commit c236c8e9 upstream.

While working on the futex code, I stumbled over this potential
use-after-free scenario. Dmitry triggered it later with syzkaller.

pi_mutex is a pointer into pi_state, which we drop the reference on in
unqueue_me_pi(). So any access to that pointer after that is bad.

Since other sites already do rt_mutex_unlock() with hb->lock held, see
for example futex_lock_pi(), simply move the unlock before
unqueue_me_pi().
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Cc: juri.lelli@arm.com
Cc: bigeasy@linutronix.de
Cc: xlpang@redhat.com
Cc: rostedt@goodmis.org
Cc: mathieu.desnoyers@efficios.com
Cc: jdesfossez@efficios.com
Cc: dvhart@infradead.org
Cc: bristot@redhat.com
Link: http://lkml.kernel.org/r/20170304093558.801744246@infradead.orgSigned-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 16681037 upstream.

sdhci_arasan_get_timeout_clock() divides the frequency it has with (1 <<
(13 + divisor)).

However, the divisor is not some Arasan-specific value, but instead is
just the Data Timeout Counter Value from the SDHCI Timeout Control
Register.

Applying it here like this is wrong as the sdhci driver already takes
that value into account when calculating timeouts, and in fact it *sets*
that register value based on how long a timeout is wanted.

Additionally, sdhci core interprets the .get_timeout_clock callback
return value as if it were read from hardware registers, i.e. the unit
should be kHz or MHz depending on SDHCI_TIMEOUT_CLK_UNIT capability bit.
This bit is set at least on the tested Zynq-7000 SoC.

With the tested hardware (SDHCI_TIMEOUT_CLK_UNIT set) this results in
too high a timeout clock rate being reported, causing the core to use
longer-than-needed timeouts. Additionally, on a partitioned MMC
(therefore having erase_group_def bit set) mmc_calc_max_discard()
disables discard support as it looks like controller does not support
the long timeouts needed for that.

Do not apply the extra divisor and return the timeout clock in the
expected unit.

Tested with a Zynq-7000 SoC and a partitioned Toshiba THGBMAG5A1JBAWR
eMMC card.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: e3ec3a3d ("mmc: arasan: Add driver for Arasan SDHCI")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 6e9f44ea upstream.

Add Quectel UC15, UC20, EC21, and EC25.  The EC20 is handled by
qcserial due to a USB VID/PID conflict with an existing Acer
device.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 3243367b upstream.

Some USB 2.0 devices erroneously report millisecond values in
bInterval. The generic config code manages to catch most of them,
but in some cases it's not completely enough.

The case at stake here is a USB 2.0 braille device, which wants to
announce 10ms and thus sets bInterval to 10, but with the USB 2.0
computation that yields to 64ms.  It happens that one can type fast
enough to reach this interval and get the device buffers overflown,
leading to problematic latencies.  The generic config code does not
catch this case because the 64ms is considered a sane enough value.

This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk
to mark devices which actually report milliseconds in bInterval,
and marks Vario Ultra devices as needing it.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 4ce36271 upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.

Note that the dereference happens in the cmd and wait_init_done
callbacks which are called during probe.

Fixes: 1ba47da5 ("uwb: add the i1480 DFU driver")
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit daf229b1 upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.

Note that the dereference happens in the start callback which is called
during probe.

Fixes: de520b8b ("uwb: add HWA radio controller driver")
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 03ace948 upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.

This specifically fixes the NULL-pointer dereference when probing HWA HC
devices.

Fixes: df365423 ("wusb: add the Wire Adapter (WA) core")
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit f259ca3e upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.

Note that the endpoint access that causes the NULL-deref is currently
only used for debugging purposes during probe so the oops only happens
when dynamic debugging is enabled. This means the driver could be
rewritten to continue to accept device with only two endpoints, should
such devices exist.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit b0addd3f upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 45caeaa5 upstream.

As Eric Dumazet pointed out this also needs to be fixed in IPv6.
v2: Contains the IPv6 tcp/Ipv6 dccp patches as well.

We have seen a few incidents lately where a dst_enty has been freed
with a dangling TCP socket reference (sk->sk_dst_cache) pointing to that
dst_entry. If the conditions/timings are right a crash then ensues when the
freed dst_entry is referenced later on. A Common crashing back trace is:

 #8 [] page_fault at ffffffff8163e648
    [exception RIP: __tcp_ack_snd_check+74]
.
.
 #9 [] tcp_rcv_established at ffffffff81580b64
#10 [] tcp_v4_do_rcv at ffffffff8158b54a
#11 [] tcp_v4_rcv at ffffffff8158cd02
#12 [] ip_local_deliver_finish at ffffffff815668f4
#13 [] ip_local_deliver at ffffffff81566bd9
#14 [] ip_rcv_finish at ffffffff8156656d
#15 [] ip_rcv at ffffffff81566f06
#16 [] __netif_receive_skb_core at ffffffff8152b3a2
#17 [] __netif_receive_skb at ffffffff8152b608
#18 [] netif_receive_skb at ffffffff8152b690
#19 [] vmxnet3_rq_rx_complete at ffffffffa015eeaf [vmxnet3]
#20 [] vmxnet3_poll_rx_only at ffffffffa015f32a [vmxnet3]
#21 [] net_rx_action at ffffffff8152bac2
#22 [] __do_softirq at ffffffff81084b4f
#23 [] call_softirq at ffffffff8164845c
#24 [] do_softirq at ffffffff81016fc5
#25 [] irq_exit at ffffffff81084ee5
#26 [] do_IRQ at ffffffff81648ff8

Of course it may happen with other NIC drivers as well.

It's found the freed dst_entry here:

 224 static bool tcp_in_quickack_mode(struct sock *sk)↩
 225 {↩
 226 ▹       const struct inet_connection_sock *icsk = inet_csk(sk);↩
 227 ▹       const struct dst_entry *dst = __sk_dst_get(sk);↩
 228 ↩
 229 ▹       return (dst && dst_metric(dst, RTAX_QUICKACK)) ||↩
 230 ▹       ▹       (icsk->icsk_ack.quick && !icsk->icsk_ack.pingpong);↩
 231 }↩

But there are other backtraces attributed to the same freed dst_entry in
netfilter code as well.

All the vmcores showed 2 significant clues:

- Remote hosts behind the default gateway had always been redirected to a
different gateway. A rtable/dst_entry will be added for that host. Making
more dst_entrys with lower reference counts. Making this more probable.

- All vmcores showed a postitive LockDroppedIcmps value, e.g:

LockDroppedIcmps                  267

A closer look at the tcp_v4_err() handler revealed that do_redirect() will run
regardless of whether user space has the socket locked. This can result in a
race condition where the same dst_entry cached in sk->sk_dst_entry can be
decremented twice for the same socket via:

do_redirect()->__sk_dst_check()-> dst_release().

Which leads to the dst_entry being prematurely freed with another socket
pointing to it via sk->sk_dst_cache and a subsequent crash.

To fix this skip do_redirect() if usespace has the socket locked. Instead let
the redirect take place later when user space does not have the socket
locked.

The dccp/IPv6 code is very similar in this respect, so fixing it there too.

As Eric Garver pointed out the following commit now invalidates routes. Which
can set the dst->obsolete flag so that ipv4_dst_check() returns null and
triggers the dst_release().

Fixes: ceb33206 ("ipv4: Kill routes during PMTU/redirect updates.")
Cc: Eric Garver <egarver@redhat.com>
Cc: Hannes Sowa <hsowa@redhat.com>
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 6e526fdf upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.

The endpoints are specifically dereferenced in the i2400m_bootrom_init
path during probe (e.g. in i2400mu_tx_bulk_out).

Fixes: f398e424 ("i2400m/USB: probe/disconnect, dev init/shutdown
and reset backends")
Cc: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 68c32f9c upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.

Fixes: cf7776dc ("[PATCH] isdn4linux: Siemens Gigaset drivers -
direct USB connection")
Cc: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 67e19400 upstream.

Commit 27596472 ("ipv6: fix ECMP route replacement") introduced a
loop that removes all siblings of an ECMP route that is being
replaced. However, this loop doesn't stop when it has replaced
siblings, and keeps removing other routes with a higher metric.
We also end up triggering the WARN_ON after the loop, because after
this nsiblings < 0.

Instead, stop the loop when we have taken care of all routes with the
same metric as the route being replaced.

  Reproducer:
  ===========
    #!/bin/sh

    ip netns add ns1
    ip netns add ns2
    ip -net ns1 link set lo up

    for x in 0 1 2 ; do
        ip link add veth$x netns ns2 type veth peer name eth$x netns ns1
        ip -net ns1 link set eth$x up
        ip -net ns2 link set veth$x up
    done

    ip -net ns1 -6 r a 2000::/64 nexthop via fe80::0 dev eth0 \
            nexthop via fe80::1 dev eth1 nexthop via fe80::2 dev eth2
    ip -net ns1 -6 r a 2000::/64 via fe80::42 dev eth0 metric 256
    ip -net ns1 -6 r a 2000::/64 via fe80::43 dev eth0 metric 2048

    echo "before replace, 3 routes"
    ip -net ns1 -6 r | grep -v '^fe80\|^ff00'
    echo

    ip -net ns1 -6 r c 2000::/64 nexthop via fe80::4 dev eth0 \
            nexthop via fe80::5 dev eth1 nexthop via fe80::6 dev eth2

    echo "after replace, only 2 routes, metric 2048 is gone"
    ip -net ns1 -6 r | grep -v '^fe80\|^ff00'

Fixes: 27596472 ("ipv6: fix ECMP route replacement")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 366a1569 upstream.

Because nfs4_opendata_access() has close the state when access is denied,
so the state isn't leak.
Rather than revert the commit a974deee, I'd like clean the strange state close.

[ 1615.094218] ------------[ cut here ]------------
[ 1615.094607] WARNING: CPU: 0 PID: 23702 at lib/list_debug.c:31 __list_add_valid+0x8e/0xa0
[ 1615.094913] list_add double add: new=ffff9d7901d9f608, prev=ffff9d7901d9f608, next=ffff9d7901ee8dd0.
[ 1615.095458] Modules linked in: nfsv4(E) nfs(E) nfsd(E) tun bridge stp llc fuse ip_set nfnetlink vmw_vsock_vmci_transport vsock f2fs snd_seq_midi snd_seq_midi_event fscrypto coretemp ppdev crct10dif_pclmul crc32_pclmul ghash_clmulni_intel intel_rapl_perf vmw_balloon snd_ens1371 joydev gameport snd_ac97_codec ac97_bus snd_seq snd_pcm snd_rawmidi snd_timer snd_seq_device snd soundcore nfit parport_pc parport acpi_cpufreq tpm_tis tpm_tis_core tpm i2c_piix4 vmw_vmci shpchp auth_rpcgss nfs_acl lockd(E) grace sunrpc(E) xfs libcrc32c vmwgfx drm_kms_helper ttm drm crc32c_intel mptspi e1000 serio_raw scsi_transport_spi mptscsih mptbase ata_generic pata_acpi fjes [last unloaded: nfs]
[ 1615.097663] CPU: 0 PID: 23702 Comm: fstest Tainted: G        W   E   4.11.0-rc1+ #517
[ 1615.098015] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 07/02/2015
[ 1615.098807] Call Trace:
[ 1615.099183]  dump_stack+0x63/0x86
[ 1615.099578]  __warn+0xcb/0xf0
[ 1615.099967]  warn_slowpath_fmt+0x5f/0x80
[ 1615.100370]  __list_add_valid+0x8e/0xa0
[ 1615.100760]  nfs4_put_state_owner+0x75/0xc0 [nfsv4]
[ 1615.101136]  __nfs4_close+0x109/0x140 [nfsv4]
[ 1615.101524]  nfs4_close_state+0x15/0x20 [nfsv4]
[ 1615.101949]  nfs4_close_context+0x21/0x30 [nfsv4]
[ 1615.102691]  __put_nfs_open_context+0xb8/0x110 [nfs]
[ 1615.103155]  put_nfs_open_context+0x10/0x20 [nfs]
[ 1615.103586]  nfs4_file_open+0x13b/0x260 [nfsv4]
[ 1615.103978]  do_dentry_open+0x20a/0x2f0
[ 1615.104369]  ? nfs4_copy_file_range+0x30/0x30 [nfsv4]
[ 1615.104739]  vfs_open+0x4c/0x70
[ 1615.105106]  ? may_open+0x5a/0x100
[ 1615.105469]  path_openat+0x623/0x1420
[ 1615.105823]  do_filp_open+0x91/0x100
[ 1615.106174]  ? __alloc_fd+0x3f/0x170
[ 1615.106568]  do_sys_open+0x130/0x220
[ 1615.106920]  ? __put_cred+0x3d/0x50
[ 1615.107256]  SyS_open+0x1e/0x20
[ 1615.107588]  entry_SYSCALL_64_fastpath+0x1a/0xa9
[ 1615.107922] RIP: 0033:0x7fab599069b0
[ 1615.108247] RSP: 002b:00007ffcf0600d78 EFLAGS: 00000246 ORIG_RAX: 0000000000000002
[ 1615.108575] RAX: ffffffffffffffda RBX: 00007fab59bcfae0 RCX: 00007fab599069b0
[ 1615.108896] RDX: 0000000000000200 RSI: 0000000000000200 RDI: 00007ffcf060255e
[ 1615.109211] RBP: 0000000000040010 R08: 0000000000000000 R09: 0000000000000016
[ 1615.109515] R10: 00000000000006a1 R11: 0000000000000246 R12: 0000000000041000
[ 1615.109806] R13: 0000000000040010 R14: 0000000000001000 R15: 0000000000002710
[ 1615.110152] ---[ end trace 96ed63b1306bf2f3 ]---

Fixes: a974deee ("NFSv4: Fix memory and state leak in...")
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 80354c29 upstream.

The interrupt line used for the watchdog is 12, according to the official
Intel Edison BSP code.

And indeed after fixing it we start getting an interrupt and thus the
watchdog starts working again:

  [  191.699951] Kernel panic - not syncing: Kernel Watchdog
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 78a3bb9e ("x86: intel-mid: add watchdog platform code for Merrifield")
Link: http://lkml.kernel.org/r/20170312150744.45493-1-andriy.shevchenko@linux.intel.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 89316fa3 upstream.

Make sure clock is enabled for ethtool ops.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: Edwin Chan <edwin.chan@broadcom.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 6be371b0 upstream.

When using the internal PHY it must be powered up when the MII is probed
or the PHY will not be detected.  Since the PHY is powered up at reset
this has not been a problem.  However, when the kernel is restarted with
kexec the PHY will likely be powered down when the kernel starts so it
will not be detected and the Ethernet link will not be established.

This commit explicitly powers up the internal PHY when the GENET driver
is probed to correct this behavior.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 07c52d6a upstream.

Add a spinlock to ensure that irq0_stat is not unintentionally altered
as the result of preemption.  Also removed unserviced irq0 interrupts
and removed irq1_stat since there is no bottom half service for those
interrupts.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16:
 - bcmgenet_irq_task() only handles UMAC_IRQ_LINK_UP and UMAC_IRQ_LINK_DOWN
   status flags
 - Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 1ad3d225 upstream.

The gap between the Tx status counters and the Rx RUNT counters is now
being added to allow correct reporting of the registers.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit ffff7132 upstream.

The location of the RBUF overflow and error counters has moved between
different version of the GENET MAC.  This commit corrects the driver to
read from the correct locations depending on the version of the GENET
MAC.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 4b3b45ed upstream.

commit c146066a ("ipv4: Don't use ufo handling on later transformed
packets") and commit f89c56ce ("ipv6: Don't use ufo handling on
later transformed packets") added a check that 'rt->dst.header_len' isn't
zero in order to skip UFO, but it doesn't include IPcomp in transport mode
where it equals zero.

Packets, after payload compression, may not require further fragmentation,
and if original length exceeds MTU, later compressed packets will be
transmitted incorrectly. This can be reproduced with LTP udp_ipsec.sh test
on veth device with enabled UFO, MTU is 1500 and UDP payload is 2000:

* IPv4 case, offset is wrong + unnecessary fragmentation
    udp_ipsec.sh -p comp -m transport -s 2000 &
    tcpdump -ni ltp_ns_veth2
    ...
    IP (tos 0x0, ttl 64, id 45203, offset 0, flags [+],
      proto Compressed IP (108), length 49)
      10.0.0.2 > 10.0.0.1: IPComp(cpi=0x1000)
    IP (tos 0x0, ttl 64, id 45203, offset 1480, flags [none],
      proto UDP (17), length 21) 10.0.0.2 > 10.0.0.1: ip-proto-17

* IPv6 case, sending small fragments
    udp_ipsec.sh -6 -p comp -m transport -s 2000 &
    tcpdump -ni ltp_ns_veth2
    ...
    IP6 (flowlabel 0x6b9ba, hlim 64, next-header Compressed IP (108)
      payload length: 37) fd00::2 > fd00::1: IPComp(cpi=0x1000)
    IP6 (flowlabel 0x6b9ba, hlim 64, next-header Compressed IP (108)
      payload length: 21) fd00::2 > fd00::1: IPComp(cpi=0x1000)

Fix it by checking 'rt->dst.xfrm' pointer to 'xfrm_state' struct, skip UFO
if xfrm is set. So the new check will include both cases: IPcomp and IPsec.

Fixes: c146066a ("ipv4: Don't use ufo handling on later transformed packets")
Fixes: f89c56ce ("ipv6: Don't use ufo handling on later transformed packets")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 61eb2b43 upstream.

Neil Brown pointed out a potential deadlock in raid 10 code with
bio_split/chain. The raid1 code could have the same issue, but recent
barrier rework makes it less likely to happen. The deadlock happens in
below sequence:

1. generic_make_request(bio), this will set current->bio_list
2. raid10_make_request will split bio to bio1 and bio2
3. __make_request(bio1), wait_barrer, add underlayer disk bio to
current->bio_list
4. __make_request(bio2), wait_barrer

If raise_barrier happens between 3 & 4, since wait_barrier runs at 3,
raise_barrier waits for IO completion from 3. And since raise_barrier
sets barrier, 4 waits for raise_barrier. But IO from 3 can't be
dispatched because raid10_make_request() doesn't finished yet.

The solution is to adjust the IO ordering. Quotes from Neil:
"
It is much safer to:

    if (need to split) {
        split = bio_split(bio, ...)
        bio_chain(...)
        make_request_fn(split);
        generic_make_request(bio);
   } else
        make_request_fn(mddev, bio);

This way we first process the initial section of the bio (in 'split')
which will queue some requests to the underlying devices.  These
requests will be queued in generic_make_request.
Then we queue the remainder of the bio, which will be added to the end
of the generic_make_request queue.
Then we return.
generic_make_request() will pop the lower-level device requests off the
queue and handle them first.  Then it will process the remainder
of the original bio once the first section has been fully processed.
"

Note, this only happens in read path. In write path, the bio is flushed to
underlaying disks either by blk flush (from schedule) or offladed to raid1/10d.
It's queued in current->bio_list.

Cc: Coly Li <colyli@suse.de>
Suggested-by: NeilBrown <neilb@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Shaohua Li <shli@fb.com>
[bwh: For 3.16, drop the raid10 part as advised]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit de46e566 upstream.

Make sure to verify that we have the required interrupt-out endpoint for
IOWarrior56 devices to avoid dereferencing a NULL-pointer in write
should a malicious device lack such an endpoint.

Fixes: 946b960d ("USB: add driver for iowarrior devices.")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 67b0503d upstream.

The buffer allocation for the firmware data was changed in
commit 43fab979 ("[media] dvb-usb: don't use stack for firmware load")
but the same applies for the reset value.

Fixes: 43fab979 ("[media] dvb-usb: don't use stack for firmware load")
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 43fab979 upstream.

As reported by Marc Duponcheel <marc@offline.be>, firmware load on
dvb-usb is using the stack, with is not allowed anymore on default
Kernel configurations:

[ 1025.958836] dvb-usb: found a 'WideView WT-220U PenType Receiver (based on ZL353)' in cold state, will try to load a firmware
[ 1025.958853] dvb-usb: downloading firmware from file 'dvb-usb-wt220u-zl0353-01.fw'
[ 1025.958855] dvb-usb: could not stop the USB controller CPU.
[ 1025.958856] dvb-usb: error while transferring firmware (transferred size: -11, block size: 3)
[ 1025.958856] dvb-usb: firmware download failed at 8 with -22
[ 1025.958867] usbcore: registered new interface driver dvb_usb_dtt200u

[    2.789902] dvb-usb: downloading firmware from file 'dvb-usb-wt220u-zl0353-01.fw'
[    2.789905] ------------[ cut here ]------------
[    2.789911] WARNING: CPU: 3 PID: 2196 at drivers/usb/core/hcd.c:1584 usb_hcd_map_urb_for_dma+0x430/0x560 [usbcore]
[    2.789912] transfer buffer not dma capable
[    2.789912] Modules linked in: btusb dvb_usb_dtt200u(+) dvb_usb_af9035(+) btrtl btbcm dvb_usb dvb_usb_v2 btintel dvb_core bluetooth rc_core rfkill x86_pkg_temp_thermal intel_powerclamp coretemp crc32_pclmul aesni_intel aes_x86_64 glue_helper lrw gf128mul ablk_helper cryptd drm_kms_helper syscopyarea sysfillrect pcspkr i2c_i801 sysimgblt fb_sys_fops drm i2c_smbus i2c_core r8169 lpc_ich mfd_core mii thermal fan rtc_cmos video button acpi_cpufreq processor snd_hda_codec_realtek snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm snd_timer snd crc32c_intel ahci libahci libata xhci_pci ehci_pci xhci_hcd ehci_hcd usbcore usb_common dm_mirror dm_region_hash dm_log dm_mod
[    2.789936] CPU: 3 PID: 2196 Comm: systemd-udevd Not tainted 4.9.0-gentoo #1
[    2.789937] Hardware name: ASUS All Series/H81I-PLUS, BIOS 0401 07/23/2013
[    2.789938]  ffffc9000339b690 ffffffff812bd397 ffffc9000339b6e0 0000000000000000
[    2.789939]  ffffc9000339b6d0 ffffffff81055c86 000006300339b6a0 ffff880116c0c000
[    2.789941]  0000000000000000 0000000000000000 0000000000000001 ffff880116c08000
[    2.789942] Call Trace:
[    2.789945]  [<ffffffff812bd397>] dump_stack+0x4d/0x66
[    2.789947]  [<ffffffff81055c86>] __warn+0xc6/0xe0
[    2.789948]  [<ffffffff81055cea>] warn_slowpath_fmt+0x4a/0x50
[    2.789952]  [<ffffffffa006d460>] usb_hcd_map_urb_for_dma+0x430/0x560 [usbcore]
[    2.789954]  [<ffffffff814ed5a8>] ? io_schedule_timeout+0xd8/0x110
[    2.789956]  [<ffffffffa006e09c>] usb_hcd_submit_urb+0x9c/0x980 [usbcore]
[    2.789958]  [<ffffffff812d0ebf>] ? copy_page_to_iter+0x14f/0x2b0
[    2.789960]  [<ffffffff81126818>] ? pagecache_get_page+0x28/0x240
[    2.789962]  [<ffffffff8118c2a0>] ? touch_atime+0x20/0xa0
[    2.789964]  [<ffffffffa006f7c4>] usb_submit_urb+0x2c4/0x520 [usbcore]
[    2.789967]  [<ffffffffa006feca>] usb_start_wait_urb+0x5a/0xe0 [usbcore]
[    2.789969]  [<ffffffffa007000c>] usb_control_msg+0xbc/0xf0 [usbcore]
[    2.789970]  [<ffffffffa067903d>] usb_cypress_writemem+0x3d/0x40 [dvb_usb]
[    2.789972]  [<ffffffffa06791cf>] usb_cypress_load_firmware+0x4f/0x130 [dvb_usb]
[    2.789973]  [<ffffffff8109dbbe>] ? console_unlock+0x2fe/0x5d0
[    2.789974]  [<ffffffff8109e10c>] ? vprintk_emit+0x27c/0x410
[    2.789975]  [<ffffffff8109e40a>] ? vprintk_default+0x1a/0x20
[    2.789976]  [<ffffffff81124d76>] ? printk+0x43/0x4b
[    2.789977]  [<ffffffffa0679310>] dvb_usb_download_firmware+0x60/0xd0 [dvb_usb]
[    2.789979]  [<ffffffffa0679898>] dvb_usb_device_init+0x3d8/0x610 [dvb_usb]
[    2.789981]  [<ffffffffa069e302>] dtt200u_usb_probe+0x92/0xd0 [dvb_usb_dtt200u]
[    2.789984]  [<ffffffffa007420c>] usb_probe_interface+0xfc/0x270 [usbcore]
[    2.789985]  [<ffffffff8138bf95>] driver_probe_device+0x215/0x2d0
[    2.789986]  [<ffffffff8138c0e6>] __driver_attach+0x96/0xa0
[    2.789987]  [<ffffffff8138c050>] ? driver_probe_device+0x2d0/0x2d0
[    2.789988]  [<ffffffff81389ffb>] bus_for_each_dev+0x5b/0x90
[    2.789989]  [<ffffffff8138b7b9>] driver_attach+0x19/0x20
[    2.789990]  [<ffffffff8138b33c>] bus_add_driver+0x11c/0x220
[    2.789991]  [<ffffffff8138c91b>] driver_register+0x5b/0xd0
[    2.789994]  [<ffffffffa0072f6c>] usb_register_driver+0x7c/0x130 [usbcore]
[    2.789994]  [<ffffffffa06a5000>] ? 0xffffffffa06a5000
[    2.789996]  [<ffffffffa06a501e>] dtt200u_usb_driver_init+0x1e/0x20 [dvb_usb_dtt200u]
[    2.789997]  [<ffffffff81000408>] do_one_initcall+0x38/0x140
[    2.789998]  [<ffffffff8116001c>] ? __vunmap+0x7c/0xc0
[    2.789999]  [<ffffffff81124fb0>] ? do_init_module+0x22/0x1d2
[    2.790000]  [<ffffffff81124fe8>] do_init_module+0x5a/0x1d2
[    2.790002]  [<ffffffff810c96b1>] load_module+0x1e11/0x2580
[    2.790003]  [<ffffffff810c68b0>] ? show_taint+0x30/0x30
[    2.790004]  [<ffffffff81177250>] ? kernel_read_file+0x100/0x190
[    2.790005]  [<ffffffff810c9ffa>] SyS_finit_module+0xba/0xc0
[    2.790007]  [<ffffffff814f13e0>] entry_SYSCALL_64_fastpath+0x13/0x94
[    2.790008] ---[ end trace c78a74e78baec6fc ]---

So, allocate the structure dynamically.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 8c76d7cd upstream.

Add missing sanity check to the bulk-in completion handler to avoid an
integer underflow that could be triggered by a malicious device.

This avoids leaking up to 56 bytes from after the URB transfer buffer to
user space.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 0b1d250a upstream.

Fix a NULL-pointer dereference in the interrupt callback should a
malicious device send data containing a bad port number by adding the
missing sanity check.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 4b5347a2 upstream.

When building for microMIPS we need to ensure that the assembler always
knows that there is code at the target of a branch or jump. Recent
toolchains will fail to link a microMIPS kernel when this isn't the case
due to what it thinks is a branch to non-microMIPS code.

mips-mti-linux-gnu-ld kernel/built-in.o: .spinlock.text+0x2fc: Unsupported branch between ISA modes.
mips-mti-linux-gnu-ld final link failed: Bad value

This is due to inline assembly labels in spinlock.h not being followed
by an instruction mnemonic, either due to a .subsection pseudo-op or the
end of the inline asm block.

Fix this with a .insn direction after such labels.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15325/Signed-off-by: James Hogan <james.hogan@imgtec.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 13603685 upstream.

As reported by Max, the Windows 2008 R2 chkdsk utility expects
VERIFY_16 to be supported, and does not handle the returned
CHECK_CONDITION properly, resulting in an infinite loop.

The kernel will log huge amounts of this error:

kernel: TARGET_CORE[iSCSI]: Unsupported SCSI Opcode 0x8f, sending
CHECK_CONDITION.
Signed-off-by: Max Lohrmann <post@wickenrode.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit a04e54f2 upstream.

The following fixes a divide by zero OOPs with TYPE_TAPE
due to pscsi_tape_read_blocksize() failing causing a zero
sd->sector_size being propigated up via dev_attrib.hw_block_size.

It also fixes another long-standing bug where TYPE_TAPE and
TYPE_MEDIMUM_CHANGER where using pscsi_create_type_other(),
which does not call scsi_device_get() to take the device
reference.  Instead, rename pscsi_create_type_rom() to
pscsi_create_type_nondisk() and use it for all cases.

Finally, also drop a dump_stack() in pscsi_get_blocks() for
non TYPE_DISK, which in modern target-core can get invoked
via target_sense_desc_format() during CHECK_CONDITION.
Reported-by: Malcolm Haak <insanemal@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[bwh: Backported to 3.16:
 - Deleted log format is slightly different
 - Cast Scsi_Host::max_sectors from unsigned short to unsigned int, to avoid
   a warning about differing types in min_not_zero()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 85e8a239 upstream.

We see lpfc devices regularly fail during kexec. Fix this by adding a
shutdown method which mirrors the remove method.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Tested-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 97ee351b upstream.

Recent toolchains force the TOC to be 256 byte aligned. We need to
enforce this alignment in the zImage linker script, otherwise pointers
to our TOC variables (__toc_start) could be incorrect. If the actual
start of the TOC and __toc_start don't have the same value we crash
early in the zImage wrapper.
Suggested-by: Alan Modra <amodra@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 45838660 upstream.

The aux port does not get detected without noloop quirk, so external PS/2
mouse cannot work as result.

The PS/2 mouse can work with this quirk.

BugLink: https://bugs.launchpad.net/bugs/1591053Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit b581a585 upstream.

Since ceph.git commit 4e28f9e63644 ("osd/OSDMap: clear osd_info,
osd_xinfo on osd deletion"), weight is set to IN when OSD is deleted.
This changes the result of applying an incremental for clients, not
just OSDs.  Because CRUSH computations are obviously affected,
pre-4e28f9e63644 servers disagree with post-4e28f9e63644 clients on
object placement, resulting in misdirected requests.

Mirrors ceph.git commit a6009d1039a55e2c77f431662b3d6cc5a8e8e63f.

Fixes: 930c5328 ("libceph: apply new_state before new_up_client on incrementals")
Link: http://tracker.ceph.com/issues/19122Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 934767c5 upstream.

The return status of the adapter check on KERNEL_PANIC is supposed to be
the upper 16 bits of the OMR status register.

Fixes: c421530b (scsi: aacraid: Reorder Adpater status check)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 2e46565c upstream.

A recent change claimed to fix an off-by-one error in the OOB-port
completion handler, but instead introduced such an error. This could
specifically led to modem-status changes going unnoticed, effectively
breaking TIOCMGET.

Note that the offending commit fixes a loop-condition underflow and is
marked for stable, but should not be backported without this fix.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 2d380889 ("USB: serial: digi_acceleport: fix OOB data sanity
check")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 2bfa0719 upstream.

If we're dealing with SuperSpeed endpoints, we need
to make sure to pass along the companion descriptor
and initialize fields needed by the Gadget
API. Eventually, f_fs.c should be converted to use
config_ep_by_speed() like all other functions,
though.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 7369090a upstream.

Some gadget drivers are bad, bad boys. We notice
that ADB was passing bad Burst Size which caused top
bits of param0 to be overwritten which confused DWC3
when running this command.

In order to avoid future issues, we're going to make
sure values passed by macros are always safe for the
controller. Note that ADB still needs a fix to *not*
pass bad values.
Reported-by: Mohamed Abbas <mohamed.abbas@intel.com>
Sugested-by: Adam Andruszak <adam.andruszak@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 0878fff1 upstream.

The Generic PHY driver is a catch-all PHY driver and it should preserve
whatever prior initialization has been done by boot loader or firmware
agents. For specific PHY device configuration it is expected that a
specialized PHY driver would take over that role.

Resetting the generic PHY was a bad idea that has lead to several
complaints and downstream workarounds e.g: in OpenWrt/LEDE so restore
the behavior prior to 87aa9f9c ("net: phy: consolidate PHY
reset in phy_init_hw()").
Reported-by: Felix Fietkau <nbd@nbd.name>
Fixes: 87aa9f9c ("net: phy: consolidate PHY reset in phy_init_hw()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 0c2bf9f9 upstream.

GIC_PPI flags were misconfigured for the timers, resulting in errors
like:
[    0.000000] GIC: PPI11 is secure or misconfigured

Changing them to being edge triggered corrects the issue
Suggested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: d27509f1 ("ARM: BCM5301X: add dts files for BCM4708 SoC")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>