- 06 Aug, 2015 1 commit
-
-
Linus Walleij authored
The "cpus" node cannot be inside the "soc" node, while this works for the CoreSight blocks, the early boot code will look for "cpus" directly under the root node, so this is a hard convention. So move the CPU nodes. Augment the "reg" property to match what is actually in the hardware: 0x300 and 0x301 respectively. Then add an SMP enablement type to be used by the SMP init code, "ste,dbx500-smp". Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
-
- 31 Jul, 2015 1 commit
-
-
Murali Karicheri authored
All of the keystone devices have a separate register to hold post divider value for main pll clock. Currently the fixed-postdiv value used for k2hk/l/e SoCs works by sheer luck as u-boot happens to use a value of 2 for this. Now that we have fixed this in the pll clock driver change the dt bindings for the same. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Olof Johansson <olof@lixom.net>
-
- 28 Jul, 2015 1 commit
-
-
Olof Johansson authored
Merge tag 'imx-fixes-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes The i.MX fixes for 4.2, 2nd round: - Add the required second clock for i.MX35 FlexCAN in device tree, so that the device can be probed by kernel successfully. * tag 'imx-fixes-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: ARM: dts: i.MX35: Fix can support. Signed-off-by: Olof Johansson <olof@lixom.net>
-
- 26 Jul, 2015 2 commits
-
-
Linus Walleij authored
The UART0 is not used on these boards, yet active and blocking other use. Fix this by disabling UART0 and setting port aliases to maintain port enumeration to userspace. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
-
Olof Johansson authored
Merge tag 'for-v4.2-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes Merge "ARM: OMAP2+: hwmod fixes for v4.2-rc" from Paul Walmsley: ARM: OMAP2+: hwmod fixes for v4.2-rc Two fixes against v4.2-rc1. The first, for DRA7xx platforms, corrects some incorrect GPMC hardware description data. The second one will ensure that the hwmod code will wait for any module with CPU-accessible registers to become ready before attempting to access it. Basic build, boot, and PM test logs are available here: http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.2-rc/20150723065408/ Note that I do not have a DRA7xx or AM43xx board, and therefore cannot test on those platforms. * tag 'for-v4.2-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending: ARM: OMAP2+: hwmod: Fix _wait_target_ready() for hwmods without sysc ARM: DRA7: hwmod: fix gpmc hwmod Signed-off-by: Olof Johansson <olof@lixom.net>
-
- 25 Jul, 2015 1 commit
-
-
Denis Carikli authored
Since commit 3d42a379 ("can: flexcan: add 2nd clock to support imx53 and newer") the can driver requires a dt nodes to have a second clock. Add them to imx35 to fix probing the flex can driver on the respective platforms. Signed-off-by: Denis Carikli <denis@eukrea.com> Cc: <stable@vger.kernel.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
- 23 Jul, 2015 1 commit
-
-
Roger Quadros authored
For hwmods without sysc, _init_mpu_rt_base(oh) won't be called and so _find_mpu_rt_port(oh) will return NULL thus preventing ready state check on those modules after the module is enabled. This can potentially cause a bus access error if the module is accessed before the module is ready. Fix this by unconditionally calling _init_mpu_rt_base() during hwmod _init(). Do ioremap only if we need SYSC access. Eventhough _wait_target_ready() check doesn't really need MPU RT port but just the PRCM registers, we still mandate that the hwmod must have an MPU RT port if ready state check needs to be done. Else it would mean that the module is not accessible by MPU so there is no point in waiting for target to be ready. e.g. this fixes the below DCAN bus access error on AM437x-gp-evm. [ 16.672978] ------------[ cut here ]------------ [ 16.677885] WARNING: CPU: 0 PID: 1580 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x234/0x35c() [ 16.687946] 44000000.ocp:L3 Custom Error: MASTER M2 (64-bit) TARGET L4_PER_0 (Read): Data Access in User mode during Functional access [ 16.700654] Modules linked in: xhci_hcd btwilink ti_vpfe dwc3 videobuf2_core ov2659 bluetooth v4l2_common videodev ti_am335x_adc kfifo_buf industrialio c_can_platform videobuf2_dma_contig media snd_soc_tlv320aic3x pixcir_i2c_ts c_can dc [ 16.731144] CPU: 0 PID: 1580 Comm: rpc.statd Not tainted 3.14.26-02561-gf733aa036398 #180 [ 16.739747] Backtrace: [ 16.742336] [<c0011108>] (dump_backtrace) from [<c00112a4>] (show_stack+0x18/0x1c) [ 16.750285] r6:00000093 r5:00000009 r4:eab5b8a8 r3:00000000 [ 16.756252] [<c001128c>] (show_stack) from [<c05a4418>] (dump_stack+0x20/0x28) [ 16.763870] [<c05a43f8>] (dump_stack) from [<c0037120>] (warn_slowpath_common+0x6c/0x8c) [ 16.772408] [<c00370b4>] (warn_slowpath_common) from [<c00371e4>] (warn_slowpath_fmt+0x38/0x40) [ 16.781550] r8:c05d1f90 r7:c0730844 r6:c0730448 r5:80080003 r4:ed0cd210 [ 16.788626] [<c00371b0>] (warn_slowpath_fmt) from [<c027fa94>] (l3_interrupt_handler+0x234/0x35c) [ 16.797968] r3:ed0cd480 r2:c0730508 [ 16.801747] [<c027f860>] (l3_interrupt_handler) from [<c0063758>] (handle_irq_event_percpu+0x54/0x1bc) [ 16.811533] r10:ed005600 r9:c084855b r8:0000002a r7:00000000 r6:00000000 r5:0000002a [ 16.819780] r4:ed0e6d80 [ 16.822453] [<c0063704>] (handle_irq_event_percpu) from [<c00638f0>] (handle_irq_event+0x30/0x40) [ 16.831789] r10:eb2b6938 r9:eb2b6960 r8:bf011420 r7:fa240100 r6:00000000 r5:0000002a [ 16.840052] r4:ed005600 [ 16.842744] [<c00638c0>] (handle_irq_event) from [<c00661d8>] (handle_fasteoi_irq+0x74/0x128) [ 16.851702] r4:ed005600 r3:00000000 [ 16.855479] [<c0066164>] (handle_fasteoi_irq) from [<c0063068>] (generic_handle_irq+0x28/0x38) [ 16.864523] r4:0000002a r3:c0066164 [ 16.868294] [<c0063040>] (generic_handle_irq) from [<c000ef60>] (handle_IRQ+0x38/0x8c) [ 16.876612] r4:c081c640 r3:00000202 [ 16.880380] [<c000ef28>] (handle_IRQ) from [<c00084f0>] (gic_handle_irq+0x30/0x5c) [ 16.888328] r6:eab5ba38 r5:c0804460 r4:fa24010c r3:00000100 [ 16.894303] [<c00084c0>] (gic_handle_irq) from [<c05a8d80>] (__irq_svc+0x40/0x50) [ 16.902193] Exception stack(0xeab5ba38 to 0xeab5ba80) [ 16.907499] ba20: 00000000 00000006 [ 16.916108] ba40: fa1d0000 fa1d0008 ed3d3000 eab5bab4 ed3d3460 c0842af4 bf011420 eb2b6960 [ 16.924716] ba60: eb2b6938 eab5ba8c eab5ba90 eab5ba80 bf035220 bf07702c 600f0013 ffffffff [ 16.933317] r7:eab5ba6c r6:ffffffff r5:600f0013 r4:bf07702c [ 16.939317] [<bf077000>] (c_can_plat_read_reg_aligned_to_16bit [c_can_platform]) from [<bf035220>] (c_can_get_berr_counter+0x38/0x64 [c_can]) [ 16.952696] [<bf0351e8>] (c_can_get_berr_counter [c_can]) from [<bf010294>] (can_fill_info+0x124/0x15c [can_dev]) [ 16.963480] r5:ec8c9740 r4:ed3d3000 [ 16.967253] [<bf010170>] (can_fill_info [can_dev]) from [<c0502fa8>] (rtnl_fill_ifinfo+0x58c/0x8fc) [ 16.976749] r6:ec8c9740 r5:ed3d3000 r4:eb2b6780 [ 16.981613] [<c0502a1c>] (rtnl_fill_ifinfo) from [<c0503408>] (rtnl_dump_ifinfo+0xf0/0x1dc) [ 16.990401] r10:ec8c9740 r9:00000000 r8:00000000 r7:00000000 r6:ebd4d1b4 r5:ed3d3000 [ 16.998671] r4:00000000 [ 17.001342] [<c0503318>] (rtnl_dump_ifinfo) from [<c050e6e4>] (netlink_dump+0xa8/0x1e0) [ 17.009772] r10:00000000 r9:00000000 r8:c0503318 r7:ebf3e6c0 r6:ebd4d1b4 r5:ec8c9740 [ 17.018050] r4:ebd4d000 [ 17.020714] [<c050e63c>] (netlink_dump) from [<c050ec10>] (__netlink_dump_start+0x104/0x154) [ 17.029591] r6:eab5bd34 r5:ec8c9980 r4:ebd4d000 [ 17.034454] [<c050eb0c>] (__netlink_dump_start) from [<c0505604>] (rtnetlink_rcv_msg+0x110/0x1f4) [ 17.043778] r7:00000000 r6:ec8c9980 r5:00000f40 r4:ebf3e6c0 [ 17.049743] [<c05054f4>] (rtnetlink_rcv_msg) from [<c05108e8>] (netlink_rcv_skb+0xb4/0xc8) [ 17.058449] r8:eab5bdac r7:ec8c9980 r6:c05054f4 r5:ec8c9980 r4:ebf3e6c0 [ 17.065534] [<c0510834>] (netlink_rcv_skb) from [<c0504134>] (rtnetlink_rcv+0x24/0x2c) [ 17.073854] r6:ebd4d000 r5:00000014 r4:ec8c9980 r3:c0504110 [ 17.079846] [<c0504110>] (rtnetlink_rcv) from [<c05102ac>] (netlink_unicast+0x180/0x1ec) [ 17.088363] r4:ed0c6800 r3:c0504110 [ 17.092113] [<c051012c>] (netlink_unicast) from [<c0510670>] (netlink_sendmsg+0x2ac/0x380) [ 17.100813] r10:00000000 r8:00000008 r7:ec8c9980 r6:ebd4d000 r5:eab5be70 r4:eab5bee4 [ 17.109083] [<c05103c4>] (netlink_sendmsg) from [<c04dfdb4>] (sock_sendmsg+0x90/0xb0) [ 17.117305] r10:00000000 r9:eab5a000 r8:becdda3c r7:0000000c r6:ea978400 r5:eab5be70 [ 17.125563] r4:c05103c4 [ 17.128225] [<c04dfd24>] (sock_sendmsg) from [<c04e1c28>] (SyS_sendto+0xb8/0xdc) [ 17.136001] r6:becdda5c r5:00000014 r4:ecd37040 [ 17.140876] [<c04e1b70>] (SyS_sendto) from [<c000e680>] (ret_fast_syscall+0x0/0x30) [ 17.148923] r10:00000000 r8:c000e804 r7:00000122 r6:becdda5c r5:0000000c r4:becdda5c [ 17.157169] ---[ end trace 2b71e15b38f58bad ]--- Fixes: 6423d6df ("ARM: OMAP2+: hwmod: check for module address space during init") Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: <stable@vger.kernel.org>
-
- 21 Jul, 2015 3 commits
-
-
Olof Johansson authored
Merge tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes Merge "Samsung fixes for v4.2" from Kukjin Kim: From Krzysztof Kozlowski: 1. Fix exynos3250 MIPI DSI display and MIPI CSIS-2 camera sensorx after adding support for PMU regmap in exynos-video-mipi driver (issue introduced in v4.0). 2. Bring back cpufreq for exynos4210 after incomplete switch to cpufreq-dt driver in 4.2 merge window. The necessary DT changes for exynos4210 cpufreq was not applied to the same tree as rest of patchset because of multiple conflicts between clk and arm-soc trees. Unfortunately without the change the exynos4210 boards loose cpufreq feature. * tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: ARM: dts: add CPU OPP and regulator supply property for exynos4210 ARM: dts: Update video-phy node with syscon phandle for exynos3250 Signed-off-by: Olof Johansson <olof@lixom.net>
-
Thomas Abraham authored
For Exynos4210 platforms, add CPU operating points and CPU regulator supply properties for migrating from Exynos specific cpufreq driver to using generic cpufreq driver. Cc: Doug Anderson <dianders@chromium.org> Cc: Andreas Faerber <afaerber@suse.de> Cc: Sachin Kamat <sachin.kamat@linaro.org> Cc: Andreas Farber <afaerber@suse.de> Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> [b.zolnierkie: removed exynos5250 and exynos5420 support for now] Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> [k.kozlowski: Rebased, moved cpu nodes to alphabetical position] Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Kukjin Kim <kgene@kernel.org>
-
Beata Michalska authored
As a follow-up to recent changes to Exynos mipi video phy driver, introducing support for PMU regmap in commit e4b3d380 ("phy: exynos-video-mipi: Fix regression by adding support for PMU regmap") add a syscon phandle to video-phy node to bring back to life both MIPI DSI display and MIPI CSIS-2 camera sensor on Exynos3250. Signed-off-by: Beata Michalska <b.michalska@samsung.com> Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Kukjin Kim <kgene@kernel.org>
-
- 19 Jul, 2015 1 commit
-
-
https://github.com/rjarzmik/linuxOlof Johansson authored
Merge "pxa fixes for v4.2" from Robert Jarzmik: ARM: pxa: fixes for v4.2-rc2 This single fix reenables ethernet cards for several pxa boards, broken by regulator addition to dm9000 driver. * tag 'pxa-fixes-v4.2-rc2' of https://github.com/rjarzmik/linux: ARM: pxa: fix dm9000 platform data regression
-
- 17 Jul, 2015 1 commit
-
-
Olof Johansson authored
Merge tag 'keystone-dts-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into fixes Merge "ARM: Couple of dts fixes for v4.2-rcx" from Santosh Shilimkar: Couple of DTS fixes 4.2-rcx for Keystone EVMs: K2E EVM boot hangs because of missing serdes driver which is needed to bring up PCIe on K2E. These couple of fixes makes the PCIE disabled on common default and let the specific board DTS to enable it. * tag 'keystone-dts-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone: ARM: keystone: dts: rename pcie nodes to help override status ARM: keystone: dts: fix dt bindings for PCIe Signed-off-by: Olof Johansson <olof@lixom.net>
-
- 16 Jul, 2015 3 commits
-
-
Murali Karicheri authored
Now that PCIe DT binding is disabled in SoC specific DTS, we need a way to override it in a board specific DTS. So rename the PCIe nodes accordingly. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
-
Murali Karicheri authored
Currently PCIe DT bindings are broken. PCIe driver can't function without having a SerDes driver that provide the phy configuration. On K2E EVM, this causes problem since the EVM has Marvell SATA controller present and with default values in the SerDes register, it seems to pass the PCIe link check, but causes issues since the configuration is not correct. The manifestation is that when EVM is booted with NFS rootfs, the boot hangs. We shouldn't enable PCIe on this EVM since to work, SerDes driver has to be present as well. So by default, the PCIe DT binding should be disabled in SoC specific DTS. It can be enabled in the board specific DTS when the SerDes device driver is also present. So fix the status of PCIe DT bindings in the SoC specific DTS to "disabled". To enable PCIe, the status should be set to "ok" in the EVM DTS file when SerDes driver support becomes available in the upstream tree. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
-
Robert Jarzmik authored
Since dm9000 driver added support for a vcc regulator, platform data based platforms have their ethernet broken, as the regulator claiming returns -EPROBE_DEFER and prevents dm9000 loading. This patch fixes this for all pxa boards using dm9000, by using the specific regulator_has_full_constraints() function. This was discovered and tested on the cm-x300 board. Fixes: 7994fe55 ("dm9000: Add regulator and reset support to dm9000") Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
-
- 15 Jul, 2015 5 commits
-
-
Roger Quadros authored
GPMC smart idle is not really broken but it does not support smart idle with wakeup. Fixes: 556708fe ("ARM: OMAP: DRA7: hwmod: Make gpmc software supervised as the smart idle is broken") Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
-
Olof Johansson authored
Merge tag 'omap-for-v4.2/fixes-rc2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes Fixes for omaps, all dts changes except for one: - Fix up LCD panel name for overo boards - Three fixes for pepper board for regulators, freqeuncy scaling and audio input. Note that there is still one issue being worked on for booting with multi_v7_defconfig - Add missing #iommu-cells for omap4 and 5 - Add missing HAVE_ARM_SCU for am43xx * tag 'omap-for-v4.2/fixes-rc2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (210 commits) ARM: dts: Correct audio input route & set mic bias for am335x-pepper ARM: OMAP2+: Add HAVE_ARM_SCU for AM43XX ARM: dts: OMAP5: Add #iommu-cells property to IOMMUs ARM: dts: OMAP4: Add #iommu-cells property to IOMMUs ARM: dts: Fix frequency scaling on Gumstix Pepper ARM: dts: configure regulators for Gumstix Pepper ARM: dts: omap3: overo: Update LCD panel names + Linux 4.2-rc2 Signed-off-by: Olof Johansson <olof@lixom.net>
-
Adam YH Lee authored
Audio-in was incorrectly routed to Line In. It should be Mic3L as per schematic. Using mic-bias voltage at 2.0v (<0x1>) does not work for some reason. There is no voltage seen on micbias (R127). Mic-bias voltage of 2.5v (<0x2>) works. I see voltage of 2.475v across GND and micbias. With these changes, I can record audio with a pair of proliferate TRRS earbuds. Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com> Acked-by: Ash Charles <ashcharles@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Dave Gerlach authored
CONFIG_HAVE_ARM_SCU only gets selected if CONFIG_SMP is selected in an OMAP system, however AM43XX needs this option regardless of CONFIG_SMP and also for an AM43XX only build as it is important for controlling power in the SoC. Without this we cannot suspend the CPU for SoC suspend or cpuidle. The ARM Cortex A9 needs SCU CPU Power Status bits to be set to off mode in order for the PRCM to transition the MPU to low power modes. Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Olof Johansson authored
Merge tag 'imx-fixes-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes Merge "ARM: imx: fixes for 4.2" from Shawn Guo: The i.MX fixes for 4.2: - Correct compatible string for i.MX27 GPT which actually shares the same programming model as i.MX21 GPT rather than i.MX1 one. - Add missing #io-channel-cells property for i.MX23 LRADC device, which is required for the device to be an IIO provider. - Correct HSYNC/VSYNC pins and add ddc-i2c-bus property for TVE device on imx53-qsb to work properly. - Always enable PU domain if CONFIG_PM is not set. This fixes a couple of failure scenarios which will hang the system if one of the devices in the PU domain is accessed. * tag 'imx-fixes-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: ARM: imx6: gpc: always enable PU domain if CONFIG_PM is not set ARM: dts: imx53-qsb: fix TVE entry ARM: dts: mx23: fix iio-hwmon support ARM: dts: imx27: Adjust the GPT compatible string Signed-off-by: Olof Johansson <olof@lixom.net>
-
- 14 Jul, 2015 9 commits
-
-
Baruch Siach authored
The 'digicolor' regexp doesn't cover the dts files. Add a glob pattern for them. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Olof Johansson <olof@lixom.net>
-
Olof Johansson authored
Merge tag 'socfpga_fixes_for_v4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into fixes Merge "SoCFPGA fixes for v4.2-rc1" from Dinh Nguyen: SoCFPGA fixes against v4.2-rc1 - Update compatible "adxl345x" compatible string - Alphabetize the DTS nodes for the C5 sockit board file * tag 'socfpga_fixes_for_v4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: ARM: socfpga: dts: Fix entries order ARM: socfpga: dts: Fix adxl34x formating and compatible string
-
Linus Walleij authored
Ux500 is regressing due to commit a21763a0 "pinctrl: nomadik: activate strict mux mode" which disallows Nomadik GPIO 5 to be muxed in as a level shifter voltage select pin, as it is currently described as being used for RX on UART1. The behaviour is correct, instead the hardware config has been incorrecly specified: UART1 is indeed unused on HREFv60plus and Snowball and that is why HREFv60plus can use the pins it would normally occupy as the voltage select line for the MMC/SD levelshifter (Snowball uses it for I2C4). The reason UART1 was anyway enabled on these platforms was probably to secure the port enumeration to userspace. This can be solved by using aliases (done in a separate patch) so we can now deactivate UART1 and let MMC/SD use it properly on HREFv60plus. We explicitly activate it only for the older HREFprev60 board. To complete, we set up the pin configuration for these pins properly in the sdi0 node. Cc: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
-
Linus Walleij authored
This enumerates the PL011 serial ports on the Ux500. This is necessary to do if we want to remove one of the serial ports, since userspace depends on console to be present on ttyAMA2 and we must not break userspace. Cc: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
-
Suman Anna authored
Add missing #iommu-cells property to the DSP and IPU IOMMU nodes for OMAP5 platforms. This property is required as per the generic iommu binding. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Suman Anna authored
Add missing #iommu-cells property to the DSP and IPU IOMMU nodes for OMAP4 platforms. This property is required as per the generic iommu binding. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Arun Bharadwaj authored
The device tree for Gumstix Pepper has DCDC2 and DCDC3 correctly labelled but the upper limit values are wrong. The confusion is due to the hardware quirk where the DCDC2 and DCDC3 wires are flipped in Pepper. Signed-off-by: Arun Bharadwaj <arun@gumstix.com> Tested-by: Ash Charles <ashcharles@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Adam YH Lee authored
Boot process is halting in midway because some of the necessary voltage regulators are deemed unused and subsequently powered off, leading to a completely unresponsive system. Most of the device nodes had correct voltage regulator attachments. Yet these nodes had to set stricter enforcement on them through 'regulator-boot-on' and 'regulator-always-on' to function correctly. The consumers of the regulators this commit affect are the followings: DCDC1: vdd_1v8 system supply, USB-PHY, and ADC DCDC2: Core domain DCDC3: MPU core domain LDO1: RTC LDO2: 3v3 IO domain LDO3: USB-PHY; not a boot-time requirement LDO4: LCD [16:23] All but LDO3 need to be always-on for the system to be functional. Additionally regulator-name properties have been added for the kernel to display the name from the schematic. This will improve diagnostics. Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Adam YH Lee authored
For Gumstix Overo COMs, the u-boot bootloader typically passes an argument specifying the default display via the omapdss.def_disp parameter. When a default display is specified, DSS2 tries to match this name with either the device tree label (e.g. label=dvi) or, failing this, the device tree alias (e.g. label=display0). Update the panel names for the 'lcd43' and 'lcd35' displays in the device tree such that they match the names passed by u-boot. Signed-off-by: Ash Charles <ashcharles@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 13 Jul, 2015 1 commit
-
-
Chris Zhong authored
Add support for 4 Japanese keys Signed-off-by: Chris Zhong <zyw@rock-chips.com> Reviewed-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Olof Johansson <olof@lixom.net>
-
- 12 Jul, 2015 10 commits
-
-
Linus Torvalds authored
-
Linus Torvalds authored
This reverts commit dec4f799. Jörg Otte reports a NULL pointder dereference due to this commit, as 'crtc_state' very much can be NULL: crtc_state = state->base.state ? intel_atomic_get_crtc_state(state->base.state, intel_crtc) : NULL; So the change to test 'crtc_state->base.active' cannot possibly be correct as-is. There may be some other minimal fix (like just checking crtc_state for NULL), but I'm just reverting it now for the rc2 release, and people like Daniel Vetter who actually know this code will figure out what the right solution is in the longer term. Reported-and-bisected-by: Jörg Otte <jrg.otte@gmail.com> Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@intel.com> CC: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull VFS fixes from Al Viro: "Fixes for this cycle regression in overlayfs and a couple of long-standing (== all the way back to 2.6.12, at least) bugs" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: freeing unlinked file indefinitely delayed fix a braino in ovl_d_select_inode() 9p: don't leave a half-initialized inode sitting around
-
git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds authored
Pull MIPS fixes from Ralf Baechle: "A fair number of 4.2 fixes also because Markos opened the flood gates. - Patch up the math used calculate the location for the page bitmap. - The FDC (Not what you think, FDC stands for Fast Debug Channel) IRQ around was causing issues on non-Malta platforms, so move the code to a Malta specific location. - A spelling fix replicated through several files. - Fix to the emulation of an R2 instruction for R6 cores. - Fix the JR emulation for R6. - Further patching of mindless 64 bit issues. - Ensure the kernel won't crash on CPUs with L2 caches with >= 8 ways. - Use compat_sys_getsockopt for O32 ABI on 64 bit kernels. - Fix cache flushing for multithreaded cores. - A build fix" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: MIPS: O32: Use compat_sys_getsockopt. MIPS: c-r4k: Extend way_string array MIPS: Pistachio: Support CDMM & Fast Debug Channel MIPS: Malta: Make GIC FDC IRQ workaround Malta specific MIPS: c-r4k: Fix cache flushing for MT cores Revert "MIPS: Kconfig: Disable SMP/CPS for 64-bit" MIPS: cps-vec: Use macros for various arithmetics and memory operations MIPS: kernel: cps-vec: Replace KSEG0 with CKSEG0 MIPS: kernel: cps-vec: Use ta0-ta3 pseudo-registers for 64-bit MIPS: kernel: cps-vec: Replace mips32r2 ISA level with mips64r2 MIPS: kernel: cps-vec: Replace 'la' macro with PTR_LA MIPS: kernel: smp-cps: Fix 64-bit compatibility errors due to pointer casting MIPS: Fix erroneous JR emulation for MIPS R6 MIPS: Fix branch emulation for BLTC and BGEC instructions MIPS: kernel: traps: Fix broken indentation MIPS: bootmem: Don't use memory holes for page bitmap MIPS: O32: Do not handle require 32 bytes from the stack to be readable. MIPS, CPUFREQ: Fix spelling of Institute. MIPS: Lemote 2F: Fix build caused by recent mass rename.
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Thomas Gleixner: - the high latency PIT detection fix, which slipped through the cracks for rc1 - a regression fix for the early printk mechanism - the x86 part to plug irq/vector related hotplug races - move the allocation of the espfix pages on cpu hotplug to non atomic context. The current code triggers a might_sleep() warning. - a series of KASAN fixes addressing boot crashes and usability - a trivial typo fix for Kconfig help text * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/kconfig: Fix typo in the CONFIG_CMDLINE_BOOL help text x86/irq: Retrieve irq data after locking irq_desc x86/irq: Use proper locking in check_irq_vectors_for_cpu_disable() x86/irq: Plug irq vector hotplug race x86/earlyprintk: Allow early_printk() to use console style parameters like '115200n8' x86/espfix: Init espfix on the boot CPU side x86/espfix: Add 'cpu' parameter to init_espfix_ap() x86/kasan: Move KASAN_SHADOW_OFFSET to the arch Kconfig x86/kasan: Add message about KASAN being initialized x86/kasan: Fix boot crash on AMD processors x86/kasan: Flush TLBs after switching CR3 x86/kasan: Fix KASAN shadow region page tables x86/init: Clear 'init_level4_pgt' earlier x86/tsc: Let high latency PIT fail fast in quick_pit_calibrate()
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull timer fixes from Thomas Gleixner: "This update from the timer departement contains: - A series of patches which address a shortcoming in the tick broadcast code. If the broadcast device is not available or an hrtimer emulated broadcast device, some of the original assumptions lead to boot failures. I rather plugged all of the corner cases instead of only addressing the issue reported, so the change got a little larger. Has been extensivly tested on x86 and arm. - Get rid of the last holdouts using do_posix_clock_monotonic_gettime() - A regression fix for the imx clocksource driver - An update to the new state callbacks mechanism for clockevents. This is required to simplify the conversion, which will take place in 4.3" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: tick/broadcast: Prevent NULL pointer dereference time: Get rid of do_posix_clock_monotonic_gettime cris: Replace do_posix_clock_monotonic_gettime() tick/broadcast: Unbreak CONFIG_GENERIC_CLOCKEVENTS=n build tick/broadcast: Handle spurious interrupts gracefully tick/broadcast: Check for hrtimer broadcast active early tick/broadcast: Return busy when IPI is pending tick/broadcast: Return busy if periodic mode and hrtimer broadcast tick/broadcast: Move the check for periodic mode inside state handling tick/broadcast: Prevent deep idle if no broadcast device available tick/broadcast: Make idle check independent from mode and config tick/broadcast: Sanity check the shutdown of the local clock_event tick/broadcast: Prevent hrtimer recursion clockevents: Allow set-state callbacks to be optional clocksource/imx: Define clocksource for mx27
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull irq fix from Thomas Gleixner: "A single fix for a cpu hotplug race vs. interrupt descriptors: Prevent irq setup/teardown across the cpu starting/dying parts of cpu hotplug so that the starting/dying cpu has a stable view of the descriptor space. This has been an issue for all architectures in the cpu dying phase, where interrupts are migrated away from the dying cpu. In the starting phase its mostly a x86 issue vs the vector space update" * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: hotplug: Prevent alloc/free of irq descriptors during cpu up/down
-
Al Viro authored
Normally opening a file, unlinking it and then closing will have the inode freed upon close() (provided that it's not otherwise busy and has no remaining links, of course). However, there's one case where that does *not* happen. Namely, if you open it by fhandle with cold dcache, then unlink() and close(). In normal case you get d_delete() in unlink(2) notice that dentry is busy and unhash it; on the final dput() it will be forcibly evicted from dcache, triggering iput() and inode removal. In this case, though, we end up with *two* dentries - disconnected (created by open-by-fhandle) and regular one (used by unlink()). The latter will have its reference to inode dropped just fine, but the former will not - it's considered hashed (it is on the ->s_anon list), so it will stay around until the memory pressure will finally do it in. As the result, we have the final iput() delayed indefinitely. It's trivial to reproduce - void flush_dcache(void) { system("mount -o remount,rw /"); } static char buf[20 * 1024 * 1024]; main() { int fd; union { struct file_handle f; char buf[MAX_HANDLE_SZ]; } x; int m; x.f.handle_bytes = sizeof(x); chdir("/root"); mkdir("foo", 0700); fd = open("foo/bar", O_CREAT | O_RDWR, 0600); close(fd); name_to_handle_at(AT_FDCWD, "foo/bar", &x.f, &m, 0); flush_dcache(); fd = open_by_handle_at(AT_FDCWD, &x.f, O_RDWR); unlink("foo/bar"); write(fd, buf, sizeof(buf)); system("df ."); /* 20Mb eaten */ close(fd); system("df ."); /* should've freed those 20Mb */ flush_dcache(); system("df ."); /* should be the same as #2 */ } will spit out something like Filesystem 1K-blocks Used Available Use% Mounted on /dev/root 322023 303843 1131 100% / Filesystem 1K-blocks Used Available Use% Mounted on /dev/root 322023 303843 1131 100% / Filesystem 1K-blocks Used Available Use% Mounted on /dev/root 322023 283282 21692 93% / - inode gets freed only when dentry is finally evicted (here we trigger than by remount; normally it would've happened in response to memory pressure hell knows when). Cc: stable@vger.kernel.org # v2.6.38+; earlier ones need s/kill_it/unhash_it/ Acked-by: J. Bruce Fields <bfields@fieldses.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
when opening a directory we want the overlayfs inode, not one from the topmost layer. Reported-By: Andrey Jr. Melnikov <temnota.am@gmail.com> Tested-By: Andrey Jr. Melnikov <temnota.am@gmail.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
Cc: stable@vger.kernel.org # all branches Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-