- 20 Nov, 2016 40 commits
-
-
Radim Krčmář authored
commit dccbfcf5 upstream. If vmcs12 does not intercept APIC_BASE writes, then KVM will handle the write with vmcs02 as the current VMCS. This will incorrectly apply modifications intended for vmcs01 to vmcs02 and L2 can use it to gain access to L0's x2APIC registers by disabling virtualized x2APIC while using msr bitmap that assumes enabled. Postpone execution of vmx_set_virtual_x2apic_mode until vmcs01 is the current VMCS. An alternative solution would temporarily make vmcs01 the current VMCS, but it requires more care. Fixes: 8d14695f ("x86, apicv: add virtual x2apic support") Reported-by:
Jim Mattson <jmattson@google.com> Reviewed-by:
Wanpeng Li <wanpeng.li@hotmail.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Mathias Nyman authored
commit f1f6d9a8 upstream. Remove the hcd after checking for the xhci last quirks, not before. This caused a hang on a Alpine Ridge xhci based maching which remove the whole xhci controller when unplugging the last usb device Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.16: adjust context] Signed-off-by:
-
Jim Lin authored
commit 88716a93 upstream. After a device is disconnected, xhci_stop_device() will be invoked in xhci_bus_suspend(). Also the "disconnect" IRQ will have ISR to invoke xhci_free_virt_device() in this sequence. xhci_irq -> xhci_handle_event -> handle_cmd_completion -> xhci_handle_cmd_disable_slot -> xhci_free_virt_device If xhci->devs[slot_id] has been assigned to NULL in xhci_free_virt_device(), then virt_dev->eps[i].ring in xhci_stop_device() may point to an invlid address to cause kernel panic. virt_dev = xhci->devs[slot_id]; : if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue) [] Unable to handle kernel paging request at virtual address 00001a68 [] pgd=ffffffc001430000 [] [00001a68] *pgd=000000013c807003, *pud=000000013c807003, *pmd=000000013c808003, *pte=0000000000000000 [] Internal error: Oops: 96000006 [#1] PREEMPT SMP [] CPU: 0 PID: 39 Comm: kworker/0:1 Tainted: G U [] Workqueue: pm pm_runtime_work [] task: ffffffc0bc0e0bc0 ti: ffffffc0bc0ec000 task.ti: ffffffc0bc0ec000 [] PC is at xhci_stop_device.constprop.11+0xb4/0x1a4 This issue is found when running with realtek ethernet device (0bda:8153). Signed-off-by:
Jim Lin <jilin@nvidia.com> Signed-off-by:
-
Mathias Nyman authored
commit 33be1265 upstream. Fix "Command completion event does not match command" errors by always handling the command ring stopped events. The command ring stopped event is generated as a result of aborting or stopping the command ring with a register write. It is not caused by a command in the command queue, and thus won't have a matching command in the comman list. Solve it by handling the command ring stopped event before checking for a matching command. In most command time out cases we abort the command ring, and get a command ring stopped event. The events command pointer will point at the current command ring dequeue, which in most cases matches the timed out command in the command list, and no error messages are seen. If we instead get a command aborted event before the command ring stopped event, the abort event will increse the command ring dequeue pointer, and the following command ring stopped events command pointer will point at the next, not yet queued command. This case triggered the error message Signed-off-by:
-
Tyrel Datwyler authored
commit a87eeb90 upstream. Commit 655ee63c ("scsi constants: command, sense key + additional sense string") added a "Completed" sense string with key 0xF to snstext[], but failed to updated the upper bounds check of the sense key in scsi_sense_key_string(). Fixes: 655ee63c ("[SCSI] scsi constants: command, sense key + additional sense strings") Signed-off-by:
Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Reviewed-by:
Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> [bwh: Backported to 3.16: adjust context] Signed-off-by:
-
Anders Darander authored
commit c2ab4474 upstream. The driver always assumes that an input device has been created when reading channel 3. This causes a kernel panic when dereferencing st->ts_input. The change was introduced in commit 84882b06 ("iio: adc: at91_adc: Add support for touchscreens without TSMR"). Earlier versions only entered that part of the if-else statement if only the following flags are set: AT91_ADC_IER_XRDY | AT91_ADC_IER_YRDY | AT91_ADC_IER_PRDY Signed-off-by:
Anders Darander <anders@chargestorm.se> Acked-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Alison Schofield authored
commit f8adf645 upstream. Use the iio_pollfunc_store_time parameter during triggered buffer set-up to get valid timestamps. Signed-off-by:
Alison Schofield <amsfield22@gmail.com> Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by:
-
Gavin Li authored
commit add12505 upstream. This fixes the "BOGUS urb xfer" warning logged by usb_submit_urb(). Signed-off-by:
Gavin Li <git@thegavinli.com> Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
-
Alexey Khoroshilov authored
commit 3b7c7e52 upstream. There is an allocation with GFP_KERNEL flag in mos7840_write(), while it may be called from interrupt context. Follow-up for commit 19125283 ("USB: kobil_sct: fix non-atomic allocation in write path") Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Alexey Khoroshilov authored
commit 5a5a1d61 upstream. There is an allocation with GFP_KERNEL flag in mos7720_write(), while it may be called from interrupt context. Follow-up for commit 19125283 ("USB: kobil_sct: fix non-atomic allocation in write path") Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
-
Johannes Berg authored
commit c15c0ab1 upstream. Pass the correct type __wsum to csum_sub() and csum_add(). This doesn't really change anything since __wsum really *is* __be32, but removes the address space warnings from sparse. Cc: Eric Dumazet <edumazet@google.com> Fixes: 34ae6a1a ("ipv6: update skb->csum when CE mark is propagated") Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Thomas Garnier authored
commit 62822e2e upstream. Restore the processor state before calling any other functions to ensure per-CPU variables can be used with KASLR memory randomization. Tracing functions use per-CPU variables (GS based on x86) and one was called just before restoring the processor state fully. It resulted in a double fault when both the tracing & the exception handler functions tried to use a per-CPU variable. Fixes: bb3632c6 (PM / sleep: trace events for suspend/resume) Reported-and-tested-by:
Borislav Petkov <bp@suse.de> Reported-by:
Jiri Kosina <jikos@kernel.org> Tested-by:
Rafael J. Wysocki <rafael@kernel.org> Tested-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
Thomas Garnier <thgarnie@google.com> Acked-by:
Pavel Machek <pavel@ucw.cz> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Sven Van Asbroeck authored
commit 5381cfb6 upstream. The device's model download function returns the model data as an array of u32s, which is later compared to the reference model data. However, since the latter is an array of u16s, the comparison does not happen correctly, and model verification fails. This in turn breaks the POR initialization sequence. Fixes: 39e7213e ("max17042_battery: Support regmap to access device's registers") Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Sven Van Asbroeck <TheSven73@googlemail.com> Reviewed-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by:
Sebastian Reichel <sre@kernel.org> Signed-off-by:
-
James Hogan authored
commit 9b731bcf upstream. Propagate errors from kvm_mips_handle_kseg0_tlb_fault() and kvm_mips_handle_mapped_seg_tlb_fault(), usually triggering an internal error since they normally indicate the guest accessed bad physical memory or the commpage in an unexpected way. Fixes: 858dd5d4 ("KVM/MIPS32: MMU/TLB operations for the Guest.") Fixes: e685c689 ("KVM/MIPS32: Privileged instruction/target branch emulation.") Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: "Radim Krčmář" <rkrcmar@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Signed-off-by:
-
James Hogan authored
commit 0741f52d upstream. Two consecutive gfns are loaded into host TLB, so ensure the range check isn't off by one if guest_pmap_npages is odd. Fixes: 858dd5d4 ("KVM/MIPS32: MMU/TLB operations for the Guest.") Signed-off-by:
-
James Hogan authored
commit 8985d503 upstream. kvm_mips_handle_mapped_seg_tlb_fault() calculates the guest frame number based on the guest TLB EntryLo values, however it is not range checked to ensure it lies within the guest_pmap. If the physical memory the guest refers to is out of range then dump the guest TLB and emit an internal error. Fixes: 858dd5d4 ("KVM/MIPS32: MMU/TLB operations for the Guest.") Signed-off-by:
-
James Hogan authored
commit c604cffa upstream. kvm_mips_handle_mapped_seg_tlb_fault() appears to map the guest page at virtual address 0 to PFN 0 if the guest has created its own mapping there. The intention is unclear, but it may have been an attempt to protect the zero page from being mapped to anything but the comm page in code paths you wouldn't expect from genuine commpage accesses (guest kernel mode cache instructions on that address, hitting trapping instructions when executing from that address with a coincidental TLB eviction during the KVM handling, and guest user mode accesses to that address). Fix this to check for mappings exactly at KVM_GUEST_COMMPAGE_ADDR (it may not be at address 0 since commit 42aa12e7 ("MIPS: KVM: Move commpage so 0x0 is unmapped")), and set the corresponding EntryLo to be interpreted as 0 (invalid). Fixes: 858dd5d4 ("KVM/MIPS32: MMU/TLB operations for the Guest.") Signed-off-by:
-
Lu Baolu authored
commit 53958751 upstream. In sg_timeout(), req->status is set to "-ETIMEDOUT" before calling into usb_sg_cancel(). usb_sg_cancel() will do nothing and return directly if req->status has been set to a non-zero value. This will cause driver hang whenever transfer time out is triggered. This patch fixes this issue. It could be backported to stable kernel with version later than v3.15. Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Lu Baolu <baolu.lu@linux.intel.com> Suggested-by:
Alan Stern <stern@rowland.harvard.edu> Acked-by:
-
Dan Carpenter authored
commit 7442e6db upstream. The udc->eps[] array has USB_MAX_ENDPOINTS elements so > should be >=. Fixes: 3948f0e0 ('usb: add Freescale QE/CPM USB peripheral controller driver') Acked-by:
Peter Chen <peter.chen@nxp.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> [bwh: Backported to 3.16: adjust filename] Signed-off-by:
-
Yinghai Lu authored
commit e7f85168 upstream. Found one megaraid_sas HBA probe fails, [ 187.235190] scsi host2: Avago SAS based MegaRAID driver [ 191.112365] megaraid_sas 0000:89:00.0: BAR 0: can't reserve [io 0x0000-0x00ff] [ 191.120548] megaraid_sas 0000:89:00.0: IO memory region busy! and the card has resource like, [ 125.097714] pci 0000:89:00.0: [1000:005d] type 00 class 0x010400 [ 125.104446] pci 0000:89:00.0: reg 0x10: [io 0x0000-0x00ff] [ 125.110686] pci 0000:89:00.0: reg 0x14: [mem 0xce400000-0xce40ffff 64bit] [ 125.118286] pci 0000:89:00.0: reg 0x1c: [mem 0xce300000-0xce3fffff 64bit] [ 125.125891] pci 0000:89:00.0: reg 0x30: [mem 0xce200000-0xce2fffff pref] that does not io port resource allocated from BIOS, and kernel can not assign one as io port shortage. The driver is only looking for MEM, and should not fail. It turns out megasas_init_fw() etc are using bar index as mask. index 1 is used as mask 1, so that pci_request_selected_regions() is trying to request BAR0 instead of BAR1. Fix all related reference. Fixes: b6d5d880 ("megaraid_sas: Use lowest memory bar for SR-IOV VF support") Signed-off-by:
Yinghai Lu <yinghai@kernel.org> Acked-by:
Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by:
-
Dave Weinstein authored
commit 7de24996 upstream. Add access checks to sys_oabi_epoll_wait() and sys_oabi_semtimedop(). This fixes CVE-2016-3857, a local privilege escalation under CONFIG_OABI_COMPAT. Reported-by:
Chiachih Wu <wuchiachih@gmail.com> Reviewed-by:
Kees Cook <keescook@chromium.org> Reviewed-by:
Nicolas Pitre <nico@linaro.org> Signed-off-by:
Dave Weinstein <olorin@google.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Daniel Mentz authored
commit 18b43e89 upstream. trace_hardirqs_on_caller() in lockdep.c expects to be called before, not after interrupts are actually enabled. The following comment in kernel/locking/lockdep.c substantiates this claim: " /* * We're enabling irqs and according to our state above irqs weren't * already enabled, yet we find the hardware thinks they are in fact * enabled.. someone messed up their IRQ state tracing. */ " An example can be found in include/linux/irqflags.h: do { trace_hardirqs_on(); raw_local_irq_enable(); } while (0) Without this change, we hit the following DEBUG_LOCKS_WARN_ON. [ 7.760000] ------------[ cut here ]------------ [ 7.760000] WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2711 resume_user_mode_begin+0x48/0xf0 [ 7.770000] DEBUG_LOCKS_WARN_ON(!irqs_disabled()) [ 7.780000] Modules linked in: [ 7.780000] CPU: 0 PID: 1 Comm: init Not tainted 4.7.0-00003-gc668bb9-dirty #366 [ 7.790000] [ 7.790000] Stack Trace: [ 7.790000] arc_unwind_core.constprop.1+0xa4/0x118 [ 7.800000] warn_slowpath_fmt+0x72/0x158 [ 7.800000] resume_user_mode_begin+0x48/0xf0 [ 7.810000] ---[ end trace 6f6a7a8fae20d2f0 ]--- Signed-off-by:
Daniel Mentz <danielmentz@google.com> Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> [bwh: Backported to 3.16: adjust filename] Signed-off-by:
-
Sebastian Andrzej Siewior authored
commit 5cf0791d upstream. There's a subtle preemption race on UP kernels: Usually current->mm (and therefore mm->pgd) stays the same during the lifetime of a task so it does not matter if a task gets preempted during the read and write of the CR3. But then, there is this scenario on x86-UP: TaskA is in do_exit() and exit_mm() sets current->mm = NULL followed by: -> mmput() -> exit_mmap() -> tlb_finish_mmu() -> tlb_flush_mmu() -> tlb_flush_mmu_tlbonly() -> tlb_flush() -> flush_tlb_mm_range() -> __flush_tlb_up() -> __flush_tlb() -> __native_flush_tlb() At this point current->mm is NULL but current->active_mm still points to the "old" mm. Let's preempt taskA _after_ native_read_cr3() by taskB. TaskB has its own mm so CR3 has changed. Now preempt back to taskA. TaskA has no ->mm set so it borrows taskB's mm and so CR3 remains unchanged. Once taskA gets active it continues where it was interrupted and that means it writes its old CR3 value back. Everything is fine because userland won't need its memory anymore. Now the fun part: Let's preempt taskA one more time and get back to taskB. This time switch_mm() won't do a thing because oldmm (->active_mm) is the same as mm (as per context_switch()). So we remain with a bad CR3 / PGD and return to userland. The next thing that happens is handle_mm_fault() with an address for the execution of its code in userland. handle_mm_fault() realizes that it has a PTE with proper rights so it returns doing nothing. But the CPU looks at the wrong PGD and insists that something is wrong and faults again. And again. And one more time… This pagefault circle continues until the scheduler gets tired of it and puts another task on the CPU. It gets little difficult if the task is a RT task with a high priority. The system will either freeze or it gets fixed by the software watchdog thread which usually runs at RT-max prio. But waiting for the watchdog will increase the latency of the RT task which is no good. Fix this by disabling preemption across the critical code section. Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by:
Rik van Riel <riel@redhat.com> Acked-by:
Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Borislav Petkov <bp@suse.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mel Gorman <mgorman@suse.de> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/1470404259-26290-1-git-send-email-bigeasy@linutronix.de [ Prettified the changelog. ] Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Felipe Balbi authored
commit c7de5734 upstream. When using SG lists, we would end up setting request->actual to: num_mapped_sgs * (request->length - count) Let's fix that up by incrementing request->actual only once. Reported-by:
Brian E Rogers <brian.e.rogers@intel.com> Signed-off-by:
-
Stefan Haberland authored
commit 9ba333dc upstream. When a device is in a status where CIO has killed all I/O by itself the interrupt for a clear request may not contain an irb to determine the clear function. Instead it contains an error pointer -EIO. This was ignored by the DASD int_handler leading to a hanging device waiting for a clear interrupt. Handle -EIO error pointer correctly for requests that are clear pending and treat the clear as successful. Signed-off-by:
Stefan Haberland <sth@linux.vnet.ibm.com> Reviewed-by:
Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Zefan Li authored
commit 06f4e948 upstream. A new task inherits cpus_allowed and mems_allowed masks from its parent, but if someone changes cpuset's config by writing to cpuset.cpus/cpuset.mems before this new task is inserted into the cgroup's task list, the new task won't be updated accordingly. Signed-off-by:
Zefan Li <lizefan@huawei.com> Signed-off-by:
Tejun Heo <tj@kernel.org> [bwh: Backported to 3.16: adjust context] Signed-off-by:
-
Alan Stern authored
commit aed9d65a upstream. Erroneous or malicious endpoint descriptors may have non-zero bits in reserved positions, or out-of-bounds values. This patch helps prevent these from causing problems by bounds-checking the wMaxPacketValue entries in endpoint descriptors and capping the values at the maximum allowed. This issue was first discovered and tests were conducted by Jake Lamberson <jake.lamberson1@gmail.com>, an intern working for Rosie Hall. Signed-off-by:
roswest <roswest@cisco.com> Tested-by:
-
Russell King authored
commit a0118c8b upstream. Since 6de62f15 ("crypto: algif_hash - Require setkey before accept(2)"), the AF_ALG interface requires userspace to provide a key to any algorithm that has a setkey method. However, the non-HMAC algorithms are not keyed, so setting a key is unnecessary. Fix this by removing the setkey method from the non-keyed hash algorithms. Fixes: 6de62f15 ("crypto: algif_hash - Require setkey before accept(2)") Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Mahesh Salgaonkar authored
commit c74dd88e upstream. When machine check occurs with MSR(RI=0), it means MC interrupt is unrecoverable and kernel goes down to panic path. But the console message still shows it as recovered. This patch fixes the MCE console messages. Fixes: 36df96f8 ("powerpc/book3s: Decode and save machine check event.") Signed-off-by:
Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Liping Zhang authored
commit 00a3101f upstream. Like NFQNL_MSG_VERDICT_BATCH do, we should also reject the verdict request when the portid is not same with the initial portid(maybe from another process). Fixes: 97d32cf9 ("netfilter: nfnetlink_queue: batch verdict support") Signed-off-by:
Liping Zhang <liping.zhang@spreadtrum.com> Reviewed-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> [bwh: Backported to 3.16: adjust filename] Signed-off-by:
-
Liping Zhang authored
commit b173a28f upstream. The 'name' filed in struct nf_conntrack_expect_policy{} is not a pointer, so check it is NULL or not will always return true. Even if the name is empty, slash will always be displayed like follows: # cat /proc/net/nf_conntrack_expect 297 l3proto = 2 proto=6 src=1.1.1.1 dst=2.2.2.2 sport=1 dport=1025 ftp/ ^ Fixes: 3a8fc53a ("netfilter: nf_ct_helper: allocate 16 bytes for the helper and policy names") Signed-off-by:
-
Mahesh Salgaonkar authored
commit bc14c491 upstream. The current implementation of MCE early handling modifies CR0/1 registers without saving its old values. Fix this by moving early check for powersaving mode to machine_check_handle_early(). The power architecture 2.06 or later allows the possibility of getting machine check while in nap/sleep/winkle. The last bit of HSPRG0 is set to 1, if thread is woken up from winkle. Hence, clear the last bit of HSPRG0 (r13) before MCE handler starts using it as paca pointer. Also, the current code always puts the thread into nap state irrespective of whatever idle state it woke up from. Fix that by looking at paca->thread_idle_state and put the thread back into same state where it came from. Fixes: 1c51089f ("powerpc/book3s: Return from interrupt if coming from evil context.") Reported-by:
Paul Mackerras <paulus@samba.org> Signed-off-by:
Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com> Signed-off-by:
-
Dave Carroll authored
commit fa00c437 upstream. In aacraid's ioctl_send_fib() we do two fetches from userspace, one the get the fib header's size and one for the fib itself. Later we use the size field from the second fetch to further process the fib. If for some reason the size from the second fetch is different than from the first fix, we may encounter an out-of- bounds access in aac_fib_send(). We also check the sender size to insure it is not out of bounds. This was reported in https://bugzilla.kernel.org/show_bug.cgi?id=116751 and was assigned CVE-2016-6480. Reported-by:
Pengfei Wang <wpengfeinudt@gmail.com> Fixes: 7c00ffa3 '[SCSI] 2.6 aacraid: Variable FIB size (updated patch)' Signed-off-by:
Dave Carroll <david.carroll@microsemi.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
-
Mario Kleiner authored
commit 196f954e upstream. This reverts commit 013dd9e0 ("drm/i915/dp: fall back to 18 bpp when sink capability is unknown") This commit introduced a regression into stable kernels, as it reduces output color depth to 6 bpc for any video sink connected to a Displayport connector if that sink doesn't report a specific color depth via EDID, or if our EDID parser doesn't actually recognize the proper bpc from EDID. Affected are active DisplayPort->VGA converters and active DisplayPort->DVI converters. Both should be able to handle 8 bpc, but are degraded to 6 bpc with this patch. The reverted commit was meant to fix Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=105331 A followup patch implements a fix for that specific bug, which is caused by a faulty EDID of the affected DP panel by adding a new EDID quirk for that panel. DP 18 bpp fallback handling and other improvements to DP sink bpc detection will be handled for future kernels in a separate series of patches. Please backport to stable. Signed-off-by:
Mario Kleiner <mario.kleiner.de@gmail.com> Acked-by:
Jani Nikula <jani.nikula@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Mario Kleiner authored
commit e10aec65 upstream. Bugzilla https://bugzilla.kernel.org/show_bug.cgi?id=105331 reports that the "AEO model 0" display is driven with 8 bpc without dithering by default, which looks bad because that panel is apparently a 6 bpc DP panel with faulty EDID. A fix for this was made by commit 013dd9e0 ("drm/i915/dp: fall back to 18 bpp when sink capability is unknown"). That commit triggers new regressions in precision for DP->DVI and DP->VGA displays. A patch is out to revert that commit, but it will revert video output for the AEO model 0 panel to 8 bpc without dithering. The EDID 1.3 of that panel, as decoded from the xrandr output attached to that bugzilla bug report, is somewhat faulty, and beyond other problems also sets the "DFP 1.x compliant TMDS" bit, which according to DFP spec means to drive the panel with 8 bpc and no dithering in absence of other colorimetry information. Try to make the original bug reporter happy despite the faulty EDID by adding a quirk to mark that panel as 6 bpc, so 6 bpc output with dithering creates a nice picture. Tested by injecting the edid from the fdo bug into a DP connector via drm_kms_helper.edid_firmware and verifying the 6 bpc + dithering is selected. This patch should be backported to stable. Signed-off-by:
-
Alex Williamson authored
commit c8952a70 upstream. There are multiple cases in vfio_pci_set_ctx_trigger_single() where we assume we can safely read from our data pointer without actually checking whether the user has passed any data via the count field. VFIO_IRQ_SET_DATA_NONE in particular is entirely broken since we attempt to pull an int32_t file descriptor out before even checking the data type. The other data types assume the data pointer contains one element of their type as well. In part this is good news because we were previously restricted from doing much sanitization of parameters because it was missed in the past and we didn't want to break existing users. Clearly DATA_NONE is completely broken, so it must not have any users and we can fix it up completely. For DATA_BOOL and DATA_EVENTFD, we'll just protect ourselves, returning error when count is zero since we previously would have oopsed. Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Reported-by:
Chris Thompson <the_cartographer@hotmail.com> Reviewed-by:
Eric Auger <eric.auger@redhat.com> [bwh: Backported to 3.16: - Drop changes to vfio_pci_set_req_trigger() - Apply remaining changes in vfio_pci_set_err_trigger()] Signed-off-by:
-
Alexey Klimov authored
commit 647024a7 upstream. udriver struct allocated by kzalloc() will not be freed if usb_register() and next calls fail. This patch fixes this by adding one more step with kfree(udriver) in error path. Signed-off-by:
Alexey Klimov <klimov.linux@gmail.com> Acked-by:
-
Daniele Palmas authored
commit 01d7956b upstream. This patch adds a set of compositions for Telit LE920A4. Compositions in short are: 0x1207: tty + tty 0x1208: tty + adb + tty + tty 0x1211: tty + adb + ecm 0x1212: tty + adb 0x1213: ecm + tty 0x1214: tty + adb + ecm + tty telit_le922_blacklist_usbcfg3 is reused for compositions 0x1211 and 0x1214 due to the same interfaces positions. Signed-off-by:
Daniele Palmas <dnlplm@gmail.com> Signed-off-by:
-
Sheng-Hui J. Chu authored
commit ae34d12c upstream. BCM20706V2_EVAL is a WICED dev board designed with FT2232H USB 2.0 UART/FIFO IC. To support BCM920706V2_EVAL dev board for WICED development on Linux. Add the VID(0a5c) and PID(6422) to ftdi_sio driver to allow loading ftdi_sio for this board. Signed-off-by:
Sheng-Hui J. Chu <s.jeffrey.chu@gmail.com> Signed-off-by:
-
Robert Deliën authored
commit 6977495c upstream. Ivium Technologies uses the FTDI VID with custom PIDs for their line of electrochemical interfaces and the PalmSens they developed for PalmSens BV. Signed-off-by:
Robert Delien <robert@delien.nl> Signed-off-by:
-
