Announce the new x86 MCE infrastructure maintainers.
Acked-by: Borislav Petkov <bp@amd64.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/n/tip-8hs7yob6wib4vblmrmbpbav4@git.kernel.orgSigned-off-by: Ingo Molnar <mingo@elte.hu>

Commit 916f676f started reserving boot service code since some systems
require you to keep that code around until SetVirtualAddressMap is called.

However, in some cases those areas will overlap with reserved regions.
The proper medium-term fix is to fix the bootloader to prevent the
conflicts from occurring by moving the kernel to a better position,
but the kernel should check for this possibility, and only reserve regions
which can be reserved.
Signed-off-by: Maarten Lankhorst <m.b.lankhorst@gmail.com>
Link: http://lkml.kernel.org/r/4DF7A005.1050407@gmail.comAcked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

In isofs_fill_super(), when an iso_primary_descriptor is found, it is
kept in pri_bh.  The error cases don't properly release it.  Fix it.
Reported-and-tested-by: 김원석 <stanley.will.kim@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/i915: Fix gen6 (SNB) missed BLT ring interrupts.

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] powernow-k8: Don't try to transition if the pstate is incorrect
  [CPUFREQ] powernow-k8: Don't notify of successful transition if we failed (vid case).
  [CPUFREQ] Don't set stat->last_index to -1 if the pol->cur has incorrect value.

* anon_vma-locking:
  mm: avoid anon_vma_chain allocation under anon_vma lock
  mm: avoid repeated anon_vma lock/unlock sequences in unlink_anon_vmas()
  mm: avoid repeated anon_vma lock/unlock sequences in anon_vma_clone()

Hugh Dickins points out that lockdep (correctly) spots a potential
deadlock on the anon_vma lock, because we now do a GFP_KERNEL allocation
of anon_vma_chain while doing anon_vma_clone().  The problem is that
page reclaim will want to take the anon_vma lock of any anonymous pages
that it will try to reclaim.

So re-organize the code in anon_vma_clone() slightly: first do just a
GFP_NOWAIT allocation, which will usually work fine.  But if that fails,
let's just drop the lock and re-do the allocation, now with GFP_KERNEL.

End result: not only do we avoid the locking problem, this also ends up
getting better concurrency in case the allocation does need to block.
Tim Chen reports that with all these anon_vma locking tweaks, we're now
almost back up to the spinlock performance.
Reported-and-tested-by: Hugh Dickins <hughd@google.com>
Tested-by: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This matches the anon_vma_clone() case, and uses the same lock helper
functions.  Because of the need to potentially release the anon_vma's,
it's a bit more complex, though.

We traverse the 'vma->anon_vma_chain' in two phases: the first loop gets
the anon_vma lock (with the helper function that only takes the lock
once for the whole loop), and removes any entries that don't need any
more processing.

The second phase just traverses the remaining list entries (without
holding the anon_vma lock), and does any actual freeing of the
anon_vma's that is required.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Hugh Dickins <hughd@google.com>
Tested-by: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In anon_vma_clone() we traverse the vma->anon_vma_chain of the source
vma, locking the anon_vma for each entry.

But they are all going to have the same root entry, which means that
we're locking and unlocking the same lock over and over again.  Which is
expensive in locked operations, but can get _really_ expensive when that
root entry sees any kind of lock contention.

In fact, Tim Chen reports a big performance regression due to this: when
we switched to use a mutex instead of a spinlock, the contention case
gets much worse.

So to alleviate this all, this commit creates a small helper function
(lock_anon_vma_root()) that can be used to take the lock just once
rather than taking and releasing it over and over again.

We still have the same "take the lock and release" it behavior in the
exit path (in unlink_anon_vmas()), but that one is a bit harder to fix
since we're actually freeing the anon_vma entries as we go, and that
will touch the lock too.
Reported-and-tested-by: Tim Chen <tim.c.chen@linux.intel.com>
Tested-by: Hugh Dickins <hughd@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The failure appeared in dmesg as:

[drm:i915_hangcheck_ring_idle] *ERROR* Hangcheck timer elapsed... blt
ring idle [waiting on 35064155, at 35064155], missed IRQ?

This works around that problem on by making the blitter command
streamer write interrupt state to the Hardware Status Page when a
MI_USER_INTERRUPT command is decoded, which appears to force the seqno
out to memory before the interrupt happens.

v1->v2: Moved to prior interrupt handler installation and RMW flags as
per feedback.
v2->v3: Removed RMW of flags (by anholt)

Cc: stable@kernel.org
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> [v1]
Tested-by: Eric Anholt <eric@anholt.net> [v1,v3]
	   (incidence of the bug with a testcase went from avg 2/1000 to
	   0/12651 in the latest test run (plus more for v1))
Tested-by: Kenneth Graunke <kenneth@whitecape.org> [v1]
Tested-by: Robert Hooker <robert.hooker@canonical.com> [v1]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=33394Signed-off-by: Dave Airlie <airlied@redhat.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Fix no NID error with VIA codecs
  ALSA: isight: adjust for new queueing API
  ALSA: 6fire - Fix signedness bug
  ALSA: lola - Fix section mismatch
  ALSA: hda - Fix missing static inline to beep dummy function
  ALSA: 6fire: Fix double-free bug in usb6fire_fw_ezusb_upload()
  ALSA: hda - Fix beep_device compilation warnings
  ALSA: hda - Fix wrong auto-mute type for Acer Aspire-one
  ALSA: emu10k1: Add details for E-mu 0404 PCIe version
  ALSA: hdspm - Add firmware revision ID for RME MADI PCI version
  ALSA: hdspm - Fix jumping external wordclock frequency in AutoSync mode
  ALSA: hdspm - Fix locking in snd_hdspm_midi_input_read

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: make log devices with write back caches work
  xfs: fix ->mknod() return value on xfs_get_acl() failure

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  Revert "HID: magicmouse: ignore 'ivalid report id' while switching modes"
  HID: hid-multitouch: fix broken eGalax
  HID: MAINTAINERS: Update USB HID/HIDBP DRIVERS pattern
  HID: hid-multitouch: add support for Chunghwa multi-touch panel
  HID: hiddev: fix use after free in hiddev_release
  HID: add quirk for HyperPen 10000U
  HID: hiddev: fix potential use-after-free

* 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6:
  gpio: add GPIOF_ values regardless on kconfig settings
  gpio: include linux/gpio.h where needed
  gpio/omap4: Fix missing interrupts during device wakeup due to IOPAD.

* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
  spi/bfin_spi: fix handling of default bits per word setting

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  OMAP1: PM: register notifiers with generic clock ops even when !PM_RUNTIME
  omap: pandora: fix NAND support
  OMAP: PM: omap_device: fix device power domain callbacks
  OMAP: PM debug: fix section mismatch warnings

____call_usermodehelper() now erases any credentials set by the
subprocess_inf::init() function.  The problem is that commit
17f60a7d ("capabilites: allow the application of capability limits
to usermode helpers") creates and commits new credentials with
prepare_kernel_cred() after the call to the init() function.  This wipes
all keyrings after umh_keys_init() is called.

The best way to deal with this is to put the init() call just prior to
the commit_creds() call, and pass the cred pointer to init().  That
means that umh_keys_init() and suchlike can modify the credentials
_before_ they are published and potentially in use by the rest of the
system.

This prevents request_key() from working as it is prevented from passing
the session keyring it set up with the authorisation token to
/sbin/request-key, and so the latter can't assume the authority to
instantiate the key.  This causes the in-kernel DNS resolver to fail
with ENOKEY unconditionally.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Eric Paris <eparis@redhat.com>
Tested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The default bits per word setting should be 8 bits, but since most of our
devices have been explicitly setting this up, we didn't notice when the
default stopped working.

At the moment, any default transfers without an explicit bit size setting
error out with:
bfin-spi bfin-spi.0: transfer: unsupported bits_per_word

So in the transfer logic, have a bits_per_word setting of 0 fall into the
8 bit transfer logic.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

The via driver spews warnigs like
	hda-codec: no NID for mapping control Independent HP:0:0
with some codecs because snd_hda_add_nid() is called with nid=0.
This patch fixes it by skipping the call when no corresponding widget
is found.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Since commit 13882a82 (optimize iso queueing by setting
wake only after the last packet), drivers are required to call
fw_iso_context_queue_flush() after queueing a batch of packets.
The missing call would have an effect only if the controller
queue underruns, but then the DMA would stop completely.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon/kms: use helper functions for fence read/write
  drm/radeon/kms: set DP link config properly for DP bridges
  drm/radeon/kms/atom: AdjustPixelClock fixes for DP bridges
  drm/radeon/kms: fix handling of DP to LVDS bridges
  drm/radeon/kms: issue blank/unblank commands for ext encoders
  drm/radeon/kms: fix support for DDC on dp bridges
  drm/radeon/kms: add support for load detection on dp bridges
  drm/radeon/kms: add missing external encoder action
  drm/radeon/kms: rework atombios_get_encoder_mode()
  drm/radeon/kms: fix num crtcs for Cedar and Caicos
  Revert "drm/i915: Enable GMBUS for post-gen2 chipsets"
  drivers/gpu/drm: use printk_ratelimited instead of printk_ratelimit
  drm/radeon: workaround a hw bug on some radeon chipsets with all-0 EDIDs.
  drm: make debug levels match in edid failure code.
  drm/radeon/kms: clear wb memory by default
  drm/radeon/kms: be more pedantic about the g5 quirk (v2)
  drm/radeon/kms: signed fix for evergreen thermal
  drm: populate irq_by_busid-member for pci

The existing code assumed scratch registers in a number
of places while in most cases we are be using writeback
and events rather than scratch registers.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

DP clock and lanes were not set properly for DP bridges.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Need to set the external transmitter type properly in
AdjustPixelClock to get the properly output.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

They need to be treated like eDP rather than DP.

May fix:
https://bugzilla.kernel.org/show_bug.cgi?id=34822Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Required for DPMS on some systems.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Need to set up the bridge for DDC prior to the
i2c over aux transaction.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

dp to vga bridges for example.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

required for ddc.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This should give us more reliable results if the table
is called before an active device is set.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Only support 4 rather than 6.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Revert commit 8f9a3f9b. This fixes a
hang when loading the eeprom driver (see bug #35572.) GMBUS will be
re-enabled later, differently.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reported-by: Marek Otahal <markotahal@gmail.com>
Tested-by: Yermandu Patapitafious <yermandu.dev@gmail.com>
Tested-by: Andrew Lutomirski <luto@mit.edu>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/linux-2.6-nsfd:
  proc: Fix Oops on stat of /proc/<zombie pid>/ns/net

swapcache will reach the below code path in migrate_page_move_mapping,
and swapcache is accounted as NR_FILE_PAGES but it's not accounted as
NR_SHMEM.

Hugh pointed out we must use PageSwapCache instead of comparing
mapping to &swapper_space, to avoid build failure with CONFIG_SWAP=n.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch augments the pstate transition code to error out
(instead of returning 0) when an incorrect pstate is provided.
Suggested-by: Borislav Petkov <bp@alien8.de>
CC: andre.przywara@amd.com
CC: Mark.Langsdorf@amd.com
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Dave Jones <davej@redhat.com>

Before this patch if we failed the vid transition would still try to
submit the "new" frequencies to cpufreq.
That is incorrect - also we could submit a non-existing frequency value
which would cause cpufreq to crash. The ultimate fix is in cpufreq
to deal with incorrect values, but this patch improves the error
recovery in the AMD powernowk8 driver.

The failure that was reported was as follows:

powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3700+ (1 cpu cores) (version 2.20.00)
powernow-k8: fid 0x2 (1000 MHz), vid 0x12
powernow-k8: fid 0xa (1800 MHz), vid 0xa
powernow-k8: fid 0xc (2000 MHz), vid 0x8
powernow-k8: fid 0xe (2200 MHz), vid 0x8
Marking TSC unstable due to cpufreq changes
powernow-k8: fid trans failed, fid 0x2, curr 0x0
BUG: unable to handle kernel paging request at ffff880807e07b78
IP: [<ffffffff81479163>] cpufreq_stats_update+0x46/0x5b
...

And transition fails and data->currfid ends up with 0. Since
the machine does not support 800Mhz value when the calculation is
done ('find_khz_freq_from_fid(data->currfid);') it reports the
new frequency as 800000 which is bogus. This patch fixes
the issue during target setting.

The patch however does not fix the issue in 'powernowk8_cpu_init'
where the pol->cur can also be set with the 800000 value:

          pol->cur = find_khz_freq_from_fid(data->currfid);
  dprintk("policy current frequency %d kHz\n", pol->cur);

  /* min/max the cpu is capable of */
  if (cpufreq_frequency_table_cpuinfo(pol, data->powernow_table)) {

The fix for that looks to update cpufreq_frequency_table_cpuinfo to
check pol->cur.... but that would cause an regression in how the
acpi-cpufreq driver works (it sets cpu->cur after calling
cpufreq_frequency_table_cpuinfo). Instead the fix will be to let
cpufreq gracefully handle bogus data (another patch).
Acked-by: Borislav Petkov <bp@alien8.de>
CC: andre.przywara@amd.com
CC: Mark.Langsdorf@amd.com
Reported-by: Tobias Diedrich <ranma+xen@tdiedrich.de>
Tested-by: Tobias Diedrich <ranma+xen@tdiedrich.de>
[v1: Rebased on v3.0-rc2, reduced patch to deal with vid case]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Dave Jones <davej@redhat.com>

If the driver submitted an non-existing pol>cur value (say it
used the default initialized value of zero), when the cpufreq
stats tries to setup its initial values it incorrectly sets
stat->last_index to -1 (or 0xfffff...). And cpufreq_stats_update
tries to update at that index location and fails.

This can be caused by:

stat->last_index = freq_table_get_index(stat, policy->cur);

not finding the appropiate frequency in the table (b/c the policy->cur
is wrong) and we end up crashing. The fix however is
concentrated in the 'cpufreq_stats_update' as the last_index
(and old_index) are updated there. Which means it can reset
the last_index to -1 again and on the next iteration cause a crash.

Without this patch, the following crash is observed:

powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3700+ (1 cpu cores) (version 2.20.00)
powernow-k8: fid 0x2 (1000 MHz), vid 0x12
powernow-k8: fid 0xa (1800 MHz), vid 0xa
powernow-k8: fid 0xc (2000 MHz), vid 0x8
powernow-k8: fid 0xe (2200 MHz), vid 0x8
Marking TSC unstable due to cpufreq changes
powernow-k8: fid trans failed, fid 0x2, curr 0x0
BUG: unable to handle kernel paging request at ffff880807e07b78
IP: [<ffffffff81479163>] cpufreq_stats_update+0x46/0x5b
.. snip..
Pid: 1, comm: swapper Not tainted 3.0.0-rc2 #45 MICRO-STAR INTERNATIONAL CO., LTD MS-7094/MS-7094
..snip..
Call Trace:
 [<ffffffff81479248>] cpufreq_stat_notifier_trans+0x48/0x7c
 [<ffffffff81095d68>] notifier_call_chain+0x32/0x5e
 [<ffffffff81095e6b>] __srcu_notifier_call_chain+0x47/0x63
 [<ffffffff81095e96>] srcu_notifier_call_chain+0xf/0x11
 [<ffffffff81477e7a>] cpufreq_notify_transition+0x111/0x134
 [<ffffffff8147b0d4>] powernowk8_target+0x53b/0x617
 [<ffffffff8147723a>] __cpufreq_driver_target+0x2e/0x30
 [<ffffffff8147a127>] cpufreq_governor_dbs+0x339/0x356
 [<ffffffff81477394>] __cpufreq_governor+0xa8/0xe9
 [<ffffffff81477525>] __cpufreq_set_policy+0x132/0x13e
 [<ffffffff8147848d>] cpufreq_add_dev_interface+0x272/0x28c
Reported-by: Tobias Diedrich <ranma+xen@tdiedrich.de>
Tested-by: Tobias Diedrich <ranma+xen@tdiedrich.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Dave Jones <davej@redhat.com>

Fixed remaining issues of the signedness bug discovered by Dan Carpenter.
A check was remaining that tests if unsigned rt->rate is >= 0.
Changed that so that rt->rate now consistently uses ARRAY_SIZE(rates)
as invalid rate value and not -1.
Signed-off-by: Torsten Schenk <torsten.schenk@zoho.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
  kbuild: Call depmod.sh via shell
  perf: clear out make flags when calling kernel make kernelver

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  AFS: Use i_generation not i_version for the vnode uniquifier
  AFS: Set s_id in the superblock to the volume name
  vfs: Fix data corruption after failed write in __block_write_begin()
  afs: afs_fill_page reads too much, or wrong data
  VFS: Fix vfsmount overput on simultaneous automount
  fix wrong iput on d_inode introduced by e6bc45d6
  Delay struct net freeing while there's a sysfs instance refering to it
  afs: fix sget() races, close leak on umount
  ubifs: fix sget races
  ubifs: split allocation of ubifs_info into a separate function
  fix leak in proc_set_super()

* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-3.x:
  sh: sh7724: Add USBHS DMAEngine support
  sh: ecovec: Add renesas_usbhs support
  sh, exec: remove redundant set_fs(USER_DS)
  drivers: sh: resume enabled clocks fix
  dmaengine: shdma: SH_DMAC_MAX_CHANNELS message fix
  sh: Fix up xchg/cmpxchg corruption with gUSA RB.
  sh: Remove compressed kernel libgcc dependency.
  sh: fix wrong icache/dcache address-array start addr in cache-debugfs.