This patch uses the load/store exclusive instructions to add SMP futex
support for ARM.

Since the ARM architecture does not provide instructions for
unprivileged exclusive memory accesses, we can only provide SMP futexes
when CPU domain support is disabled.

Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The ARM kernel supports writethrough data cache via the
CONFIG_CPU_DCACHE_WRITETHROUGH option.  However, that
functionality wasn't implemented in the arch/arm/boot/compressed
code.  It is now necessary due to a new ARM926EJS processor
that has an issue with writeback data cache.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Improve the Kconfig help texts for the phys-to-virt patching feature.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Highmem on ARM has been around for a while now, without any major issues
being raised.  So, drop the experimental status of this feature.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

SMP on ARM has been around for a while now, without any major issues
being raised.  So, drop the experimental status of this feature.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  ceph: do not use i_wrbuffer_ref as refcount for Fb cap
  ceph: fix list_add in ceph_put_snap_realm
  ceph: print debug message before put mds session

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon/nouveau: fix build regression on alpha due to Xen changes.
  drm/radeon/kms: fix cayman acceleration
  drm/radeon: fix cayman struct accessors.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: Fix for the TWL4030 PM sleep/wakeup sequence
  mfd: Fix asic3 build error
  mfd: Fixed gpio polarity of omap-usb gpio USB-phy reset

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] fix alloc_pgste check in init_new_context
  [S390] oprofile: fix min/max interval query checks
  [S390] replace diag10() with diag10_range() function
  [S390] disassembler: handle b280/spp instruction
  [S390] kernel: Initialize register 14 when starting new CPU
  [S390] dasd: prevent IO error during reserve/release loop
  [S390] sclp/memory hotplug: fix initial usecount of increments

This reverts commit f21ca5ff.

Quoth Gustavo F. Padovan:
  "Commit f21ca5ff can cause a NULL
   dereference if we call shutdown in a bluetooth SCO socket and doesn't
   wait the shutdown completion to call close().  Please revert it.  I
   may have a fix for it soon, but we don't have time anymore, so revert
   is the way to go.  ;)"
Requested-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM / Hibernate: Fix ioctl SNAPSHOT_S2RAM
  PM / Hibernate: Make snapshot_release() restore GFP mask
  PM: Fix warning in pm_restrict_gfp_mask() during SNAPSHOT_S2RAM ioctl

include/linux/gfp.h and include/trace/events/gfpflags.h are out of sync.
When tracing is enabled, certain flags are not recognised and the text
output is less useful as a result.  Add the missing flags.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Testing the shmem_swaplist replacements for igrab() revealed another bug:
writes to /dev/loop0 on a tmpfs file which fills its filesystem were
sometimes failing with "Buffer I/O error"s.

These came from ENOSPC failures of shmem_getpage(), when racing with
swapoff: the same could happen when racing with another shmem_getpage(),
pulling the page in from swap in between our find_lock_page() and our
taking the info->lock (though not in the single-threaded loop case).

This is unacceptable, and surprising that I've not noticed it before:
it dates back many years, but (presumably) was made a lot easier to
reproduce in 2.6.36, which sited a page preallocation in the race window.

Fix it by rechecking the page cache before settling on an ENOSPC error.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The use of igrab() in swapoff's shmem_unuse_inode() is just as vulnerable
to umount as that in shmem_writepage().

Fix this instance by extending the protection of shmem_swaplist_mutex
right across shmem_unuse_inode(): while it's on the list, the inode cannot
be evicted (and the filesystem cannot be unmounted) without
shmem_evict_inode() taking that mutex to remove it from the list.

But since shmem_writepage() might take that mutex, we should avoid making
memory allocations or memcg charges while holding it: prepare them at the
outer level in shmem_unuse().  When mem_cgroup_cache_charge() was
originally placed, we didn't know until that point that the page from swap
was actually a shmem page; but nowadays it's noted in the swap_map, so
we're safe to charge upfront.  For the radix_tree, do as is done in
shmem_getpage(): preload upfront, but don't pin to the cpu; so we make a
habit of refreshing the node pool, but might dip into GFP_NOWAIT reserves
on occasion if subsequently preempted.

With the allocation and charge moved out from shmem_unuse_inode(),
we can also hold index map and info->lock over from finding the entry.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Konstanin Khlebnikov reports that a dangerous race between umount and
shmem_writepage can be reproduced by this script:

  for i in {1..300} ; do
	mkdir $i
	while true ; do
		mount -t tmpfs none $i
		dd if=/dev/zero of=$i/test bs=1M count=$(($RANDOM % 100))
		umount $i
	done &
  done

on a 6xCPU node with 8Gb RAM: kernel very unstable after this accident. =)

Kernel log:

  VFS: Busy inodes after unmount of tmpfs.
                 Self-destruct in 5 seconds.  Have a nice day...

  WARNING: at lib/list_debug.c:53 __list_del_entry+0x8d/0x98()
  list_del corruption. prev->next should be ffff880222fdaac8, but was (null)
  Pid: 11222, comm: mount.tmpfs Not tainted 2.6.39-rc2+ #4
  Call Trace:
   warn_slowpath_common+0x80/0x98
   warn_slowpath_fmt+0x41/0x43
   __list_del_entry+0x8d/0x98
   evict+0x50/0x113
   iput+0x138/0x141
  ...
  BUG: unable to handle kernel paging request at ffffffffffffffff
  IP: shmem_free_blocks+0x18/0x4c
  Pid: 10422, comm: dd Tainted: G        W   2.6.39-rc2+ #4
  Call Trace:
   shmem_recalc_inode+0x61/0x66
   shmem_writepage+0xba/0x1dc
   pageout+0x13c/0x24c
   shrink_page_list+0x28e/0x4be
   shrink_inactive_list+0x21f/0x382
  ...

shmem_writepage() calls igrab() on the inode for the page which came from
page reclaim, to add it later into shmem_swaplist for swapoff operation.

This igrab() can race with super-block deactivating process:

  shrink_inactive_list()          deactivate_super()
  pageout()                       tmpfs_fs_type->kill_sb()
  shmem_writepage()               kill_litter_super()
                                  generic_shutdown_super()
                                   evict_inodes()
   igrab()
                                    atomic_read(&inode->i_count)
                                     skip-inode
   iput()
                                   if (!list_empty(&sb->s_inodes))
                                          printk("VFS: Busy inodes after...

This igrap-iput pair was added in commit 1b1b32f2 "tmpfs: fix
shmem_swaplist races" based on incorrect assumptions: igrab() protects the
inode from concurrent eviction by deletion, but it does nothing to protect
it from concurrent unmounting, which goes ahead despite the raised
i_count.

So this use of igrab() was wrong all along, but the race made much worse
in 2.6.37 when commit 63997e98 "split invalidate_inodes()" replaced
two attempts at invalidate_inodes() by a single evict_inodes().

Konstantin posted a plausible patch, raising sb->s_active too: I'm unsure
whether it was correct or not; but burnt once by igrab(), I am sure that
we don't want to rely more deeply upon externals here.

Fix it by adding the inode to shmem_swaplist earlier, while the page lock
on page in page cache still secures the inode against eviction, without
artifically raising i_count.  It was originally added later because
shmem_unuse_inode() is liable to remove an inode from the list while it's
unswapped; but we can guard against that by taking spinlock before
dropping mutex.
Reported-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Hugh Dickins <hughd@google.com>
Tested-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit dde79e00 ("page_cgroup: reduce allocation overhead for
page_cgroup array for CONFIG_SPARSEMEM") added a regression that the
memory cgroup data structures all end up in node 0 because the first
attempt at allocating them would not pass in a node hint.  Since the
initialization runs on CPU #0 it would all end up node 0.  This is a
problem on large memory systems, where node 0 would lose a lot of
memory.

Change the alloc_pages_exact() to alloc_pages_exact_nid().  This will
still fall back to other nodes if not enough memory is available.

 [ RED-PEN: right now it would fall back first before trying
   vmalloc_node.  Probably not the best strategy ...  But I left it like
   that for now. ]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Reported-by: Doug Nelson
Cc: David Rientjes <rientjes@google.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add a alloc_pages_exact_nid() that allocates on a specific node.

The naming is quite broken, but fixing that would need a larger renaming
action.

[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: tweak comment]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: David Rientjes <rientjes@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Take alphabetical orders for MAINTAINERS file.
Signed-off-by: Harry Wei <harryxiyou@gmail.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Stefan found nobootmem does not work on his system that has only 8M of
RAM.  This causes an early panic:

  BIOS-provided physical RAM map:
   BIOS-88: 0000000000000000 - 000000000009f000 (usable)
   BIOS-88: 0000000000100000 - 0000000000840000 (usable)
  bootconsole [earlyser0] enabled
  Notice: NX (Execute Disable) protection missing in CPU or disabled in BIOS!
  DMI not present or invalid.
  last_pfn = 0x840 max_arch_pfn = 0x100000
  init_memory_mapping: 0000000000000000-0000000000840000
  8MB LOWMEM available.
    mapped low ram: 0 - 00840000
    low ram: 0 - 00840000
  Zone PFN ranges:
    DMA      0x00000001 -> 0x00001000
    Normal   empty
  Movable zone start PFN for each node
  early_node_map[2] active PFN ranges
      0: 0x00000001 -> 0x0000009f
      0: 0x00000100 -> 0x00000840
  BUG: Int 6: CR2 (null)
       EDI c034663c  ESI (null)  EBP c0329f38  ESP c0329ef4
       EBX c0346380  EDX 00000006  ECX ffffffff  EAX fffffff4
       err (null)  EIP c0353191   CS c0320060  flg 00010082
  Stack: (null) c030c533 000007cd (null) c030c533 00000001 (null) (null)
         00000003 0000083f 00000018 00000002 00000002 c0329f6c c03534d6 (null)
         (null) 00000100 00000840 (null) c0329f64 00000001 00001000 (null)
  Pid: 0, comm: swapper Not tainted 2.6.36 #5
  Call Trace:
   [<c02e3707>] ? 0xc02e3707
   [<c035e6e5>] 0xc035e6e5
   [<c0353191>] ? 0xc0353191
   [<c03534d6>] 0xc03534d6
   [<c034f1cd>] 0xc034f1cd
   [<c034a824>] 0xc034a824
   [<c03513cb>] ? 0xc03513cb
   [<c0349432>] 0xc0349432
   [<c0349066>] 0xc0349066

It turns out that we should ignore the low limit of 16M.

Use alloc_bootmem_node_nopanic() in this case.

[akpm@linux-foundation.org: less mess]
Signed-off-by: Yinghai LU <yinghai@kernel.org>
Reported-by: Stefan Hellermann <stefan@the2masters.de>
Tested-by: Stefan Hellermann <stefan@the2masters.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>		[2.6.34+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The lru_deactivate_fn should not move page which in on unevictable lru
into inactive list.  Otherwise, we can meet BUG when we use
isolate_lru_pages as __isolate_lru_page could return -EINVAL.
Reported-by: Ying Han <yinghan@google.com>
Tested-by: Ying Han <yinghan@google.com>
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: Rik van Riel<riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The driver is not balancing set_irq and disable_irq_wake() calls, so
ensure that it keeps track of whether the wake is enabled.

The fixes the following error on S3C6410 devices:

  WARNING: at kernel/irq/manage.c:382 set_irq_wake+0x84/0xec()
  Unbalanced IRQ 92 wake disable
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The SNAPSHOT_S2RAM ioctl used for implementing the feature allowing
one to suspend to RAM after creating a hibernation image is currently
broken, because it doesn't clear the "ready" flag in the struct
snapshot_data object handled by it.  As a result, the
SNAPSHOT_UNFREEZE doesn't work correctly after SNAPSHOT_S2RAM has
returned and the user space hibernate task cannot thaw the other
processes as appropriate.  Make SNAPSHOT_S2RAM clear data->ready
to fix this problem.
Tested-by: Alexandre Felipe Muller de Souza <alexandrefm@mandriva.com.br>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org

If the process using the hibernate user space interface closes
/dev/snapshot after creating a hibernation image without thawing
tasks, snapshot_release() should call pm_restore_gfp_mask() to
restore the GFP mask used before the creation of the image.  Make
that happen.
Tested-by: Alexandre Felipe Muller de Souza <alexandrefm@mandriva.com.br>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org

A warning is printed by pm_restrict_gfp_mask() while the
SNAPSHOT_S2RAM ioctl is being executed after creating a hibernation
image, because pm_restrict_gfp_mask() has been called once already
before the image creation and suspend_devices_and_enter() calls it
once again.  This happens after commit 452aa699
(mm/pm: force GFP_NOIO during suspend/hibernation and resume).

To avoid this issue, move pm_restrict_gfp_mask() and
pm_restore_gfp_mask() from suspend_devices_and_enter() to its caller
in kernel/power/suspend.c.
Reported-by: Alexandre Felipe Muller de Souza <alexandrefm@mandriva.com.br>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org

We increments i_wrbuffer_ref when taking the Fb cap. This breaks
the dirty page accounting and causes looping in
__ceph_do_pending_vmtruncate, and ceph client hangs.

This bug can be reproduced occasionally by running blogbench.

Add a new field i_wb_ref to inode and dedicate it to Fb reference
counting.
Signed-off-by: Henry C Chang <henry.cy.chang@gmail.com>
Signed-off-by: Sage Weil <sage@newdream.net>

Signed-off-by: Henry C Chang <henry.cy.chang@gmail.com>
Signed-off-by: Sage Weil <sage@newdream.net>

The mds session, s, could be freed during ceph_put_mds_session.
Move dout before ceph_put_mds_session.
Signed-off-by: Henry C Chang <henry.cy.chang@gmail.com>
Signed-off-by: Sage Weil <sage@newdream.net>

Only configure sleep script when the flag is TWL4030_SLEEP_SCRIPT.

Adding the missing brackets for fixing the issue.
Signed-off-by: Lesly A M <leslyam@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: David Derrick <dderrick@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Fix below compile error:

  CC      drivers/mfd/asic3.o
drivers/mfd/asic3.c: In function 'asic3_irq_demux':
drivers/mfd/asic3.c:147: error: 'irq_data' undeclared (first use in this function)
drivers/mfd/asic3.c:147: error: (Each undeclared identifier is reported only once
drivers/mfd/asic3.c:147: error: for each function it appears in.)
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

With commit 19403165 a main part of ehci-omap.c moved to
drivers/mfd/omap-usb-host.c created by commit 17cdd29d.
Due to this reorganisation the polarity used to reset the
external USB phy changed and USB host doesn't recognize
any devices.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The Xen changes were using DMA_ERROR_CODE which isn't defined on a few
platforms, however we reverted the Xen patch that caused use to try and
use this code path earlier in 2.6.39 cycle, so for now lets just force
the code to never take this path and allow it to build again on alpha.

The proper long term answer is probably to store if the dma_addr has
been assigned to alongside the dma_addr in the higher level code,
though I think Thomas wanted to rewrite most of this anyways properly.
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The TCC disable setup was incorrect.  This
prevents the GPU from hanging when draw commands
are issued.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

We are accessing totally the wrong struct in this case, and putting
uninitialised values into the GPU, which it doesn't like unsurprisingly.
Signed-off-by: Dave Airlie <airlied@redhat.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
  slcan: fix ldisc->open retval
  net/usb: mark LG VL600 LTE modem ethernet interface as WWAN
  xfrm: Don't allow esn with disabled anti replay detection
  xfrm: Assign the inner mode output function to the dst entry
  net: dev_close() should check IFF_UP
  vlan: fix GVRP at dismantle time
  netfilter: revert a2361c87
  netfilter: IPv6: fix DSCP mangle code
  netfilter: IPv6: initialize TOS field in REJECT target module
  IPVS: init and cleanup restructuring
  IPVS: Change of socket usage to enable name space exit.
  netfilter: ebtables: only call xt_compat_add_offset once per rule
  netfilter: fix ebtables compat support
  netfilter: ctnetlink: fix timestamp support for new conntracks
  pch_gbe: support ML7223 IOH
  PCH_GbE : Fixed the issue of checksum judgment
  PCH_GbE : Fixed the issue of collision detection
  NET: slip, fix ldisc->open retval
  be2net: Fixed bugs related to PVID.
  ehea: fix wrongly reported speed and port
  ...

This reverts commit 4a5fa359, which did not allow SLUB to be used
on architectures that use DISCONTIGMEM without compiling NUMA support
without CONFIG_BROKEN also set.

The slub panic that it was intended to prevent is addressed by
d9b41e0b ("[PARISC] set memory ranges in N_NORMAL_MEMORY when
onlined") on parisc so there is no further slub issues with such a
configuration.

The reverts allows SLUB now to be used on such architectures since
there haven't been any reports of additional errors.

Cc: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

TTY layer expects 0 if the ldisc->open operation succeeded.
Reported-by: Matvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Like other mobile broadband device ethernet interfaces, mark the LG
VL600 with the 'wwan' devtype so userspace knows it needs additional
configuration via the AT port before the interface can be used.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unlike the standard case, disabled anti replay detection needs some
nontrivial extra treatment on ESN. RFC 4303 states:

Note: If a receiver chooses to not enable anti-replay for an SA, then
the receiver SHOULD NOT negotiate ESN in an SA management protocol.
Use of ESN creates a need for the receiver to manage the anti-replay
window (in order to determine the correct value for the high-order
bits of the ESN, which are employed in the ICV computation), which is
generally contrary to the notion of disabling anti-replay for an SA.

So return an error if an ESN state with disabled anti replay detection
is inserted for now and add the extra treatment later if we need it.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As it is, we assign the outer modes output function to the dst entry
when we create the xfrm bundle. This leads to two problems on interfamily
scenarios. We might insert ipv4 packets into ip6_fragment when called
from xfrm6_output. The system crashes if we try to fragment an ipv4
packet with ip6_fragment. This issue was introduced with git commit
ad0081e4 (ipv6: Fragment locally generated tunnel-mode IPSec6 packets
as needed). The second issue is, that we might insert ipv4 packets in
netfilter6 and vice versa on interfamily scenarios.

With this patch we assign the inner mode output function to the dst entry
when we create the xfrm bundle. So xfrm4_output/xfrm6_output from the inner
mode is used and the right fragmentation and netfilter functions are called.
We switch then to outer mode with the output_finish functions.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>