For Scalable MCA enabled processors, errors are listed per IP block. And
since it is not required for an IP to map to a particular bank, we need
to use HWID and McaType values from the MCx_IPID register to figure out
which IP a given bank represents.

We also have a new bit (TCC) in the MCx_STATUS register to indicate Task
context is corrupt.

Add logic here to decode errors from all known IP blocks for Fam17h
Model 00-0fh and to print TCC errors.

[ Minor fixups. ]
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1457021458-2522-3-git-send-email-Aravind.Gopalakrishnan@amd.comSigned-off-by: Ingo Molnar <mingo@kernel.org>

Those MSRs are used only by the MCE code so move them there.
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1456785179-14378-2-git-send-email-Aravind.Gopalakrishnan@amd.comSigned-off-by: Ingo Molnar <mingo@kernel.org>

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Pull networking fixes from David Miller:

 1) Fix ordering of WEXT netlink messages so we don't see a newlink
    after a dellink, from Johannes Berg.

 2) Out of bounds access in minstrel_ht_set_best_prob_rage, from
    Konstantin Khlebnikov.

 3) Paging buffer memory leak in iwlwifi, from Matti Gottlieb.

 4) Wrong units used to set initial TCP rto from cached metrics, also
    from Konstantin Khlebnikov.

 5) Fix stale IP options data in the SKB control block from leaking
    through layers of encapsulation, from Bernie Harris.

 6) Zero padding len miscalculated in bnxt_en, from Michael Chan.

 7) Only CHECKSUM_PARTIAL packets should be passed down through GSO, fix
    from Hannes Frederic Sowa.

 8) Fix suspend/resume with JME networking devices, from Diego Violat
    and Guo-Fu Tseng.

 9) Checksums not validated properly in bridge multicast support due to
    the placement of the SKB header pointers at the time of the check,
    fix from Álvaro Fernández Rojas.

10) Fix hang/tiemout with r8169 if a stats fetch is done while the
    device is runtime suspended.  From Chun-Hao Lin.

11) The forwarding database netlink dump facilities don't track the
    state of the dump properly, resulting in skipped/missed entries.
    From Minoura Makoto.

12) Fix regression from a recent 3c59x bug fix, from Neil Horman.

13) Fix list corruption in bna driver, from Ivan Vecera.

14) Big endian machines crash on vlan add in bnx2x, fix from Michal
    Schmidt.

15) Ethtool RSS configuration not propagated properly in mlx5 driver,
    from Tariq Toukan.

16) Fix regression in PHY probing in stmmac driver, from Gabriel
    Fernandez.

17) Fix SKB tailroom calculation in igmp/mld code, from Benjamin
    Poirier.

18) A past change to skip empty routing headers in ipv6 extention header
    parsing accidently caused fragment headers to not be matched any
    longer.  Fix from Florian Westphal.

19) eTSEC-106 erratum needs to be applied to more gianfar chips, from
    Atsushi Nemoto.

20) Fix netdev reference after free via workqueues in usb networking
    drivers, from Oliver Neukum and Bjørn Mork.

21) mdio->irq is now an array rather than a pointer to dynamic memory,
    but several drivers were still trying to free it :-/ Fixes from
    Colin Ian King.

22) act_ipt iptables action forgets to set the family field, thus LOG
    netfilter targets don't work with it.  Fix from Phil Sutter.

23) SKB leak in ibmveth when skb_linearize() fails, from Thomas Falcon.

24) pskb_may_pull() cannot be called with interrupts disabled, fix code
    that tries to do this in vmxnet3 driver, from Neil Horman.

25) be2net driver leaks iomap'd memory on removal, fix from Douglas
    Miller.

26) Forgotton RTNL mutex unlock in ppp_create_interface() error paths,
    from Guillaume Nault.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (97 commits)
  ppp: release rtnl mutex when interface creation fails
  cdc_ncm: do not call usbnet_link_change from cdc_ncm_bind
  tcp: fix tcpi_segs_in after connection establishment
  net: hns: fix the bug about loopback
  jme: Fix device PM wakeup API usage
  jme: Do not enable NIC WoL functions on S0
  udp6: fix UDP/IPv6 encap resubmit path
  be2net: Don't leak iomapped memory on removal.
  vmxnet3: avoid calling pskb_may_pull with interrupts disabled
  net: ethernet: Add missing MFD_SYSCON dependency on HAS_IOMEM
  ibmveth: check return of skb_linearize in ibmveth_start_xmit
  cdc_ncm: toggle altsetting to force reset before setup
  usbnet: cleanup after bind() in probe()
  mlxsw: pci: Correctly determine if descriptor queue is full
  mlxsw: spectrum: Always decrement bridge's ref count
  tipc: fix nullptr crash during subscription cancel
  net: eth: altera: do not free array priv->mdio->irq
  net/ethoc: do not free array priv->mdio->irq
  net: sched: fix act_ipt for LOG target
  asix: do not free array priv->mdio->irq
  ...

Pull overlayfs fixes from Miklos Szeredi:
 "Overlayfs bug fixes.  All marked as -stable material"

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: copy new uid/gid into overlayfs runtime inode
  ovl: ignore lower entries when checking purity of non-directory entries
  ovl: fix getcwd() failure after unsuccessful rmdir
  ovl: fix working on distributed fs as lower layer

This reverts commit dbb17a21.

It turns out that commit can cause problems for systems with multiple
GPUs, and causes X to hang on at least a HP Pavilion dv7 with hybrid
graphics.

This got noticed originally in 4.4.4, where this patch had already
gotten back-ported, but 4.5-rc7 was verified to have the same problem.

Alexander Deucher says:
 "It looks like you have a muxed system so I suspect what's happening is
  that one of the display is being reported as connected for both the
  IGP and the dGPU and then the desktop environment gets confused or
  there some sort problem in the detect functions since the mux is not
  switched to the dGPU.  I don't see an easy fix unless Dave has any
  ideas.  I'd say just revert for now"
Reported-by: Jörg-Volker Peetz <jvpeetz@web.de>
Acked-by: Alexander Deucher <Alexander.Deucher@amd.com>
Cc: Dave Airlie <airlied@gmail.com>
Cc: stable@kernel.org  # wherever dbb17a21 got back-ported
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add missing rtnl_unlock() in the error path of ppp_create_interface().

Fixes: 58a89eca ("ppp: fix lockdep splat in ppp_dev_uninit()")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

usbnet_link_change will call schedule_work and should be
avoided if bind is failing. Otherwise we will end up with
scheduled work referring to a netdev which has gone away.

Instead of making the call conditional, we can just defer
it to usbnet_probe, using the driver_info flag made for
this purpose.

Fixes: 8a34b0ae ("usbnet: cdc_ncm: apply usbnet_link_change")
Reported-by: Andrey Konovalov <andreyknvl@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

If final packet (ACK) of 3WHS is lost, it appears we do not properly
account the following incoming segment into tcpi_segs_in

While we are at it, starts segs_in with one, to count the SYN packet.

We do not yet count number of SYN we received for a request sock, we
might add this someday.

packetdrill script showing proper behavior after fix :

// Tests tcpi_segs_in when 3rd packet (ACK) of 3WHS is lost
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
   +0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
   +0 bind(3, ..., ...) = 0
   +0 listen(3, 1) = 0

   +0 < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop>
   +0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK>
+.020 < P. 1:1001(1000) ack 1 win 32792

   +0 accept(3, ..., ...) = 4

+.000 %{ assert tcpi_segs_in == 2, 'tcpi_segs_in=%d' % tcpi_segs_in }%

Fixes: 2efd055c ("tcp: add tcpi_segs_in and tcpi_segs_out to tcp_info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It will always be passed if the soc is tested the loopback cases. This
patch will fix this bug.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to Documentation/power/devices.txt

The driver should not use device_set_wakeup_enable() which is the policy
for user to decide.

Using device_init_wakeup() to initialize dev->power.should_wakeup and
dev->power.can_wakeup on driver initialization.

And use device_may_wakeup() on suspend to decide if WoL function should
be enabled on NIC.
Reported-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Otherwise it might be back on resume right after going to suspend in
some hardware.
Reported-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPv4 interprets a negative return value from a protocol handler as a
request to redispatch to a new protocol.  In contrast, IPv6 interprets a
negative value as an error, and interprets a positive value as a request
for redispatch.

UDP for IPv6 was unaware of this difference.  Change __udp6_lib_rcv() to
return a positive value for redispatch.  Note that the socket's
encap_rcv hook still needs to return a negative value to request
dispatch, and in the case of IPv6 packets, adjust IP6CB(skb)->nhoff to
identify the byte containing the next protocol.
Signed-off-by: Bill Sommerfeld <wsommerfeld@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The adapter->pcicfg resource is either mapped via pci_iomap() or
derived from adapter->db. During be_remove() this resource was ignored
and so could remain mapped after remove.

Add a flag to track whether adapter->pcicfg was mapped or not, then
use that flag in be_unmap_pci_bars() to unmap if required.

Fixes: 25848c90 ("use PCI MMIO read instead of config read for errors")
Signed-off-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3 has a function vmxnet3_parse_and_copy_hdr which, among other operations,
uses pskb_may_pull to linearize the header portion of an skb.  That operation
eventually uses local_bh_disable/enable to ensure that it doesn't race with the
drivers bottom half handler.  Unfortunately, vmxnet3 preforms this
parse_and_copy operation with a spinlock held and interrupts disabled.  This
causes us to run afoul of the WARN_ON_ONCE(irqs_disabled()) warning in
local_bh_enable, resulting in this:

WARNING: at kernel/softirq.c:159 local_bh_enable+0x59/0x90() (Not tainted)
Hardware name: VMware Virtual Platform
Modules linked in: ipv6 ppdev parport_pc parport microcode e1000 vmware_balloon
vmxnet3 i2c_piix4 sg ext4 jbd2 mbcache sd_mod crc_t10dif sr_mod cdrom mptspi
mptscsih mptbase scsi_transport_spi pata_acpi ata_generic ata_piix vmwgfx ttm
drm_kms_helper drm i2c_core dm_mirror dm_region_hash dm_log dm_mod [last
unloaded: mperf]
Pid: 6229, comm: sshd Not tainted 2.6.32-616.el6.i686 #1
Call Trace:
 [<c04624d9>] ? warn_slowpath_common+0x89/0xe0
 [<c0469e99>] ? local_bh_enable+0x59/0x90
 [<c046254b>] ? warn_slowpath_null+0x1b/0x20
 [<c0469e99>] ? local_bh_enable+0x59/0x90
 [<c07bb936>] ? skb_copy_bits+0x126/0x210
 [<f8d1d9fe>] ? ext4_ext_find_extent+0x24e/0x2d0 [ext4]
 [<c07bc49e>] ? __pskb_pull_tail+0x6e/0x2b0
 [<f95a6164>] ? vmxnet3_xmit_frame+0xba4/0xef0 [vmxnet3]
 [<c05d15a6>] ? selinux_ip_postroute+0x56/0x320
 [<c0615988>] ? cfq_add_rq_rb+0x98/0x110
 [<c0852df8>] ? packet_rcv+0x48/0x350
 [<c07c5839>] ? dev_queue_xmit_nit+0xc9/0x140
...

Fix it by splitting vmxnet3_parse_and_copy_hdr into two functions:

vmxnet3_parse_hdr, which sets up the internal/on stack ctx datastructure, and
pulls the skb (both of which can be done without holding the spinlock with irqs
disabled

and

vmxnet3_copy_header, which just copies the skb to the tx ring under the lock
safely.

tested and shown to correct the described problem.  Applies cleanly to the head
of the net tree
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Shrikrishna Khare <skhare@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: "David S. Miller" <davem@davemloft.net>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2016-03-04' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.5

iwlwifi

* free firmware paging memory when the module is unloaded or device removed
* fix pending frames counter to fix an issue when removing stations

ssb

* fix a build problem related to ssb_fill_sprom_with_fallback()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The MFD_SYSCON depends on HAS_IOMEM so when selecting it avoid unmet
direct dependencies.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If skb_linearize fails, the driver should drop the packet
instead of trying to copy it into the bounce buffer.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some devices will silently fail setup unless they are reset first.
This is necessary even if the data interface is already in
altsetting 0, which it will be when the device is probed for the
first time.  Briefly toggling the altsetting forces a function
reset regardless of the initial state.

This fixes a setup problem observed on a number of Huawei devices,
appearing to operate in NTB-32 mode even if we explicitly set them
to NTB-16 mode.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case bind() works, but a later error forces bailing
in probe() in error cases work and a timer may be scheduled.
They must be killed. This fixes an error case related to
the double free reported in
http://www.spinics.net/lists/netdev/msg367669.html
and needs to go on top of Linus' fix to cdc-ncm.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: couple of fixes

Couple of fixes from Ido.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The descriptor queues for sending (SDQs) and receiving (RDQs) packets
are managed by two counters - producer and consumer - which are both
16-bit in size. A queue is considered full when the difference between
the two equals the queue's maximum number of descriptors.

However, if the producer counter overflows, then it's possible for the
full queue check to fail, as it doesn't take the overflow into account.
In such a case, descriptors already passed to the device - but for which
a completion has yet to be posted - will be overwritten, thereby causing
undefined behavior. The above can be achieved under heavy load (~30
netperf instances).

Fix that by casting the subtraction result to u16, preventing it from
being treated as a signed integer.

Fixes: eda6500a ("mlxsw: Add PCI bus implementation")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since we only support one VLAN filtering bridge we need to associate a
reference count with it, so that when the last port netdev leaves it, we
would know that a different bridge can be offloaded to hardware.

When a LAG device is memeber in a bridge and port netdevs are leaving
the LAG, we should always decrement the bridge's reference count, as it's
incremented for any port in the LAG.

Fixes: 4dc236c3 ("mlxsw: spectrum: Handle port leaving LAG while bridged")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 4d5cfcba ('tipc: fix connection abort during subscription
cancel'), removes the check for a valid subscription before calling
tipc_nametbl_subscribe().

This will lead to a nullptr exception when we process a
subscription cancel request. For a cancel request, a null
subscription is passed to tipc_nametbl_subscribe() resulting
in exception.

In this commit, we call tipc_nametbl_subscribe() only for
a valid subscription.

Fixes: 4d5cfcba ('tipc: fix connection abort during subscription cancel')
Reported-by: Anders Widell <anders.widell@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

priv->mdio->irq used to be allocated and required freeing, but it
is now a fixed sized array and should no longer be free'd.

Issue detected using static analysis with CoverityScan

Fixes: e7f4dc35 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

priv->mdio->irq used to be allocated and required freeing, but it
is now a fixed sized array and should no longer be free'd.

Issue detected using static analysis with CoverityScan

Fixes: e7f4dc35 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before calling the destroy() or target() callbacks, the family parameter
field has to be initialized. Otherwise at least the LOG target will
refuse to work and upon removal oops the kernel.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Used to be allocated and required freeing, but now
priv->mdio->irq is now a fixed sized array and should no longer be
free'd.

Issue detected using static analysis with CoverityScan

Fixes: e7f4dc35 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable workaround for MPC8548E erratum eTSEC 106,
"Excess delays when transmitting TOE=1 large frames".
(see commit 53fad773 "gianfar: Enable eTSEC-20 erratum w/a
for P2020 Rev1")

This erratum was fixed in Rev 3.1.x.
Signed-off-by: Atsushi Nemoto <nemoto@toshiba-tops.co.jp>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull ARM SoC fix from Olof Johansson:
 "Tiny fixes branch this week, in fact only one patch.

  Turns out the USB support for a Renesas board was developed on a
  pre-release board that ended up being changed before shipping.  To
  avoid breakage on those boards, and avoid confusion, it's a reasonable
  idea to patch now instead of later.  There are no known users of the
  pre-release variant any more"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: dts: porter: remove enable prop from HS-USB device node

Pull ARM fixes from Russell King:
 "Just two ARM fixes this time: one to fix the hyp-stub for older ARM
  CPUs, and another to fix the set_memory_xx() permission functions to
  deal with zero sizes correctly"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8544/1: set_memory_xx fixes
  ARM: 8534/1: virt: fix hyp-stub build for pre-ARMv7 CPUs

Pull ceph fix from Sage Weil:
 "This is a final commit we missed to align the protocol compatibility
  with the feature bits.

  It decodes a few extra fields in two different messages and reports
  EIO when they are used (not yet supported)"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  ceph: initial CEPH_FEATURE_FS_FILE_LAYOUT_V2 support

Pull UBI fix from Richard Weinberger:
 "This contains a single bug fix for UBI"

* tag 'upstream-4.5-rc7' of git://git.infradead.org/linux-ubifs:
  ubi: Fix out of bounds write in volume update code

Pull UML fixes from Richard Weinberger:
 "This contains three bug/build fixes"

* 'for-linus-4.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: use %lx format specifiers for unsigned longs
  um: Export pm_power_off
  Revert "um: Fix get_signal() usage"

Pull MIPS fixes from Ralf Baechle:
 "Another round of fixes for 4.5:

   - Fix the use of an undocumented syntactial variant of the .type
     pseudo op which is not supported by the LLVM assembler.
   - Fix invalid initialization on S-cache-less systems.
   - Fix possible information leak from the kernel stack for SIGFPE.
   - Fix handling of copy_{from,to}_user() return value in KVM
   - Fix the last instance of irq_to_gpio() which now was causing build
     errors"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: traps: Fix SIGFPE information leak from `do_ov' and `do_trap_or_bp'
  MIPS: kvm: Fix ioctl error handling.
  MIPS: scache: Fix scache init with invalid line size.
  MIPS: Avoid variant of .type unsupported by LLVM Assembler
  MIPS: jz4740: Fix surviving instance of irq_to_gpio()

Pull powerpc fixes from Michael Ellerman:
 - cxl: Fix PSL timebase synchronization detection from Frederic Barrat
 - Fix oops when destroying hw_breakpoint event from Ravi Bangoria
 - Avoid lbarx on e5500 from Scott Wood

* tag 'powerpc-4.5-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/fsl-book3e: Avoid lbarx on e5500
  powerpc/hw_breakpoint: Fix oops when destroying hw_breakpoint event
  cxl: Fix PSL timebase synchronization detection

Pull i2c fix from Wolfram Sang:
 "One I2C bugfix ensuring correct memory allocation in a driver"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: brcmstb: allocate correct amount of memory for regmap

Pull USB fixes from Greg KH:
 "Here are some USB driver ids for 4.5-rc7, and the removal of a driver
  we merged in 4.5-rc1 but it turns out it's not needed as the hardware
  is the same as a driver we already have in the tree.

  This was only figured out after doing a lot of cleanup on it, gotta
  love vendor-provided drivers...  The new device ids for the devices
  for this driver will be added later on when testing is completed, but
  for now, we will remove the driver to keep people from accidentally
  cleaning it up.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-4.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: qcserial: add Sierra Wireless EM74xx device ID
  Revert "USB: serial: add Moxa UPORT 11x0 driver"
  USB: serial: option: add support for Quectel UC20
  USB: serial: option: add support for Telit LE922 PID 0x1045
  USB: cp210x: Add ID for Parrot NMEA GPS Flight Recorder
  USB: qcserial: add Dell Wireless 5809e Gobi 4G HSPA+ (rev3)
  usb: chipidea: otg: change workqueue ci_otg as freezable

static analysis from cppcheck detected %x being used for
unsigned longs:

[arch/x86/um/os-Linux/task_size.c:112]: (warning) %x in format
  string (no. 1) requires 'unsigned int' but the argument type
  is 'unsigned long'.

Use %lx instead of %x
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Richard Weinberger <richard@nod.at>