V3 of basic KZM9D board support. At this point a quite
thin layer that makes use of the Emma Mobile EV2 SoC code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

This is V3 of the Emma Mobile EV2 SoC support.
Included here is support for serial and timer
devices which is just about enough to boot a kernel.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

This patch is V2 of the Emma Mobile GPIO driver. This
driver is designed to be reusable between multiple SoCs
that share the same basic building block, but so far it
has only been used on Emma Mobile EV2.

Each driver instance handles 32 GPIOs with individually
maskable IRQs. The driver operates on two I/O memory
ranges and the 32 GPIOs are hooked up to two interrupts.

In the case of Emma Mobile EV2 this GPIO building block
is used as main external interrupt controller hooking up
159 GPIOS as 159 interrupts via 5 driver instances and
10 interrupts to the GIC and the Cortex-A9 Dual.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Current IRQ16-IRQ31 irq number are located around 800 from
1ee8299a
(ARM: mach-shmobile: Use 0x3400 as INTCS vector offset)

But, the PINT0/1 IRQ number are also located around 800 from
0df1a838
(ARM: mach-shmobile: sh73a0 PINT IRQ base fix)

This patch relocates PINT0/1 IRQ number to around 700 where is not used,
and adds current IRQ location table in comment area.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

If the clocks is always same value as the parent clock,
we can use followparent_recalc() for .recalc
Reported-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

R8A7740 USB needs many clocks for workaround,
and it has confusing name "usb24s" and "usb24".
This "usb24s" will be used by other clocks.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Current workaround of I2C on r8a7740 used mdelay(),
but it was an overkill.
This patch cleans up the workaround delay.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Update the mach-shmobile shared delay calibration code for late
timers. All existing in-tree non-DT socs are however using early
timers today and they are unaffected by this change.

The patch modifies shmobile_setup_delay() from using lpj_fine
to preset_lpj. This change allows us to preset the worst case
loops-per-jiffy value to all CPU cores on the system.

The old code which made use of lpj_fine did not affect the
secondary CPU cores which made it impossible to boot on SMP
without early timers.

Needed for SMP SoCs using late timers like EMEV2 or any other
mach-shmobile SMP SoC that makes use of late timers via DT.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

* renesas-dt:
  ARM: mach-shmobile: sh7372 generic board support via DT V2
  ARM: mach-shmobile: Rework sh7372 INTCS demuxer V2
  ARM: mach-shmobile: Use INTC_IRQ_PINS_16H on sh7372
  ARM: mach-shmobile: Use 0x3400 as INTCS vector offset
  ARM: mach-shmobile: Introduce INTC_IRQ_PINS_16H
  ARM: mach-shmobile: Introduce shmobile_setup_delay()

Make sure L1 caches are invalidated when booting secondary
cores. Needed to boot all mach-shmobile SMP systems that
are using Cortex-A9 including sh73a0, r8a7779 and EMEV2.

Thanks to imx and tegra guys for actual code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Fix SMP TWD boot regression on sh73a0 based platforms caused by:

4200b16d ARM: shmobile: convert to twd_local_timer_register() interface

After the merge of the above commit it has been impossible to boot
sh73a0 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.

This patch fixes the regression on sh73a0 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.

This patch removed shmobile_twd_init() which is no longer needed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Fix SMP TWD boot regression on r8a7779 based platforms caused by:

4200b16d ARM: shmobile: convert to twd_local_timer_register() interface

After the merge of the above commit it has been impossible to boot
r8a7779 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.

This patch fixes the regression on r8a7779 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

This also fixes the following modular mmc build failure:

arch/arm/mach-shmobile/built-in.o: In function `mackerel_sdhi0_gpio_cd':
pfc-sh7372.c:(.text+0x1138): undefined reference to `mmc_detect_change'

on this platform by eliminating the use of an inline function, which
calls into the mmc core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

This also fixes the following modular mmc build failure:

arch/arm/mach-shmobile/built-in.o: In function `ag5evm_sdhi0_gpio_cd':
pfc-sh73a0.c:(.text+0x7c0): undefined reference to `mmc_detect_change'

on this platform by eliminating the use of an inline function, which
calls into the mmc core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Pull x86 fixes form Peter Anvin

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  intel_mid_powerbtn: mark irq as IRQF_NO_SUSPEND
  arch/x86/platform/geode/net5501.c: change active_low to 0 for LED driver
  x86, relocs: Remove an unused variable
  asm-generic: Use __BITS_PER_LONG in statfs.h
  x86/amd: Re-enable CPU topology extensions in case BIOS has disabled it

Pull btrfs fixes from Chris Mason:
 "The big ones here are a memory leak we introduced in rc1, and a
  scheduling while atomic if the transid on disk doesn't match the
  transid we expected.  This happens for corrupt blocks, or out of date
  disks.

  It also fixes up the ioctl definition for our ioctl to resolve logical
  inode numbers.  The __u32 was a merging error and doesn't match what
  we ship in the progs."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: avoid sleeping in verify_parent_transid while atomic
  Btrfs: fix crash in scrub repair code when device is missing
  btrfs: Fix mismatching struct members in ioctl.h
  Btrfs: fix page leak when allocing extent buffers
  Btrfs: Add properly locking around add_root_to_dirty_list

Setting TIF_IA32 in load_aout_binary() used to be enough; these days
TASK_SIZE is controlled by TIF_ADDR32 and that one doesn't get set
there.  Switch to use of set_personality_ia32()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

verify_parent_transid needs to lock the extent range to make
sure no IO is underway, and so it can safely clear the
uptodate bits if our checks fail.

But, a few callers are using it with spinlocks held.  Most
of the time, the generation numbers are going to match, and
we don't want to switch to a blocking lock just for the error
case.  This adds an atomic flag to verify_parent_transid,
and changes it to return EAGAIN if it needs to block to
properly verifiy things.
Signed-off-by: Chris Mason <chris.mason@oracle.com>

Pull alpha fixes from Matt Turner:
 "My alpha tree is back up (after taking quite some time to get my GPG
  key signed).  It contains just some simple fixes."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
  alpha: silence 'const' warning in sys_marvel.c
  alpha: include module.h to fix modpost on Tsunami
  alpha: properly define get/set_rtc_time on Marvel/SMP
  alpha: VGA_HOSE depends on VGA_CONSOLE

The test in pdc_console_tty_close '!tty->count' was always wrong
because tty->count is decremented after tty->ops->close is called and
thus can never be zero. Hence the 'then' branch was never executed and
the timer never deleted.

This did not matter until commit 5dd5bc40 ("TTY: pdc_cons, use
tty_port").  There we needed to set TTY in tty_port to NULL, but this
never happened due to the bug above.

So change the test to really trigger at the last close by changing the
condition to 'tty->count == 1'.

Well, the driver should not touch tty->count at all.  It should use
tty_port->count and count open count there itself.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-and-tested-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull sound sound fixes from Takashi Iwai:
 "As good as nothing exciting here; just a few trivial fixes for various
  ASoC stuff."

* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ASoC: omap-pcm: Free dma buffers in case of error.
  ASoC: s3c2412-i2s: Fix dai registration
  ASoC: wm8350: Don't use locally allocated codec struct
  ASoC: tlv312aic23: unbreak resume
  ASoC: bf5xx-ssm2602: Set DAI format
  ASoC: core: check of_property_count_strings failure
  ASoC: dt: sgtl5000.txt: Add description for 'reg' field
  ASoC: wm_hubs: Make sure we don't disable differential line outputs

Pull an ACPI patch from Len Brown:
 "It fixes a D3 issue new in 3.4-rc1."

By Lin Ming via Len Brown:
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  ACPI: Fix D3hot v D3cold confusion

Currently, we'll try mounting any device who's major device number is
UNNAMED_MAJOR as NFS root.  This would happen for non-NFS devices as
well (such as 9p devices) but it wouldn't cause any issues since
mounting the device as NFS would fail quickly and the code proceeded to
doing the proper mount:

       [  101.522716] VFS: Unable to mount root fs via NFS, trying floppy.
       [  101.534499] VFS: Mounted root (9p filesystem) on device 0:18.

Commit 6829a048102a ("NFS: Retry mounting NFSROOT") introduced retries
when mounting NFS root, which means that now we don't immediately fail
and instead it takes an additional 90+ seconds until we stop retrying,
which has revealed the issue this patch fixes.

This meant that it would take an additional 90 seconds to boot when
we're not using a device type which gets detected in order before NFS.

This patch modifies the NFS type check to require device type to be
'Root_NFS' instead of requiring the device to have an UNNAMED_MAJOR
major.  This makes boot process cleaner since we now won't go through
the NFS mounting code at all when the device isn't an NFS root
("/dev/nfs").
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ASoC: Updates for 3.4

Nothing terribly exciting here, a bunch of small and simple fixes
scattered around the place.

Before this patch, ACPI_STATE_D3 incorrectly referenced D3hot
in some places, but D3cold in other places.

After this patch, ACPI_STATE_D3 always means ACPI_STATE_D3_COLD;
and all references to D3hot use ACPI_STATE_D3_HOT.

ACPI's _PR3 method is used to enter both D3hot and D3cold states.
What distinguishes D3hot from D3cold is the presence _PR3
(Power Resources for D3hot)  If these resources are all ON,
then the state is D3hot.  If _PR3 is not present,
or all _PR0 resources for the devices are OFF,
then the state is D3cold.

This patch applies after Linux-3.4-rc1.
A future syntax cleanup may remove ACPI_STATE_D3
to emphasize that it always means ACPI_STATE_D3_COLD.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Commit ec81aecb ("hfs: fix a potential buffer overflow") fixed a few
potential buffer overflows in the hfs filesystem.  But as Timo Warns
pointed out, these changes also need to be made on the hfsplus
filesystem as well.
Reported-by: Timo Warns <warns@pre-sense.de>
Acked-by: WANG Cong <amwang@redhat.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Miklos Szeredi <mszeredi@suse.cz>
Cc: Sage Weil <sage@newdream.net>
Cc: Eugene Teo <eteo@redhat.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Dave Anderson <anderson@redhat.com>
Cc: stable <stable@vger.kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer fix from Thomas Gleixner.

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  rtc: Fix possible null pointer dereference in rtc-mpc5121.c

Pull CIFS fixes from Steve French.

* git://git.samba.org/sfrench/cifs-2.6:
  fs/cifs: fix parsing of dfs referrals
  cifs: make sure we ignore the credentials= and cred= options
  [CIFS] Update cifs version to 1.78
  cifs - check S_AUTOMOUNT in revalidate
  cifs: add missing initialization of server->req_lock
  cifs: don't cap ra_pages at the same level as default_backing_dev_info
  CIFS: Fix indentation in cifs_show_options

Remove myself as cpufreq maintainer.
x86 driver changes can go through the regular x86/ACPI trees.
ARM driver changes through the ARM trees.
cpufreq core changes are rare these days, and can just go to lkml/direct.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The normal read_seqcount_begin() function will wait for any current
writers to exit their critical region by looping until the sequence
count is even.

That "wait for sequence count to stabilize" is the right thing to do if
the read-locker will just retry the whole operation on contention: no
point in doing a potentially expensive reader sequence if we know at the
beginning that we'll just end up re-doing it all.

HOWEVER.  Some users don't actually retry the operation, but instead
will abort and do the operation with proper locking.  So the sequence
count case may be the optimistic quick case, but in the presense of
writers you may want to do full locking in order to guarantee forward
progress.  The prime example of this would be the RCU name lookup.

And in that case, you may well be better off without the "retry early",
and are in a rush to instead get to the failure handling.  Thus this
"raw" interface that just returns the sequence number without testing it
- it just forces the low bit to zero so that read_seqcount_retry() will
always fail such a "active concurrent writer" scenario.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We really need to use a ACCESS_ONCE() on the sequence value read in
__read_seqcount_begin(), because otherwise the compiler might end up
reloading the value in between the test and the return of it.  As a
result, it might end up returning an odd value (which means that a write
is in progress).

If the reader is then fast enough that that odd value is still the
current one when the read_seqcount_retry() is done, we might end up with
a "successful" read sequence, even despite the concurrent write being
active.

In practice this probably never really happens - there just isn't
anything else going on around the read of the sequence count, and the
common case is that we end up having a read barrier immediately
afterwards.

So the code sequence in which gcc might decide to reaload from memory is
small, and there's no reason to believe it would ever actually do the
reload.  But if the compiler ever were to decide to do so, it would be
incredibly annoying to debug.  Let's just make sure.

Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

So that the power button still wakes up the platform.
Signed-off-by: Pierre Tardy <pierre.tardy@intel.com>
Link: http://lkml.kernel.org/r/20120504210244.F2EA5A018B@akpm.mtv.corp.google.comTested-by: Kangkai Yin <kangkai.yin@intel.com>
Tested-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>