- 27 Sep, 2018 12 commits
-
-
Bruce Allan authored
Update branding strings and remove device ids 0x1594 and 0x1595. Signed-off-by:
Bruce Allan <bruce.w.allan@intel.com> Signed-off-by:
Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
Direct assignment is preferred over a memcpy() Signed-off-by:
-
Jacob Keller authored
When shutting down the controlqs, we check if they are initialized before we shut them down and destroy the lock. This is important, as it prevents attempts to access the lock of an already shutdown queue. Unfortunately, we checked rq.head and sq.head as the value to determine if the queue was initialized. This doesn't work, because head is not reset when the queue is shutdown. In some flows, the adminq will have already been shut down prior to calling ice_shutdown_all_ctrlqs. This can result in a crash due to attempting to access the already destroyed mutex. Fix this by using rq.count and sq.count instead. Indeed, ice_shutdown_sq and ice_shutdown_rq already indicate that this is the value we should be using to determine of the queue was initialized. Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Signed-off-by:
-
Maciej Żenczykowski authored
(the parameters in question are mark and flow_flags) Reviewed-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
Maciej Żenczykowski <maze@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Maciej Żenczykowski authored
(the parameters in question are mark and flow_flags) Reviewed-by:
-
Maxime Chevallier authored
The mvneta controller can handle speeds up to 2500Mbps on the SGMII interface. This relies on serdes configuration, the lane must be configured at 3.125Gbps and we can't use in-band autoneg at that speed. The main issue when supporting that speed on this particular controller is that the link partner can send ethernet frames with a shortened preamble, which if not explicitly enabled in the controller will cause unexpected behaviours. This was tested on Armada 385, with the comphy configuration done in bootloader. Signed-off-by:
Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by:
-
David S. Miller authored
Tonghao Zhang says: ==================== net: vhost: improve performance when enable busyloop This patches improve the guest receive performance. On the handle_tx side, we poll the sock receive queue at the same time. handle_rx do that in the same way. For more performance report, see patch 4 ==================== Signed-off-by: -
Tonghao Zhang authored
This patch improves the guest receive performance. On the handle_tx side, we poll the sock receive queue at the same time. handle_rx do that in the same way. We set the poll-us=100us and use the netperf to test throughput and mean latency. When running the tests, the vhost-net kthread of that VM, is alway 100% CPU. The commands are shown as below. Rx performance is greatly improved by this patch. There is not notable performance change on tx with this series though. This patch is useful for bi-directional traffic. netperf -H IP -t TCP_STREAM -l 20 -- -O "THROUGHPUT, THROUGHPUT_UNITS, MEAN_LATENCY" Topology: [Host] ->linux bridge -> tap vhost-net ->[Guest] TCP_STREAM: * Without the patch: 19842.95 Mbps, 6.50 us mean latency * With the patch: 37598.20 Mbps, 3.43 us mean latency Signed-off-by:
Tonghao Zhang <xiangxia.m.yue@gmail.com> Signed-off-by:
-
Tonghao Zhang authored
Factor out generic busy polling logic and will be used for in tx path in the next patch. And with the patch, qemu can set differently the busyloop_timeout for rx queue. To avoid duplicate codes, introduce the helper functions: * sock_has_rx_data(changed from sk_has_rx_data) * vhost_net_busy_poll_try_queue Signed-off-by:
-
Tonghao Zhang authored
Use the VHOST_NET_VQ_XXX as a subclass for mutex_lock_nested. Signed-off-by:
Jason Wang <jasowang@redhat.com> Signed-off-by:
-
Tonghao Zhang authored
This patch changes the way that lock all vqs at the same, to lock them one by one. It will be used for next patch to avoid the deadlock. Signed-off-by:
-
Yafang Shao authored
After sk_state exposed, we can get in which state this retransmission occurs. That could give us more detail for dignostic. For example, if this retransmission occurs in SYN_SENT state, it may also indicates that the syn packet may be dropped on the remote peer due to syn backlog queue full and then we could check the remote peer. BTW,SYNACK retransmission is traced in tcp_retransmit_synack tracepoint. Signed-off-by:
Yafang Shao <laoar.shao@gmail.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
- 26 Sep, 2018 28 commits
-
-
YueHaibing authored
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t', which is a typedef for an enum type, so make sure the implementation in this driver has returns 'netdev_tx_t' value, and change the function return type to netdev_tx_t. Found by coccinelle. Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
YueHaibing authored
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t', which is a typedef for an enum type, so make sure the implementation in this driver has returns 'netdev_tx_t' value, and change the function return type to netdev_tx_t. Found by coccinelle. Signed-off-by:
-
zhong jiang authored
Trival cleanup, list_move_tail will implement the same function that list_del() + list_add_tail() will do. hence just replace them. Signed-off-by:
zhong jiang <zhongjiang@huawei.com> Signed-off-by:
-
zhong jiang authored
Trival cleanup, list_move_tail will implement the same function that list_del() + list_add_tail() will do. hence just replace them. Signed-off-by:
-
David S. Miller authored
Nikolay Aleksandrov says: ==================== net: bridge: convert bool options to bits A lot of boolean bridge options have been added around the net_bridge structure resulting in holes and more importantly different cache lines that need to be fetched in the fast path. This set moves all of those to bits in a bitfield which resides in a hot cache line thus reducing the size of net_bridge, the number of holes and the number of cache lines needed for the fast path. The set is also sent in preparation for new boolean options to avoid spreading them in the structure and making new holes. One nice side-effect is that we avoid potential race conditions by using the bitops since some of the options were bits being directly set in parallel risking hard to debug issues (has_ipv6_addr). Before: size: 1184, holes: 8, sum holes: 30 After: size: 1160, holes: 3, sum holes: 7 Patch 01 is a trivial style fix Patch 02 adds the new options bitfield and converts the vlan boolean options to bits Patches 03-08 convert the rest of the boolean options to bits Patch 09 re-arranges a few fields in net_bridge to further reduce size v2: patch 09: remove the comment about offload_fwd_mark in net_bridge and leave it where it is now, thanks to Ido for spotting it ==================== Signed-off-by: -
Nikolay Aleksandrov authored
Further reduce the size of net_bridge with 8 bytes and reduce the number of holes in it: Before: holes: 5, sum holes: 15 After: holes: 3, sum holes: 7 Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
-
Nikolay Aleksandrov authored
Convert the last remaining bool option to a bit thus reducing the overall net_bridge size further by 8 bytes. Signed-off-by:
Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
-
Nikolay Aleksandrov authored
Convert the neigh_suppress_enabled option to a bit. Signed-off-by:
-
Nikolay Aleksandrov authored
This patch converts the rest of the mcast options to bits. It also packs the mcast options a little better by moving multicast_mld_version to an existing hole, reducing the net_bridge size by 8 bytes. Signed-off-by:
-
Nikolay Aleksandrov authored
Convert mcast disabled to an option bit and while doing so convert the logic to check if multicast is enabled instead. That is make the logic follow the option value - if it's set then mcast is enabled and vice versa. This avoids a few confusing places where we inverted the value that's being set to follow the mcast_disabled logic. Signed-off-by:
-
Nikolay Aleksandrov authored
Convert group_addr_set internal bridge opt to a bit. Signed-off-by:
-
Nikolay Aleksandrov authored
No functional change, convert of nf_call_[ip|ip6|arp]tables to bits. Signed-off-by:
-
Nikolay Aleksandrov authored
Bridge options have usually been added as separate fields all over the net_bridge struct taking up space and ending up in different cache lines. Let's move them to a single bitfield to save up space and speedup lookups. This patch adds a simple API for option modifying and retrieving using bitops and converts the first user of the API - the bridge vlan options (vlan_enabled and vlan_stats_enabled). Signed-off-by:
-
Nikolay Aleksandrov authored
Currently we have a mix of opening brackets on new lines and on the same line, let's move them all on the same line. Signed-off-by:
-
David S. Miller authored
Julian Wiedmann says: ==================== s390/net: updates 2018-09-26 please apply one more series of cleanups and small improvements for qeth to net-next. Note that one patch needs to touch both af_iucv and qeth, in order to untangle their receive paths. ==================== Signed-off-by: -
Julian Wiedmann authored
The netdevice is always available, apply any carrier state changes to it without caching them. On a STARTLAN event (ie. carrier-up), defer updating the state to qeth_core_hardsetup_card() in the subsequent recovery action. Also remove the carrier-state checks from the xmit routines. Stopping transmission on carrier-down is the responsibility of upper-level code (eg see dev_direct_xmit()). Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by:
-
Julian Wiedmann authored
If qeth_check_ipa_data() consumed an event, there's no point in processing it further. So drop it early, and make the surrounding code a tiny bit more readable. Signed-off-by:
-
Julian Wiedmann authored
Pull one level of checking up into qeth_send_control_data_cb(), and clean up an else-after-return. No functional change. Signed-off-by:
-
Julian Wiedmann authored
We have no code that is waiting for these events, so just drop them when they arrive. Signed-off-by:
-
Julian Wiedmann authored
1. tracing iob->rc makes no sense when it hasn't been modified by the callback, 2. the qeth_dbf_list is declared with LIST_HEAD, which also initializes the list, 3. the ccwgroup core only calls the thaw/restore callbacks if the gdev is online, so we don't have to check for it again. Signed-off-by:
-
Julian Wiedmann authored
The cdev-to-card translation walks through two layers of drvdata, with no locking or refcounting (where eg. the ccwgroup core only accesses a cdev's drvdata while holding the ccwlock). This might be safe for now, but any careless usage of the helper has the potential for subtle races and use-after-free's. Luckily there's only one occurrence where we _really_ need it (in qeth_irq()), for any other user we can just pass through an appropriate card pointer. Signed-off-by:
-
Julian Wiedmann authored
This allows us to remove the CARD_FROM_CDEV calls in the iob callbacks. Signed-off-by:
-
Julian Wiedmann authored
When not using the CQ, this allows us avoid the second skb queue walk in qeth_release_skbs(). Signed-off-by:
-
Julian Wiedmann authored
This was presumably left over from back when qeth recursed into dev_queue_xmit(). Signed-off-by:
-
Julian Wiedmann authored
To match the use of __skb_queue_purge(), also make the skb's enqueue in qeth_fill_buffer() lockless. Signed-off-by:
-
Julian Wiedmann authored
This patch attempts to untangle the TX and RX code in qeth from af_iucv's respective HiperTransport path: On the TX side, pointing skb_network_header() at the IUCV header means that qeth_l3_fill_af_iucv_hdr() no longer needs a magical offset to access the header. On the RX side, qeth pulls the (fake) L2 header off the skb like any normal ethernet driver would. This makes working with the IUCV header in af_iucv easier, since we no longer have to assume a fixed skb layout. While at it, replace the open-coded length checks in af_iucv's RX path with pskb_may_pull(). Signed-off-by:
-
Julian Wiedmann authored
qeth_core_probe_device() sets the gdev's drvdata, but doesn't reset it on a subsequent error. Move the (re-)setting around a bit, so that it happens symmetrically on allocating/freeing the qeth_card struct. This is no actual problem, as the ccwgroup core will discard the gdev on a probe error. But from qeth's perspective the gdev is an external resource, so it's best to manage it cleanly. Signed-off-by:
-
Julian Wiedmann authored
Device initialization code usually first loads a subdriver (via qeth_core_load_discipline()), and then runs its setup() callback. If this fails, it rolls back the load via qeth_core_free_discipline(). qeth_core_free_discipline() expects the options.layer attribute to be initialized, but on error in setup() that's currently not the case. Resulting in misbalanced symbol_put() calls. Fix this by setting options.layer when loading the subdriver. Signed-off-by:
-
