has been
     fully initialized, it winds up reseeding anyway a few seconds later
     in most cases. This resulted in a pretty big simplification of the
     initialization code and let us remove various ad-hoc mechanisms
     like the ugly crng_pre_init_inject().

   - The RNG no longer pretends to handle the "premature next" security
     model, something that various academics and other RNG designs have
     tried to care about in the past. After an interesting mailing list
     thread, these issues are thought to be a) mainly academic and not
     practical at all, and b) actively harming the real security of the
     RNG by delaying new entropy additions after a potential compromise,
     making a potentially bad situation even worse. As well, in the
     first place, our RNG never even properly handled the premature next
     issue, so removing an incomplete solution to a fake problem was
     particularly nice.

     This allowed for numerous other simplifications in the code, which
     is a lot cleaner as a consequence. If you didn't see it before,
     https://lore.kernel.org/lkml/YmlMGx6+uigkGiZ0@zx2c4.com/ may be a
     thread worth skimming through.

   - While the interrupt handler received a separate code path years ago
     that avoids locks by using per-cpu data structures and a faster
     mixing algorithm, in order to reduce interrupt latency, input and
     disk events that are triggered in hardirq handlers were still
     hitting locks and more expensive algorithms. Those are now
     redirected to use the faster per-cpu data structures.

   - Rather than having the fake-crypto almost-siphash-based random32
     implementation be used right and left, and in many places where
     cryptographically secure randomness is desirable, the batched
     entropy code is now fast enough to replace that.

   - As usual, numerous code quality and documentation cleanups. For
     example, the initialization state machine now uses enum symbolic
     constants instead of just hard coding numbers everywhere.

   - Since the RNG initializes once, and then is always initialized
     thereafter, a pretty heavy amount of code used during that
     initialization is never used again. It is now completely cordoned
     off using static branches and it winds up in the .text.unlikely
     section so that it doesn't reduce cache compactness after the RNG
     is ready.

   - A variety of functions meant for waiting on the RNG to be
     initialized were only used by vsprintf, and in not a particularly
     optimal way. Replacing that usage with a more ordinary setup made
     it possible to remove those functions.

   - A cleanup of how we warn userspace about the use of uninitialized
     /dev/urandom and uninitialized get_random_bytes() usage.
     Interestingly, with the change you merged for 5.18 that attempts to
     use jitter (but does not block if it can't), the majority of users
     should never see those warnings for /dev/urandom at all now, and
     the one for in-kernel usage is mainly a debug thing.

   - The file_operations struct for /dev/[u]random now implements
     .read_iter and .write_iter instead of .read and .write, allowing it
     to also implement .splice_read and .splice_write, which makes
     splice(2) work again after it was broken here (and in many other
     places in the tree) during the set_fs() removal. This was a bit of
     a last minute arrival from Jens that hasn't had as much time to
     bake, so I'll be keeping my eye on this as well, but it seems
     fairly ordinary. Unfortunately, read_iter() is around 3% slower
     than read() in my tests, which I'm not thrilled about. But Jens and
     Al, spurred by this observation, seem to be making progress in
     removing the bottlenecks on the iter paths in the VFS layer in
     general, which should remove the performance gap for all drivers.

   - Assorted other bug fixes, cleanups, and optimizations.

   - A small SipHash cleanup"

* tag 'random-5.19-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random: (49 commits)
  random: check for signals after page of pool writes
  random: wire up fops->splice_{read,write}_iter()
  random: convert to using fops->write_iter()
  random: convert to using fops->read_iter()
  random: unify batched entropy implementations
  random: move randomize_page() into mm where it belongs
  random: remove mostly unused async readiness notifier
  random: remove get_random_bytes_arch() and add rng_has_arch_random()
  random: move initialization functions out of hot pages
  random: make consistent use of buf and len
  random: use proper return types on get_random_{int,long}_wait()
  random: remove extern from functions in header
  random: use static branch for crng_ready()
  random: credit architectural init the exact amount
  random: handle latent entropy and command line from random_init()
  random: use proper jiffies comparison macro
  random: remove ratelimiting for in-kernel unseeded randomness
  random: move initialization out of reseeding hot path
  random: avoid initializing twice in credit race
  random: use symbolic constants for crng_init states
  ...

KGDB and KDB allow read and write access to kernel memory, and thus
should be restricted during lockdown.  An attacker with access to a
serial port (for example, via a hypervisor console, which some cloud
vendors provide over the network) could trigger the debugger so it is
important that the debugger respect the lockdown mode when/if it is
triggered.

Fix this by integrating lockdown into kdb's existing permissions
mechanism.  Unfortunately kgdb does not have any permissions mechanism
(although it certainly could be added later) so, for now, kgdb is simply
and brutally disabled by immediately exiting the gdb stub without taking
any action.

For lockdowns established early in the boot (e.g. the normal case) then
this should be fine but on systems where kgdb has set breakpoints before
the lockdown is enacted than "bad things" will happen.

CVE: CVE-2022-21499
Co-developed-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Signed-off-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull scheduler updates from Ingo Molnar:

 - Updates to scheduler metrics:
     - PELT fixes & enhancements
     - PSI fixes & enhancements
     - Refactor cpu_util_without()

 - Updates to instrumentation/debugging:
     - Remove sched_trace_*() helper functions - can be done via debug
       info
     - Fix double update_rq_clock() warnings

 - Introduce & use "preemption model accessors" to simplify some of the
   Kconfig complexity.

 - Make softirq handling RT-safe.

 - Misc smaller fixes & cleanups.

* tag 'sched-core-2022-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  topology: Remove unused cpu_cluster_mask()
  sched: Reverse sched_class layout
  sched/deadline: Remove superfluous rq clock update in push_dl_task()
  sched/core: Avoid obvious double update_rq_clock warning
  smp: Make softirq handling RT safe in flush_smp_call_function_queue()
  smp: Rename flush_smp_call_function_from_idle()
  sched: Fix missing prototype warnings
  sched/fair: Remove cfs_rq_tg_path()
  sched/fair: Remove sched_trace_*() helper functions
  sched/fair: Refactor cpu_util_without()
  sched/fair: Revise comment about lb decision matrix
  sched/psi: report zeroes for CPU full at the system level
  sched/fair: Delete useless condition in tg_unthrottle_up()
  sched/fair: Fix cfs_rq_clock_pelt() for throttled cfs_rq
  sched/fair: Move calculate of avg_load to a better location
  mailmap: Update my email address to @redhat.com
  MAINTAINERS: Add myself as scheduler topology reviewer
  psi: Fix trigger being fired unexpectedly at initial
  ftrace: Use preemption model accessors for trace header printout
  kcsan: Use preemption model accessors

Pull perf events updates from Ingo Molnar:
 "Platform PMU changes:

   - x86/intel:
      - Add new Intel Alder Lake and Raptor Lake support

   - x86/amd:
      - AMD Zen4 IBS extensions support
      - Add AMD PerfMonV2 support
      - Add AMD Fam19h Branch Sampling support

  Generic changes:

   - signal: Deliver SIGTRAP on perf event asynchronously if blocked

     Perf instrumentation can be driven via SIGTRAP, but this causes a
     problem when SIGTRAP is blocked by a task & terminate the task.

     Allow user-space to request these signals asynchronously (after
     they get unblocked) & also give the information to the signal
     handler when this happens:

       "To give user space the ability to clearly distinguish
        synchronous from asynchronous signals, introduce
        siginfo_t::si_perf_flags and TRAP_PERF_FLAG_ASYNC (opted for
        flags in case more binary information is required in future).

        The resolution to the problem is then to (a) no longer force the
        signal (avoiding the terminations), but (b) tell user space via
        si_perf_flags if the signal was synchronous or not, so that such
        signals can be handled differently (e.g. let user space decide
        to ignore or consider the data imprecise). "

   - Unify/standardize the /sys/devices/cpu/events/* output format.

   - Misc fixes & cleanups"

* tag 'perf-core-2022-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
  perf/x86/amd/core: Fix reloading events for SVM
  perf/x86/amd: Run AMD BRS code only on supported hw
  perf/x86/amd: Fix AMD BRS period adjustment
  perf/x86/amd: Remove unused variable 'hwc'
  perf/ibs: Fix comment
  perf/amd/ibs: Advertise zen4_ibs_extensions as pmu capability attribute
  perf/amd/ibs: Add support for L3 miss filtering
  perf/amd/ibs: Use ->is_visible callback for dynamic attributes
  perf/amd/ibs: Cascade pmu init functions' return value
  perf/x86/uncore: Add new Alder Lake and Raptor Lake support
  perf/x86/uncore: Clean up uncore_pci_ids[]
  perf/x86/cstate: Add new Alder Lake and Raptor Lake support
  perf/x86/msr: Add new Alder Lake and Raptor Lake support
  perf/x86: Add new Alder Lake and Raptor Lake support
  perf/amd/ibs: Use interrupt regs ip for stack unwinding
  perf/x86/amd/core: Add PerfMonV2 overflow handling
  perf/x86/amd/core: Add PerfMonV2 counter control
  perf/x86/amd/core: Detect available counters
  perf/x86/amd/core: Detect PerfMonV2 support
  x86/msr: Add PerfCntrGlobal* registers
  ...

Pull objtool updates from Ingo Molnar:

 - Comprehensive interface overhaul:
   =================================

   Objtool's interface has some issues:

     - Several features are done unconditionally, without any way to
       turn them off. Some of them might be surprising. This makes
       objtool tricky to use, and prevents porting individual features
       to other arches.

     - The config dependencies are too coarse-grained. Objtool
       enablement is tied to CONFIG_STACK_VALIDATION, but it has several
       other features independent of that.

     - The objtool subcmds ("check" and "orc") are clumsy: "check" is
       really a subset of "orc", so it has all the same options.

       The subcmd model has never really worked for objtool, as it only
       has a single purpose: "do some combination of things on an object
       file".

     - The '--lto' and '--vmlinux' options are nonsensical and have
       surprising behavior.

   Overhaul the interface:

      - get rid of subcmds

      - make all features individually selectable

      - remove and/or clarify confusing/obsolete options

      - update the documentation

      - fix some bugs found along the way

 - Fix x32 regression

 - Fix Kbuild cleanup bugs

 - Add scripts/objdump-func helper script to disassemble a single
   function from an object file.

 - Rewrite scripts/faddr2line to be section-aware, by basing it on
   'readelf', moving it away from 'nm', which doesn't handle multiple
   sections well, which can result in decoding failure.

 - Rewrite & fix symbol handling - which had a number of bugs wrt.
   object files that don't have global symbols - which is rare but
   possible. Also fix a bunch of symbol handling bugs found along the
   way.

* tag 'objtool-core-2022-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
  objtool: Fix objtool regression on x32 systems
  objtool: Fix symbol creation
  scripts/faddr2line: Fix overlapping text section failures
  scripts: Create objdump-func helper script
  objtool: Remove libsubcmd.a when make clean
  objtool: Remove inat-tables.c when make clean
  objtool: Update documentation
  objtool: Remove --lto and --vmlinux in favor of --link
  objtool: Add HAVE_NOINSTR_VALIDATION
  objtool: Rename "VMLINUX_VALIDATION" -> "NOINSTR_VALIDATION"
  objtool: Make noinstr hacks optional
  objtool: Make jump label hack optional
  objtool: Make static call annotation optional
  objtool: Make stack validation frame-pointer-specific
  objtool: Add CONFIG_OBJTOOL
  objtool: Extricate sls from stack validation
  objtool: Rework ibt and extricate from stack validation
  objtool: Make stack validation optional
  objtool: Add option to print section addresses
  objtool: Don't print parentheses in function addresses
  ...

Pull locking updates from Ingo Molnar:

 - rwsem cleanups & optimizations/fixes:
    - Conditionally wake waiters in reader/writer slowpaths
    - Always try to wake waiters in out_nolock path

 - Add try_cmpxchg64() implementation, with arch optimizations - and use
   it to micro-optimize sched_clock_{local,remote}()

 - Various force-inlining fixes to address objdump instrumentation-check
   warnings

 - Add lock contention tracepoints:

    lock:contention_begin
    lock:contention_end

 - Misc smaller fixes & cleanups

* tag 'locking-core-2022-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/clock: Use try_cmpxchg64 in sched_clock_{local,remote}
  locking/atomic/x86: Introduce arch_try_cmpxchg64
  locking/atomic: Add generic try_cmpxchg64 support
  futex: Remove a PREEMPT_RT_FULL reference.
  locking/qrwlock: Change "queue rwlock" to "queued rwlock"
  lockdep: Delete local_irq_enable_in_hardirq()
  locking/mutex: Make contention tracepoints more consistent wrt adaptive spinning
  locking: Apply contention tracepoints in the slow path
  locking: Add lock contention tracepoints
  locking/rwsem: Always try to wake waiters in out_nolock path
  locking/rwsem: Conditionally wake waiters in reader/writer slowpaths
  locking/rwsem: No need to check for handoff bit if wait queue empty
  lockdep: Fix -Wunused-parameter for _THIS_IP_
  x86/mm: Force-inline __phys_addr_nodebug()
  x86/kvm/svm: Force-inline GHCB accessors
  task_stack, x86/cea: Force-inline stack helpers

- support for pens with 3 buttons (Joshua Dickens)
- support for HID_DG_SCANTIME to report the timestamp for pen and touch events
  (Joshua Dickens)

- support for wider variety of Huion tablets ported from DIGImend
  project (José Expósito, Nikolai Kondrashov)

- Support for Keychron keyboards (Bryan Cain)

- support for sensor discovery and code cleanups (Basavaraj Natikar)

Pull arm64 updates from Catalin Marinas:

 - Initial support for the ARMv9 Scalable Matrix Extension (SME).

   SME takes the approach used for vectors in SVE and extends this to
   provide architectural support for matrix operations. No KVM support
   yet, SME is disabled in guests.

 - Support for crashkernel reservations above ZONE_DMA via the
   'crashkernel=X,high' command line option.

 - btrfs search_ioctl() fix for live-lock with sub-page faults.

 - arm64 perf updates: support for the Hisilicon "CPA" PMU for
   monitoring coherent I/O traffic, support for Arm's CMN-650 and
   CMN-700 interconnect PMUs, minor driver fixes, kerneldoc cleanup.

 - Kselftest updates for SME, BTI, MTE.

 - Automatic generation of the system register macros from a 'sysreg'
   file describing the register bitfields.

 - Update the type of the function argument holding the ESR_ELx register
   value to unsigned long to match the architecture register size
   (originally 32-bit but extended since ARMv8.0).

 - stacktrace cleanups.

 - ftrace cleanups.

 - Miscellaneous updates, most notably: arm64-specific huge_ptep_get(),
   avoid executable mappings in kexec/hibernate code, drop TLB flushing
   from get_clear_flush() (and rename it to get_clear_contig()),
   ARCH_NR_GPIO bumped to 2048 for ARCH_APPLE.

* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (145 commits)
  arm64/sysreg: Generate definitions for FAR_ELx
  arm64/sysreg: Generate definitions for DACR32_EL2
  arm64/sysreg: Generate definitions for CSSELR_EL1
  arm64/sysreg: Generate definitions for CPACR_ELx
  arm64/sysreg: Generate definitions for CONTEXTIDR_ELx
  arm64/sysreg: Generate definitions for CLIDR_EL1
  arm64/sve: Move sve_free() into SVE code section
  arm64: Kconfig.platforms: Add comments
  arm64: Kconfig: Fix indentation and add comments
  arm64: mm: avoid writable executable mappings in kexec/hibernate code
  arm64: lds: move special code sections out of kernel exec segment
  arm64/hugetlb: Implement arm64 specific huge_ptep_get()
  arm64/hugetlb: Use ptep_get() to get the pte value of a huge page
  arm64: kdump: Do not allocate crash low memory if not needed
  arm64/sve: Generate ZCR definitions
  arm64/sme: Generate defintions for SVCR
  arm64/sme: Generate SMPRI_EL1 definitions
  arm64/sme: Automatically generate SMPRIMAP_EL2 definitions
  arm64/sme: Automatically generate SMIDR_EL1 defines
  arm64/sme: Automatically generate defines for SMCR
  ...

Pull ARM updates from Russell King:

 - amba bus updates

 - simplify ldr_this_cpu assembler macro for uniprocessor builds

 - avoid explicit assembler literal loads

 - more spectre-bhb improvements

 - add Cortex-A9 Errata 764319 workaround

 - add all unwind tables for modules

* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 9204/2: module: Add all unwind tables when load module
  ARM: 9206/1: A9: Add ARM ERRATA 764319 workaround (Updated)
  ARM: 9201/1: spectre-bhb: rely on linker to emit cross-section literal loads
  ARM: 9200/1: spectre-bhb: avoid cross-subsection jump using a numbered label
  ARM: 9199/1: spectre-bhb: use local DSB and elide ISB in loop8 sequence
  ARM: 9198/1: spectre-bhb: simplify BPIALL vector macro
  ARM: 9195/1: entry: avoid explicit literal loads
  ARM: 9194/1: assembler: simplify ldr_this_cpu for !SMP builds
  ARM: 9192/1: amba: fix memory leak in amba_device_try_add()
  ARM: 9193/1: amba: Add amba_read_periphid() helper

Pull s390 updates from Heiko Carstens:

 - Make use of the IBM z16 processor activity instrumentation facility
   to count cryptography operations: add a new PMU device driver so that
   perf can make use of this.

 - Add new IBM z16 extended counter set to cpumf support.

 - Add vdso randomization support.

 - Add missing KCSAN instrumentation to barriers and spinlocks, which
   should make s390's KCSAN support complete.

 - Add support for IPL-complete-control facility: notify the hypervisor
   that kexec finished work and the kernel starts.

 - Improve error logging for PCI.

 - Various small changes to workaround llvm's integrated assembler
   limitations, and one bug, to make it finally possible to compile the
   kernel with llvm's integrated assembler. This also requires to raise
   the minimum clang version to 14.0.0.

 - Various other small enhancements, bug fixes, and cleanups all over
   the place.

* tag 's390-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (48 commits)
  s390/head: get rid of 31 bit leftovers
  scripts/min-tool-version.sh: raise minimum clang version to 14.0.0 for s390
  s390/boot: do not emit debug info for assembly with llvm's IAS
  s390/boot: workaround llvm IAS bug
  s390/purgatory: workaround llvm's IAS limitations
  s390/entry: workaround llvm's IAS limitations
  s390/alternatives: remove padding generation code
  s390/alternatives: provide identical sized orginal/alternative sequences
  s390/cpumf: add new extended counter set for IBM z16
  s390/preempt: disable __preempt_count_add() optimization for PROFILE_ALL_BRANCHES
  s390/stp: clock_delta should be signed
  s390/stp: fix todoff size
  s390/pai: add support for cryptography counters
  entry: Rename arch_check_user_regs() to arch_enter_from_user_mode()
  s390/compat: cleanup compat_linux.h header file
  s390/entry: remove broken and not needed code
  s390/boot: convert parmarea to C
  s390/boot: convert initial lowcore to C
  s390/ptrace: move short psw definitions to ptrace header file
  s390/head: initialize all new psws
  ...

Pull arch/csky updates from Guo Ren:

 - Three atomic optimizations

 - memcpy/memcpy_io optimization

 - Some coding conventions for Kbuild, removing warnings

* tag 'csky-for-linus-5.19-rc1' of https://github.com/c-sky/csky-linux:
  csky: Move $(core-y) into arch/csky/Kbuild
  csky: Remove unused core-y for dts
  csky: Remove unused $(dtb-y) from boot/Makefile
  csky: atomic: Add conditional atomic operations' optimization
  csky: atomic: Add custom atomic.h implementation
  csky: atomic: Optimize cmpxchg with acquire & release
  csky: optimize memcpy_{from,to}io() and memset_io()
  csky: Add C based string functions
  csky: Fix versioncheck warnings
  csky: patch_text: Fixup last cpu should be master
  csky: fix typos in comments

Pull m68k updates from Geert Uytterhoeven:

  - Introduce virtual m68k machine based on Android Goldfish devices

  - defconfig updates

  - Minor fixes and improvements

* tag 'm68k-for-v5.19-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: atari: Make Atari ROM port I/O write macros return void
  m68k: math-emu: Fix dependencies of math emulation support
  m68k: math-emu: Fix typos in comments
  m68k: Wire up syscall_trace_enter/leave for m68k
  m68k: defconfig: Update defconfigs for v5.18-rc1
  m68k: Introduce a virtual m68k machine
  clocksource/drivers: Add a goldfish-timer clocksource
  rtc: goldfish: Use gf_ioread32()/gf_iowrite32()
  tty: goldfish: Introduce gf_ioread32()/gf_iowrite32()

Pull xtensa architecture updates from Max Filippov:

 - support coprocessors on SMP

 - support KCSAN

 - support handling protection faults in noMMU configurations

 - support using coprocessors in the kernel mode

 - support hibernation

 - enable context tracking

 - enable HAVE_VIRT_CPU_ACCOUNTING_GEN

 - support division by 0 exception on cores without HW division option

 - clean up locking in the ISS network driver

 - clean up kernel entry assemly code

 - various minor fixes

* tag 'xtensa-20220523' of https://github.com/jcmvbkbc/linux-xtensa: (36 commits)
  xtensa: Return true/false (not 1/0) from bool function
  xtensa: improve call0 ABI probing
  xtensa: support artificial division by 0 exception
  xtensa: add trap handler for division by zero
  xtensa/simdisk: fix proc_read_simdisk()
  xtensa: no need to initialise statics to 0
  xtensa: clean up labels in the kernel entry assembly
  xtensa: don't leave invalid TLB entry in fast_store_prohibited
  xtensa: fix declaration of _SecondaryResetVector_text_*
  irqchip: irq-xtensa-mx: fix initial IRQ affinity
  xtensa: enable ARCH_HAS_DEBUG_VM_PGTABLE
  xtensa: add hibernation support
  xtensa: support coprocessors on SMP
  xtensa: get rid of stack frame in coprocessor_flush
  xtensa: merge SAVE_CP_REGS_TAB and LOAD_CP_REGS_TAB
  xtensa: add xtensa_xsr macro
  xtensa: handle coprocessor exceptions in kernel mode
  xtensa: use callx0 opcode in fast_coprocessor
  xtensa: clean up excsave1 initialization
  xtensa: clean up declarations in coprocessor.h
  ...

Pull xen updates from Juergen Gross:

 - decouple the PV interface from kernel internals in the Xen
   scsifront/scsiback pv drivers

 - harden the Xen scsifront PV driver against a malicious backend driver

 - simplify Xen PV frontend driver ring page setup

 - support Xen setups with multiple domains created at boot time to
   tolerate Xenstore coming up late

 - two small cleanup patches

* tag 'for-linus-5.19-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (29 commits)
  xen: add support for initializing xenstore later as HVM domain
  xen: sync xs_wire.h header with upstream xen
  x86: xen: remove STACK_FRAME_NON_STANDARD from xen_cpuid
  xen-blk{back,front}: Update contact points for buffer_squeeze_duration_ms and feature_persistent
  xen/xenbus: eliminate xenbus_grant_ring()
  xen/sndfront: use xenbus_setup_ring() and xenbus_teardown_ring()
  xen/usbfront: use xenbus_setup_ring() and xenbus_teardown_ring()
  xen/scsifront: use xenbus_setup_ring() and xenbus_teardown_ring()
  xen/pcifront: use xenbus_setup_ring() and xenbus_teardown_ring()
  xen/drmfront: use xenbus_setup_ring() and xenbus_teardown_ring()
  xen/tpmfront: use xenbus_setup_ring() and xenbus_teardown_ring()
  xen/netfront: use xenbus_setup_ring() and xenbus_teardown_ring()
  xen/blkfront: use xenbus_setup_ring() and xenbus_teardown_ring()
  xen/xenbus: add xenbus_setup_ring() service function
  xen: update ring.h
  xen/shbuf: switch xen-front-pgdir-shbuf to use INVALID_GRANT_REF
  xen/dmabuf: switch gntdev-dmabuf to use INVALID_GRANT_REF
  xen/sound: switch xen_snd_front to use INVALID_GRANT_REF
  xen/drm: switch xen_drm_front to use INVALID_GRANT_REF
  xen/usb: switch xen-hcd to use INVALID_GRANT_REF
  ...

Merge tag 'platform-drivers-x86-v5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86

Pull x86 platform driver updates from Hans de Goede:
 "This includes some small changes to kernel/stop_machine.c and arch/x86
  which are deps of the new Intel IFS support.

  Highlights:

   - New drivers:
       - Intel "In Field Scan" (IFS) support
       - Winmate FM07/FM07P buttons
       - Mellanox SN2201 support

   -  AMD PMC driver enhancements

   -  Lots of various other small fixes and hardware-id additions"

* tag 'platform-drivers-x86-v5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (54 commits)
  platform/x86/intel/ifs: Add CPU_SUP_INTEL dependency
  platform/x86: intel_cht_int33fe: Set driver data
  platform/x86: intel-hid: fix _DSM function index handling
  platform/x86: toshiba_acpi: use kobj_to_dev()
  platform/x86: samsung-laptop: use kobj_to_dev()
  platform/x86: gigabyte-wmi: Add support for Z490 AORUS ELITE AC and X570 AORUS ELITE WIFI
  tools/power/x86/intel-speed-select: Fix warning for perf_cap.cpu
  tools/power/x86/intel-speed-select: Display error on turbo mode disabled
  Documentation: In-Field Scan
  platform/x86/intel/ifs: add ABI documentation for IFS
  trace: platform/x86/intel/ifs: Add trace point to track Intel IFS operations
  platform/x86/intel/ifs: Add IFS sysfs interface
  platform/x86/intel/ifs: Add scan test support
  platform/x86/intel/ifs: Authenticate and copy to secured memory
  platform/x86/intel/ifs: Check IFS Image sanity
  platform/x86/intel/ifs: Read IFS firmware image
  platform/x86/intel/ifs: Add stub driver for In-Field Scan
  stop_machine: Add stop_core_cpuslocked() for per-core operations
  x86/msr-index: Define INTEGRITY_CAPABILITIES MSR
  x86/microcode/intel: Expose collect_cpu_info_early() for IFS
  ...