This patch fixes an issue that reconnection is possible to fail
because unexpected state handling happens by the irqs. To fix the issue,
the driver disables the controller's irqs when disconnected.

Fixes: 746bfe63 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch fixes an issue that this driver ignores errors other than
the non-existence of the device, f.e. a memory allocation failure
in devm_phy_get(). So, this patch replaces devm_phy_get() with
devm_phy_optional_get().
Reported-by: Simon Horman <horms+renesas@verge.net.au>
Fixes: 279d4bc6 ("usb: gadget: udc: renesas_usb3: add support for generic phy")
Cc: <stable@vger.kernel.org> # v4.15+
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch fixes an issue that this driver cannot call phy_init()
if a gadget driver is alreadly loaded because usb_add_gadget_udc()
might call renesas_usb3_start() via .udc_start.
This patch also revises the typo (s/an optional/optional/).

Fixes: 279d4bc6 ("usb: gadget: udc: renesas_usb3: add support for generic phy")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch fixes an issue that this driver causes panic if a gadget
driver is already loaded because usb_add_gadget_udc() might call
renesas_usb3_start() via .udc_start, and then pm_runtime_get_sync()
in renesas_usb3_start() doesn't work correctly.
Note that the usb3_to_dev() macro should not be called at this timing
because the macro uses the gadget structure.

Fixes: cf06df3f ("usb: gadget: udc: renesas_usb3: move pm_runtime_{en,dis}able()")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch fixes an issue that this driver doesn't remove its debugfs.

Fixes: 43ba968b ("usb: gadget: udc: renesas_usb3: add debugfs to set the b-device mode")
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The composite framework allows us to create gadgets composed from many
different functions, which need to fit into a single configuration
descriptor.

Some functions (like uvc) can produce configuration descriptors upwards
of 2500 bytes on their own.

This patch increases the limit from 1024 bytes to 4096.
Signed-off-by: Joel Pepper <joel.pepper@rwth-aachen.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

dwc3_ep_dequeue() waits for completion of End Transfer command using
wait_event_lock_irq(), which will release the dwc3->lock while waiting
and reacquire after completion. This allows a potential race condition
with ep_disable() which also removes all requests from started_list
and pending_list.

The check for NULL r->trb should catch this but currently it exits to
the wrong 'out1' label which calls dwc3_gadget_giveback(). Since its
list entry was already removed, if CONFIG_DEBUG_LIST is enabled a
'list_del corruption' bug is thrown since its next/prev pointers are
already LIST_POISON1/2. If r->trb is NULL it should simply exit to
'out0'.

Fixes: cf3113d8 ("usb: dwc3: gadget: properly increment dequeue pointer on ep_dequeue")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Fixes the following sparse warning:

drivers/usb/dwc3/gadget.c:169:6: warning:
 symbol 'dwc3_gadget_del_and_unmap_request' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Fix to return error code -ENOMEM from the alloc fail error handling
case instead of 0, as done elsewhere in this function.

Fixes: ecd29dab ("usb: dwc2: pci: Handle error cleanup in probe")
Reviewed-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

By clearing NAK status of EP, core will send ZLP
to IN token and assert NAK interrupt relying
on TxFIFO status only.

The WA applies only to core versions from 2.72a
to 4.00a (including both). Also for FS_IOT_1.00a
and HS_IOT_1.00a.
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

devm_regulator_get_optional returns -ENODEV if the regulator isn't
there, so if that's the case we have to make sure not to leave -ENODEV
in the regulator pointer.

Also, make sure we return 0 in that case, but correctly propagate any
other errors. Also propagate the error from _dwc2_hcd_start.

Fixes: 531ef5eb ("usb: dwc2: add support for host mode external vbus supply")
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In 4.17-rc, commit 03ea6d6e ("usb: dwc2: Enable power down")
caused the HiKey board to not correctly handle switching between
usb-gadget and usb-host mode.

Unplugging the OTG port would result in:
[   42.240973] dwc2 f72c0000.usb: dwc2_restore_host_registers: no host registers to restore
[   42.249066] dwc2 f72c0000.usb: dwc2_host_exit_hibernation: failed to restore host registers

And the USB-host ports would not function.

And plugging in the OTG port, we would see:
[   46.046557] WARNING: CPU: 3 PID: 6 at drivers/usb/dwc2/gadget.c:260 dwc2_hsotg_init_fifo+0x194/0x1a0
[   46.055761] CPU: 3 PID: 6 Comm: kworker/u16:0 Not tainted 4.17.0-rc5-00030-ge67da8c #231
[   46.055767] Hardware name: HiKey Development Board (DT)
[   46.055784] Workqueue: dwc2 dwc2_conn_id_status_change
...

Thus, this patch sets the hisi params to disable the power_down
flag by default, and gets thing working again.

Cc: John Youn <johnyoun@synopsys.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Artur Petrosyan <arturp@synopsys.com>
Cc: Grigor Tovmasyan <tovmasya@synopsys.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Added descriptions for all not described parameters.
Fix all kernel doc's warnings.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Introduce FSL_USB2_PHY_UTMI_DUAL in gadget driver for setting
phy in SOCs with utmi dual phy
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Tested-by: Tiago Brusamarello <tbrusa@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Fix sparse warning

Fixes: 5f0b74e5 ("USB: dwc3: get extcon device by OF graph bindings")
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We dont' need to touch req->direction or req->epnum from
ep_queue(). It's enough that we initialize both fields from
alloc_request() and just keep them for the entire lifetime of the
request.

No functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Instead of *always* calling dwc3_gadget_ep_get_transfer_index() after
sending a Start Transfer command, we can call it once from
dwc3_send_gadget_ep_cmd() itself.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Instead of returning resource index number just to assign it to a
field inside 'dep' which was passed as argument, we can assing
dep->resource_index from inside dwc3_gadget_ep_get_transfer_index()
itself.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We will *always* start transfer to the next uFrame number aligned to
dep->interval.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In case we have many started requests and one of them in the middle is
completed with Missed Isoc, let's not End Transfer as that would
result in us loosing (possibly) many more intervals.

Instead, let's allow the controller to go through its list of started
requests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

XferNotReady and XferInProgress give us the uFrame number we're
currently in. Printing that out on tracepoints may help us find bugs
in transfer scheduling.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Avoid a prototype when the function can be defined earlier. No
functional changes, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Instead of having a prototype for a function that's defined a few
lines down, let's just move definition to the place where prototype
was.

No functional changes, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In a few places, the argument is completely unnecessary. On places
where it's needed, we can get it from dep->dwc.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Those two arguments refer to a single bitfield in the register. In
order to simplify the code, we can combine them into a single argument
and expect caller to pass the correct action argument at all times.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This just makes it slightly easier to read. No functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

No functional changes, it just makes the code slightly easier to read.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Code is just as readable without it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We can declare it inside list_for_each_entry_safe() loop and reduce
its scope.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Misc cleanup. No functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We will only have event status of IOC when IOC bit is set in
TRB. There's no need to check both bits.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We know that only OUT endpoints can trigger SHORT. We also know that
count MUST be > 0 whenever SHORT triggers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This will make it easier to figure out the reason for the event. That
information really helps debugging certain problems.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We can just call reclaim_trb_linear instead of reimplementing it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Minor cleanup, no functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We are trying to kick transfers on Isochronous endpoints in a more
controlled manner now. And this ended up rendering this piece of code
unnecessary.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

instead of having one big loop, let's split it down into two smaller
handlers: one for linear buffers and one for scatterlist.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Just a minor simplification, no functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

After all the previous changes, it's now a lot clearer how isoc
transfers should be managed. We don't need to try to End Transfers
from ep_queue since that's already done by cleanup_requests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>