commit 49e4b843 upstream.

Currently when the system is trying to uninstall the ACPI interrupt
handler, it uses acpi_gbl_FADT.sci_interrupt as the IRQ number.
However, the IRQ number that the ACPI interrupt handled is installed
for comes from acpi_gsi_to_irq() and that is the number that should
be used for the handler removal.

Fix this problem by using the mapped IRQ returned from acpi_gsi_to_irq()
as appropriate.
Acked-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 1e6e6328 upstream.

This adds the USB ID for the Sitecom WLA2100. The Windows 10 inf file
was checked to verify that the addition is correct.
Reported-by: Frans van de Wiel <fvdw@fvdw.eu>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Frans van de Wiel <fvdw@fvdw.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 18e0afab upstream.

T: Bus=04 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=817b Rev=00.02
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

BugLink: https://bugs.launchpad.net/bugs/1506615Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit cd355ff0 upstream.

This adapter works with the existing linux-firmware.

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0930 ProdID=021c Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

BugLink: https://bugs.launchpad.net/bugs/1502781Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 4327ba52 upstream.

If a EXT4 filesystem utilizes JBD2 journaling and an error occurs, the
journaling will be aborted first and the error number will be recorded
into JBD2 superblock and, finally, the system will enter into the
panic state in "errors=panic" option.  But, in the rare case, this
sequence is little twisted like the below figure and it will happen
that the system enters into panic state, which means the system reset
in mobile environment, before completion of recording an error in the
journal superblock. In this case, e2fsck cannot recognize that the
filesystem failure occurred in the previous run and the corruption
wouldn't be fixed.

Task A                        Task B
ext4_handle_error()
-> jbd2_journal_abort()
  -> __journal_abort_soft()
    -> __jbd2_journal_abort_hard()
    | -> journal->j_flags |= JBD2_ABORT;
    |
    |                         __ext4_abort()
    |                         -> jbd2_journal_abort()
    |                         | -> __journal_abort_soft()
    |                         |   -> if (journal->j_flags & JBD2_ABORT)
    |                         |           return;
    |                         -> panic()
    |
    -> jbd2_journal_update_sb_errno()
Tested-by: Hobin Woo <hobin.woo@samsung.com>
Signed-off-by: Daeho Jeong <daeho.jeong@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 0305cd5f upstream.

When truncating a file to a smaller size which consists of an inline
extent that is compressed, we did not discard (or made unusable) the
data between the new file size and the old file size, wasting metadata
space and allowing for the truncated data to be leaked and the data
corruption/loss mentioned below.
We were also not correctly decrementing the number of bytes used by the
inode, we were setting it to zero, giving a wrong report for callers of
the stat(2) syscall. The fsck tool also reported an error about a mismatch
between the nbytes of the file versus the real space used by the file.

Now because we weren't discarding the truncated region of the file, it
was possible for a caller of the clone ioctl to actually read the data
that was truncated, allowing for a security breach without requiring root
access to the system, using only standard filesystem operations. The
scenario is the following:

   1) User A creates a file which consists of an inline and compressed
      extent with a size of 2000 bytes - the file is not accessible to
      any other users (no read, write or execution permission for anyone
      else);

   2) The user truncates the file to a size of 1000 bytes;

   3) User A makes the file world readable;

   4) User B creates a file consisting of an inline extent of 2000 bytes;

   5) User B issues a clone operation from user A's file into its own
      file (using a length argument of 0, clone the whole range);

   6) User B now gets to see the 1000 bytes that user A truncated from
      its file before it made its file world readbale. User B also lost
      the bytes in the range [1000, 2000[ bytes from its own file, but
      that might be ok if his/her intention was reading stale data from
      user A that was never supposed to be public.

Note that this contrasts with the case where we truncate a file from 2000
bytes to 1000 bytes and then truncate it back from 1000 to 2000 bytes. In
this case reading any byte from the range [1000, 2000[ will return a value
of 0x00, instead of the original data.

This problem exists since the clone ioctl was added and happens both with
and without my recent data loss and file corruption fixes for the clone
ioctl (patch "Btrfs: fix file corruption and data loss after cloning
inline extents").

So fix this by truncating the compressed inline extents as we do for the
non-compressed case, which involves decompressing, if the data isn't already
in the page cache, compressing the truncated version of the extent, writing
the compressed content into the inline extent and then truncate it.

The following test case for fstests reproduces the problem. In order for
the test to pass both this fix and my previous fix for the clone ioctl
that forbids cloning a smaller inline extent into a larger one,
which is titled "Btrfs: fix file corruption and data loss after cloning
inline extents", are needed. Without that other fix the test fails in a
different way that does not leak the truncated data, instead part of
destination file gets replaced with zeroes (because the destination file
has a larger inline extent than the source).

  seq=`basename $0`
  seqres=$RESULT_DIR/$seq
  echo "QA output created by $seq"
  tmp=/tmp/$$
  status=1	# failure is the default!
  trap "_cleanup; exit \$status" 0 1 2 3 15

  _cleanup()
  {
      rm -f $tmp.*
  }

  # get standard environment, filters and checks
  . ./common/rc
  . ./common/filter

  # real QA test starts here
  _need_to_be_root
  _supported_fs btrfs
  _supported_os Linux
  _require_scratch
  _require_cloner

  rm -f $seqres.full

  _scratch_mkfs >>$seqres.full 2>&1
  _scratch_mount "-o compress"

  # Create our test files. File foo is going to be the source of a clone operation
  # and consists of a single inline extent with an uncompressed size of 512 bytes,
  # while file bar consists of a single inline extent with an uncompressed size of
  # 256 bytes. For our test's purpose, it's important that file bar has an inline
  # extent with a size smaller than foo's inline extent.
  $XFS_IO_PROG -f -c "pwrite -S 0xa1 0 128"   \
          -c "pwrite -S 0x2a 128 384" \
          $SCRATCH_MNT/foo | _filter_xfs_io
  $XFS_IO_PROG -f -c "pwrite -S 0xbb 0 256" $SCRATCH_MNT/bar | _filter_xfs_io

  # Now durably persist all metadata and data. We do this to make sure that we get
  # on disk an inline extent with a size of 512 bytes for file foo.
  sync

  # Now truncate our file foo to a smaller size. Because it consists of a
  # compressed and inline extent, btrfs did not shrink the inline extent to the
  # new size (if the extent was not compressed, btrfs would shrink it to 128
  # bytes), it only updates the inode's i_size to 128 bytes.
  $XFS_IO_PROG -c "truncate 128" $SCRATCH_MNT/foo

  # Now clone foo's inline extent into bar.
  # This clone operation should fail with errno EOPNOTSUPP because the source
  # file consists only of an inline extent and the file's size is smaller than
  # the inline extent of the destination (128 bytes < 256 bytes). However the
  # clone ioctl was not prepared to deal with a file that has a size smaller
  # than the size of its inline extent (something that happens only for compressed
  # inline extents), resulting in copying the full inline extent from the source
  # file into the destination file.
  #
  # Note that btrfs' clone operation for inline extents consists of removing the
  # inline extent from the destination inode and copy the inline extent from the
  # source inode into the destination inode, meaning that if the destination
  # inode's inline extent is larger (N bytes) than the source inode's inline
  # extent (M bytes), some bytes (N - M bytes) will be lost from the destination
  # file. Btrfs could copy the source inline extent's data into the destination's
  # inline extent so that we would not lose any data, but that's currently not
  # done due to the complexity that would be needed to deal with such cases
  # (specially when one or both extents are compressed), returning EOPNOTSUPP, as
  # it's normally not a very common case to clone very small files (only case
  # where we get inline extents) and copying inline extents does not save any
  # space (unlike for normal, non-inlined extents).
  $CLONER_PROG -s 0 -d 0 -l 0 $SCRATCH_MNT/foo $SCRATCH_MNT/bar

  # Now because the above clone operation used to succeed, and due to foo's inline
  # extent not being shinked by the truncate operation, our file bar got the whole
  # inline extent copied from foo, making us lose the last 128 bytes from bar
  # which got replaced by the bytes in range [128, 256[ from foo before foo was
  # truncated - in other words, data loss from bar and being able to read old and
  # stale data from foo that should not be possible to read anymore through normal
  # filesystem operations. Contrast with the case where we truncate a file from a
  # size N to a smaller size M, truncate it back to size N and then read the range
  # [M, N[, we should always get the value 0x00 for all the bytes in that range.

  # We expected the clone operation to fail with errno EOPNOTSUPP and therefore
  # not modify our file's bar data/metadata. So its content should be 256 bytes
  # long with all bytes having the value 0xbb.
  #
  # Without the btrfs bug fix, the clone operation succeeded and resulted in
  # leaking truncated data from foo, the bytes that belonged to its range
  # [128, 256[, and losing data from bar in that same range. So reading the
  # file gave us the following content:
  #
  # 0000000 a1 a1 a1 a1 a1 a1 a1 a1 a1 a1 a1 a1 a1 a1 a1 a1
  # *
  # 0000200 2a 2a 2a 2a 2a 2a 2a 2a 2a 2a 2a 2a 2a 2a 2a 2a
  # *
  # 0000400
  echo "File bar's content after the clone operation:"
  od -t x1 $SCRATCH_MNT/bar

  # Also because the foo's inline extent was not shrunk by the truncate
  # operation, btrfs' fsck, which is run by the fstests framework everytime a
  # test completes, failed reporting the following error:
  #
  #  root 5 inode 257 errors 400, nbytes wrong

  status=0
  exit
Signed-off-by: Filipe Manana <fdmanana@suse.com>
[bwh: Backported to 3.2:
 - Adjust parameters to btrfs_truncate_page() and btrfs_truncate_item()
 - Pass transaction pointer into truncate_inline_extent()
 - Add prototype of btrfs_truncate_page()
 - s/test_bit(BTRFS_ROOT_REF_COWS, &root->state)/root->ref_cows/
 - Keep using BUG_ON() for other error cases, as there is no
   btrfs_abort_transaction()
 - Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 514ac8ad upstream.

If we truncate an uncompressed inline item, ram_bytes isn't updated to reflect
the new size.  The fixe uses the size directly from the item header when
reading uncompressed inlines, and also fixes truncate to update the
size as it goes.
Reported-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
[bwh: Backported to 3.2:
 - Don't use btrfs_map_token API
 - There are fewer callers of btrfs_file_extent_inline_len() to change
 - Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 54c09889 upstream.

The z2 machine calls pxa27x_set_pwrmode() in order to power off
the machine, but this function gets discarded early at boot because
it is marked __init, as pointed out by kbuild:

WARNING: vmlinux.o(.text+0x145c4): Section mismatch in reference from the function z2_power_off() to the function .init.text:pxa27x_set_pwrmode()
The function z2_power_off() references
the function __init pxa27x_set_pwrmode().
This is often because z2_power_off lacks a __init
annotation or the annotation of pxa27x_set_pwrmode is wrong.

This removes the __init section modifier to fix rebooting and the
build error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: ba4a90a6 ("ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer available")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit d14053b3 upstream.

The VT-d specification says that "Software must enable ATS on endpoint
devices behind a Root Port only if the Root Port is reported as
supporting ATS transactions."

We walk up the tree to find a Root Port, but for integrated devices we
don't find one — we get to the host bridge. In that case we *should*
allow ATS. Currently we don't, which means that we are incorrectly
failing to use ATS for the integrated graphics. Fix that.

We should never break out of this loop "naturally" with bus==NULL,
since we'll always find bridge==NULL in that case (and now return 1).

So remove the check for (!bridge) after the loop, since it can never
happen. If it did, it would be worthy of a BUG_ON(!bridge). But since
it'll oops anyway in that case, that'll do just as well.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
[bwh: Backported to 3.2:
 - Adjust context
 - There's no (!bridge) check to remove]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 8039d87d upstream.

Currently the clone ioctl allows to clone an inline extent from one file
to another that already has other (non-inlined) extents. This is a problem
because btrfs is not designed to deal with files having inline and regular
extents, if a file has an inline extent then it must be the only extent
in the file and must start at file offset 0. Having a file with an inline
extent followed by regular extents results in EIO errors when doing reads
or writes against the first 4K of the file.

Also, the clone ioctl allows one to lose data if the source file consists
of a single inline extent, with a size of N bytes, and the destination
file consists of a single inline extent with a size of M bytes, where we
have M > N. In this case the clone operation removes the inline extent
from the destination file and then copies the inline extent from the
source file into the destination file - we lose the M - N bytes from the
destination file, a read operation will get the value 0x00 for any bytes
in the the range [N, M] (the destination inode's i_size remained as M,
that's why we can read past N bytes).

So fix this by not allowing such destructive operations to happen and
return errno EOPNOTSUPP to user space.

Currently the fstest btrfs/035 tests the data loss case but it totally
ignores this - i.e. expects the operation to succeed and does not check
the we got data loss.

The following test case for fstests exercises all these cases that result
in file corruption and data loss:

  seq=`basename $0`
  seqres=$RESULT_DIR/$seq
  echo "QA output created by $seq"
  tmp=/tmp/$$
  status=1	# failure is the default!
  trap "_cleanup; exit \$status" 0 1 2 3 15

  _cleanup()
  {
      rm -f $tmp.*
  }

  # get standard environment, filters and checks
  . ./common/rc
  . ./common/filter

  # real QA test starts here
  _need_to_be_root
  _supported_fs btrfs
  _supported_os Linux
  _require_scratch
  _require_cloner
  _require_btrfs_fs_feature "no_holes"
  _require_btrfs_mkfs_feature "no-holes"

  rm -f $seqres.full

  test_cloning_inline_extents()
  {
      local mkfs_opts=$1
      local mount_opts=$2

      _scratch_mkfs $mkfs_opts >>$seqres.full 2>&1
      _scratch_mount $mount_opts

      # File bar, the source for all the following clone operations, consists
      # of a single inline extent (50 bytes).
      $XFS_IO_PROG -f -c "pwrite -S 0xbb 0 50" $SCRATCH_MNT/bar \
          | _filter_xfs_io

      # Test cloning into a file with an extent (non-inlined) where the
      # destination offset overlaps that extent. It should not be possible to
      # clone the inline extent from file bar into this file.
      $XFS_IO_PROG -f -c "pwrite -S 0xaa 0K 16K" $SCRATCH_MNT/foo \
          | _filter_xfs_io
      $CLONER_PROG -s 0 -d 0 -l 0 $SCRATCH_MNT/bar $SCRATCH_MNT/foo

      # Doing IO against any range in the first 4K of the file should work.
      # Due to a past clone ioctl bug which allowed cloning the inline extent,
      # these operations resulted in EIO errors.
      echo "File foo data after clone operation:"
      # All bytes should have the value 0xaa (clone operation failed and did
      # not modify our file).
      od -t x1 $SCRATCH_MNT/foo
      $XFS_IO_PROG -c "pwrite -S 0xcc 0 100" $SCRATCH_MNT/foo | _filter_xfs_io

      # Test cloning the inline extent against a file which has a hole in its
      # first 4K followed by a non-inlined extent. It should not be possible
      # as well to clone the inline extent from file bar into this file.
      $XFS_IO_PROG -f -c "pwrite -S 0xdd 4K 12K" $SCRATCH_MNT/foo2 \
          | _filter_xfs_io
      $CLONER_PROG -s 0 -d 0 -l 0 $SCRATCH_MNT/bar $SCRATCH_MNT/foo2

      # Doing IO against any range in the first 4K of the file should work.
      # Due to a past clone ioctl bug which allowed cloning the inline extent,
      # these operations resulted in EIO errors.
      echo "File foo2 data after clone operation:"
      # All bytes should have the value 0x00 (clone operation failed and did
      # not modify our file).
      od -t x1 $SCRATCH_MNT/foo2
      $XFS_IO_PROG -c "pwrite -S 0xee 0 90" $SCRATCH_MNT/foo2 | _filter_xfs_io

      # Test cloning the inline extent against a file which has a size of zero
      # but has a prealloc extent. It should not be possible as well to clone
      # the inline extent from file bar into this file.
      $XFS_IO_PROG -f -c "falloc -k 0 1M" $SCRATCH_MNT/foo3 | _filter_xfs_io
      $CLONER_PROG -s 0 -d 0 -l 0 $SCRATCH_MNT/bar $SCRATCH_MNT/foo3

      # Doing IO against any range in the first 4K of the file should work.
      # Due to a past clone ioctl bug which allowed cloning the inline extent,
      # these operations resulted in EIO errors.
      echo "First 50 bytes of foo3 after clone operation:"
      # Should not be able to read any bytes, file has 0 bytes i_size (the
      # clone operation failed and did not modify our file).
      od -t x1 $SCRATCH_MNT/foo3
      $XFS_IO_PROG -c "pwrite -S 0xff 0 90" $SCRATCH_MNT/foo3 | _filter_xfs_io

      # Test cloning the inline extent against a file which consists of a
      # single inline extent that has a size not greater than the size of
      # bar's inline extent (40 < 50).
      # It should be possible to do the extent cloning from bar to this file.
      $XFS_IO_PROG -f -c "pwrite -S 0x01 0 40" $SCRATCH_MNT/foo4 \
          | _filter_xfs_io
      $CLONER_PROG -s 0 -d 0 -l 0 $SCRATCH_MNT/bar $SCRATCH_MNT/foo4

      # Doing IO against any range in the first 4K of the file should work.
      echo "File foo4 data after clone operation:"
      # Must match file bar's content.
      od -t x1 $SCRATCH_MNT/foo4
      $XFS_IO_PROG -c "pwrite -S 0x02 0 90" $SCRATCH_MNT/foo4 | _filter_xfs_io

      # Test cloning the inline extent against a file which consists of a
      # single inline extent that has a size greater than the size of bar's
      # inline extent (60 > 50).
      # It should not be possible to clone the inline extent from file bar
      # into this file.
      $XFS_IO_PROG -f -c "pwrite -S 0x03 0 60" $SCRATCH_MNT/foo5 \
          | _filter_xfs_io
      $CLONER_PROG -s 0 -d 0 -l 0 $SCRATCH_MNT/bar $SCRATCH_MNT/foo5

      # Reading the file should not fail.
      echo "File foo5 data after clone operation:"
      # Must have a size of 60 bytes, with all bytes having a value of 0x03
      # (the clone operation failed and did not modify our file).
      od -t x1 $SCRATCH_MNT/foo5

      # Test cloning the inline extent against a file which has no extents but
      # has a size greater than bar's inline extent (16K > 50).
      # It should not be possible to clone the inline extent from file bar
      # into this file.
      $XFS_IO_PROG -f -c "truncate 16K" $SCRATCH_MNT/foo6 | _filter_xfs_io
      $CLONER_PROG -s 0 -d 0 -l 0 $SCRATCH_MNT/bar $SCRATCH_MNT/foo6

      # Reading the file should not fail.
      echo "File foo6 data after clone operation:"
      # Must have a size of 16K, with all bytes having a value of 0x00 (the
      # clone operation failed and did not modify our file).
      od -t x1 $SCRATCH_MNT/foo6

      # Test cloning the inline extent against a file which has no extents but
      # has a size not greater than bar's inline extent (30 < 50).
      # It should be possible to clone the inline extent from file bar into
      # this file.
      $XFS_IO_PROG -f -c "truncate 30" $SCRATCH_MNT/foo7 | _filter_xfs_io
      $CLONER_PROG -s 0 -d 0 -l 0 $SCRATCH_MNT/bar $SCRATCH_MNT/foo7

      # Reading the file should not fail.
      echo "File foo7 data after clone operation:"
      # Must have a size of 50 bytes, with all bytes having a value of 0xbb.
      od -t x1 $SCRATCH_MNT/foo7

      # Test cloning the inline extent against a file which has a size not
      # greater than the size of bar's inline extent (20 < 50) but has
      # a prealloc extent that goes beyond the file's size. It should not be
      # possible to clone the inline extent from bar into this file.
      $XFS_IO_PROG -f -c "falloc -k 0 1M" \
                      -c "pwrite -S 0x88 0 20" \
                      $SCRATCH_MNT/foo8 | _filter_xfs_io
      $CLONER_PROG -s 0 -d 0 -l 0 $SCRATCH_MNT/bar $SCRATCH_MNT/foo8

      echo "File foo8 data after clone operation:"
      # Must have a size of 20 bytes, with all bytes having a value of 0x88
      # (the clone operation did not modify our file).
      od -t x1 $SCRATCH_MNT/foo8

      _scratch_unmount
  }

  echo -e "\nTesting without compression and without the no-holes feature...\n"
  test_cloning_inline_extents

  echo -e "\nTesting with compression and without the no-holes feature...\n"
  test_cloning_inline_extents "" "-o compress"

  echo -e "\nTesting without compression and with the no-holes feature...\n"
  test_cloning_inline_extents "-O no-holes" ""

  echo -e "\nTesting with compression and with the no-holes feature...\n"
  test_cloning_inline_extents "-O no-holes" "-o compress"

  status=0
  exit
Signed-off-by: Filipe Manana <fdmanana@suse.com>
[bwh: Backported to 3.2:
 - Adjust parameters to btrfs_drop_extents()
 - Drop use of ASSERT()
 - Keep using BUG_ON() for other error cases, as there is no
   btrfs_abort_transaction()
 - Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit c7d22a3c upstream.

btrfs_next_item() makes the btrfs path point to the next item, crossing leaf
boundaries if needed.
Signed-off-by: Arne Jansen <sensille@gmx.net>
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
[bwh: Dependency of the following fix]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 161642e2 upstream.

Recent TCP listener patches exposed a prior af_packet bug :
match_fanout_group() blindly assumes it is always safe
to cast sk to a packet socket to compare fanout with af_packet_priv

But SYNACK packets can be sent while attached to request_sock, which
are smaller than a "struct sock".

We can read non existent memory and crash.

Fixes: c0de08d0 ("af_packet: don't emit packet on orig fanout group")
Fixes: ca6fb065 ("tcp: attach SYNACK messages to request sockets instead of listener")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Eric Leblond <eric@regit.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 1f35d04a upstream.

The iomap[] array has PCIM_IOMAP_MAX (6) elements and not
DEVICE_COUNT_RESOURCE (16).  This bug was found using a static checker.
It may be that the "if (!(mask & (1 << i)))" check means we never
actually go past the end of the array in real life.

Fixes: ec04b075 ('iomap: implement pcim_iounmap_regions()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit e5bae867 upstream.

If we fail to allocate a partition structure in the middle of the partition
creation process, the already allocated partitions are never removed, which
means they are still present in the partition list and their resources are
never freed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 1f9c6e1b upstream.

There were several bugs here.

1)  The done label was in the wrong place so we didn't copy any
    information out when there was no command given.

2)  We were using PAGE_SIZE as the size of the buffer instead of
    "PAGE_SIZE - pos".

3)  snprintf() returns the number of characters that would have been
    printed if there were enough space.  If there was not enough space
    (and we had fixed the memory corruption bug #2) then it would result
    in an information leak when we do simple_read_from_buffer().  I've
    changed it to use scnprintf() instead.

I also removed the initialization at the start of the function, because
I thought it made the code a little more clear.

Fixes: 5e6e3a92 ('wireless: mwifiex: initial commit for Marvell mwifiex driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 90adf98d upstream.

Since commit 1c6c6952 ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail.

scripts/coccinelle/misc/irqf_oneshot.cocci detected this issue.

Fixes: b5874f33 ("wm831x_power: Use genirq")
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 79b568b9 upstream.

hid_connect adds various strings to the buffer but they're all
conditional. You can find circumstances where nothing would be written
to it but the kernel will still print the supposedly empty buffer with
printk. This leads to corruption on the console/in the logs.

Ensure buf is initialized to an empty string.
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
[dvhart: Initialize string to "" rather than assign buf[0] = NULL;]
Cc: Jiri Kosina <jikos@kernel.org>
Cc: linux-input@vger.kernel.org
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 8ec6d978 upstream.

The ifmgd->ave_beacon_signal value cannot be taken as is for
comparisons, it must be divided by since it's represented
like that for better accuracy of the EWMA calculations. This
would lead to invalid driver RSSI events. Fix the used value.

Fixes: 615f7b9b ("mac80211: add driver RSSI threshold events")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit da2d03ea upstream.

932c435c ("PCI: Add dev_flags bit to access VPD through function 0")
added PCI_DEV_FLAGS_VPD_REF_F0.  Previously, we set the flag on every
non-zero function of quirked devices.  If a function turned out to be
different from function 0, i.e., it had a different class, vendor ID, or
device ID, the flag remained set but we didn't make VPD accessible at all.

Flip this around so we only set PCI_DEV_FLAGS_VPD_REF_F0 for functions that
are identical to function 0, and allow regular VPD access for any other
functions.

[bhelgaas: changelog, stable tag]
Fixes: 932c435c ("PCI: Add dev_flags bit to access VPD through function 0")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
Acked-by: Mark Rustad <mark.d.rustad@intel.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 9d924075 upstream.

Commit 932c435c ("PCI: Add dev_flags bit to access VPD through function
0") passes PCI_SLOT(devfn) for the devfn parameter of pci_get_slot().
Generally this works because we're fairly well guaranteed that a PCIe
device is at slot address 0, but for the general case, including
conventional PCI, it's incorrect.  We need to get the slot and then convert
it back into a devfn.

Fixes: 932c435c ("PCI: Add dev_flags bit to access VPD through function 0")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
Acked-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit f05819df upstream.

The following sequence of commands:

    i=`keyctl add user a a @s`
    keyctl request2 keyring foo bar @t
    keyctl unlink $i @s

tries to invoke an upcall to instantiate a keyring if one doesn't already
exist by that name within the user's keyring set.  However, if the upcall
fails, the code sets keyring->type_data.reject_error to -ENOKEY or some
other error code.  When the key is garbage collected, the key destroy
function is called unconditionally and keyring_destroy() uses list_empty()
on keyring->type_data.link - which is in a union with reject_error.
Subsequently, the kernel tries to unlink the keyring from the keyring names
list - which oopses like this:

	BUG: unable to handle kernel paging request at 00000000ffffff8a
	IP: [<ffffffff8126e051>] keyring_destroy+0x3d/0x88
	...
	Workqueue: events key_garbage_collector
	...
	RIP: 0010:[<ffffffff8126e051>] keyring_destroy+0x3d/0x88
	RSP: 0018:ffff88003e2f3d30  EFLAGS: 00010203
	RAX: 00000000ffffff82 RBX: ffff88003bf1a900 RCX: 0000000000000000
	RDX: 0000000000000000 RSI: 000000003bfc6901 RDI: ffffffff81a73a40
	RBP: ffff88003e2f3d38 R08: 0000000000000152 R09: 0000000000000000
	R10: ffff88003e2f3c18 R11: 000000000000865b R12: ffff88003bf1a900
	R13: 0000000000000000 R14: ffff88003bf1a908 R15: ffff88003e2f4000
	...
	CR2: 00000000ffffff8a CR3: 000000003e3ec000 CR4: 00000000000006f0
	...
	Call Trace:
	 [<ffffffff8126c756>] key_gc_unused_keys.constprop.1+0x5d/0x10f
	 [<ffffffff8126ca71>] key_garbage_collector+0x1fa/0x351
	 [<ffffffff8105ec9b>] process_one_work+0x28e/0x547
	 [<ffffffff8105fd17>] worker_thread+0x26e/0x361
	 [<ffffffff8105faa9>] ? rescuer_thread+0x2a8/0x2a8
	 [<ffffffff810648ad>] kthread+0xf3/0xfb
	 [<ffffffff810647ba>] ? kthread_create_on_node+0x1c2/0x1c2
	 [<ffffffff815f2ccf>] ret_from_fork+0x3f/0x70
	 [<ffffffff810647ba>] ? kthread_create_on_node+0x1c2/0x1c2

Note the value in RAX.  This is a 32-bit representation of -ENOKEY.

The solution is to only call ->destroy() if the key was successfully
instantiated.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
[carnil: Backported for 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 94c4554b upstream.

There appears to be a race between:

 (1) key_gc_unused_keys() which frees key->security and then calls
     keyring_destroy() to unlink the name from the name list

 (2) find_keyring_by_name() which calls key_permission(), thus accessing
     key->security, on a key before checking to see whether the key usage is 0
     (ie. the key is dead and might be cleaned up).

Fix this by calling ->destroy() before cleaning up the core key data -
including key->security.
Reported-by: Petr Matousek <pmatouse@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
[carnil: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 54a20552 upstream.

It was found that a guest can DoS a host by triggering an infinite
stream of "alignment check" (#AC) exceptions.  This causes the
microcode to enter an infinite loop where the core never receives
another interrupt.  The host kernel panics pretty quickly due to the
effects (CVE-2015-5307).
Signed-off-by: Eric Northup <digitaleric@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 3.2:
 - Add definition of AC_VECTOR
 - Adjust filename, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit a41cbe86 upstream.

A test case is as the description says:
open(foobar, O_WRONLY);
sleep()  --> reboot the server
close(foobar)

The bug is because in nfs4state.c in nfs4_reclaim_open_state() a few
line before going to restart, there is
clear_bit(NFS4CLNT_RECLAIM_NOGRACE, &state->flags).

NFS4CLNT_RECLAIM_NOGRACE is a flag for the client states not open
owner states. Value of NFS4CLNT_RECLAIM_NOGRACE is 4 which is the
value of NFS_O_WRONLY_STATE in nfs4_state->flags. So clearing it wipes
out state and when we go to close it, “call_close” doesn’t get set as
state flag is not set and CLOSE doesn’t go on the wire.
Signed-off-by: Olga Kornievskaia <aglo@umich.edu>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 436c2a50 ]

commit 3cc81d85 ("asix: Don't reset PHY on if_up for ASIX 88772")
causes the ethernet on Arndale to no longer function. This appears to
be because the Arndale ethernet requires a full reset before it will
function correctly, however simply reverting the above patch causes
problems with ethtool settings getting reset.

It seems the problem is that the ethernet is not properly reset during
bind, and indeed the code in ax88772_bind that resets the device is a
very small subset of the actual ax88772_reset function. This patch uses
ax88772_reset in place of the existing reset code in ax88772_bind which
removes some code duplication and fixes the ethernet on Arndale.

It is still possible that the original patch causes some issues with
suspend and resume but that seems like a separate issue and I haven't
had a chance to test that yet.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 3cc81d85 ]

I've noticed every time the interface is set to 'up,', the kernel
reports that the link speed is set to 100 Mbps/Full Duplex, even
when ethtool is used to set autonegotiation to 'off', half
duplex, 10 Mbps.
It can be tested by:
 ifconfig eth0 down
 ethtool -s eth0 autoneg off speed 10 duplex half
 ifconfig eth0 up

Then checking 'dmesg' for the link speed.
Signed-off-by: Michel Stam <m.stam@fugro.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 077cb37f ]

It seems that kernel memory can leak into userspace by a
kmalloc, ethtool_get_strings, then copy_to_user sequence.

Avoid this by using kcalloc to zero fill the copied buffer.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 31b33dfb ]

Earlier patch 6ae459bd tried to detect void ckecksum partial
skb by comparing pull length to checksum offset. But it does
not work for all cases since checksum-offset depends on
updates to skb->data.

Following patch fixes it by validating checksum start offset
after skb-data pointer is updated. Negative value of checksum
offset start means there is no need to checksum.

Fixes: 6ae459bd ("skbuff: Fix skb checksum flag on skb pull")
Reported-by: Andrew Vagin <avagin@odin.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 6ae459bd ]

VXLAN device can receive skb with checksum partial. But the checksum
offset could be in outer header which is pulled on receive. This results
in negative checksum offset for the skb. Such skb can cause the assert
failure in skb_checksum_help(). Following patch fixes the bug by setting
checksum-none while pulling outer header.

Following is the kernel panic msg from old kernel hitting the bug.

------------[ cut here ]------------
kernel BUG at net/core/dev.c:1906!
RIP: 0010:[<ffffffff81518034>] skb_checksum_help+0x144/0x150
Call Trace:
<IRQ>
[<ffffffffa0164c28>] queue_userspace_packet+0x408/0x470 [openvswitch]
[<ffffffffa016614d>] ovs_dp_upcall+0x5d/0x60 [openvswitch]
[<ffffffffa0166236>] ovs_dp_process_packet_with_key+0xe6/0x100 [openvswitch]
[<ffffffffa016629b>] ovs_dp_process_received_packet+0x4b/0x80 [openvswitch]
[<ffffffffa016c51a>] ovs_vport_receive+0x2a/0x30 [openvswitch]
[<ffffffffa0171383>] vxlan_rcv+0x53/0x60 [openvswitch]
[<ffffffffa01734cb>] vxlan_udp_encap_recv+0x8b/0xf0 [openvswitch]
[<ffffffff8157addc>] udp_queue_rcv_skb+0x2dc/0x3b0
[<ffffffff8157b56f>] __udp4_lib_rcv+0x1cf/0x6c0
[<ffffffff8157ba7a>] udp_rcv+0x1a/0x20
[<ffffffff8154fdbd>] ip_local_deliver_finish+0xdd/0x280
[<ffffffff81550128>] ip_local_deliver+0x88/0x90
[<ffffffff8154fa7d>] ip_rcv_finish+0x10d/0x370
[<ffffffff81550365>] ip_rcv+0x235/0x300
[<ffffffff8151ba1d>] __netif_receive_skb+0x55d/0x620
[<ffffffff8151c360>] netif_receive_skb+0x80/0x90
[<ffffffff81459935>] virtnet_poll+0x555/0x6f0
[<ffffffff8151cd04>] net_rx_action+0x134/0x290
[<ffffffff810683d8>] __do_softirq+0xa8/0x210
[<ffffffff8162fe6c>] call_softirq+0x1c/0x30
[<ffffffff810161a5>] do_softirq+0x65/0xa0
[<ffffffff810687be>] irq_exit+0x8e/0xb0
[<ffffffff81630733>] do_IRQ+0x63/0xe0
[<ffffffff81625f2e>] common_interrupt+0x6e/0x6e
Reported-by: Anupam Chanda <achanda@vmware.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

Without this length argument, we can read past the end of the iovec in
memcpy_toiovec because we have no way of knowing the total length of the
iovec's buffers.

This is needed for stable kernels where 89c22d8c ("net: Fix skb
csum races when peeking") has been backported but that don't have the
ioviter conversion, which is almost all the stable trees <= 3.18.

This also fixes a kernel crash for NFS servers when the client uses
 -onfsvers=3,proto=udp to mount the export.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
[bwh: Backported to 3.2: adjust context in include/linux/skbuff.h]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 80e0b6e8 upstream.

We accidentally declared pid_alive without any extern/inline connotation.
Some platforms were fine with this, some like ia64 and mips were very angry.
If the function is inline, the prototype should be inline!

on ia64:
include/linux/sched.h:1718: warning: 'pid_alive' declared inline after
being called
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Neal Gompa <ngompa13@gmail.com>

commit 22805217 upstream.

When pci_pool_alloc fails in mvs_task_prep then task->lldd_task stays
NULL but it's later used in mvs_abort_task as slot which is passed
to mvs_slot_task_free causing NULL pointer dereference.

Just return from mvs_slot_task_free when passed with NULL slot.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=101891Signed-off-by: Dāvis Mosāns <davispuh@gmail.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit c340702c upstream.

When a write fails and a bad-block-list is present, we can
update the bad-block-list instead of writing the data.  If
this succeeds then it is OK clear the relevant bitmap-bit as
no further 'sync' of the block is needed.

However if writing the bad-block-list fails then we need to
treat the write as failed and particularly must not clear
the bitmap bit.  Otherwise the device can be re-added (after
any hardware connection issues are resolved) and because the
relevant bit in the bitmap is clear, that block will not be
resynced.  This leads to data corruption.

We already delay the final bio_endio() on the write until
the bad-block-list is written so that when the write
returns: either that data is safe, the bad-block record is
safe, or the fact that the device is faulty is safe.
However we *don't* delay the clearing of the bitmap, so the
bitmap bit can be recorded as cleared before we know if the
bad-block-list was written safely.

So: delay that until the write really is safe.
i.e. move the call to close_write() until just before
calling bio_endio(), and recheck the 'is array degraded'
status before making that call.

This bug goes back to v3.1 when bad-block-lists were
introduced, though it only affects arrays created with
mdadm-3.3 or later as only those have bad-block lists.

Backports will require at least
Commit: 95af587e ("md/raid10: ensure device failure recorded before write request returns.")
as well.  I'll send that to 'stable' separately.

Note that of the two tests of R10BIO_WriteError that this
patch adds, the first is certain to fail and the second is
certain to succeed.  However doing it this way makes the
patch more obviously correct.  I will tidy the code up in a
future merge window.
Reported-by: Nate Dailey <nate.dailey@stratus.com>
Fixes: bd870a16 ("md/raid10:  Handle write errors by updating badblock log.")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 95af587e upstream.

When a write to one of the legs of a RAID10 fails, the failure is
recorded in the metadata of the other legs so that after a restart
the data on the failed drive wont be trusted even if that drive seems
to be working again (maybe a cable was unplugged).

Currently there is no interlock between the write request completing
and the metadata update.  So it is possible that the write will
complete, the app will confirm success in some way, and then the
machine will crash before the metadata update completes.

This is an extremely small hole for a racy to fit in, but it is
theoretically possible and so should be closed.

So:
 - set MD_CHANGE_PENDING when requesting a metadata update for a
   failed device, so we can know with certainty when it completes
 - queue requests that experienced an error on a new queue which
   is only processed after the metadata update completes
 - call raid_end_bio_io() on bios in that queue when the time comes.
Signed-off-by: NeilBrown <neilb@suse.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit bd8688a1 upstream.

When a write fails and a bad-block-list is present, we can
update the bad-block-list instead of writing the data.  If
this succeeds then it is OK clear the relevant bitmap-bit as
no further 'sync' of the block is needed.

However if writing the bad-block-list fails then we need to
treat the write as failed and particularly must not clear
the bitmap bit.  Otherwise the device can be re-added (after
any hardware connection issues are resolved) and because the
relevant bit in the bitmap is clear, that block will not be
resynced.  This leads to data corruption.

We already delay the final bio_endio() on the write until
the bad-block-list is written so that when the write
returns: either that data is safe, the bad-block record is
safe, or the fact that the device is faulty is safe.
However we *don't* delay the clearing of the bitmap, so the
bitmap bit can be recorded as cleared before we know if the
bad-block-list was written safely.

So: delay that until the write really is safe.
i.e. move the call to close_write() until just before
calling bio_endio(), and recheck the 'is array degraded'
status before making that call.

This bug goes back to v3.1 when bad-block-lists were
introduced, though it only affects arrays created with
mdadm-3.3 or later as only those have bad-block lists.

Backports will require at least
Commit: 55ce74d4 ("md/raid1: ensure device failure recorded before write request returns.")
as well.  I'll send that to 'stable' separately.

Note that of the two tests of R1BIO_WriteError that this
patch adds, the first is certain to fail and the second is
certain to succeed.  However doing it this way makes the
patch more obviously correct.  I will tidy the code up in a
future merge window.
Reported-and-tested-by: Nate Dailey <nate.dailey@stratus.com>
Cc: Jes Sorensen <Jes.Sorensen@redhat.com>
Fixes: cd5ff9a1 ("md/raid1:  Handle write errors by updating badblock log.")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 55ce74d4 upstream.

When a write to one of the legs of a RAID1 fails, the failure is
recorded in the metadata of the other leg(s) so that after a restart
the data on the failed drive wont be trusted even if that drive seems
to be working again  (maybe a cable was unplugged).

Similarly when we record a bad-block in response to a write failure,
we must not let the write complete until the bad-block update is safe.

Currently there is no interlock between the write request completing
and the metadata update.  So it is possible that the write will
complete, the app will confirm success in some way, and then the
machine will crash before the metadata update completes.

This is an extremely small hole for a racy to fit in, but it is
theoretically possible and so should be closed.

So:
 - set MD_CHANGE_PENDING when requesting a metadata update for a
   failed device, so we can know with certainty when it completes
 - queue requests that experienced an error on a new queue which
   is only processed after the metadata update completes
 - call raid_end_bio_io() on bios in that queue when the time comes.
Signed-off-by: NeilBrown <neilb@suse.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 4dcb8b57 upstream.

btree_split_beneath()'s error path had an outstanding FIXME that speaks
directly to the potential for _not_ cleaning up a previously allocated
bufio-backed block.

Fix this by releasing the previously allocated bufio block using
unlock_block().
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <thornber@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 2871c69e upstream.

Commit 4c7e3093 ("dm btree remove: fix bug in redistribute3") wasn't
a complete fix for redistribute3().

The redistribute3 function takes 3 btree nodes and shares out the entries
evenly between them.  If the three nodes in total contained
(MAX_ENTRIES * 3) - 1 entries between them then this was erroneously getting
rebalanced as (MAX_ENTRIES - 1) on the left and right, and (MAX_ENTRIES + 1) in
the center.

Fix this issue by being more careful about calculating the target number
of entries for the left and right nodes.

Unit tested in userspace using this program:
https://github.com/jthornber/redistribute3-test/blob/master/redistribute3_t.cSigned-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 1acea4f6 upstream.

We can't rely on PPPOX_ZOMBIE to decide whether to clear po->pppoe_dev.
PPPOX_ZOMBIE can be set by pppoe_disc_rcv() even when po->pppoe_dev is
NULL. So we have no guarantee that (sk->sk_state & PPPOX_ZOMBIE) implies
(po->pppoe_dev != NULL).
Since we're releasing a PPPoE socket, we want to release the pppoe_dev
if it exists and reset sk_state to PPPOX_DEAD, no matter the previous
value of sk_state. So we can just check for po->pppoe_dev and avoid any
assumption on sk->sk_state.

Fixes: 2b018d57 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>