Non-PCI devices can use the entire 32-bit range, PCI dittos are
limited to the first 64MiB.

Also actually setup coherent_dma_mask.

The patch has been verified on a board with 128MiB memory, one
ipx4xx_eth device and a e100 PCI device.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This patch fixes the following BUG:

> kernel BUG at mm/vmalloc.c:1132!
> PC is at vm_area_add_early+0x20/0x84
> LR is at add_static_vm_early+0xc/0x60
>
> The problem is cns3xxx_pcie_init() (device_initcall) calls the "early"
> iotable_init().

Instead of merely calling the PCIe iotable_init() from
machine_desc->map_io(), this patch adds the required mappings to the
main CNS3xxx mapping table. This means we don't convert .pfn back to
virtual addresses in pcie.c. The size of the address space consumed for
PCIe control is reduced from 96 MiB (6 * 16 MiB) to about 32 MiB (this
doesn't include MMIO address space required by PCI devices):

- Size of the PCIe "host" mapping is reduced from 16 MiB to 4 KiB.
  It's a PCI configuration address space for the local (on-chip) PCIe
  bridge.

- Size of the "CFG0" mapping is reduced from 16 MiB to 64 KiB. It's for
  Type 0 Configuration accesses, i.e., accesses to the single device
  (with possible "functions") on the other end of the PCIe link.
  We really only need a 4 KiB page at 0x8000 (see the offset
  calculation in cns3xxx_pci_cfg_base()). There is still a potential
  problem with PCI bus numbers > 0xF, are they supported?

- The code in cns3xxx_pci_cfg_base() and cns3xxx_pcie_hw_init() should
  be clearer now.

- The maximum address space allocated for PCI MMIO is now correctly
  shown in /proc/iomem as 176 MiB (per each of the two PCI "domains"
  - previously only 16 MiB were reserved).

This patch has been tested on Gateworks Laguna board, masqueraded as
CNS3420VB.
Signed-off-by: Krzysztof Ha?asa <khalasa@piap.pl>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

WARNING: at drivers/irqchip/irq-gic.c:952 gic_init_bases+0xe4/0x2b8()
Cannot allocate irq_descs @ IRQ16, assuming pre-allocated
Backtrace:
gic_init_bases    from cns3xxx_init_irq+0x24/0x34
cns3xxx_init_irq  from init_IRQ+0x24/0x2c
init_IRQ          from start_kernel+0x1a8/0x338
start_kernel      from 0x2000806c

The problem is that 64 CNS3xxx CPU interrupts, starting at 32, are
allocated by the ARM platform-independent code (as requested by
machine_desc->nr_irqs = 96), and then the GIC code tries to allocate
them again.

Tested on Gateworks Laguna board, masqueraded as CNS3420VB.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'omap-for-v3.15/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical

Merge "omap fixes for v3.15 merge window" from Tony Lindgren:

Fixes for omaps that would be good to get in before v3.15-rc1.

* tag 'omap-for-v3.15/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP4: hwmod data: correct the idlemodes for spinlock
  ARM: dts: am33xx: correcting dt node unit address for usb
  ARM: dts: omap4/5: Use l3_ick for the gpmc node
  CLK: TI: OMAP4/5/DRA7: Remove gpmc_fck from dummy clocks
  ARM: OMAP4: Fix definition of IS_PM44XX_ERRATUM
  ARM: OMAP2+: INTC: Acknowledge stuck active interrupts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The spinlock module's SYSCONFIG register does not support
smart wakeup, so remove this flag from the idle modes in
the spinlock hwmod definition.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

DT node's unit address should be its own register offset address to make it a
unique across the system. This patch corrects the incorrect USB entries with
correct register offset for unit address.

Cc: stable@vger.kernel.org # v3.12+
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The GPMC clock is derived from l3_ick. The simplest solution is
to reference directly l3_ick to provide the GPMC fck in order to
get correct timings. The real management of the clock is left to
hwmod.

Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>

When arch/arm/mach-omap2/gpmc.c calls clk_get(..., "fck"), it will
get a dummy clock and try to use it. As the rate is configured to zero,
this will result in several divisions by zero, and misconfigured
timings, with devices on the bus being lost in the La La Land.

It is better to remove gpmc_fck from the dummy clocks, so that gpmc.c
can fail gracefully.

Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Just like IS_PM34XX_ERRATUM, IS_PM44XX_ERRATUM is valid only if
CONFIG_PM is enabled, else, disabling CONFIG_PM results in build
failure complaining about the following:
arch/arm/mach-omap2/built-in.o: In function `omap4_boot_secondary':
:(.text+0x8a70): undefined reference to `pm44xx_errata'

Fixes: c9621844 (ARM: OMAP4: PM: add errata support)
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.ocm>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

When an interrupt has become active on the INTC it will stay active
until it is acked, even if masked or de-asserted. The
INTC_PENDING_IRQn registers are however updated and since these are
used by omap_intc_handle_irq to determine which interrupt to handle,
it will never see the active interrupt. This will result in a storm of
useless interrupts that is only stopped when another higher priority
interrupt is asserted.

Fix by sending the INTC an acknowledge if we find no interrupts to
handle.

Cc: stable@vger.kernel.org
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

When sending an SGI to another CPU, we require a barrier to ensure that
any pending stores to normal memory are made visible to the recipient
before the interrupt arrives.

Rather than use a vanilla dsb() (which will soon cause an assembly error
on arm64) before the writel_relaxed, we can instead use dsb(ishst),
since we just need to ensure that any pending normal writes are visible
within the inner-shareable domain before we poke the GIC.

With this observation, we can then further weaken the barrier to a
dmb(ishst), since other CPUs in the inner-shareable domain must observe
the write to the distributor before the SGI is generated.

Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Pull ARM SoC fixes from Olof Johansson:
 "A collection of fixes for ARM platforms.  Most are fixes for DTS
  files, mostly from DT conversion on OMAP which is still finding a few
  issues here and there.

  There's a couple of small stale code removal patches that we usually
  queue for the next release instead, but they seemed harmless enough to
  bring in now.

  Also, a fix for backlight on some PXA platforms, and a cache
  configuration fix for Tegra, etc"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
  MAINTAINERS: add additional ARM BCM281xx/BCM11xxx maintainer
  ARM: tegra: only run PL310 init on systems with one
  ARM: tegra: Add head numbers to display controllers
  ARM: imx6: build pm-imx6q.c independently of CONFIG_PM
  ARM: tegra: fix RTC0 alias for Cardhu
  ARM: dove: dt: revert PMU interrupt controller node
  Documentation: dt: OMAP: Update Overo/Tobi
  ARM: dts: Add support for both OMAP35xx and OMAP36xx Overo/Tobi
  ARM: dts: omap3-tobi: Use the correct vendor prefix
  ARM: dts: omap3-tobi: Fix boot with OMAP36xx-based Overo
  ARM: OMAP2+: Remove legacy macros for zoom platforms
  ARM: OMAP2+: Remove MACH_NOKIA_N800
  ARM: dts: N900: add missing compatible property
  ARM: dts: N9/N950: fix boot hang with 3.14-rc1
  ARM: OMAP1: nokia770: enable tahvo-usb
  ARM: OMAP2+: gpmc: fix: DT ONENAND child nodes not probed when MTD_ONENAND is built as module
  ARM: OMAP2+: gpmc: fix: DT NAND child nodes not probed when MTD_NAND is built as module
  ARM: dts: omap3-gta04: Fix mmc1 properties.
  ARM: dts: omap3-gta04: Fix 'aux' gpio key flags.
  ARM: OMAP2+: add missing ARCH_HAS_OPP
  ...

Pull regulator fixes from Mark Brown:
 "Mostly unexciting driver fixes, plus one fix to lower the severity of
  the log message when we don't use an optional regulator - the fixes
  for ACPI system made this come up more often and it was correctly
  observed that it was causing undue concern for users"

* tag 'regulator-v3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: max14577: Fix invalid return value on DT parse success
  regulator: core: Change dummy supplies error message to a warning
  regulator: s5m8767: Add missing of_node_put
  regulator: s5m8767: Use of_get_child_by_name
  regulator: da9063: Bug fix when setting max voltage on LDOs 5-11

Pull timer fix from Thomas Gleixner:
 "Serialize the registration of a new sched_clock in the currently ARM
  only generic sched_clock facilty to avoid sched_clock havoc"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched_clock: Prevent callers from seeing half-updated data

Pull x86 fixes from Thomas Gleixner:

 - a bugfix which prevents a divide by 0 panic when the newly introduced
   try_msr_calibrate_tsc() fails

 - enablement of the Baytrail platform to utilize the newfangled msr
   based calibration

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86: tsc: Add missing Baytrail frequency to the table
  x86, tsc: Fallback to normal calibration if fast MSR calibration fails

Pull irq fixes from Thomas Gleixner:
 "Another four fixlets to tame the ARM orion irq chip"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip: orion: Fix getting generic chip pointer.
  irqchip: orion: clear stale interrupts in irq_startup
  irqchip: orion: use handle_edge_irq on bridge irqs
  irqchip: orion: clear bridge cause register on init

Pull USB fixes from Greg KH:
 "Here are a number of USB fixes for reported issues for 3.14-rc4

  The majority of these are for USB gadget, phy, and musb driver issues.
  And there's a few new device ids thrown in for good measure"

* tag 'usb-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: chipidea: need to mask when writting endptflush and endptprime
  usb: musb: correct use of schedule_delayed_work()
  usb: phy: msm: fix compilation errors when !CONFIG_PM_SLEEP
  usb: gadget: fix NULL pointer dereference
  usb: gadget: printer: using gadget_is_otg to check otg support at runtime
  phy: let phy_provider_register be the last step in registering PHY
  phy-core: Don't allow building phy-core as a module
  phy-core: Don't propagate -ENOSUPP from phy_pm_runtime_get_sync to caller
  phy-core: phy_get: Leave error logging to the caller
  phy,phy-bcm-kona-usb2.c: Add dependency on HAS_IOMEM
  usb: musb: correct use of schedule_delayed_work()
  usb: musb: do not sleep in atomic context
  USB: serial: option: blacklist interface 4 for Cinterion PHS8 and PXS8
  USB: EHCI: add delay during suspend to prevent erroneous wakeups
  usb: gadget: bcm63xx_udc: fix build failure on DMA channel code
  usb: musb: do not sleep in atomic context
  usb: gadget: s3c2410_udc: Fix build error
  usb: musb: core: Fix remote-wakeup resume
  usb: musb: host: Fix SuperSpeed hub enumeration
  usb: musb: fix obex in g_nokia.ko causing kernel panic

Pull TTY revert from Greg KH:
 "Here is a single commit, a revert of a sysfs file change that ended up
  breaking a userspace tool"

* tag 'tty-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  Revert "tty: Set correct tty name in 'active' sysfs attribute"

Pull staging tree fix from Greg KH:
 "Here is a single android driver fix for 3.14-rc4 that fixes a reported
  problem in the binder driver"

* tag 'staging-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: binder: Fix death notifications

Pull char/misc fix from Greg KH:
 "Here is a single commit, to fix a reported problem in the mei driver"

* tag 'char-misc-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  mei: set client's read_cb to NULL when flow control fails

Add myself as an additional maintainer for the Broadcom mobile
SoCs.
Signed-off-by: Matt Porter <mporter@linaro.org>
Acked-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge remote-tracking branches 'regulator/fix/da9063', 'regulator/fix/max14577' and 'regulator/fix/s5m8767' into regulator-linus

This reverts commit d8a5dc30.

This breaks plymouth installs, either because plymouth is using the file
"incorrectly" or because the patch is incorrect.  Either way, this needs
to be reverted until it is all figured out.
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Reported-by: Ray Strode <halfline@gmail.com>
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Werner Fink <werner@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull scheduler fixes from Ingo Molnar:
 "Misc fixlets: a fair number of them resulting from the new
  SCHED_DEADLINE code"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/deadline: Remove useless dl_nr_total
  sched/deadline: Test for CPU's presence explicitly
  sched: Add 'flags' argument to sched_{set,get}attr() syscalls
  sched: Fix information leak in sys_sched_getattr()
  sched,numa: add cond_resched to task_numa_work
  sched/core: Make dl_b->lock IRQ safe
  sched/core: Fix sched_rt_global_validate
  sched/deadline: Fix overflow to handle period==0 and deadline!=0
  sched/deadline: Fix bad accounting of nr_running

Pull perf fixes from Ingo Molnar:
 "Misc fixlets from all around the place"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/uncore: Fix IVT/SNB-EP uncore CBOX NID filter table
  perf/x86: Correctly use FEATURE_PDCM
  perf, nmi: Fix unknown NMI warning
  perf trace: Fix ioctl 'request' beautifier build problems on !(i386 || x86_64) arches
  perf trace: Add fallback definition of EFD_SEMAPHORE
  perf list: Fix checking for supported events on older kernels
  perf tools: Handle PERF_RECORD_HEADER_EVENT_TYPE properly
  perf probe: Do not add offset twice to uprobe address
  perf/x86: Fix Userspace RDPMC switch
  perf/x86/intel/p6: Add userspace RDPMC quirk for PPro

Pull hwmon fix from Guenter Roeck:
 "Fix writing the minimum temperature in max1668 driver"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (max1668) Fix writing the minimum temperature

Pull xfs fixes from Dave Chinner:
 "This is the first pull request I've had to do for you, so I'm still
  sorting things out.  The reason I'm sending this and not Ben should be
  obvious from the first commit below - SGI has stepped down from the
  XFS maintainership role.  As such, I'd like to take another
  opportunity to thank them for their many years of effort maintaining
  XFS and supporting the XFS community that they developed from the
  ground up.

  So I haven't had time to work things like signed tags into my
  workflows yet, so this is just a repo branch I'm asking you to pull
  from.  And yes, I named the branch -rc4 because I wanted the fixes in
  rc4, not because the branch was for merging into -rc3.  Probably not
  right, either.

  Anyway, I should have everything sorted out by the time the next merge
  window comes around.  If there's anything that you don't like in the
  pull req, feel free to flame me unmercifully.

  The changes are fixes for recent regressions and important thinkos in
  verification code:

        - a log vector buffer alignment issue on ia32
        - timestamps on truncate got mangled
        - primary superblock CRC validation fixes and error message
          sanitisation"

* 'xfs-fixes-for-3.14-rc4' of git://oss.sgi.com/xfs/xfs:
  xfs: limit superblock corruption errors to actual corruption
  xfs: skip verification on initial "guess" superblock read
  MAINTAINERS: SGI no longer maintaining XFS
  xfs: xfs_sb_read_verify() doesn't flag bad crcs on primary sb
  xfs: ensure correct log item buffer alignment
  xfs: ensure correct timestamp updates from truncate

Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent

Pull perf/urgent fixes from Arnaldo Carvalho de Melo:

  * Handle PERF_RECORD_HEADER_EVENT_TYPE properly. (Jiri Olsa)

  * Fix checking for supported events on older kernels in
    'perf list' (Vince Weaver)

  * Do not add offset twice to uprobe address in
    'perf probe' (Masami Hiramatsu)

  * Fix perf trace's ioctl 'request' beautifier build problems
    on !(i386 || x86_64) arches (Arnaldo Carvalho de Melo)

  * Fix 'perf trace' build by adding a fallback definition for
    EFD_SEMAPHORE (Ben Hutchings)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>

This fixes bug introduced in 667a6b7a (regulator: max14577: Add missing
of_node_put). The DTS parsing function returned number of matched
regulators as success status which then was compared against 0 in probe.

Result was a probe fail after successful parsing the DTS:
max14577-regulator: probe of max14577-regulator failed with error 2
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviwed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

irqchip mvebu fixes for v3.14

 - orion:
    - fixes for clearing bridge cause register, and clearing stale interrupts
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Pull devicetree fixes from Grant Likely:
 "Device tree compatible match order bug fix

  This branch contains a bug fix for the way devicetree code identifies
  the type of device.  Device drivers can contain a list of
  of_device_ids, but it more than one entry will match, then the device
  driver may choose the wrong one.  Commit 10535314, "match each node
  compatible against all given matches first", was queued for v3.14 but
  ended up causing other bugs.  Commit 06b29e76 attempted to fix it
  but it had other bugs.  Merely reverting the fix and waiting until
  v3.15 isn't a good option because there is code in v3.14 that depends
  on the revised behaviour to boot.

  This branch should finally fixes the problem correctly.  This time
  instead of just hoping that the patch is correct, this branch also
  adds new testcases that validate the behaviour.

  The changes in this branch are larger than I would like for a -rc
  pull, but moving the test case data out of out of arch/arm so that it
  could be validated on other architectures was important"

* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
  of: Add self test for of_match_node()
  of: Move testcase FDT data into drivers/of
  of: reimplement the matching method for __of_match_node()
  Revert "of: search the best compatible match first in __of_match_node()"

Pull watchdog fix from Wim Van Sebroeck:
 "It corrects the error code when no device was found for w83697hf_wdt"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: w83697hf_wdt: return ENODEV if no device was found

Enabling SPARSE_IRQ shows up a bug in the irq-orion bridge interrupt
handler. The bridge interrupt is implemented using a single generic
chip. Thus the parameter passed to irq_get_domain_generic_chip()
should always be zero.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Fixes: 9dbd90f1 ("irqchip: Add support for Marvell Orion SoCs")
Cc: <stable@vger.kernel.org> # v3.11+
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This patch updates the CBOX PMU filters mapping tables for SNB-EP
and IVT (model 45 and 62 respectively).

The NID umask always comes in addition to another umask.
When set, the NID filter is applied.

The current mapping tables were missing some code/umask
combinations to account for the NID umask. This patch
fixes that.

Cc: mingo@elte.hu
Cc: ak@linux.intel.com
Reviewed-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140219131018.GA24475@quadSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

The current code simply assumes Intel Arch PerfMon v2+ to have
the IA32_PERF_CAPABILITIES MSR; the SDM specifies that we should check
CPUID[1].ECX[15] (aka, FEATURE_PDCM) instead.

This was found by KVM which implements v2+ but didn't provide the
capabilities MSR. Change the code to DTRT; KVM will also implement the
MSR and return 0.

Cc: pbonzini@redhat.com
Reported-by: "Michael S. Tsirkin" <mst@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140203132903.GI8874@twins.programming.kicks-ass.netSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

When using BTS on Core i7-4*, I get the below kernel warning.

$ perf record -c 1 -e branches:u ls
Message from syslogd@labpc1501 at Nov 11 15:49:25 ...
 kernel:[  438.317893] Uhhuh. NMI received for unknown reason 31 on CPU 2.

Message from syslogd@labpc1501 at Nov 11 15:49:25 ...
 kernel:[  438.317920] Do you have a strange power saving mode enabled?

Message from syslogd@labpc1501 at Nov 11 15:49:25 ...
 kernel:[  438.317945] Dazed and confused, but trying to continue

Make intel_pmu_handle_irq() take the full exit path when returning early.

Cc: eranian@google.com
Cc: peterz@infradead.org
Cc: mingo@kernel.org
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1392425048-5309-1-git-send-email-andi@firstfloor.orgSigned-off-by: Thomas Gleixner <tglx@linutronix.de>