The recent changes in checking for Bluetooth status added some callbacks to code
in rtlwifi. To make certain that all callbacks are defined, a dummy routine has been
added to rtlwifi, and the drivers that need to use it are modified.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

During 11n RX reordering, if there is a hole in RX table,
driver will not send packets to kernel until the rxreorder
timer expires or the table is full.
However, currently driver always restarts rxreorder timer when
receiving a packet, which causes the timer hardly to expire.
So while connected with to 11n AP in a busy environment,
ping packets may get blocked for about 30 seconds.

This patch fixes this timer restarting by ensuring rxreorder timer
would only be restarted either timer is not set or start_win
has changed.
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Plus Chen <pchen@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The right shift operation has higher precedence than the mask so we
left shift by "(i * 3)" and then immediately right shift by "(i * 3)"
then we mask.  It should be left shift, mask, and then right shift.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

0x1b75 0xa200 AirLive WN-200USB wireless 11b/g/n dongle

References: https://bugs.debian.org/766802Reported-by: Martin Mokrejs <mmokrejs@fold.natur.cuni.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Cyril Brulebois <kibi@debian.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge tag 'mac80211-for-john-2014-10-23' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg <johannes@sipsolutions.net> says:

"Here are a few fixes for the wireless stack: one fixes the
RTS rate, one for a debugfs file, one to return the correct
channel to userspace, a sanity check for a userspace value
and the remaining two are just documentation fixes."
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge tag 'iwlwifi-for-john-2014-10-23' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes

Emmanuel Grumbach <egrumbach@gmail.com> says:

"I revert here a patch that caused interoperability issues.
dvm gets a fix for a bug that was reported by many users.
Two minor fixes for BT Coex and platform power fix that helps
reducing latency when the PCIe link goes to low power states."
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl_poll_bit may return a strictly positive value when the
poll doesn't match on the first try.
This was caught when WoWLAN started failing upon resume
even if the poll_bit actually succeeded.

Also change a wrong print. If we reach the end of
iwl_pcie_prepare_card_hw, it means that we couldn't
get the devices.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This reverts commit aa11bbf3.
This commit was causing connection issues and is not needed
if IWL_MVM_RS_RSSI_BASED_INIT_RATE is set to false by default.

Regardless of the issues mentioned above, this patch added the
following WARNING:

WARNING: CPU: 0 PID: 3946 at drivers/net/wireless/iwlwifi/mvm/tx.c:190 iwl_mvm_set_tx_params+0x60a/0x6f0 [iwlmvm]()
Got an HT rate for a non data frame 0x8
CPU: 0 PID: 3946 Comm: wpa_supplicant Tainted: G           O   3.17.0+ #6
Hardware name: LENOVO 20ANCTO1WW/20ANCTO1WW, BIOS GLET71WW (2.25 ) 07/02/2014
 0000000000000009 ffffffff814fa911 ffff8804288db8f8 ffffffff81064f52
 0000000000001808 ffff8804288db948 ffff88040add8660 ffff8804291b5600
 0000000000000000 ffffffff81064fb7 ffffffffa07b73d0 0000000000000020
Call Trace:
 [<ffffffff814fa911>] ? dump_stack+0x41/0x51
 [<ffffffff81064f52>] ? warn_slowpath_common+0x72/0x90
 [<ffffffff81064fb7>] ? warn_slowpath_fmt+0x47/0x50
 [<ffffffffa07a39ea>] ? iwl_mvm_set_tx_params+0x60a/0x6f0 [iwlmvm]
 [<ffffffffa07a3cf8>] ? iwl_mvm_tx_skb+0x48/0x3c0 [iwlmvm]
 [<ffffffffa079cb9b>] ? iwl_mvm_mac_tx+0x7b/0x180 [iwlmvm]
 [<ffffffffa0746ce9>] ? __ieee80211_tx+0x2b9/0x3c0 [mac80211]
 [<ffffffffa07492f3>] ? ieee80211_tx+0xb3/0x100 [mac80211]
 [<ffffffffa0749c49>] ? ieee80211_subif_start_xmit+0x459/0xca0 [mac80211]
 [<ffffffff814116e7>] ? dev_hard_start_xmit+0x337/0x5f0
 [<ffffffff81430d46>] ? sch_direct_xmit+0x96/0x1f0
 [<ffffffff81411ba3>] ? __dev_queue_xmit+0x203/0x4f0
 [<ffffffff8142f670>] ? ether_setup+0x70/0x70
 [<ffffffff814e96a1>] ? packet_sendmsg+0xf81/0x1110
 [<ffffffff8140625c>] ? skb_free_datagram+0xc/0x40
 [<ffffffff813f7538>] ? sock_sendmsg+0x88/0xc0
 [<ffffffff813f7274>] ? move_addr_to_kernel.part.20+0x14/0x60
 [<ffffffff811c47c2>] ? __inode_wait_for_writeback+0x62/0xb0
 [<ffffffff813f7a91>] ? SYSC_sendto+0xf1/0x180
 [<ffffffff813f88f9>] ? __sys_recvmsg+0x39/0x70
 [<ffffffff8150066d>] ? system_call_fastpath+0x1a/0x1f
---[ end trace cc19a150d311fc63 ]---

which was reported here: https://bugzilla.kernel.org/show_bug.cgi?id=85691

CC: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When mac80211 wants to ensure that a frame is sent, it calls
the flush() callback. Until now, iwldvm implemented this by
waiting that all the frames are sent (ACKed or timeout).
In case of weak signal, this can take a significant amount
of time, delaying the next connection (in case of roaming).
Many users have reported that the flush would take too long
leading to the following error messages to be printed:

iwlwifi 0000:03:00.0: fail to flush all tx fifo queues Q 2
iwlwifi 0000:03:00.0: Current SW read_ptr 161 write_ptr 201
iwl data: 00000000: 00 00 00 00 00 00 00 00 fe ff 01 00 00 00 00 00
[snip]
iwlwifi 0000:03:00.0: FH TRBs(0) = 0x00000000
[snip]
iwlwifi 0000:03:00.0: Q 0 is active and mapped to fifo 3 ra_tid 0x0000 [9,9]
[snip]

Instead of waiting for these packets, simply drop them. This
significantly improves the responsiveness of the network.
Note that all the queues are flushed, but the VO one. This
is not typically used by the applications and it likely
contains management frames that are useful for connection
or roaming.

This bug is tracked here:
https://bugzilla.kernel.org/show_bug.cgi?id=56581

But it is duplicated in distributions' trackers.
A simple search in Ubuntu's database led to these bugs:

https://bugs.launchpad.net/ubuntu/+source/linux-firmware/+bug/1270808
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1305406
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1356236
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1360597
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1361809

Cc: <stable@vger.kernel.org>
Depends-on: 77be2c54 ("mac80211: add vif to flush call")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Don't add the time event to the list. We added it several
times the same time event, which leads to an infinite loop
when walking the list.

Since we (currently) don't support more than one ROC for STA
vif at a time, enforce this and don't add the time event
to any list.

We were also missing the locking of the mutex which led to
a lockdep splat - fix that.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The tx power should be limited from many reasons.
currently, setting the tx power is available by the mvm only for
station interface. Adding the tx power condition to
bss_info_changed_ap_ibss make it available also for AP.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The probe requests sent during scan must get BT prio 3.
Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Cc: <stable@vger.kernel.org> [3.16+]
Fixes: 2adc8949 ("iwlwifi: mvm: BT Coex - fix boost register / LUT values")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

I changed the string but forgot to update the fix also to
MODULE_FIRMWARE().
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The LTR is the handshake between the device and the root
complex about the latency allowed when the bus exits power
save. This configuration was missing and this led to high
latency in the link power up. The end user could experience
high latency in the network because of this.

Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Drivers that do not use the get_btc_status() callback may not define a
dummy routine. The caller needs to check before making the call.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Thadeu Cascardo <cascardo@cascardo.eti.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In some cases the limit may be the same as reg->power_limit, but the
actual value that the hardware uses is not up to date. In that case, a
wrong value for current tx power is tracked internally.
Fix this by unconditionally updating it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl92c_set_fw_rsvdpagepkt is used by rtl8192cu and its pci sibling rtl8192ce.
rtl_cmd_send_packet crashes when called inside rtl8192cu because it works on
memory allocated only by rtl8192ce.
Fix the crash by calling a dummy function when used in rtl8192cu.
Comparision with the realtek vendor driver makes me think, something is missing in
the dummy function.
Short test as WPA2 station show good results connected to an 802.11g basestation.
Traffic stops after few MBytes as WPA2 station connected to an 802.11n basestation.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In a previous patch the call to ieee80211_register_hw was moved from the
load firmware callback to the rtl_pci_probe only.
rt8192cu also uses this callback. Currently it doesnt create a wlan%d device.
Fill in the call to ieee80211_register_hw in rtl_usb_probe.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Initialize function pointer with a function indicating bt coexist is not there.
Prevents Ooops.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Many AP devices do not have the proper regulatory domain programmed in
EEPROM. Instead they expect the software to set the appropriate region.
For these devices, the country code defaults to US, and the driver uses
the US CTL tables as well.
On devices bought in Europe this can lead to tx power being set too high
on the band edges, even if the cfg80211 regdomain is set correctly.
Fix this issue by taking into account the DFS region, but only when the
EEPROM regdomain is set to default.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The kbuild test robot reported a possible array overrun. The affected code
checks for overruns, but fails to take the steps necessary to fix them.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Enabling HW queue control for normal (non-mcc) mode
causes problems with queue management, resulting
in traffic stall. Since it is mainly required for
fairness in MCC mode, disable it for the general case.

Bug: https://dev.openwrt.org/ticket/18164

Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use "%s" in the workqueue allocation to make sure the rtl_hal_cfg name
can never accidentally leak information via a format string.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It was found attached to the BCM47081A0 SoC. Log:
bcma: bus0: Found chip with id 43228, rev 0x00 and package 0x08
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
And changed from using strncat to strlcat to simplify code.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The driver logs a message when the default branch of switch statements are
taken. Such information is useful when debugging, but these log items should
not be seen for standard usage.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit 2101e533 ("bcma: register bcma as device tree driver")
introduces a hard dependency on OF_ADDRESS into the bcma driver.
OF_ADDRESS is specifically disabled for the sparc architecture.
This results in the following error when building sparc64:allmodconfig.

drivers/bcma/main.c: In function 'bcma_of_find_child_device':
drivers/bcma/main.c:150:3: error: implicit declaration of function 'of_translate_address'

Fixes: 2101e533 ("bcma: register bcma as device tree driver")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ATM an HT rc_stats line is 106 chars.
Times 8(MCS_GROUP_RATES)*3(SS)*2(GI)*2(BW) + CCK(4), i.e. x100, this is
well above the current 8192 - sizeof(*ms) currently allocated.

Fix this by squeezing the output as follows (not that we're short on
memory but this also improves readability and range, the new format adds
one more digit to *ok/*cum and ok/cum):

- Before (HT) (106 ch):
type           rate     throughput  ewma prob   this prob  retry   this succ/attempt   success    attempts
CCK/LP          5.5M           0.0        0.0         0.0      0              0(  0)         0           0
HT20/LGI ABCDP MCS0            0.0        0.0         0.0      1              0(  0)         0           0
- After (75 ch):
type           rate     tpt eprob *prob ret  *ok(*cum)        ok(      cum)
CCK/LP          5.5M    0.0   0.0   0.0   0    0(   0)         0(        0)
HT20/LGI ABCDP MCS0     0.0   0.0   0.0   1    0(   0)         0(        0)

- Align non-HT format Before (non-HT) (83 ch):
rate      throughput  ewma prob  this prob  this succ/attempt   success    attempts
ABCDP  6         0.0        0.0        0.0             0(  0)         0           0
      54         0.0        0.0        0.0             0(  0)         0           0
- After (61 ch):
rate          tpt eprob *prob  *ok(*cum)        ok(      cum)
ABCDP  1      0.0   0.0   0.0    0(   0)         0(        0)
      54      0.0   0.0   0.0    0(   0)         0(        0)

*This also adds dynamic checks for overflow, lowers the size of the
non-HT request (allowing > 30 entries) and replaces the buddy-rounded
allocations (s/sizeof(*ms) + 8192/8192).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Pull ntb (non-transparent bridge) updates from Jon Mason:
 "Add support for Haswell NTB split BARs, a debugfs entry for basic
  debugging info, and some code clean-ups"

* tag 'ntb-3.18' of git://github.com/jonmason/ntb:
  ntb: Adding split BAR support for Haswell platforms
  ntb: use errata flag set via DID to implement workaround
  ntb: conslidate reading of PPD to move platform detection earlier
  ntb: move platform detection to separate function
  NTB: debugfs device entry

Pull i2c updates from Wolfram Sang:
 "Highlights from the I2C subsystem for 3.18:

   - new drivers for Axxia AM55xx, and Hisilicon hix5hd2 SoC.

   - designware driver gained AMD support, exynos gained exynos7 support

  The rest is usual driver stuff.  Hopefully no lowlights this time"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: i801: Add Device IDs for Intel Sunrise Point PCH
  i2c: hix5hd2: add i2c controller driver
  i2c-imx: Disable the clock on probe failure
  i2c: designware: Add support for AMD I2C controller
  i2c: designware: Rework probe() to get clock a bit later
  i2c: designware: Default to fast mode in case of ACPI
  i2c: axxia: Add I2C driver for AXM55xx
  i2c: exynos: add support for HSI2C module on Exynos7
  i2c: mxs: detect No Slave Ack on SELECT in PIO mode
  i2c: cros_ec: Remove EC_I2C_FLAG_10BIT
  i2c: cros-ec-tunnel: Add of match table
  i2c: rcar: remove sign-compare flaw
  i2c: ismt: Use minimum descriptor size
  i2c: imx: Add arbitration lost check
  i2c: rk3x: Remove unlikely() annotations
  i2c: rcar: check for no IRQ in rcar_i2c_irq()
  i2c: rcar: make rcar_i2c_prepare_msg() *void*
  i2c: rcar: simplify check for last message
  i2c: designware: add support of platform data to set I2C mode
  i2c: designware: add support of I2C standard mode

Pull sound fixes from Takashi Iwai:
 "Here are a collection of small fixes after 3.18 merge.

  The urgent one is the fix for kernel panics with linked PCM substream
  triggered by the recent nonatomic PCM ops support.  Other two fixes
  (emu10k1 and bebob) are stable fixes, and one easy PCI ID addition for
  a new Intel HD-audio controller"

* tag 'sound-fix-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda_intel: Add Device IDs for Intel Sunrise Point PCH
  ALSA: emu10k1: Fix deadlock in synth voice lookup
  ALSA: pcm: Fix referred substream in snd_pcm_action_group() unlock loop
  ALSA: bebob: Fix failure to detect source of clock for Terratec Phase 88

Pull second round of input updates from Dmitry Torokhov:
 "Mostly simple bug fixes, although we do have one brand new driver for
  Microchip AR1021 i2c touchscreen.

  Also there is the change to stop trying to use i8042 active
  multiplexing by default (it is still possible to activate it via
  i8042.nomux=0 on boxes that implement it)"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: xpad - add Thrustmaster as Xbox 360 controller vendor
  Input: xpad - add USB ID for Thrustmaster Ferrari 458 Racing Wheel
  Input: max77693-haptic - fix state check in imax77693_haptic_disable()
  Input: xen-kbdfront - free grant table entry in xenkbd_disconnect_backend
  Input: alps - fix v4 button press recognition
  Input: i8042 - disable active multiplexing by default
  Input: i8042 - add noloop quirk for Asus X750LN
  Input: synaptics - gate forcepad support by DMI check
  Input: Add Microchip AR1021 i2c touchscreen
  Input: cros_ec_keyb - add of match table
  Input: serio - avoid negative serio device numbers
  Input: avoid negative input device numbers
  Input: automatically set EV_ABS bit in input_set_abs_params
  Input: adp5588-keys - cancel workqueue in failure path
  Input: opencores-kbd - switch to using managed resources
  Input: evdev - fix EVIOCG{type} ioctl

Pull infiniband/RDMA updates from Roland Dreier:
 - large set of iSER initiator improvements
 - hardware driver fixes for cxgb4, mlx5 and ocrdma
 - small fixes to core midlayer

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (47 commits)
  RDMA/cxgb4: Fix ntuple calculation for ipv6 and remove duplicate line
  RDMA/cxgb4: Add missing neigh_release in find_route
  RDMA/cxgb4: Take IPv6 into account for best_mtu and set_emss
  RDMA/cxgb4: Make c4iw_wr_log_size_order static
  IB/core: Fix XRC race condition in ib_uverbs_open_qp
  IB/core: Clear AH attr variable to prevent garbage data
  RDMA/ocrdma: Save the bit environment, spare unncessary parenthesis
  RDMA/ocrdma: The kernel has a perfectly good BIT() macro - use it
  RDMA/ocrdma: Don't memset() buffers we just allocated with kzalloc()
  RDMA/ocrdma: Remove a unused-label warning
  RDMA/ocrdma: Convert kernel VA to PA for mmap in user
  RDMA/ocrdma: Get vlan tag from ib_qp_attrs
  RDMA/ocrdma: Add default GID at index 0
  IB/mlx5, iser, isert: Add Signature API additions
  Target/iser: Centralize ib_sig_domain setting
  IB/iser: Centralize ib_sig_domain settings
  IB/mlx5: Use extended internal signature layout
  IB/iser: Set IP_CSUM as default guard type
  IB/iser: Remove redundant assignment
  IB/mlx5: Use enumerations for PI copy mask
  ...

Pull more perf updates from Ingo Molnar:
 "A second (and last) round of late coming fixes and changes, almost all
  of them in perf tooling:

  User visible tooling changes:

   - Add period data column and make it default in 'perf script' (Jiri
     Olsa)

   - Add a visual cue for toggle zeroing of samples in 'perf top'
     (Taeung Song)

   - Improve callchains when using libunwind (Namhyung Kim)

  Tooling fixes and infrastructure changes:

   - Fix for double free in 'perf stat' when using some specific invalid
     command line combo (Yasser Shalabi)

   - Fix off-by-one bugs in map->end handling (Stephane Eranian)

   - Fix off-by-one bug in maps__find(), also related to map->end
     handling (Namhyung Kim)

   - Make struct symbol->end be the first addr after the symbol range,
     to make it match the convention used for struct map->end.  (Arnaldo
     Carvalho de Melo)

   - Fix perf_evlist__add_pollfd() error handling in 'perf kvm stat
     live' (Jiri Olsa)

   - Fix python test build by moving callchain_param to an object linked
     into the python binding (Jiri Olsa)

   - Document sysfs events/ interfaces (Cody P Schafer)

   - Fix typos in perf/Documentation (Masanari Iida)

   - Add missing 'struct option' forward declaration (Arnaldo Carvalho
     de Melo)

   - Add option to copy events when queuing for sorting across cpu
     buffers and enable it for 'perf kvm stat live', to avoid having
     events left in the queue pointing to the ring buffer be rewritten
     in high volume sessions.  (Alexander Yarygin, improving work done
     by David Ahern):

   - Do not include a struct hists per perf_evsel, untangling the
     histogram code from perf_evsel, to pave the way for exporting a
     minimalistic tools/lib/api/perf/ library usable by tools/perf and
     initially by the rasd daemon being developed by Borislav Petkov,
     Robert Richter and Jean Pihet.  (Arnaldo Carvalho de Melo)

   - Make perf_evlist__open(evlist, NULL, NULL), i.e. without cpu and
     thread maps mean syswide monitoring, reducing the boilerplate for
     tools that only want system wide mode.  (Arnaldo Carvalho de Melo)

   - Move exit stuff from perf_evsel__delete to perf_evsel__exit, delete
     should be just a front end for exit + free (Arnaldo Carvalho de
     Melo)

   - Add support to new style format of kernel PMU event.  (Kan Liang)

  and other misc fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (45 commits)
  perf script: Add period as a default output column
  perf script: Add period data column
  perf evsel: No need to drag util/cgroup.h
  perf evlist: Add missing 'struct option' forward declaration
  perf evsel: Move exit stuff from __delete to __exit
  kprobes/x86: Remove stale ARCH_SUPPORTS_KPROBES_ON_FTRACE define
  perf kvm stat live: Enable events copying
  perf session: Add option to copy events when queueing
  perf Documentation: Fix typos in perf/Documentation
  perf trace: Use thread_{,_set}_priv helpers
  perf kvm: Use thread_{,_set}_priv helpers
  perf callchain: Create an address space per thread
  perf report: Set callchain_param.record_mode for future use
  perf evlist: Fix for double free in tools/perf stat
  perf test: Add test case for pmu event new style format
  perf tools: Add support to new style format of kernel PMU event
  perf tools: Parse the pmu event prefix and suffix
  Revert "perf tools: Default to cpu// for events v5"
  perf Documentation: Remove Ruplicated docs for powerpc cpu specific events
  perf Documentation: sysfs events/ interfaces
  ...

Pull sparc fixes from David Miller:
 "Here we have two bug fixes:

  1) The current thread's fault_code is not setup properly upon entry to
     do_sparc64_fault() in some paths, leading to spurious SIGBUS.

  2) Don't use a zero length array at the end of thread_info on sparc64,
     otherwise end_of_stack() isn't right"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Do not define thread fpregs save area as zero-length array.
  sparc64: Fix corrupted thread fault code.

Pull networking fixes from David Miller:
 "A quick batch of bug fixes:

  1) Fix build with IPV6 disabled, from Eric Dumazet.

  2) Several more cases of caching SKB data pointers across calls to
     pskb_may_pull(), thus referencing potentially free'd memory.  From
     Li RongQing.

  3) DSA phy code tests operation presence improperly, instead of going:

        if (x->ops->foo)
                r = x->ops->foo(args);

     it was going:

        if (x->ops->foo(args))
                r = x->ops->foo(args);

   Fix from Andew Lunn"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  Net: DSA: Fix checking for get_phy_flags function
  ipv6: fix a potential use after free in sit.c
  ipv6: fix a potential use after free in ip6_offload.c
  ipv4: fix a potential use after free in gre_offload.c
  tcp: fix build error if IPv6 is not enabled

The check for the presence or not of the optional switch function
get_phy_flags() called the function, rather than checked to see if it
is a NULL pointer. This causes a derefernce of a NULL pointer on all
switch chips except the sf2, the only switch to implement this call.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 6819563e ("net: dsa: allow switch drivers to specify phy_device::dev_flags")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This breaks the stack end corruption detection facility.

What that facility does it write a magic value to "end_of_stack()"
and checking to see if it gets overwritten.

"end_of_stack()" is "task_thread_info(p) + 1", which for sparc64 is
the beginning of the FPU register save area.

So once the user uses the FPU, the magic value is overwritten and the
debug checks trigger.

Fix this by making the size explicit.

Due to the size we use for the fpsaved[], gsr[], and xfsr[] arrays we
are limited to 7 levels of FPU state saves.  So each FPU register set
is 256 bytes, allocate 256 * 7 for the fpregs area.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>

Every path that ends up at do_sparc64_fault() must install a valid
FAULT_CODE_* bitmask in the per-thread fault code byte.

Two paths leading to the label winfix_trampoline (which expects the
FAULT_CODE_* mask in register %g4) were not doing so:

1) For pre-hypervisor TLB protection violation traps, if we took
   the 'winfix_trampoline' path we wouldn't have %g4 initialized
   with the FAULT_CODE_* value yet.  Resulting in using the
   TLB_TAG_ACCESS register address value instead.

2) In the TSB miss path, when we notice that we are going to use a
   hugepage mapping, but we haven't allocated the hugepage TSB yet, we
   still have to take the window fixup case into consideration and
   in that particular path we leave %g4 not setup properly.

Errors on this sort were largely invisible previously, but after
commit 4ccb9272 ("sparc64: sun4v TLB
error power off events") we now have a fault_code mask bit
(FAULT_CODE_BAD_RA) that triggers due to this bug.

FAULT_CODE_BAD_RA triggers because this bit is set in TLB_TAG_ACCESS
(see #1 above) and thus we get seemingly random bus errors triggered
for user processes.

Fixes: 4ccb9272 ("sparc64: sun4v TLB error power off events")
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>