Fixes commit 54da20d8 ("ath9k_hw: improve ANI processing and rx desensitizing parameters")

Call ath9k_ani_restart() only when the phy error rate reach the
ANI immunity threshold. Sync the logic with internal code base.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

drivers/net/wireless/ath/ath9k/channel.c:230: warning: type qualifiers ignored on function return type
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Used in some newer TP-Link AR9533 devices.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

In the current solution wil6210 configures the vring in a worker
and holds only one pending CID. This implementation may lead to
race conditions between connect and disconnect events of multiple
stations or fast connect/disconnect events of the same station.

In order to allow the removal of the connect worker and handling of
WMI_VRING_CFG_DONE_EVENTID in the connect event, the WMI replies
that provide the reply in a given buffer needs to be handled
immediately in the WMI event interrupt thread.
To prevent deadlocks, WMI replies that requires additional
handling are still handled via the events list.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

In TX vring allocation, vring_tx->va is allocated before WMI command to
configure the vring is sent to the device. As the WMI command can take
time to complete, it can lead to scenarios where vring_tx->va is not NULL
but vring is still not enabled.

This patch adds a check that vring_tx_data is enabled before returning
a valid TX vring.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

wil_vring_fini_tx is called in disconnect in order to free the
allocated vrings.
wil_vring_fini_tx is disabling the vring_tx_data before napi_synchronize
is called in order to avoid the tx handling of this vring, while
wil_vring_free is called only after napi finished the current handling
of the tx completed packets.
Due to that, in case of disconnect, wil6210_netdev_poll_tx can be called
when vring->va is not NULL but vring_tx_data[i]->enabled is already
disabled.

This patch checks vring_tx_data[i]->enabled in wil6210_netdev_poll_tx
to prevent handling of disabled vrings.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

In the start_ap/change_beacon API, when we set up probe response
offloading, we only use the IE list from the probe response
template and not the IE list from the proberesp_ies argument.
As a result, we miss important IEs and it causes problems with
some scenarios such as P2P.
With this change, we merge the list of IEs from the probe response
template and proberesp_ies and send the merged list to the FW
for offloading. It is still FW responsibility to filter out
irrelevant IEs when sending probe response, based on the actual
contents of the probe request.
Also in case association response termplate is not provided,
we will use the merged list of IEs from probe response in the
association response as well.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Currently the privacy flag calculation in change_beacon
checks for RSN IE inside proberesp_ies, but normally it
is not found there. It works today because of code inside
the function wil_fix_bcon, but wil_fix_bcon is not directly
related to change_beacon, and it may be changed or removed
in the future and break the calculation.
To fix this issue, change the privacy flag calculation
to check RSN IE inside the beacon itself. The new check is more
reliable and will not be sensitive to changes in wil_fix_bcon.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This device is available under different marketing names:
WLM-20U2 - Wireless USB Dongle for Toshiba TVs
GN-1080 - Wireless LAN Module for Toshiba MFPs.
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Request NOA update when chanctx active, also in case
of STA.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The p2p NOA never been supported at 10.2.4 FW, remove it to avoid SWBA
event parse error for multi beacon interval case.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add debugfs support for per client total rx duration, track this
via the report of Peer stats rx duration reported for every 500ms
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Register for 500ms as periodic peer stats update period,
and parameters like rx_duration that needs to be tracked
in host can be achieved by this provision, also periodic
stats update is the future of fw_stats and shall be extended
for pdev / vdev stats irrespecitive PEER_STATS service is enabled
or not
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: fix a checkpatch warning]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Enable support for periodic peer stats update when peer stats
service is enabled. The host to update the peer stats received
from the firmware periodically, since firmware will reset this to zero
after sometime (due to memory constraints)

While enabling periodic peer / vdev stats cleanup the existing
list in debugfs if max limit is reached, so that the new stats is
updated.

Ideally speaking based on 'Michal Kazior's' suggestion
we need to completely move to periodic update of all the stats making
the 'ping - pong' method obselete. This requires a bit of re-work and
some testing as well, also confirmation regarding backward comptability
for various firmware and chipsets. Hence allow periodic update only
for peer_stats.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Prerequisite patch to address checkpatch errors for the next patch
in this series, this function names are bit too long, make it short
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Replace the local variable 'burst_enable' with 'param'
for mapping and setting pdev paraemeters and with this patch
pretty easy to extend support for new parameters adhering to
linux kernel coding guidelines
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Fix naming of peer stats rssi_changed field in 10.2.4 to make it
more readable. As of now this field is not used, but necessary to
pull in fw_stats with appropriate length.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add support for parsing 'peer_rx_duration' as part
of 10.2.4 peer_stats. Also register PEER_STATS service
for parsing 'rx_duration' (and for any new fields to be added
as part of peer_stats). Have checks for backward compatibility with
older 10.2.4 firmware incase PEER_STATS service is not enabled
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

On multicore systems it was possible for the txrx
tasklet to keep on running for long periods of
time on a single CPU due to tx completion
processing. Another CPU could feed the running
tasklet for an indefinite amount of time.

The tasklet is now guaranteed to run a finite
amount of time and is limited by HTT CE Rx ring
depth.

This improves behavior when RPS is used on target
system and might improve TCP handling as well.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add device tree binding documentation details for wifi block present
in Qualcomm IPQ4019 SoC into "qcom,ath10k.txt".

Right now, ath10k wireless driver has support for PCI based wlan devices.
There is a plan to extend ath10k driver to support wifi devices which are
connected over AHB as well (enumeration will happen via device tree node).
For AHB based devices (ie, ipq4019), all wifi properties are supplied via
device tree (including irq, reg addr, cal data,etc).
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Acked-by: Rob Herring <robh@kernel.org>
[kvalo@qca.qualcomm.com: fixed typos noticed by Rob]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Sometimes on module reload and reconnect to ibss a deauth from
other station can be received. This is treated as a link down but
for ibss this is wrong. It will close the interface and no data
is possible. Ignore the firmware generated link down events in
ibss mode, as ibss is always teared down by cfg80211.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The btcoex uses a timeout which was in milliseconds and got
converted to jiffies upon using timer api. Instead, convert
it to jiffies and treat it as such further.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Instead to having macro definition for millisecond timeout have
the definition directly in jiffies. This makes the unit of the
value immediately clear and may result in code that is bit more
compact.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The function brcmf_sdio_wd_timer() has wdtick parameter. However, it
is only called with two values and as such the parameter is replaced
with boolean value indicating the timer should be active or not.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Function prototype forward declarations are to be avoided. This
patch shuffles some of the functions so the forward declarations
can be removed.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

With wowl net detect it becomes possible to scan for specific ssids
and wakeup once found.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2016-01-07_2' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

* bug fixes and improvements for firmware debug system (Golan and myself)
* fixes for D0i3 (Eliad)
* prevent muliple stations with the same MAC address
* advertise support for Rx A-MSDU in A-MPDU
* scan related fixes
* support -20.ucode
* fix WoWLAN for iwldvm
* preparations towards multiple Rx queues
* platform power improvements for GO mode when no clients are associated

No major changes to list.

8000 device family has a new debug engine that needs to be
configured differently than 7000's.
The debug engine's DMA works in chunks of memory and the
size of the buffer really means the start of the last
chunk. Since one chunk is 256-byte long, we should
configure the device to write to buffer_size - 256.
This fixes a situation were the device would write to
memory it is not allowed to access.

CC: <stable@vger.kernel.org> [4.1+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When iwl_mvm_fw_error_dump fails, it needs to clear the
state in mvm, which includes:
	* clear IWL_MVM_STATUS_DUMPING_FW_LOG
	* set mvm->fw_dump_trig to NULL
	* free the description

While at it, remove a NULL check in
iwl_mvm_free_fw_dump_desc since kfree is NULL safe.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The debug functions of fw-dbg.c don't really need to modify
the trigger and the description they receive as a parameter.
Constify the pointers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This notification will be extended with extra data, so just
check that it has a minimum length, not the exact length;
we might later add handling for the extra fields added and
have more code to handle both versions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

gtkdata->mvm wasn't set in iwl_mvm_d0i3_update_keys,
resulting in kernel panic in some flows (when mvm
is actually used...)

Fixes: a3f7ba5c ("iwlwifi: update key params on d0i3 entrance/exit")
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

As we're working on multi-queue RX, we want to parallelise checking
the PN in order to avoid having to serialise the RX processing.

It may seem that doing parallel PN checking is insecure, but it turns
out to be OK because queue assignment is done based on the data in the
frame (IP/TCP) and thus cannot be manipulated by an attacker, since
the data is encrypted and must first have been decrypted successfully.

There are some corner cases, in particular when the peer starts using
fragmentation which redirects the packet to the default queue. However
this redirection is remembered (for the STA, per TID) and thus cannot
be exploited by an attacker either.

Leave checking on the default queue (queue 0) to mac80211, since we
get fragmented packets there and those are subject to stricter checks
during reassembly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The commit below called iwl_mvm_mac_ctxt_changed() to handle
a case that the vif is a P2P GO.
However iwl_mvm_mac_ctxt_cmd_go() ignores the number of
associated stations and asks the FW to pass beacons anyways.

Fix this by checking ap_assoc_sta_count parameter, in iwl_mvm_mac_ctxt_cmd_go()
as well, and ask the FW to pass beacons only when there's
at least one associated station.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

As the device (and parts of the driver) cannot deal with having the
same MAC address for two stations (on two virtual interfaces), add
some explicit code to prevent this case.

Note that in practice this cannot happen since the device doesn't
support operating with two AP/GO interfaces at the same time either,
and other scenarios for this are, while not impossible, not going to
happen in practice.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We advertise one STATION vif only, so this just can't
happen. Remove this useless WARN_ON.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Since A-MPDU deaggregation is done in hardware, and A-MSDU deaggregation
is done in software, there's no reason not to support A-MSDU in A-MPDU;
set the flag to support it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Allow the user to configure a non-trigger session - a window
between triggers in which the driver won't collect fw debug data.
This can be useful when the frequent collection of fw data
has an impact on the performance, such as debugging
tx flows.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Dumping the content of the radio registers greatly helps
to debug PHY issues, which can lead to TFD queue hang.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>