Impact: None (new bit definitions currently unused)

Add bit definitions for the MSR_IA32_MISC_ENABLE MSRs to
<asm/msr-index.h>.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>

Beschorner Daniel reported:
> hwinfo problem since 2.6.28, showing this in the oops:
>	Corrupted page table at address 7fd04de3ec00

Also, PaX Team reported a regression with this commit:

>	commit 9542ada8
>	Author: Suresh Siddha <suresh.b.siddha@intel.com>
>	Date:   Wed Sep 24 08:53:33 2008 -0700
>
>	    x86: track memtype for RAM in page struct

This commit breaks mapping any RAM page through /dev/mem, as the
reserve_memtype() was not initializing the return attribute type and as such
corrupting the PTE entry that was setup with the return attribute type.

Because of this bug, application mapping this RAM page through /dev/mem
will die with "Corrupted page table at address xxxx" message in the kernel
log and also the kernel identity mapping which maps the underlying RAM
page gets converted to UC.

Fix this by initializing the return attribute type before calling
reserve_ram_pages_type()
Reported-by: PaX Team <pageexec@freemail.hu>
Reported-and-tested-by: Beschorner Daniel <Daniel.Beschorner@facton.com>
Tested-and-Acked-by: PaX Team <pageexec@freemail.hu>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

while looking at:

  http://bugzilla.kernel.org/show_bug.cgi?id=11541

I realized that the mtrr.show param cannot work, because
the code is processed much too early.

This patch:
 - Declares mtrr.show as early_param
 - Stays consistent with the previous param (which I doubt
   that it ever worked), so mtrr.show=1 would still work
 - Declares mtrr_show as initdata
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Impact: fix sporadic slowdowns and warning messages

This patch fixes a performance issue reported by Linus on his
Nehalem system. While Linus reverted the PAT patch (commit
58dab916) which exposed the issue,
existing cpa() code can potentially still cause wrong(page attribute
corruption) behavior.

This patch also fixes the "WARNING: at arch/x86/mm/pageattr.c:560" that
various people reported.

In 64bit kernel, kernel identity mapping might have holes depending
on the available memory and how e820 reports the address range
covering the RAM, ACPI, PCI reserved regions. If there is a 2MB/1GB hole
in the address range that is not listed by e820 entries, kernel identity
mapping will have a corresponding hole in its 1-1 identity mapping.

If cpa() happens on the kernel identity mapping which falls into these holes,
existing code fails like this:

	__change_page_attr_set_clr()
		__change_page_attr()
			returns 0 because of if (!kpte). But doesn't
			set cpa->numpages and cpa->pfn.
		cpa_process_alias()
			uses uninitialized cpa->pfn (random value)
			which can potentially lead to changing the page
			attribute of kernel text/data, kernel identity
			mapping of RAM pages etc. oops!

This bug was easily exposed by another PAT patch which was doing
cpa() more often on kernel identity mapping holes (physical range between
max_low_pfn_mapped and 4GB), where in here it was setting the
cache disable attribute(PCD) for kernel identity mappings aswell.

Fix cpa() to handle the kernel identity mapping holes. Retain
the WARN() for cpa() calls to other not present address ranges
(kernel-text/data, ioremap() addresses)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

This reverts commit 4217458d.

Justin Madru bisected this commit, it was causing weird Firefox
crashes.

The reason is that GCC mis-optimizes (re-uses) the on-stack parameters of
the calling frame, which corrupts the syscall return pt_regs state and
thus corrupts user-space register state.

So we go back to the slightly less clean but more optimization-safe
method of getting to pt_regs. Also add a comment to explain this.

Resolves: http://bugzilla.kernel.org/show_bug.cgi?id=12505Reported-and-bisected-by: Justin Madru <jdm64@gawab.com>
Tested-by: Justin Madru <jdm64@gawab.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Impact: fix rare (but currently harmless) miscompile with certain configs and gcc versions

Hugh Dickins noticed that strncpy_from_user() was miscompiled
in some circumstances with gcc 4.3.

Thanks to Hugh's excellent analysis it was easy to track down.

Hugh writes:

> Try building an x86_64 defconfig 2.6.29-rc1 kernel tree,
> except not quite defconfig, switch CONFIG_PREEMPT_NONE=y
> and CONFIG_PREEMPT_VOLUNTARY off (because it expands a
> might_fault() there, which hides the issue): using a
> gcc 4.3.2 (I've checked both openSUSE 11.1 and Fedora 10).
>
> It generates the following:
>
> 0000000000000000 <__strncpy_from_user>:
>    0:   48 89 d1                mov    %rdx,%rcx
>    3:   48 85 c9                test   %rcx,%rcx
>    6:   74 0e                   je     16 <__strncpy_from_user+0x16>
>    8:   ac                      lods   %ds:(%rsi),%al
>    9:   aa                      stos   %al,%es:(%rdi)
>    a:   84 c0                   test   %al,%al
>    c:   74 05                   je     13 <__strncpy_from_user+0x13>
>    e:   48 ff c9                dec    %rcx
>   11:   75 f5                   jne    8 <__strncpy_from_user+0x8>
>   13:   48 29 c9                sub    %rcx,%rcx
>   16:   48 89 c8                mov    %rcx,%rax
>   19:   c3                      retq
>
> Observe that "sub %rcx,%rcx; mov %rcx,%rax", whereas gcc 4.2.1
> (and many other configs) say "sub %rcx,%rdx; mov %rdx,%rax".
> Isn't it returning 0 when it ought to be returning strlen?

The asm constraints for the strncpy_from_user() result were missing an
early clobber, which tells gcc that the last output arguments
are written before all input arguments are read.

Also add more early clobbers in the rest of the file and fix 32-bit
usercopy.c in the same way.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
[ since this API is rarely used and no in-kernel user relies on a 'len'
  return value (they only rely on negative return values) this miscompile
  was never noticed in the field. But it's worth fixing it nevertheless. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Impact: fix crash with memory hotplug enabled

kernel_physical_mapping_init() is called during memory hotplug
so it does not belong in the init section.

If the kernel is built with CONFIG_DEBUG_SECTION_MISMATCH=y on
the make command line, arch/x86/mm/init_64.c is compiled with
the -fno-inline-functions-called-once gcc option defeating
inlining of kernel_physical_mapping_init() within init_memory_mapping().

When kernel_physical_mapping_init() is not inlined it is placed
in the .init.text section according to the __init in it's current
declaration.  A later call to kernel_physical_mapping_init() during
a memory hotplug operation encounters an int3 trap because the
.init.text section memory has been freed.

This patch eliminates the crash caused by the int3 trap by moving the
non-inlined kernel_physical_mapping_init() from .init.text to .meminit.text.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

-tip testing found this crash:

> [   35.258515] calling  acpi_cpufreq_init+0x0/0x127 @ 1
> [   35.264127] BUG: unable to handle kernel NULL pointer dereference at (null)
> [   35.267554] IP: [<ffffffff80478092>] __bitmap_intersects+0x48/0x73
> [   35.267554] PGD 0
> [   35.267554] Oops: 0000 [#1] SMP DEBUG_PAGEALLOC

arch/x86/kernel/cpu/cpufreq/acpi-cpufreq.c is still broken: there's no
allocation of the variable mask, so we pass in an uninitialized cmd.mask
field to drv_read(), which then passes it to the scheduler which then
crashes ...

Switch it over to the much simpler constant-cpumask-pointers approach.
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Impact: use new work_on_cpu function to reduce stack usage

Replace the saving of current->cpus_allowed and set_cpus_allowed_ptr() with
a work_on_cpu function for drv_read() and drv_write().

Basically converts do_drv_{read,write} into "work_on_cpu" functions that
are now called by drv_read and drv_write.

Note: This patch basically reverts 50c668d6 which reverted 7503bfba, now
that the work_on_cpu() function is more stable.
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Tested-by: Dieter Ries <clip2@gmx.de>
Tested-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Cc: Dave Jones <davej@redhat.com>
Cc: <cpufreq@vger.kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Impact: remove potential clashes with generic kevent workqueue

Annoyingly, some places we want to use work_on_cpu are already in
workqueues.  As per Ingo's suggestion, we create a different workqueue
for work_on_cpu.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Impact: remove potential circular lock dependency with cpu hotplug lock

This has caused more problems than it solved, with a pile of cpu
hotplug locking issues.

Followup patches will get_online_cpus() in callers that need it, but
if they don't do it they're no worse than before when they were using
set_cpus_allowed without locking.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

The function setup_cpu_local_masks() has been marked __init, in
order to remove the following section mismatch messages:

WARNING: vmlinux.o(.text+0x3c2c7): Section mismatch in reference from the function setup_cpu_local_masks() to the function .init.text:alloc_bootmem_cpumask_var()
The function setup_cpu_local_masks() references
the function __init alloc_bootmem_cpumask_var().
This is often because setup_cpu_local_masks lacks a __init
annotation or the annotation of alloc_bootmem_cpumask_var is wrong.

WARNING: vmlinux.o(.text+0x3c2d3): Section mismatch in reference from the function setup_cpu_local_masks() to the function .init.text:alloc_bootmem_cpumask_var()
The function setup_cpu_local_masks() references
the function __init alloc_bootmem_cpumask_var().
This is often because setup_cpu_local_masks lacks a __init
annotation or the annotation of alloc_bootmem_cpumask_var is wrong.

WARNING: vmlinux.o(.text+0x3c2df): Section mismatch in reference from the function setup_cpu_local_masks() to the function .init.text:alloc_bootmem_cpumask_var()
The function setup_cpu_local_masks() references
the function __init alloc_bootmem_cpumask_var().
This is often because setup_cpu_local_masks lacks a __init
annotation or the annotation of alloc_bootmem_cpumask_var is wrong.

WARNING: vmlinux.o(.text+0x3c2eb): Section mismatch in reference from the function setup_cpu_local_masks() to the function .init.text:alloc_bootmem_cpumask_var()
The function setup_cpu_local_masks() references
the function __init alloc_bootmem_cpumask_var().
This is often because setup_cpu_local_masks lacks a __init
annotation or the annotation of alloc_bootmem_cpumask_var is wrong.
Signed-off-by: Leonardo Potenza <lpotenza@inwind.it>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Impact: add debug warning

Fire off one message if two apic's discovered with different
apic versions. (this code is only called during CPU init)

The goal of this is to pave the way of the removal of the apic_version[]
array. We dont expect any apic version incompatibilities in the x86
landscape of systems [if so we dont handle them very well and probably
never will handle deep apic version assymetries well], but it's prudent
to have a debug check for one kernel cycle nevertheless.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Commit da4276b8 changed a dependency
for FRAME_POINTER from X86 to ARCH_WANT_FRAME_POINTERS, but didn't
actually define it.

This patch adds the definition for ARCH_WANT_FRAME_POINTERS. Without it,
FRAME_POINTER can't be enabled on x86.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Debugging and original patch from Nick Piggin <npiggin@suse.de>

The early fixmap pmd entry inserted at the very top of the KVA is causing the
subsequent fixmap mapping code to not provide physically linear pte pages over
the kmap atomic portion of the fixmap (which relies on said property to
calculate pte addresses).

This has caused weird boot failures in kmap_atomic much later in the boot
process (initial userspace faults) on a 32-bit PAE system with a larger number
of CPUs (smaller CPU counts tend not to run over into the next page so don't
show up the problem).

Solve this by attempting to clear out the page table, and copy any of its
entries to the new one. Also, add a bug if a nonlinear condition is encountered
and can't be resolved, which might save some hours of debugging if this fragile
scheme ever breaks again...

Once we have such logic, we can also use it to eliminate the early ioremap
trickery around the page table setup for the fixmap area. This also fixes
potential issues with FIX_* entries sharing the leaf page table with the early
ioremap ones getting discarded by early_ioremap_clear() and not restored by
early_ioremap_reset(). It at once eliminates the temporary (and configuration,
namely NR_CPUS, dependent) unavailability of early fixed mappings during the
time the fixmap area page tables get constructed.

Finally, also replace the hard coded calculation of the initial table space
needed for the fixmap area with a proper one, allowing kernels configured for
large CPU counts to actually boot.

Based-on: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

The function uv_wait_completion() spins on reads of a memory-mapped
register, waiting for completion of BAU hardware replies.

It should call "cpu_relax()" between those reads to improve performance
on hyperthreaded configurations.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Acked-by: Jack Steiner <steiner@sgi.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

E.g. when called due to an early panic.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Thierry Vignaud reported:
> http://bugzilla.kernel.org/show_bug.cgi?id=12372
>
> On P4 with an SiS motherboard (video card is a SiS 651)
> X server fails to start with error:
> xf86MapVidMem: Could not mmap framebuffer (0x00000000,0x2000) (Invalid
> argument)

Here X is trying to map first 8KB of memory using /dev/mem. Existing
code treats first 0-4KB of memory as non-RAM and 4KB-8KB as RAM. Recent
code changes don't allow to map memory with different attributes
at the same time.

Fix this by treating the first 1MB legacy region as special and always
track the attribute requests with in this region using linear linked
list (and don't bother if the range is RAM or non-RAM or mixed)
Reported-and-tested-by: Thierry Vignaud <tvignaud@mandriva.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Impact: reduce kernel image size

Hugh Dickins noticed that older gcc versions when the kernel
is built for code size didn't inline some of the bitops.

Mark all complex x86 bitops that have more than a single
asm statement or two as always inline to avoid this problem.

Probably should be done for other architectures too.

Ingo then found a better fix that only requires
a single line change, but it unfortunately only
works on gcc 4.3.

On older gccs the original patch still makes a ~0.3% defconfig
difference with CONFIG_OPTIMIZE_INLINING=y.

With gcc 4.1 and a defconfig like build:

    61169987 1138540  883788 8139326  7c323e vmlinux-oi-with-patch
    6137043 1138540  883788 8159371  7c808b vmlinux-optimize-inlining

~20k / 0.3% difference.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Impact: fix potential boot crash on MAXSMP

Remove code left over by:

  50c668d6: Revert "cpumask: use work_on_cpu in acpi-cpufreq.c for drv_read

That cmd.cpumask is not allocated anymore. No impact on default !MAXSMP
kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>

This reverts commit e0c73175.

This patch was wrong, as lockdep (and thus the irq state tracer)
aren't nmi safe. People are already seeing lockdep warnings due
to this.
Signed-off-by: Ingo Molnar <mingo@elte.hu>

This reverts commit 7503bfba.

Dieter Ries reported bootup soft-hangs and bisected it back to
this commit, and reverting this commit gave him a working system.

The commit introduces work_on_cpu() use into the cpufreq code,
but that is subtly problematic from a lock hierarchy POV: the
hotplug-cpu lock is an highlevel lock that is taken before
lowlevel locks, and in this codepath we are called with the
policy lock taken.

Dieter did not have lockdep enabled so we dont have a nice stack
trace proof for this, but using work_on_cpu() in such a lowlevel
place certainly looks wrong, so we revert the patch.

work_on_cpu() needs to be reworked to be more generally usable.
Reported-by: Dieter Ries <clip2@gmx.de>
Tested-by: Dieter Ries <clip2@gmx.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Fix this by reintroducing asm/smp.h include in apic.c - later on
I will fix this by removing non-smp data from smp.h

Also fix the __inquire_remote_apic() prototype/inline.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Fix this by reintroducing asm/smp.h include in mpparse.c - later on
I will fix this by removing non-smp data from smp.h.
Reported-by: Petr Titera <P.Titera@century.cz>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Ajith Kumar noticed:

 I was going through the vmalloc fault handling for x86_64 and am unclear
 about the following lines in the vmalloc_fault() function.

 pgd = pgd_offset(current->mm ?: &init_mm, address);
 pgd_ref = pgd_offset_k(address);

 Here the intention is to get the pgd corresponding to the current process
 and sync it up with the pgd in init_mm(obtained from pgd_offset_k).
 However, for kernel threads current->mm is NULL and hence pgd =
 pgd_offset(init_mm, address) = pgd_ref which means the fault handler
 returns without setting the pgd entry in the MM structure in the context
 of which the kernel thread has faulted.  This could lead to never-ending
 faults and busy looping of kernel threads like pdflush.  So, shouldn't the
 pgd = pgd_offset(current->mm ?: &init_mm, address); be pgd =
 pgd_offset(current->active_mm ?: &init_mm, address);

We can use active_mm unconditionally because it should be always set.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

It is useful for diagnosing boot performance to see where async function
calls are waiting on serialization...  this patch adds this
functionality to the bootgraph.pl script.

The waiting time is shown as a half transparent, gray bar through the
block that is waiting.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In a discussio with Jeff Garzik, he mentioned that the serialization
for the libata port probes only needs to be within the domain of a host.
This means that for the first port of each host (with ID 0), we don't
need to wait, so we can relax our serialization a little.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch adds a per host flag that allows drivers to opt in into
having its busses scanned in parallel.

Drivers that do not set this flag get their ports scanned in
the "original" sequence.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (36 commits)
  x86: fix section mismatch warnings in mcheck/mce_amd_64.c
  x86: offer frame pointers in all build modes
  x86: remove duplicated #include's
  x86: k8 numa register active regions later
  x86: update Alan Cox's email addresses
  x86: rename all fields of mpc_table mpc_X to X
  x86: rename all fields of mpc_oemtable oem_X to X
  x86: rename all fields of mpc_bus mpc_X to X
  x86: rename all fields of mpc_cpu mpc_X to X
  x86: rename all fields of mpc_intsrc mpc_X to X
  x86: rename all fields of mpc_lintsrc mpc_X to X
  x86: rename all fields of mpc_iopic mpc_X to X
  x86: irqinit_64.c init_ISA_irqs should be static
  Documentation/x86/boot.txt: payload length was changed to payload_length
  x86: setup_percpu.c fix style problems
  x86: irqinit_64.c fix style problems
  x86: irqinit_32.c fix style problems
  x86: i8259.c fix style problems
  x86: irq_32.c fix style problems
  x86: ioport.c fix style problems
  ...

Merge branch 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  [IA64] fix typo in cpumask_of_pcibus()
  x86: fix x86_32 builds for summit and es7000 arch's
  cpumask: use work_on_cpu in acpi-cpufreq.c for read_measured_perf_ctrs
  cpumask: use work_on_cpu in acpi-cpufreq.c for drv_read and drv_write
  cpumask: use cpumask_var_t in acpi-cpufreq.c
  cpumask: use work_on_cpu in acpi/cstate.c
  cpumask: convert struct cpufreq_policy to cpumask_var_t
  cpumask: replace CPUMASK_ALLOC etc with cpumask_var_t
  x86: cleanup remaining cpumask_t ops in smpboot code
  cpumask: update pci_bus_show_cpuaffinity to use new cpumask API
  cpumask: update local_cpus_show to use new cpumask API
  ia64: cpumask fix for is_affinity_mask_valid()

Commit c4be0c1d added the ability for
write_super_lockfs to return errors, and renamed them to match.  But
btrfs didn't get converted.

Do the minimal conversion to make it compile again.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The 'rb_first()', 'rb_last()', 'rb_next()' and 'rb_prev()' calls
take a pointer to an RB node or RB root. They do not change the
pointed objects, so add a 'const' qualifier in order to make life
of the users of these functions easier.

Indeed, if I have my own constant pointer &const struct my_type *p,
and I call 'rb_next(&p->rb)', I get a GCC warning:

warning: passing argument 1 of ‘rb_next’ discards qualifiers from pointer target type
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The sensor can be accessed via various buses.  In particular, SPI, I²C
and, on HP laptops, via a specific ACPI API (the only one currently
supported).  Separate this latest platform from the core of the sensor
driver to allow support for the other bus type.  The second, and more
direct goal is actually to be able to merge this part with the
hp-disk-leds driver, which has the same ACPI PNP number.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It removes XFS specific ioctl interfaces and request codes
for freeze feature.

This patch has been supplied by David Chinner.
Signed-off-by: Dave Chinner <dgc@sgi.com>
Signed-off-by: Takashi Sato <t-sato@yk.jp.nec.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: <xfs-masters@oss.sgi.com>
Cc: <linux-ext4@vger.kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The ioctls for the generic freeze feature are below.
o Freeze the filesystem
  int ioctl(int fd, int FIFREEZE, arg)
    fd: The file descriptor of the mountpoint
    FIFREEZE: request code for the freeze
    arg: Ignored
    Return value: 0 if the operation succeeds. Otherwise, -1

o Unfreeze the filesystem
  int ioctl(int fd, int FITHAW, arg)
    fd: The file descriptor of the mountpoint
    FITHAW: request code for unfreeze
    arg: Ignored
    Return value: 0 if the operation succeeds. Otherwise, -1
    Error number: If the filesystem has already been unfrozen,
                  errno is set to EINVAL.

[akpm@linux-foundation.org: fix CONFIG_BLOCK=n]
Signed-off-by: Takashi Sato <t-sato@yk.jp.nec.com>
Signed-off-by: Masayuki Hamaguchi <m-hamaguchi@ys.jp.nec.com>
Cc: <xfs-masters@oss.sgi.com>
Cc: <linux-ext4@vger.kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently, ext3 in mainline Linux doesn't have the freeze feature which
suspends write requests.  So, we cannot take a backup which keeps the
filesystem's consistency with the storage device's features (snapshot and
replication) while it is mounted.

In many case, a commercial filesystem (e.g.  VxFS) has the freeze feature
and it would be used to get the consistent backup.

If Linux's standard filesystem ext3 has the freeze feature, we can do it
without a commercial filesystem.

So I have implemented the ioctls of the freeze feature.
I think we can take the consistent backup with the following steps.
1. Freeze the filesystem with the freeze ioctl.
2. Separate the replication volume or create the snapshot
   with the storage device's feature.
3. Unfreeze the filesystem with the unfreeze ioctl.
4. Take the backup from the separated replication volume
   or the snapshot.

This patch:

VFS:
Changed the type of write_super_lockfs and unlockfs from "void"
to "int" so that they can return an error.
Rename write_super_lockfs and unlockfs of the super block operation
freeze_fs and unfreeze_fs to avoid a confusion.

ext3, ext4, xfs, gfs2, jfs:
Changed the type of write_super_lockfs and unlockfs from "void"
to "int" so that write_super_lockfs returns an error if needed,
and unlockfs always returns 0.

reiserfs:
Changed the type of write_super_lockfs and unlockfs from "void"
to "int" so that they always return 0 (success) to keep a current behavior.
Signed-off-by: Takashi Sato <t-sato@yk.jp.nec.com>
Signed-off-by: Masayuki Hamaguchi <m-hamaguchi@ys.jp.nec.com>
Cc: <xfs-masters@oss.sgi.com>
Cc: <linux-ext4@vger.kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The code was shifting the endianness appropriately everywhere, annotate
the structs to avoid the sparse warnings when assigning the endian types
to the struct members, or passing them to be[16|32]_to_cpu:

drivers/memstick/core/mspro_block.c:331:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:333:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:335:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:337:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:341:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:347:4: warning: cast to restricted __be32
drivers/memstick/core/mspro_block.c:356:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:358:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:364:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:367:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:369:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:371:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:377:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:478:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:480:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:482:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:484:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:486:4: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:689:22:    expected unsigned int [unsigned] [assigned] data_address
drivers/memstick/core/mspro_block.c:689:22:    got restricted __be32 [usertype] <noident>
drivers/memstick/core/mspro_block.c:697:3: warning: cast to restricted __be32
drivers/memstick/core/mspro_block.c:960:17: warning: incorrect type in initializer (different base types)
drivers/memstick/core/mspro_block.c:960:17:    expected unsigned short [unsigned] data_count
drivers/memstick/core/mspro_block.c:960:17:    got restricted __be16 [usertype] <noident>
drivers/memstick/core/mspro_block.c:993:6: warning: cast to restricted __be16
drivers/memstick/core/mspro_block.c:995:28: warning: cast to restricted __be16
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Compilation of the HP WMI hotkeys code results in the following:

  CC [M]  drivers/platform/x86/hp-wmi.o
drivers/platform/x86/hp-wmi.c: In function hp_wmi_bios_setup:
drivers/platform/x86/hp-wmi.c:431: warning: ignoring return value of rfkill_register,
	 declared with attribute warn_unused_result
drivers/platform/x86/hp-wmi.c:441: warning: ignoring return value of rfkill_register,
	 declared with attribute warn_unused_result
drivers/platform/x86/hp-wmi.c:450: warning: ignoring return value of rfkill_register,
	 declared with attribute warn_unused_result
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>