ISAPnP support has been stable with the new pnp layer for a while.
This patch removes the experimental dependency.

This patch allows the serial driver to bind to three additional modems.

isapnp_cfg_begin and isapnp_cfg_end are exported symbols, so if any
module using them is loaded isapnp.o can't be unloaded anyway

// Linux 2.6.4-rc2
// These 2 functions shouldn't be __init for general PNP use

This patch fixes a bug in the resource configuration function.  If
there are more than one memory ranges, the isapnp driver will write
into the incorrect configuration register.

Some isapnp devices were not getting detected as a result of a bug in the isapnp
driver.  It was not following the specifications and calculating a checksum when
it was not reliable.  This problem was originally discovered by Paul L. Rogers
<rogerspl@datasync.com>.  He made an initial patch.  This release has some small
modifications, including a check to see if we run out of CSNs.

This patch updates the parport_pc driver's probing code to better
detect PnP devices.  It also removes an extra MODULE_AUTHOR.

This patch simplifies the ranged resource checking logic.

into ppc970.osdl.org:/home/torvalds/v2.6/linux

into ppc970.osdl.org:/home/torvalds/v2.6/linux

into kernel.bkbits.net:/home/davem/net-2.6

into ppc970.osdl.org:/home/torvalds/v2.6/linux

into ppc970.osdl.org:/home/torvalds/v2.6/linux

This rolls up Marc Zyngier's EISA correction (first two) and adds a missed
netdev_priv() conversion that was causing an oops on module removal.

Noticed by Jan Glauber, confirmed by Stephen Hemminger.

into ppc970.osdl.org:/home/torvalds/v2.6/linux

into kroah.com:/home/greg/linux/BK/pci-2.6

into ppc970.osdl.org:/home/torvalds/v2.6/linux

Call pci_claim_resources() so we can see what PCI resources are being used.

On ia64, the parent resources are not necessarily PCI resources and
so won't get found by pci_find_parent_resource.  Use the shiny new
insert_resource() function instead, which I think we would have used
here had it been available at the time.

If we start again, we can return an error even if we were successful.
Reset the result to 0 before beginning again.  Why don't we use a
tailcall here?

This prevents the "optimize && ?" message appearing when the kernel
configuration tool is run.  The message could be eliminated from the
tool, but I'd rather fix the needlessly over-complicated expression:

into ppc970.osdl.org:/home/torvalds/v2.6/linux

into ppc970.osdl.org:/home/torvalds/v2.6/linux

into ppc970.osdl.org:/home/torvalds/v2.6/linux

We no longer have a CPU_OFFLINE notifier: we freeze the machine and
kill the CPU atomically.  Remove it.

Various files keep per-cpu caches which need to be freed/moved when a
CPU goes down.  All under CONFIG_HOTPLUG_CPU ifdefs.

scsi.c: drain dead cpu's scsi_done_q onto this cpu.

buffer.c: brelse the bh_lrus queue for dead cpu.

timer.c: migrate timers from dead cpu, being careful of lock order vs
	__mod_timer.

radix_tree.c: free dead cpu's radix_tree_preloads

page_alloc.c: empty dead cpu's nr_pagecache_local into nr_pagecache, and
	free pages on cpu's local cache.

slab.c: stop reap_timer for dead cpu, adjust each cache's free limit, and
	free each slab cache's per-cpu block.

swap.c: drain dead cpu's lru_add_pvecs into ours, and empty its committed_space
	counter into global counter.

dev.c: drain device queues from dead cpu into this one.

flow.c: drain dead cpu's flow cache.

Keep track of kswapds: it's OK that they get moved off a node when the
last CPU goes down, but when a CPU comes back, we should try to move
the kswapd back onto its node.

Workqueues need to bring up/destroy the per-cpu thread on cpu up/down.

1) Add a global list of workqueues, and keep the name in the structure
   (to name the newly created thread).

2) Remove BUG_ON in run_workqueue, since thread is dragged off CPU when
   it goes down.

3) Lock out cpu up/down in flush_workqueue, create_workqueue and
   destroy_workqueue.

4) Add notifier to add/destroy workqueue threads, and take over work.

Change ksoftirqd not to assume it's on the CPU: when a cpu goes down,
it will be rudely dragged off.  Since do_softirq() uses
smp_processor_id(), it's easiest to disable preemption, check that the
cpu is still up, then call do_softirq().

If the cpu is actually offline, wait for the notifier, which kills us.

Take over tasklets from dead cpu in the notifier.

Clean up redundant double assignment in CPU_UP callback.

Add hook for RCU to handle jobs on dead cpu.  Requires new
tasklet_kill_immediate for RCU to clean up its tasklet (which might
have been about to run, so tasklet_kill won't work).

Change the migration thread to directly use its cpu arg, rather than
smp_processor_id(): if a cpu goes up then down rapidly, it can be on
the wrong cpu just before it is stopped.

Add code to stop the migration thread on CPU_DEAD and CPU_UP_CANCELED.

Remove the (bogus) priority of the notifier.

We need the migration thread to be RT as soon as the CPU comes online:
for example, stop_machine() (another RT task) expects to yield to it.
Extract the core of setscheduler() and do that when the migration
thread is created.  rq lock is a precaution against the (theoretical)
possibility of someone else doing setscheduer on this thread at the
same time.

Currently the migration thread re-enables irqs, then calls
move_task_away which disables IRQs again and actually does the move.
This means there is a race where the migration thread gets preempted,
and the target CPU can go down.

Hold irqs disabled in migration thread across move_task_away(), which
now doesn't need to save flags (the other caller is the hotplug CPU
code, where irqs are also disabled).