- 15 Sep, 2024 1 commit
-
-
Maxime Chevallier authored
Some platforms that use fs_enet don't have the PER register clock. This optional dependency on the clock was incorrectly made mandatory when switching to devm_ accessors. Reported-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Closes: https://lore.kernel.org/netdev/4e4defa9-ef2f-4ff1-95ca-6627c24db20c@wanadoo.fr/ Fixes: c614acf6 ("net: ethernet: fs_enet: simplify clock handling with devm accessors") Signed-off-by:
Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by:
Jakub Kicinski <kuba@kernel.org>
-
- 14 Sep, 2024 39 commits
-
-
Jakub Kicinski authored
MD Danish Anwar says: ==================== Introduce HSR offload support for ICSSG This series introduces HSR offload support for ICSSG driver. To support HSR offload to hardware, ICSSG HSR firmware is used. This series introduces, 1. HSR frame offload support for ICSSG driver. 2. HSR Tx Packet duplication offload 3. HSR Tx Tag and Rx Tag offload 4. Multicast filtering support in HSR offload mode. 5. Dependencies related to IEP. HSR Test Setup: -------------- ___________ ___________ ___________ | | Link AB | | Link BC | | __| AM64* |_________| AM64 |_________| AM64* |___ | | Station A | | Station B | | Station C | | | |___________| |___________| |___________| | | | |______________________________________________________________| Link CA *Could be any device that supports two ethernet interfaces. Steps to switch to HSR frame forward offload mode: ------------------------------------------------- Example assuming eth1, eth2 ports of ICSSG1 on AM64-EVM 1) Enable HSR offload for both interfaces ethtool -K eth1 hsr-fwd-offload on ethtool -K eth1 hsr-dup-offload on ethtool -K eth1 hsr-tag-ins-offload on ethtool -K eth1 hsr-tag-rm-offload on ethtool -K eth2 hsr-fwd-offload on ethtool -K eth2 hsr-dup-offload on ethtool -K eth2 hsr-tag-ins-offload on ethtool -K eth2 hsr-tag-rm-offload on 2) Create HSR interface and add slave interfaces to it ip link add name hsr0 type hsr slave1 eth1 slave2 eth2 \ supervision 45 version 1 3) Add IP address to the HSR interface ip addr add <IP_ADDR>/24 dev hsr0 4) Bring up the HSR interface ip link set hsr0 up Switching back to previous mode: -------------------------------- 1) Delete HSR interface ip link delete hsr0 2) Disable HSR port-to-port offloading mode, packet duplication ethtool -K eth1 hsr-fwd-offload off ethtool -K eth1 hsr-dup-offload off ethtool -K eth1 hsr-tag-ins-offload off ethtool -K eth1 hsr-tag-rm-offload off ethtool -K eth2 hsr-fwd-offload off ethtool -K eth2 hsr-dup-offload off ethtool -K eth2 hsr-tag-ins-offload off ethtool -K eth2 hsr-tag-rm-offload off Testing the port-to-port frame forward offload feature: ----------------------------------------------------- 1) Connect the LAN cables as shown in the test setup. 2) Configure Station A and Station C in HSR non-offload mode. 3) Configure Station B is HSR offload mode. 4) Since HSR is a redundancy protocol, disconnect cable "Link CA", to ensure frames from Station A reach Station C only through Station B. 5) Run iperf3 Server on Station C and client on station A. 7) Check the CPU usage on Station B. CPU usage report on Station B using mpstat when running UDP iperf3: ------------------------------------------------------------------- 1) Non-Offload case ------------------- CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle all 0.00 0.00 0.50 0.00 3.52 29.15 0.00 0.00 66.83 0 0.00 0.00 0.00 0.00 7.00 58.00 0.00 0.00 35.00 1 0.00 0.00 0.99 0.00 0.99 0.00 0.00 0.00 98.02 2) Offload case --------------- CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle all 0.00 0.00 0.00 0.00 0.50 0.00 0.00 0.00 99.50 0 0.00 0.00 0.99 0.00 0.00 0.00 0.00 0.00 99.01 1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 Note: 1) At the very least, hsr-fwd-offload must be enabled. Without offloading the port-to-port offload, other HSR offloads cannot be enabled. 2) hsr-tag-ins-offload and hsr-dup-offload are tightly coupled in the firmware implementation. They both need to be enabled / disabled together. v1: https://lore.kernel.org/20240808110800.1281716-1-danishanwar@ti.com/ v2: https://lore.kernel.org/20240813074233.2473876-1-danishanwar@ti.com v3: https://lore.kernel.org/20240828091901.3120935-1-danishanwar@ti.com/ v4: https://lore.kernel.org/20240904100506.3665892-1-danishanwar@ti.com/ v5: https://lore.kernel.org/20240906111538.1259418-1-danishanwar@ti.com/ [0] https://lore.kernel.org/202409061658.vSwcFJiK-lkp@intel.com/ [1] https://lore.kernel.org/20240828091901.3120935-5-danishanwar@ti.com/ [2] https://lore.kernel.org/20240828091901.3120935-7-danishanwar@ti.com/ [3] https://lore.kernel.org/20240813074233.2473876-2-danishanwar@ti.com/ [4] https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=e846be0fba85 ==================== Link: https://patch.msgid.link/20240911081603.2521729-1-danishanwar@ti.comSigned-off-by: -
MD Danish Anwar authored
Add support for multicast filtering in HSR mode Reviewed-by:
Roger Quadros <rogerq@kernel.org> Signed-off-by:
MD Danish Anwar <danishanwar@ti.com> Link: https://patch.msgid.link/20240911081603.2521729-6-danishanwar@ti.comSigned-off-by:
-
Ravi Gunasekaran authored
The HSR stack allows to offload its Tx packet duplication functionality to the hardware. Enable this offloading feature for ICSSG driver. Add support to offload HSR Tx Tag Insertion and Rx Tag Removal and duplicate discard. hsr tag insertion offload and hsr dup offload are tightly coupled in firmware implementation. Both these features need to be enabled / disabled together. Duplicate discard is done as part of RX tag removal and it is done by the firmware. When driver sends the r30 command ICSSG_EMAC_HSR_RX_OFFLOAD_ENABLE, firmware does RX tag removal as well as duplicate discard. Signed-off-by:
Ravi Gunasekaran <r-gunasekaran@ti.com> Signed-off-by:
-
MD Danish Anwar authored
Add support for offloading HSR port-to-port frame forward to hardware. When the slave interfaces are added to the HSR interface, the PRU cores will be stopped and ICSSG HSR firmwares will be loaded to them. Similarly, when HSR interface is deleted, the PRU cores will be restarted and the last used firmwares will be reloaded. PRUeth interfaces will be back to the last used mode. This commit also renames some APIs that are common between switch and hsr mode with '_fw_offload' suffix. Signed-off-by:
-
MD Danish Anwar authored
The def_inc is stored in icss_iep structure. Currently default increment (ns per clock tick) is hardcoded to 4 (Clock frequency being 250 MHz). Change this to use the iep->def_inc variable as the iep structure is now accessible to the driver files. Reviewed-by:
-
MD Danish Anwar authored
Move icss_iep structure definition and to icss_iep.h file so that the structure members can be used / accessed by all icssg driver files. Reviewed-by:
Simon Horman <horms@kernel.org> Reviewed-by:
Jacob Keller <jacob.e.keller@intel.com> Reviewed-by:
-
Jakub Kicinski authored
Rosen Penev says: ==================== net: ibm: emac: modernize a bit ==================== Link: https://patch.msgid.link/20240912024903.6201-1-rosenp@gmail.comSigned-off-by:
-
Rosen Penev authored
This is completely unused. Signed-off-by:
Rosen Penev <rosenp@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20240912024903.6201-10-rosenp@gmail.comSigned-off-by:
-
Rosen Penev authored
EPROBE_DEFER, which probably wasn't available when this driver was written, can be used instead of waiting manually. Signed-off-by:
-
Rosen Penev authored
of_property_read_u32 can be used. Signed-off-by:
-
Rosen Penev authored
Avoids having to use own struct member. Signed-off-by:
-
Rosen Penev authored
Cleans it up automatically. No need to handle manually. Signed-off-by:
-
Rosen Penev authored
Switching to devm management of mii_bus allows to remove mdiobus_unregister calls and thus avoids needing a mii_bus global struct member. Signed-off-by:
-
Rosen Penev authored
Allows removing manual iounmap. Signed-off-by:
-
Rosen Penev authored
It's the last to go in remove. Safe to let devm handle it. Also move request_irq to probe for clarity. It's removed in _remove not close. Use dev_err_probe instead of printk. Handles EPROBE_DEFER automatically. Signed-off-by:
-
Rosen Penev authored
Allows to simplify the code slightly. This is safe to do as free_netdev gets called last. Signed-off-by:
-
Linu Cherian authored
Display channel info in the RPM map debugfs output. With this, cat /sys/kernel/debug/cn10k/rvu_pf_rpm_map would display channel number for each device in addition to the existing data. Sample output: PCI dev RVU PF Func NIX block rpm LMAC CHAN 0002:02:00.0 0x400 NIX0 rpm0 LMAC0 256 Signed-off-by:
Linu Cherian <lcherian@marvell.com> Link: https://patch.msgid.link/20240912161450.164402-3-lcherian@marvell.comSigned-off-by:
-
Maxime Chevallier authored
The context info allows continuing DUMP requests, shall they fill the netlink buffer. In the case of filtered DUMP requests, a reference on the netdev is grabbed in the .start() callback and release in .done(). Unfiltered DUMP request don't need the dev pointer to be set in the context info, doing so will trigger an unwanted netdev_put() in .done(). Reported-by: syzbot+e9ed4e4368d450c8f9db@syzkaller.appspotmail.com Closes: https://lore.kernel.org/netdev/000000000000d3bf150621d361a7@google.com/ Fixes: 17194be4 ("net: ethtool: Introduce a command to list PHYs on an interface") Signed-off-by:
Vadim Fedorenko <vadim.fedorenko@linux.dev> Link: https://patch.msgid.link/20240913100515.167341-1-maxime.chevallier@bootlin.comSigned-off-by:
-
Jakub Kicinski authored
Merge tag 'linux-can-next-for-6.12-20240911' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next Marc Kleine-Budde says: ==================== pull-request: can-next 2024-09-11 The first patch is by Uwe Kleine-König targets all CAN platform driver and switches back the remove function to struct platform_driver::remove(). A patch by Stefan Mätje fixes the help text of the ESD USB driver. Jake Hamby's patch masks an unneeded interrupt in the m_can driver. The last 2 patches target the rockchip_canfd driver. Arnd Bergmann's patch reworks the delay calculation for the timekeeping worker, a patch by me fixes the decoding of the error code register. * tag 'linux-can-next-for-6.12-20240911' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: can: rockchip_canfd: rkcanfd_handle_error_int_reg_ec(): fix decoding of error code register can: rockchip_canfd: rkcanfd_timestamp_init(): rework delay calculation can: m_can: m_can_chip_config(): mask timestamp wraparound IRQ can: usb: Kconfig: Fix list of devices for esd_usb driver can: Switch back to struct platform_driver::remove() ==================== Link: https://patch.msgid.link/20240912080438.2826895-1-mkl@pengutronix.deSigned-off-by:
-
Dan Carpenter authored
Return an error if dma_set_mask_and_coherent() fails. Don't return success. Fixes: a36e9f5c ("rtase: Add support for a pci table in this module") Signed-off-by:
Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by:
-
Gaosheng Cui authored
Most of the drivers which used this header have been deleted, most of these code is obsoleted, move the only defines that are actually used into arch/powerpc/platforms/chrp/pegasos_eth.c and delete the file completely. Signed-off-by:
Gaosheng Cui <cuigaosheng1@huawei.com> Link: https://patch.msgid.link/20240912011949.2726928-1-cuigaosheng1@huawei.comSigned-off-by:
-
Jakub Kicinski authored
Nelson Escobar says: ==================== enic: Report per queue stats Patch #1: Use a macro instead of static const variables for array sizes. I didn't want to add more static const variables in the next patch so clean up the existing ones first. Patch #2: Collect per queue statistics Patch #3: Report per queue stats in netdev qstats Patch #4: Report some per queue stats in ethtool # NETIF="eno6" tools/testing/selftests/drivers/net/stats.py KTAP version 1 1..5 ok 1 stats.check_pause # XFAIL pause not supported by the device ok 2 stats.check_fec # XFAIL FEC not supported by the device ok 3 stats.pkt_byte_sum ok 4 stats.qstat_by_ifindex ok 5 stats.check_down # tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \ --dump qstats-get --json '{"ifindex": "34"}' [{'ifindex': 34, 'rx-bytes': 66762680, 'rx-csum-unnecessary': 1009345, 'rx-hw-drop-overruns': 0, 'rx-hw-drops': 0, 'rx-packets': 1009673, 'tx-bytes': 137936674899, 'tx-csum-none': 125, 'tx-hw-gso-packets': 2408712, 'tx-needs-csum': 2431531, 'tx-packets': 15475466, 'tx-stop': 0, 'tx-wake': 0}] v2: https://lore.kernel.org/20240905010900.24152-1-neescoba@cisco.com v1: https://lore.kernel.org/20240823235401.29996-1-neescoba@cisco.com ==================== Link: https://patch.msgid.link/20240912005039.10797-1-neescoba@cisco.comSigned-off-by: -
Nelson Escobar authored
Make 'ethtool -S <intf>' output show some per rq/wq statistics that don't exist in the netdev qstats. Signed-off-by:
Nelson Escobar <neescoba@cisco.com> Signed-off-by:
John Daley <johndale@cisco.com> Signed-off-by:
Satish Kharat <satishkh@cisco.com> Link: https://patch.msgid.link/20240912005039.10797-5-neescoba@cisco.comSigned-off-by:
-
Nelson Escobar authored
Report per queue wq/rq statistics in netdev qstats. Signed-off-by:
-
Nelson Escobar authored
Collect and per rq/wq statistics. Signed-off-by:
-
Nelson Escobar authored
In enic_ethtool.c there is no need to use static const variables to store array sizes when a macro can be used instead. Signed-off-by:
-
Jakub Kicinski authored
Ido Schimmel says: ==================== net: fib_rules: Add DSCP selector support Currently, the kernel rejects IPv4 FIB rules that try to match on the upper three DSCP bits: # ip -4 rule add tos 0x1c table 100 # ip -4 rule add tos 0x3c table 100 Error: Invalid tos. The reason for that is that historically users of the FIB lookup API only populated the lower three DSCP bits in the TOS field of the IPv4 flow key ('flowi4_tos'), which fits the TOS definition from the initial IPv4 specification (RFC 791). This is not very useful nowadays and instead some users want to be able to match on the six bits DSCP field, which replaced the TOS and IP precedence fields over 25 years ago (RFC 2474). In addition, the current behavior differs between IPv4 and IPv6 which does allow users to match on the entire DSCP field using the TOS selector. Recent patchsets made sure that callers of the FIB lookup API now populate the entire DSCP field in the IPv4 flow key. Therefore, it is now possible to extend FIB rules to match on DSCP. This is done by adding a new DSCP attribute which is implemented for both IPv4 and IPv6 to provide user space programs a consistent behavior between both address families. The behavior of the old TOS selector is unchanged and IPv4 FIB rules using it will only match on the lower three DSCP bits. The kernel will reject rules that try to use both selectors. Patch #1 adds the new DSCP attribute but rejects its usage. Patches #2-#3 implement IPv4 and IPv6 support. Patch #4 allows user space to use the new attribute. Patches #5-#6 add selftests. ==================== Link: https://patch.msgid.link/20240911093748.3662015-1-idosch@nvidia.comSigned-off-by: -
Ido Schimmel authored
Test that locally generated traffic from a socket that specifies a DS Field using the IP_TOS / IPV6_TCLASS socket options is correctly redirected using a FIB rule that matches on DSCP. Add negative tests to verify that the rule is not it when it should not. Test with both IPv4 and IPv6 and with both TCP and UDP sockets. Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Reviewed-by:
Guillaume Nault <gnault@redhat.com> Reviewed-by:
David Ahern <dsahern@kernel.org> Link: https://patch.msgid.link/20240911093748.3662015-7-idosch@nvidia.comSigned-off-by:
-
Ido Schimmel authored
Add tests for the new FIB rule DSCP selector. Test with both IPv4 and IPv6 and with both input and output routes. Signed-off-by:
-
Ido Schimmel authored
Now that both IPv4 and IPv6 support the new DSCP selector, enable user space to configure FIB rules that make use of it by changing the policy of the new DSCP attribute so that it accepts values in the range of [0, 63]. Use NLA_U8 rather than NLA_UINT as the field is of fixed size. Signed-off-by:
-
Ido Schimmel authored
Implement support for the new DSCP selector that allows IPv6 FIB rules to match on the entire DSCP field. This is done despite the fact that the above can be achieved using the existing TOS selector, so that user space program will be able to work with IPv4 and IPv6 rules in the same way. Differentiate between both selectors by adding a new bit in the IPv6 FIB rule structure that is only set when the 'FRA_DSCP' attribute is specified by user space. Reject rules that use both selectors. Signed-off-by:
-
Ido Schimmel authored
Implement support for the new DSCP selector that allows IPv4 FIB rules to match on the entire DSCP field, unlike the existing TOS selector that only matches on the three lower DSCP bits. Differentiate between both selectors by adding a new bit in the IPv4 FIB rule structure (in an existing one byte hole) that is only set when the 'FRA_DSCP' attribute is specified by user space. Reject rules that use both selectors. Signed-off-by:
-
Ido Schimmel authored
The FIB rule TOS selector is implemented differently between IPv4 and IPv6. In IPv4 it is used to match on the three "Type of Services" bits specified in RFC 791, while in IPv6 is it is used to match on the six DSCP bits specified in RFC 2474. Add a new FIB rule attribute to allow matching on DSCP. The attribute will be used to implement a 'dscp' selector in ip-rule with a consistent behavior between IPv4 and IPv6. For now, set the type of the attribute to 'NLA_REJECT' so that user space will not be able to configure it. This restriction will be lifted once both IPv4 and IPv6 support the new attribute. Signed-off-by:
-
Danielle Ratson authored
During the firmware flashing process, notifications are sent to user space to provide progress updates. When an error occurs, an error message is sent to indicate what went wrong. In some cases, appropriate error messages are missing. Add relevant error messages where applicable, allowing user space to better understand the issues encountered. Signed-off-by:
Danielle Ratson <danieller@nvidia.com> Reviewed-by:
Petr Machata <petrm@nvidia.com> Reviewed-by:
-
Andy Shevchenko authored
The PCI vendor ID for Cadence is defined in pci_ids.h. Use it. While at it, move to PCI_VDEVICE() macro and usual pattern for PCI device ID. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://patch.msgid.link/20240913125146.3628751-1-andriy.shevchenko@linux.intel.comSigned-off-by:
-
Martyn Welch authored
The enetc driver uses ifdefs when checking whether CONFIG_FSL_ENETC_PTP_CLOCK is enabled in a number of places. This works if the driver is built-in but fails if the driver is available as a kernel module. Replace the instances of ifdef with use of the IS_ENABLED macro, that will evaluate as true when this feature is built as a kernel module and follows the kernel's coding style. Reviewed-by:
Martyn Welch <martyn.welch@collabora.com> Reviewed-by:
-
Kory Maincent authored
Fix a missing end of phrase in the documentation. It describes the ETHTOOL_A_C33_PSE_ACTUAL_PW attribute, which was not fully explained. Also, fix grammar issues by using simple present tense instead of present continuous. Reviewed-by:
Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by:
Kory Maincent <kory.maincent@bootlin.com> Reviewed-by:
-
Qianqiang Liu authored
The "err" is always zero, so the following branch can never be executed: if (err) { ndev->stats.rx_dropped++; kfree_skb(skb); } Therefore, the "if" statement can be removed. Use "ndev->stats.rx_errors" to count "napi_build_skb()" failure Reviewed-by:Qianqiang Liu <qianqiang.liu@163.com> Link: https://patch.msgid.link/20240913014731.149739-1-qianqiang.liu@163.comSigned-off-by:
-
Jakub Kicinski authored
Merge tag 'for-net-next-2024-09-12' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next Luiz Augusto von Dentz says: ==================== bluetooth-next pull request for net-next: - btusb: Add MediaTek MT7925-B22M support ID 0x13d3:0x3604 - btusb: Add Realtek RTL8852C support ID 0x0489:0xe122 - btrtl: Add the support for RTL8922A - btusb: Add 2 USB HW IDs for MT7925 (0xe118/e) - btnxpuart: Add support for ISO packets - btusb: Add Mediatek MT7925 support ID 0x13d3:0x3608 - btsdio: Do not bind to non-removable CYW4373 - hci_uart: Add support for Amlogic HCI UART * tag 'for-net-next-2024-09-12' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next: (27 commits) Bluetooth: btintel_pcie: Allocate memory for driver private data Bluetooth: btusb: Fix not handling ZPL/short-transfer Bluetooth: btusb: Add 2 USB HW IDs for MT7925 (0xe118/e) Bluetooth: btsdio: Do not bind to non-removable CYW4373 Bluetooth: hci_sync: Ignore errors from HCI_OP_REMOTE_NAME_REQ_CANCEL Bluetooth: CMTP: Mark BT_CMTP as DEPRECATED Bluetooth: replace deprecated strncpy with strscpy_pad Bluetooth: hci_core: Fix sending MGMT_EV_CONNECT_FAILED Bluetooth: btrtl: Set msft ext address filter quirk for RTL8852B Bluetooth: Use led_set_brightness() in LED trigger activate() callback Bluetooth: btrtl: Use kvmemdup to simplify the code Bluetooth: btusb: Add Mediatek MT7925 support ID 0x13d3:0x3608 Bluetooth: btrtl: Add the support for RTL8922A Bluetooth: hci_ldisc: Use speed set by btattach as oper_speed Bluetooth: hci_conn: Remove redundant memset after kzalloc Bluetooth: L2CAP: Remove unused declarations dt-bindings: bluetooth: bring the HW description closer to reality for wcn6855 Bluetooth: btnxpuart: Add support for ISO packets Bluetooth: hci_h4: Add support for ISO packets in h4_recv.h Bluetooth: btusb: Add Realtek RTL8852C support ID 0x0489:0xe122 ... ==================== Link: https://patch.msgid.link/20240912214317.3054060-1-luiz.dentz@gmail.comSigned-off-by:
-
