- 08 Mar, 2016 8 commits
-
-
Benjamin Coddington authored
commit d9dfd8d7 upstream. In the case where d_add_unique() finds an appropriate alias to use it will have already incremented the reference count. An additional dget() to swap the open context's dentry is unnecessary and will leak a reference. Signed-off-by:
Benjamin Coddington <bcodding@redhat.com> Fixes: 275bb307 ("NFSv4: Move dentry instantiation into the NFSv4-...") Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
John Youn authored
commit c4509601 upstream. The assignement of EP transfer resources was not handled properly in the dwc3 driver. Commit aebda618 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE") previously fixed one aspect of this where resources may be exhausted with multiple calls to SET_INTERFACE. However, it introduced an issue where composite devices with multiple interfaces can be assigned the same transfer resources for different endpoints. This patch solves both issues. The assignment of transfer resources cannot perfectly follow the data book due to the fact that the controller driver does not have all knowledge of the configuration in advance. It is given this information piecemeal by the composite gadget framework after every SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook programming model in this scenario can cause errors. For two reasons: 1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple interfaces. 2) The databook does not mention doing more DEPXFERCFG for new endpoint on alt setting (8.1.6). The following simplified method is used instead: All hardware endpoints can be assigned a transfer resource and this setting will stay persistent until either a core reset or hibernation. So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for every hardware endpoint as well. We are guaranteed that there are as many transfer resources as endpoints. This patch triggers off of the calling dwc3_gadget_start_config() for EP0-out, which always happens first, and which should only happen in one of the above conditions. Fixes: aebda618 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE") Reported-by:
Ravi Babu <ravibabu@ti.com> Signed-off-by:
John Youn <johnyoun@synopsys.com> Signed-off-by:
Felipe Balbi <balbi@kernel.org> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Konrad Rzeszutek Wilk authored
commit 4d8c8bd6 upstream. Occasionaly PV guests would crash with: pciback 0000:00:00.1: Xen PCI mapped GSI0 to IRQ16 BUG: unable to handle kernel paging request at 0000000d1a8c0be0 .. snip.. <ffffffff8139ce1b>] find_next_bit+0xb/0x10 [<ffffffff81387f22>] cpumask_next_and+0x22/0x40 [<ffffffff813c1ef8>] pci_device_probe+0xb8/0x120 [<ffffffff81529097>] ? driver_sysfs_add+0x77/0xa0 [<ffffffff815293e4>] driver_probe_device+0x1a4/0x2d0 [<ffffffff813c1ddd>] ? pci_match_device+0xdd/0x110 [<ffffffff81529657>] __device_attach_driver+0xa7/0xb0 [<ffffffff815295b0>] ? __driver_attach+0xa0/0xa0 [<ffffffff81527622>] bus_for_each_drv+0x62/0x90 [<ffffffff8152978d>] __device_attach+0xbd/0x110 [<ffffffff815297fb>] device_attach+0xb/0x10 [<ffffffff813b75ac>] pci_bus_add_device+0x3c/0x70 [<ffffffff813b7618>] pci_bus_add_devices+0x38/0x80 [<ffffffff813dc34e>] pcifront_scan_root+0x13e/0x1a0 [<ffffffff817a0692>] pcifront_backend_changed+0x262/0x60b [<ffffffff814644c6>] ? xenbus_gather+0xd6/0x160 [<ffffffff8120900f>] ? put_object+0x2f/0x50 [<ffffffff81465c1d>] xenbus_otherend_changed+0x9d/0xa0 [<ffffffff814678ee>] backend_changed+0xe/0x10 [<ffffffff81463a28>] xenwatch_thread+0xc8/0x190 [<ffffffff810f22f0>] ? woken_wake_function+0x10/0x10 which was the result of two things: When we call pci_scan_root_bus we would pass in 'sd' (sysdata) pointer which was an 'pcifront_sd' structure. However in the pci_device_add it expects that the 'sd' is 'struct sysdata' and sets the dev->node to what is in sd->node (offset 4): set_dev_node(&dev->dev, pcibus_to_node(bus)); __pcibus_to_node(const struct pci_bus *bus) { const struct pci_sysdata *sd = bus->sysdata; return sd->node; } However our structure was pcifront_sd which had nothing at that offset: struct pcifront_sd { int domain; /* 0 4 */ /* XXX 4 bytes hole, try to pack */ struct pcifront_device * pdev; /* 8 8 */ } That is an hole - filled with garbage as we used kmalloc instead of kzalloc (the second problem). This patch fixes the issue by: 1) Use kzalloc to initialize to a well known state. 2) Put 'struct pci_sysdata' at the start of 'pcifront_sd'. That way access to the 'node' will access the right offset. Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
-
Konrad Rzeszutek Wilk authored
commit d159457b upstream. Commit 8135cf8b (xen/pciback: Save xen_pci_op commands before processing it) broke enabling MSI-X because it would never copy the resulting vectors into the response. The number of vectors requested was being overwritten by the return value (typically zero for success). Save the number of vectors before processing the op, so the correct number of vectors are copied afterwards. Signed-off-by:
Jan Beulich <jbeulich@suse.com> Signed-off-by:
-
Konrad Rzeszutek Wilk authored
commit 8d47065f upstream. Commit 408fb0e5 (xen/pciback: Don't allow MSI-X ops if PCI_COMMAND_MEMORY is not set) prevented enabling MSI-X on passed-through virtual functions, because it checked the VF for PCI_COMMAND_MEMORY but this is not a valid bit for VFs. Instead, check the physical function for PCI_COMMAND_MEMORY. Signed-off-by:
-
Christoph Hellwig authored
commit 50ab8ec7 upstream. See http: //www.infradead.org/rpr.html X-Evolution-Source: 1451162204.2173.11@leira.trondhjem.org Content-Transfer-Encoding: 8bit Mime-Version: 1.0 We support OFFSET_MAX just fine, so don't round down below it. Also switch to using min_t to make the helper more readable. Signed-off-by:
Christoph Hellwig <hch@lst.de> Fixes: 433c9237 ("NFS: Clean up nfs_size_to_loff_t()") Signed-off-by:
-
Ben Hutchings authored
Commit a1383cd8 ("crypto: skcipher - Add crypto_skcipher_has_setkey") was incorrectly backported to the 3.2.y and 3.16.y stable branches. We need to set ablkcipher_tfm::has_setkey in the crypto_init_blkcipher_ops_async() and crypto_init_givcipher_ops() functions as well as crypto_init_ablkcipher_ops(). Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Andy Lutomirski authored
commit 3d44d51b upstream. This doesn't seem to fix a regression -- I don't think the CLAC was ever there. I double-checked in a debugger: entries through the int80 gate do not automatically clear AC. Stable maintainers: I can provide a backport to 4.3 and earlier if needed. This needs to be backported all the way to 3.10. Reported-by:
Brian Gerst <brgerst@gmail.com> Signed-off-by:
Andy Lutomirski <luto@kernel.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 63bcff2a ("x86, smap: Add STAC and CLAC instructions to control user space access") Link: http://lkml.kernel.org/r/b02b7e71ae54074be01fc171cbd4b72517055c0e.1456345086.git.luto@kernel.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> [ kamal: backport to 3.10 through 3.19-stable: file rename; context ] Signed-off-by:
Kamal Mostafa <kamal@canonical.com> Signed-off-by:
-
- 04 Mar, 2016 23 commits
-
-
Simon Guinot authored
commit 59ceeaaf upstream. In __request_region, if a conflict with a BUSY and MUXED resource is detected, then the caller goes to sleep and waits for the resource to be released. A pointer on the conflicting resource is kept. At wake-up this pointer is used as a parent to retry to request the region. A first problem is that this pointer might well be invalid (if for example the conflicting resource have already been freed). Another problem is that the next call to __request_region() fails to detect a remaining conflict. The previously conflicting resource is passed as a parameter and __request_region() will look for a conflict among the children of this resource and not at the resource itself. It is likely to succeed anyway, even if there is still a conflict. Instead, the parent of the conflicting resource should be passed to __request_region(). As a fix, this patch doesn't update the parent resource pointer in the case we have to wait for a muxed region right after. Reported-and-tested-by:
Vincent Pelletier <plr.vincent@gmail.com> Signed-off-by:
Simon Guinot <simon.guinot@sequanux.org> Tested-by:
Vincent Donnefort <vdonnefort@gmail.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Jan Kara authored
commit 74dae427 upstream. Competing overwrite DIO in dioread_nolock mode will just overwrite pointer to io_end in the inode. This may result in data corruption or extent conversion happening from IO completion interrupt because we don't properly set buffer_defer_completion() when unlocked DIO races with locked DIO to unwritten extent. Since unlocked DIO doesn't need io_end for anything, just avoid allocating it and corrupting pointer from inode for locked DIO. A cleaner fix would be to avoid these games with io_end pointer from the inode but that requires more intrusive changes so we leave that for later. Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Jan Kara authored
commit ed8ad838 upstream. ext4 can update bh->b_state non-atomically in _ext4_get_block() and ext4_da_get_block_prep(). Usually this is fine since bh is just a temporary storage for mapping information on stack but in some cases it can be fully living bh attached to a page. In such case non-atomic update of bh->b_state can race with an atomic update which then gets lost. Usually when we are mapping bh and thus updating bh->b_state non-atomically, nobody else touches the bh and so things work out fine but there is one case to especially worry about: ext4_finish_bio() uses BH_Uptodate_Lock on the first bh in the page to synchronize handling of PageWriteback state. So when blocksize < pagesize, we can be atomically modifying bh->b_state of a buffer that actually isn't under IO and thus can race e.g. with delalloc trying to map that buffer. The result is that we can mistakenly set / clear BH_Uptodate_Lock bit resulting in the corruption of PageWriteback state or missed unlock of BH_Uptodate_Lock. Fix the problem by always updating bh->b_state bits atomically. Reported-by:
Nikolay Borisov <kernel@kyup.com> Signed-off-by:
-
Gerd Hoffmann authored
commit 34855706 upstream. This avoids integer overflows on 32bit machines when calculating reloc_info size, as reported by Alan Cox. Cc: gnomes@lxorguk.ukuu.org.uk Signed-off-by:
Gerd Hoffmann <kraxel@redhat.com> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Rasmus Villemoes authored
commit bc3f5d8c upstream. We need to use post-decrement to get the pci_map_page undone also for i==0, and to avoid some very unpleasant behaviour if pci_map_page failed already at i==0. Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Takashi Iwai authored
commit 13d5e5d4 upstream. The commit [7f0973e9: ALSA: seq: Fix lockdep warnings due to double mutex locks] split the management of two linked lists (source and destination) into two individual calls for avoiding the AB/BA deadlock. However, this may leave the possible double deletion of one of two lists when the counterpart is being deleted concurrently. It ends up with a list corruption, as revealed by syzkaller fuzzer. This patch fixes it by checking the list emptiness and skipping the deletion and the following process. BugLink: http://lkml.kernel.org/r/CACT4Y+bay9qsrz6dQu31EcGaH9XwfW7o3oBzSQUG9fMszoh=Sg@mail.gmail.com Fixes: 7f0973e9 ('ALSA: seq: Fix lockdep warnings due to 'double mutex locks) Reported-by:
Dmitry Vyukov <dvyukov@google.com> Tested-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Arnd Bergmann authored
commit b33c8ff4 upstream. In my randconfig tests, I came across a bug that involves several components: * gcc-4.9 through at least 5.3 * CONFIG_GCOV_PROFILE_ALL enabling -fprofile-arcs for all files * CONFIG_PROFILE_ALL_BRANCHES overriding every if() * The optimized implementation of do_div() that tries to replace a library call with an division by multiplication * code in drivers/media/dvb-frontends/zl10353.c doing u32 adc_clock = 450560; /* 45.056 MHz */ if (state->config.adc_clock) adc_clock = state->config.adc_clock; do_div(value, adc_clock); In this case, gcc fails to determine whether the divisor in do_div() is __builtin_constant_p(). In particular, it concludes that __builtin_constant_p(adc_clock) is false, while __builtin_constant_p(!!adc_clock) is true. That in turn throws off the logic in do_div() that also uses __builtin_constant_p(), and instead of picking either the constant- optimized division, and the code in ilog2() that uses __builtin_constant_p() to figure out whether it knows the answer at compile time. The result is a link error from failing to find multiple symbols that should never have been called based on the __builtin_constant_p(): dvb-frontends/zl10353.c:138: undefined reference to `____ilog2_NaN' dvb-frontends/zl10353.c:138: undefined reference to `__aeabi_uldivmod' ERROR: "____ilog2_NaN" [drivers/media/dvb-frontends/zl10353.ko] undefined! ERROR: "__aeabi_uldivmod" [drivers/media/dvb-frontends/zl10353.ko] undefined! This patch avoids the problem by changing __trace_if() to check whether the condition is known at compile-time to be nonzero, rather than checking whether it is actually a constant. I see this one link error in roughly one out of 1600 randconfig builds on ARM, and the patch fixes all known instances. Link: http://lkml.kernel.org/r/1455312410-1058841-1-git-send-email-arnd@arndb.deAcked-by:
Nicolas Pitre <nico@linaro.org> Fixes: ab3c9c68 ("branch tracer, intel-iommu: fix build with CONFIG_BRANCH_TRACER=y") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit f3775549 upstream. The tracepoint infrastructure uses RCU sched protection to enable and disable tracepoints safely. There are some instances where tracepoints are used in infrastructure code (like kfree()) that get called after a CPU is going offline, and perhaps when it is coming back online but hasn't been registered yet. This can probuce the following warning: [ INFO: suspicious RCU usage. ] 4.4.0-00006-g0fe53e8-dirty #34 Tainted: G S ------------------------------- include/trace/events/kmem.h:141 suspicious rcu_dereference_check() usage! other info that might help us debug this: RCU used illegally from offline CPU! rcu_scheduler_active = 1, debug_locks = 1 no locks held by swapper/8/0. stack backtrace: CPU: 8 PID: 0 Comm: swapper/8 Tainted: G S 4.4.0-00006-g0fe53e8-dirty #34 Call Trace: [c0000005b76c78d0] [c0000000008b9540] .dump_stack+0x98/0xd4 (unreliable) [c0000005b76c7950] [c00000000010c898] .lockdep_rcu_suspicious+0x108/0x170 [c0000005b76c79e0] [c00000000029adc0] .kfree+0x390/0x440 [c0000005b76c7a80] [c000000000055f74] .destroy_context+0x44/0x100 [c0000005b76c7b00] [c0000000000934a0] .__mmdrop+0x60/0x150 [c0000005b76c7b90] [c0000000000e3ff0] .idle_task_exit+0x130/0x140 [c0000005b76c7c20] [c000000000075804] .pseries_mach_cpu_die+0x64/0x310 [c0000005b76c7cd0] [c000000000043e7c] .cpu_die+0x3c/0x60 [c0000005b76c7d40] [c0000000000188d8] .arch_cpu_idle_dead+0x28/0x40 [c0000005b76c7db0] [c000000000101e6c] .cpu_startup_entry+0x50c/0x560 [c0000005b76c7ed0] [c000000000043bd8] .start_secondary+0x328/0x360 [c0000005b76c7f90] [c000000000008a6c] start_secondary_prolog+0x10/0x14 This warning is not a false positive either. RCU is not protecting code that is being executed while the CPU is offline. Instead of playing "whack-a-mole(TM)" and adding conditional statements to the tracepoints we find that are used in this instance, simply add a cpu_online() test to the tracepoint code where the tracepoint will be ignored if the CPU is offline. Use of raw_smp_processor_id() is fine, as there should never be a case where the tracepoint code goes from running on a CPU that is online and suddenly gets migrated to a CPU that is offline. Link: http://lkml.kernel.org/r/1455387773-4245-1-git-send-email-kda@linux-powerpc.orgReported-by:
Denis Kirjanov <kda@linux-powerpc.org> Fixes: 97e1c18e ("tracing: Kernel Tracepoints") Signed-off-by:
-
Andy Shevchenko authored
commit ee1cdcda upstream. The commit 2895b2ca ("dmaengine: dw: fix cyclic transfer callbacks") re-enabled BLOCK interrupts with regard to make cyclic transfers work. However, this change becomes a regression for non-cyclic transfers as interrupt counters under stress test had been grown enormously (approximately per 4-5 bytes in the UART loop back test). Taking into consideration above enable BLOCK interrupts if and only if channel is programmed to perform cyclic transfer. Fixes: 2895b2ca ("dmaengine: dw: fix cyclic transfer callbacks") Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Mans Rullgard <mans@mansr.com> Tested-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Takashi Iwai authored
commit d99a36f4 upstream. When multiple concurrent writes happen on the ALSA sequencer device right after the open, it may try to allocate vmalloc buffer for each write and leak some of them. It's because the presence check and the assignment of the buffer is done outside the spinlock for the pool. The fix is to move the check and the assignment into the spinlock. (The current implementation is suboptimal, as there can be multiple unnecessary vmallocs because the allocation is done before the check in the spinlock. But the pool size is already checked beforehand, so this isn't a big problem; that is, the only possible path is the multiple writes before any pool assignment, and practically seen, the current coverage should be "good enough".) The issue was triggered by syzkaller fuzzer. BugLink: http://lkml.kernel.org/r/CACT4Y+bSzazpXNvtAr=WXaL8hptqjHwqEyFA+VN2AWEx=aurkg@mail.gmail.comReported-by:
-
Takashi Iwai authored
commit 24db8bba upstream. The kernel memory allocators already report the errors when the requested allocation fails, thus we don't need to warn it again in each caller side. Signed-off-by:
-
Hannes Reinecke authored
commit 2d99b55d upstream. Commit 35dc2483 introduced a check for current->mm to see if we have a user space context and only copies data if we do. Now if an IO gets interrupted by a signal data isn't copied into user space any more (as we don't have a user space context) but user space isn't notified about it. This patch modifies the behaviour to return -EINTR from bio_uncopy_user() to notify userland that a signal has interrupted the syscall, otherwise it could lead to a situation where the caller may get a buffer with no data returned. This can be reproduced by issuing SG_IO ioctl()s in one thread while constantly sending signals to it. Fixes: 35dc2483 [SCSI] sg: Fix user memory corruption when SG_IO is interrupted by a signal Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
Jens Axboe <axboe@fb.com> [ luis: backported to 3.16: based on Johannes' backport to 3.14 ] Signed-off-by:
-
Eryu Guan authored
commit bcff2488 upstream. I notice ext4/307 fails occasionally on ppc64 host, reporting md5 checksum mismatch after moving data from original file to donor file. The reason is that move_extent_per_page() calls __block_write_begin() and block_commit_write() to write saved data from original inode blocks to donor inode blocks, but __block_write_begin() not only maps buffer heads but also reads block content from disk if the size is not block size aligned. At this time the physical block number in mapped buffer head is pointing to the donor file not the original file, and that results in reading wrong data to page, which get written to disk in following block_commit_write call. This also can be reproduced by the following script on 1k block size ext4 on x86_64 host: mnt=/mnt/ext4 donorfile=$mnt/donor testfile=$mnt/testfile e4compact=~/xfstests/src/e4compact rm -f $donorfile $testfile # reserve space for donor file, written by 0xaa and sync to disk to # avoid EBUSY on EXT4_IOC_MOVE_EXT xfs_io -fc "pwrite -S 0xaa 0 1m" -c "fsync" $donorfile # create test file written by 0xbb xfs_io -fc "pwrite -S 0xbb 0 1023" -c "fsync" $testfile # compute initial md5sum md5sum $testfile | tee md5sum.txt # drop cache, force e4compact to read data from disk echo 3 > /proc/sys/vm/drop_caches # test defrag echo "$testfile" | $e4compact -i -v -f $donorfile # check md5sum md5sum -c md5sum.txt Fix it by creating & mapping buffer heads only but not reading blocks from disk, because all the data in page is guaranteed to be up-to-date in mext_page_mkuptodate(). Signed-off-by:
Eryu Guan <guaneryu@gmail.com> Signed-off-by:
-
Insu Yun authored
commit 46901760 upstream. Since sizeof(ext_new_group_data) > sizeof(ext_new_flex_group_data), integer overflow could be happened. Therefore, need to fix integer overflow sanitization. Signed-off-by:
Insu Yun <wuninsu@gmail.com> Signed-off-by:
-
James Bottomley authored
commit 90a88d6e upstream. This softlockup is currently happening: [ 444.088002] NMI watchdog: BUG: soft lockup - CPU#1 stuck for 22s! [kworker/1:1:29] [ 444.088002] Modules linked in: lpfc(-) qla2x00tgt(O) qla2xxx_scst(O) scst_vdisk(O) scsi_transport_fc libcrc32c scst(O) dlm configfs nfsd lockd grace nfs_acl auth_rpcgss sunrpc ed d snd_pcm_oss snd_mixer_oss snd_seq snd_seq_device dm_mod iTCO_wdt snd_hda_codec_realtek snd_hda_codec_generic gpio_ich iTCO_vendor_support ppdev snd_hda_intel snd_hda_codec snd_hda _core snd_hwdep tg3 snd_pcm snd_timer libphy lpc_ich parport_pc ptp acpi_cpufreq snd pps_core fjes parport i2c_i801 ehci_pci tpm_tis tpm sr_mod cdrom soundcore floppy hwmon sg 8250_ fintek pcspkr i915 drm_kms_helper uhci_hcd ehci_hcd drm fb_sys_fops sysimgblt sysfillrect syscopyarea i2c_algo_bit usbcore button video usb_common fan ata_generic ata_piix libata th ermal [ 444.088002] CPU: 1 PID: 29 Comm: kworker/1:1 Tainted: G O 4.4.0-rc5-2.g1e923a3-default #1 [ 444.088002] Hardware name: FUJITSU SIEMENS ESPRIMO E /D2164-A1, BIOS 5.00 R1.10.2164.A1 05/08/2006 [ 444.088002] Workqueue: fc_wq_4 fc_rport_final_delete [scsi_transport_fc] [ 444.088002] task: f6266ec0 ti: f6268000 task.ti: f6268000 [ 444.088002] EIP: 0060:[<c07e7044>] EFLAGS: 00000286 CPU: 1 [ 444.088002] EIP is at _raw_spin_unlock_irqrestore+0x14/0x20 [ 444.088002] EAX: 00000286 EBX: f20d3800 ECX: 00000002 EDX: 00000286 [ 444.088002] ESI: f50ba800 EDI: f2146848 EBP: f6269ec8 ESP: f6269ec8 [ 444.088002] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 [ 444.088002] CR0: 8005003b CR2: 08f96600 CR3: 363ae000 CR4: 000006d0 [ 444.088002] Stack: [ 444.088002] f6269eec c066b0f7 00000286 f2146848 f50ba808 f50ba800 f50ba800 f2146a90 [ 444.088002] f2146848 f6269f08 f8f0a4ed f3141000 f2146800 f2146a90 f619fa00 00000040 [ 444.088002] f6269f40 c026cb25 00000001 166c6392 00000061 f6757140 f6136340 00000004 [ 444.088002] Call Trace: [ 444.088002] [<c066b0f7>] scsi_remove_target+0x167/0x1c0 [ 444.088002] [<f8f0a4ed>] fc_rport_final_delete+0x9d/0x1e0 [scsi_transport_fc] [ 444.088002] [<c026cb25>] process_one_work+0x155/0x3e0 [ 444.088002] [<c026cde7>] worker_thread+0x37/0x490 [ 444.088002] [<c027214b>] kthread+0x9b/0xb0 [ 444.088002] [<c07e72c1>] ret_from_kernel_thread+0x21/0x40 What appears to be happening is that something has pinned the target so it can't go into STARGET_DEL via final release and the loop in scsi_remove_target spins endlessly until that happens. The fix for this soft lockup is to not keep looping over a device that we've called remove on but which hasn't gone into DEL state. This patch will retain a simplistic memory of the last target and not keep looping over it. Reported-by:
Sebastian Herbszt <herbszt@gmx.de> Tested-by:
James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by:
-
Stefan Haberland authored
commit 9d862aba upstream. Add refcount to the DASD device when a summary unit check worker is scheduled. This prevents that the device is set offline with worker in place. Signed-off-by:
Stefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Stefan Haberland authored
commit 020bf042 upstream. The channel checks the specified length and the provided amount of data for CCWs and provides an incorrect length error if the size does not match. Under z/VM with simulation activated the length may get changed. Having the suppress length indication bit set is stated as good CCW coding practice and avoids errors under z/VM. Signed-off-by:
-
Anton Protopopov authored
commit 4b550af5 upstream. The setup_ntlmv2_rsp() function may return positive value ENOMEM instead of -ENOMEM in case of kmalloc failure. Signed-off-by:
Anton Protopopov <a.s.protopopov@gmail.com> Signed-off-by:
Steve French <smfrench@gmail.com> Signed-off-by:
-
Rasmus Villemoes authored
commit ed3f9fd1 upstream. This fails to undo the setup for pin==0; moreover, something interesting happens if the setup failed already at pin==0. Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1455048677-19882-3-git-send-email-linux@rasmusvillemoes.dk (cherry picked from commit 2417c8c0) Signed-off-by:
-
Andreas Schwab authored
commit f15838e9 upstream. Since binutils 2.26 BFD is doing suffix merging on STRTAB sections. But dedotify modifies the symbol names in place, which can also modify unrelated symbols with a name that matches a suffix of a dotted name. To remove the leading dot of a symbol name we can just increment the pointer into the STRTAB section instead. Backport to all stables to avoid breakage when people update their binutils - mpe. Signed-off-by:
Andreas Schwab <schwab@linux-m68k.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Jani Nikula authored
commit 26f6f2d3 upstream. Since sequence block v2 the second byte contains flags other than just pull up/down. Don't pass arbitrary data to the sideband interface. The rest may or may not work for sequence block v2, but there should be no harm done. Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Jani Nikula authored
commit 4db3a244 upstream. Do not blindly trust the VBT data used for indexing. Reviewed-by:
-
CQ Tang authored
commit fda3bec1 upstream. This is a 32-bit register. Apparently harmless on real hardware, but causing justified warnings in simulation. Signed-off-by:
CQ Tang <cq.tang@intel.com> Signed-off-by:
David Woodhouse <David.Woodhouse@intel.com> Signed-off-by:
-
- 03 Mar, 2016 1 commit
-
-
Luis Henriques authored
This reverts commit 0f7b4f79, which was commit ff4319dc upstream. This commit introduced a regression in this kernel. Commit 95be58df ("firmware: dmi_scan: Use full dmi version for SMBIOS3") added support for SMBIOS3. However, this was not backport to this kernel version, and thus commit ff4319dc should have not been applied. BugLink: https://bugs.launchpad.net/bugs/1551419Signed-off-by:
-
- 02 Mar, 2016 1 commit
-
-
Luis Henriques authored
Signed-off-by:
-
- 29 Feb, 2016 2 commits
-
-
Florian Fainelli authored
commit d5c3d846 upstream. Commit 2c7b4921 ("phy: fix the use of PHY_IGNORE_INTERRUPT") changed a hunk in phy_state_machine() in the PHY_RUNNING case which was not needed. The change essentially makes the PHY library treat PHY devices with PHY_IGNORE_INTERRUPT to keep polling for the PHY device, even though the intent is not to do it. Fix this by reverting that specific hunk, which makes the PHY state machine wait for state changes, and stay in the PHY_RUNNING state for as long as needed. Fixes: 2c7b4921 ("phy: fix the use of PHY_IGNORE_INTERRUPT") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Shaohui Xie authored
commit 11e122cb upstream. Currently, if phy state is PHY_RUNNING, we always register a CHANGE when phy works in polling or interrupt ignored, this will make the adjust_link being called even the phy link did Not changed. checking the phy link to make sure the link did changed before we register a CHANGE, if link did not changed, we do nothing. Signed-off-by:
Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by:
-
- 25 Feb, 2016 5 commits
-
-
Thomas Hellstrom authored
commit 12617971 upstream. A regression introduced when the master ttm lock was split into two. Reported-and-tested-by:
Brian Paul <brianp@vmware.com> Signed-off-by:
Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by:
-
Willy Tarreau authored
commit 759c0114 upstream. On no-so-small systems, it is possible for a single process to cause an OOM condition by filling large pipes with data that are never read. A typical process filling 4000 pipes with 1 MB of data will use 4 GB of memory. On small systems it may be tricky to set the pipe max size to prevent this from happening. This patch makes it possible to enforce a per-user soft limit above which new pipes will be limited to a single page, effectively limiting them to 4 kB each, as well as a hard limit above which no new pipes may be created for this user. This has the effect of protecting the system against memory abuse without hurting other users, and still allowing pipes to work correctly though with less data at once. The limit are controlled by two new sysctls : pipe-user-pages-soft, and pipe-user-pages-hard. Both may be disabled by setting them to zero. The default soft limit allows the default number of FDs per process (1024) to create pipes of the default size (64kB), thus reaching a limit of 64MB before starting to create only smaller pipes. With 256 processes limited to 1024 FDs each, this results in 1024*64kB + (256*1024 - 1024) * 4kB = 1084 MB of memory allocated for a user. The hard limit is disabled by default to avoid breaking existing applications that make intensive use of pipes (eg: for splicing). Reported-by: socketpair@gmail.com Reported-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Mitigates: CVE-2013-4312 (Linux 2.0+) Suggested-by:
Willy Tarreau <w@1wt.eu> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Leon Romanovsky authored
commit 75c1657e upstream. Fix the RC QPs send queue overhead computation to take into account two additional segments in the WQE which are needed for registration operations. The ATOMIC and UMR segments can't coexist together, so chose maximum out of them. The commit 9e65dc37 ("IB/mlx5: Fix RC transport send queue overhead computation") was intended to update RC transport as commit messages states, but added the code to UC transport. Fixes: 9e65dc37 ("IB/mlx5: Fix RC transport send queue overhead computation") Signed-off-by:
Kamal Heib <kamalh@mellanox.com> Signed-off-by:
Leon Romanovsky <leonro@mellanox.com> Reviewed-by:
Sagi Grimberg <sagig@mellanox.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Xin Long authored
commit 7a84bd46 upstream. Commit ed5a377d ("sctp: translate host order to network order when setting a hmacid") corrected the hmacid byte-order when setting a hmacid. but the same issue also exists on getting a hmacid. We fix it by changing hmacids to host order when users get them with getsockopt. Fixes: Commit ed5a377d ("sctp: translate host order to network order when setting a hmacid") Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
-
Eric Dumazet authored
commit 44c3d0c1 upstream. Silence lockdep false positive about rcu_dereference() being used in the wrong context. First one should use rcu_dereference_protected() as we own the spinlock. Second one should be a normal assignation, as no barrier is needed. Fixes: 18367681 ("ipv6 flowlabel: Convert np->ipv6_fl_list to RCU.") Reported-by:
Dave Jones <davej@codemonkey.org.uk> Signed-off-by:
Eric Dumazet <edumazet@google.com> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
