- 12 Aug, 2024 9 commits
-
-
Frank Li authored
Add missed property phys, which indicate how connect to serdes phy. Fix below warning: arch/arm64/boot/dts/freescale/fsl-lx2160a-honeycomb.dtb: fsl-mc@80c000000: dpmacs:ethernet@7: Unevaluated properties are not allowed ('phys' was unexpected) Signed-off-by:Frank Li <Frank.Li@nxp.com> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Pawel Dembicki says: ==================== net: dsa: vsc73xx: fix MDIO bus access and PHY opera This series are extracted patches from net-next series [0]. The VSC73xx driver has issues with PHY configuration. This patch series fixes most of them. The first patch synchronizes the register configuration routine with the datasheet recommendations. Patches 2-3 restore proper communication on the MDIO bus. Currently, the write value isn't sent to the MDIO register, and without a busy check, communication with the PHY can be interrupted. This causes the PHY to receive improper configuration and autonegotiation could fail. The fourth patch removes the PHY reset blockade, as it is no longer required. After fixing the MDIO operations, autonegotiation became possible. The last patch removes the blockade, which became unnecessary after the MDIO operations fix. [0] https://patchwork.kernel.org/project/netdevbpf/list/?series=874739&state=%2A&archive=both ==================== Signed-off-by:
-
Pawel Dembicki authored
When the vsc73xx mdio bus work properly, the generic autonegotiation configuration works well. Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by:
-
Pawel Dembicki authored
Resetting the VSC73xx PHY was problematic because the MDIO bus, without a busy check, read and wrote incorrect register values. My investigation indicates that resetting the PHY only triggers changes in configuration. However, improper register values written earlier were only exposed after a soft reset. The reset itself wasn't the issue; rather, the problem stemmed from incorrect read and write operations. A 'soft_reset' can now proceed normally. There are no reasons to keep the VSC73xx from being reset. This commit removes the reset blockade in the 'vsc73xx_phy_write' function. Reviewed-by:
Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by:
-
Pawel Dembicki authored
The VSC73xx has a busy flag used during MDIO operations. It is raised when MDIO read/write operations are in progress. Without it, PHYs are misconfigured and bus operations do not work as expected. Fixes: 05bd97fc ("net: dsa: Add Vitesse VSC73xx DSA router driver") Reviewed-by:
-
Pawel Dembicki authored
In the 'vsc73xx_phy_write' function, the register value is missing, and the phy write operation always sends zeros. This commit passes the value variable into the proper register. Fixes: 05bd97fc ("net: dsa: Add Vitesse VSC73xx DSA router driver") Reviewed-by:
-
Pawel Dembicki authored
According to the datasheet description ("Port Mode Procedure" in 5.6.2), the VSC73XX_MAC_CFG_WEXC_DIS bit is configured only for half duplex mode. The WEXC_DIS bit is responsible for MAC behavior after an excessive collision. Let's set it as described in the datasheet. Fixes: 05bd97fc ("net: dsa: Add Vitesse VSC73xx DSA router driver") Reviewed-by: -
Radhey Shyam Pandey authored
In axiethernet header fix register defines comment description to be inline with IP documentation. It updates MAC configuration register, MDIO configuration register and frame filter control description. Fixes: 8a3b7a25 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by:
Radhey Shyam Pandey <radhey.shyam.pandey@amd.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Dan Carpenter authored
We can't dereference "skb" after calling vcc->push() because the skb is released. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by:
-
- 11 Aug, 2024 2 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-qDavid S. Miller authored
ueue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-08-07 (igc) This series contains updates to igc driver only. Faizal adjusts the size of the MAC internal buffer on i226 devices to resolve an errata for leaking packet transmits. He also corrects a condition in which qbv_config_change_errors are incorrectly counted. Lastly, he adjusts the conditions for resetting the adapter when changing TSN Tx mode and corrects the conditions in which gtxoffset register is set. ==================== Signed-off-by: -
Moon Yeounsu authored
`ip_hdr(skb)->ihl << 2` is the same as `ip_hdrlen(skb)` Therefore, we should use a well-defined function not a bit shift to find the header length. It also compresses two lines to a single line. Signed-off-by:
Moon Yeounsu <yyyynoom@gmail.com> Reviewed-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
- 10 Aug, 2024 11 commits
-
-
Jakub Kicinski authored
Tariq Toukan says: ==================== mlx5 misc fixes 2024-08-08 This patchset provides misc bug fixes from the team to the mlx5 core and Eth drivers. ==================== Link: https://patch.msgid.link/20240808144107.2095424-1-tariqt@nvidia.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Gal Pressman authored
The queue stats API queries the queues according to the real_num_[tr]x_queues, in case the device is down and channels were not yet created, don't try to query their statistics. To trigger the panic, run this command before the interface is brought up: ./cli.py --spec ../../../Documentation/netlink/specs/netdev.yaml --dump qstats-get --json '{"ifindex": 4}' BUG: kernel NULL pointer dereference, address: 0000000000000c00 PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP PTI CPU: 3 UID: 0 PID: 977 Comm: python3 Not tainted 6.10.0+ #40 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:mlx5e_get_queue_stats_rx+0x3c/0xb0 [mlx5_core] Code: fc 55 48 63 ee 53 48 89 d3 e8 40 3d 70 e1 85 c0 74 58 4c 89 ef e8 d4 07 04 00 84 c0 75 41 49 8b 84 24 f8 39 00 00 48 8b 04 e8 <48> 8b 90 00 0c 00 00 48 03 90 40 0a 00 00 48 89 53 08 48 8b 90 08 RSP: 0018:ffff888116be37d0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff888116be3868 RCX: 0000000000000004 RDX: ffff88810ada4000 RSI: 0000000000000000 RDI: ffff888109df09c0 RBP: 0000000000000000 R08: 0000000000000004 R09: 0000000000000004 R10: ffff88813461901c R11: ffffffffffffffff R12: ffff888109df0000 R13: ffff888109df09c0 R14: ffff888116be38d0 R15: 0000000000000000 FS: 00007f4375d5c740(0000) GS:ffff88852c980000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000c00 CR3: 0000000106ada006 CR4: 0000000000370eb0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? __die+0x1f/0x60 ? page_fault_oops+0x14e/0x3d0 ? exc_page_fault+0x73/0x130 ? asm_exc_page_fault+0x22/0x30 ? mlx5e_get_queue_stats_rx+0x3c/0xb0 [mlx5_core] netdev_nl_stats_by_netdev+0x2a6/0x4c0 ? __rmqueue_pcplist+0x351/0x6f0 netdev_nl_qstats_get_dumpit+0xc4/0x1b0 genl_dumpit+0x2d/0x80 netlink_dump+0x199/0x410 __netlink_dump_start+0x1aa/0x2c0 genl_family_rcv_msg_dumpit+0x94/0xf0 ? __pfx_genl_start+0x10/0x10 ? __pfx_genl_dumpit+0x10/0x10 ? __pfx_genl_done+0x10/0x10 genl_rcv_msg+0x116/0x2b0 ? __pfx_netdev_nl_qstats_get_dumpit+0x10/0x10 ? __pfx_genl_rcv_msg+0x10/0x10 netlink_rcv_skb+0x54/0x100 genl_rcv+0x24/0x40 netlink_unicast+0x21a/0x340 netlink_sendmsg+0x1f4/0x440 __sys_sendto+0x1b6/0x1c0 ? do_sock_setsockopt+0xc3/0x180 ? __sys_setsockopt+0x60/0xb0 __x64_sys_sendto+0x20/0x30 do_syscall_64+0x50/0x110 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f43757132b0 Code: c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 1d 45 31 c9 45 31 c0 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 68 c3 0f 1f 80 00 00 00 00 41 54 48 83 ec 20 RSP: 002b:00007ffd258da048 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00007ffd258da0f8 RCX: 00007f43757132b0 RDX: 000000000000001c RSI: 00007f437464b850 RDI: 0000000000000003 RBP: 00007f4375085de0 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: ffffffffc4653600 R14: 0000000000000001 R15: 00007f43751a6147 </TASK> Modules linked in: netconsole xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcgss oid_registry overlay rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm mlx5_ib ib_uverbs ib_core zram zsmalloc mlx5_core fuse [last unloaded: netconsole] CR2: 0000000000000c00 ---[ end trace 0000000000000000 ]--- RIP: 0010:mlx5e_get_queue_stats_rx+0x3c/0xb0 [mlx5_core] Code: fc 55 48 63 ee 53 48 89 d3 e8 40 3d 70 e1 85 c0 74 58 4c 89 ef e8 d4 07 04 00 84 c0 75 41 49 8b 84 24 f8 39 00 00 48 8b 04 e8 <48> 8b 90 00 0c 00 00 48 03 90 40 0a 00 00 48 89 53 08 48 8b 90 08 RSP: 0018:ffff888116be37d0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff888116be3868 RCX: 0000000000000004 RDX: ffff88810ada4000 RSI: 0000000000000000 RDI: ffff888109df09c0 RBP: 0000000000000000 R08: 0000000000000004 R09: 0000000000000004 R10: ffff88813461901c R11: ffffffffffffffff R12: ffff888109df0000 R13: ffff888109df09c0 R14: ffff888116be38d0 R15: 0000000000000000 FS: 00007f4375d5c740(0000) GS:ffff88852c980000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000c00 CR3: 0000000106ada006 CR4: 0000000000370eb0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Fixes: 7b66ae53 ("net/mlx5e: Add per queue netdev-genl stats") Signed-off-by:Gal Pressman <gal@nvidia.com> Signed-off-by:
Tariq Toukan <tariqt@nvidia.com> Reviewed-by:
Joe Damato <jdamato@fastly.com> Link: https://patch.msgid.link/20240808144107.2095424-6-tariqt@nvidia.comSigned-off-by:
-
Cosmin Ratiu authored
Previously, an ethtool rx flow with no attrs would not be added to the NIC as it has no rules to configure the hw with, but it would be reported as successful to the caller (return code 0). This is confusing for the user as ethtool then reports "Added rule $num", but no rule was actually added. This change corrects that by instead reporting these wrong rules as -EINVAL. Fixes: b29c61da ("net/mlx5e: Ethtool steering flow validation refactoring") Signed-off-by:
Cosmin Ratiu <cratiu@nvidia.com> Reviewed-by:
Saeed Mahameed <saeedm@nvidia.com> Reviewed-by:
Dragos Tatulea <dtatulea@nvidia.com> Signed-off-by:
-
Dragos Tatulea authored
mlx5e_safe_reopen_channels() requires the state lock taken. The referenced changed in the Fixes tag removed the lock to fix another issue. This patch adds it back but at a later point (when calling mlx5e_safe_reopen_channels()) to avoid the deadlock referenced in the Fixes tag. Fixes: eab0da38 ("net/mlx5e: Fix possible deadlock on mlx5e_tx_timeout_work") Signed-off-by:
Breno Leitao <leitao@debian.org> Reviewed-by:
Moshe Shemesh <moshe@nvidia.com> Signed-off-by:
-
Dragos Tatulea authored
During latency tests (netperf TCP_RR) a 30% degradation of HW GRO vs SW GRO was observed. This is due to SHAMPO triggering timeout filler CQEs instead of delivering the CQE for the packet. Having a short timeout for SHAMPO doesn't bring any benefits as it is the driver that does the merging, not the hardware. On the contrary, it can have a negative impact: additional filler CQEs are generated due to the timeout. As there is no way to disable this timeout, this change sets it to the maximum value. Instead of using the packet_merge.timeout parameter which is also used for LRO, set the value directly when filling in the rest of the SHAMPO parameters in mlx5e_build_rq_param(). Fixes: 99be5617 ("net/mlx5e: SHAMPO, Re-enable HW-GRO") Signed-off-by:
-
Tariq Toukan authored
Unconditionally calling the MPIR query on BF separate mode yields the FW syndrome below [1]. Do not call it unless admin clearly specified the SD group, i.e. expressing the intention of using the multi-PF netdev feature. This fix covers cases not covered in commit fca3b479 ("net/mlx5: Do not query MPIR on embedded CPU function"). [1] mlx5_cmd_out_err:808:(pid 8267): ACCESS_REG(0x805) op_mod(0x1) failed, status bad system state(0x4), syndrome (0x685f19), err(-5) Fixes: 678eb448 ("net/mlx5: SD, Implement basic query and instantiation") Signed-off-by:
-
Jakub Kicinski authored
Jakub Sitnicki says: ==================== Don't take HW USO path when packets can't be checksummed by device This series addresses a recent regression report from syzbot [1]. After enabling UDP_SEGMENT for egress devices which don't support checksum offload [2], we need to tighten down the checks which let packets take the HW USO path. The fix consists of two parts: 1. don't let devices offer USO without checksum offload, and 2. force software USO fallback in presence of IPv6 extension headers. [1] https://lore.kernel.org/all/000000000000e1609a061d5330ce@google.com/ [2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=10154dbded6d6a2fecaebdfda206609de0f121a9 v3: https://lore.kernel.org/r/20240807-udp-gso-egress-from-tunnel-v3-0-8828d93c5b45@cloudflare.com v2: https://lore.kernel.org/r/20240801-udp-gso-egress-from-tunnel-v2-0-9a2af2f15d8d@cloudflare.com v1: https://lore.kernel.org/r/20240725-udp-gso-egress-from-tunnel-v1-0-5e5530ead524@cloudflare.com ==================== Link: https://patch.msgid.link/20240808-udp-gso-egress-from-tunnel-v4-0-f5c5b4149ab9@cloudflare.comSigned-off-by:
-
Jakub Sitnicki authored
After enabling UDP GSO for devices not offering checksum offload, we have hit a regression where a bad offload warning can be triggered when sending a datagram with IPv6 extension headers. Extend the UDP GSO IPv6 tests to cover this scenario. Reviewed-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
Jakub Sitnicki <jakub@cloudflare.com> Link: https://patch.msgid.link/20240808-udp-gso-egress-from-tunnel-v4-3-f5c5b4149ab9@cloudflare.comSigned-off-by:
-
Jakub Sitnicki authored
In commit 10154dbd ("udp: Allow GSO transmit from devices with no checksum offload") we have intentionally allowed UDP GSO packets marked CHECKSUM_NONE to pass to the GSO stack, so that they can be segmented and checksummed by a software fallback when the egress device lacks these features. What was not taken into consideration is that a CHECKSUM_NONE skb can be handed over to the GSO stack also when the egress device advertises the tx-udp-segmentation / NETIF_F_GSO_UDP_L4 feature. This will happen when there are IPv6 extension headers present, which we check for in __ip6_append_data(). Syzbot has discovered this scenario, producing a warning as below: ip6tnl0: caps=(0x00000006401d7869, 0x00000006401d7869) WARNING: CPU: 0 PID: 5112 at net/core/dev.c:3293 skb_warn_bad_offload+0x166/0x1a0 net/core/dev.c:3291 Modules linked in: CPU: 0 PID: 5112 Comm: syz-executor391 Not tainted 6.10.0-rc7-syzkaller-01603-g80ab5445 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 06/07/2024 RIP: 0010:skb_warn_bad_offload+0x166/0x1a0 net/core/dev.c:3291 [...] Call Trace: <TASK> __skb_gso_segment+0x3be/0x4c0 net/core/gso.c:127 skb_gso_segment include/net/gso.h:83 [inline] validate_xmit_skb+0x585/0x1120 net/core/dev.c:3661 __dev_queue_xmit+0x17a4/0x3e90 net/core/dev.c:4415 neigh_output include/net/neighbour.h:542 [inline] ip6_finish_output2+0xffa/0x1680 net/ipv6/ip6_output.c:137 ip6_finish_output+0x41e/0x810 net/ipv6/ip6_output.c:222 ip6_send_skb+0x112/0x230 net/ipv6/ip6_output.c:1958 udp_v6_send_skb+0xbf5/0x1870 net/ipv6/udp.c:1292 udpv6_sendmsg+0x23b3/0x3270 net/ipv6/udp.c:1588 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0xef/0x270 net/socket.c:745 ____sys_sendmsg+0x525/0x7d0 net/socket.c:2585 ___sys_sendmsg net/socket.c:2639 [inline] __sys_sendmmsg+0x3b2/0x740 net/socket.c:2725 __do_sys_sendmmsg net/socket.c:2754 [inline] __se_sys_sendmmsg net/socket.c:2751 [inline] __x64_sys_sendmmsg+0xa0/0xb0 net/socket.c:2751 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f [...] </TASK> We are hitting the bad offload warning because when an egress device is capable of handling segmentation offload requested by skb_shinfo(skb)->gso_type, the chain of gso_segment callbacks won't produce any segment skbs and return NULL. See the skb_gso_ok() branch in {__udp,tcp,sctp}_gso_segment helpers. To fix it, force a fallback to software USO when processing a packet with IPv6 extension headers, since we don't know if these can checksummed by all devices which offer USO. Fixes: 10154dbd ("udp: Allow GSO transmit from devices with no checksum offload") Reported-by: syzbot+e15b7e15b8a751a91d9a@syzkaller.appspotmail.com Closes: https://lore.kernel.org/all/000000000000e1609a061d5330ce@google.com/Reviewed-by:
-
Jakub Sitnicki authored
UDP segmentation offload inherently depends on checksum offload. It should not be possible to disable checksum offload while leaving USO enabled. Enforce this dependency in code. There is a single tx-udp-segmentation feature flag to indicate support for both IPv4/6, hence the devices wishing to support USO must offer checksum offload for both IP versions. Fixes: 10154dbd ("udp: Allow GSO transmit from devices with no checksum offload") Suggested-by:
Willem de Bruijn <willemdebruijn.kernel@gmail.com> Signed-off-by:
-
Eric Dumazet authored
syzbot/KMSAN reported use of uninit-value in get_dev_xmit() [1] We must make sure the IPv4 or Ipv6 header is pulled in skb->head before accessing fields in them. Use pskb_inet_may_pull() to fix this issue. [1] BUG: KMSAN: uninit-value in ipv6_pdp_find drivers/net/gtp.c:220 [inline] BUG: KMSAN: uninit-value in gtp_build_skb_ip6 drivers/net/gtp.c:1229 [inline] BUG: KMSAN: uninit-value in gtp_dev_xmit+0x1424/0x2540 drivers/net/gtp.c:1281 ipv6_pdp_find drivers/net/gtp.c:220 [inline] gtp_build_skb_ip6 drivers/net/gtp.c:1229 [inline] gtp_dev_xmit+0x1424/0x2540 drivers/net/gtp.c:1281 __netdev_start_xmit include/linux/netdevice.h:4913 [inline] netdev_start_xmit include/linux/netdevice.h:4922 [inline] xmit_one net/core/dev.c:3580 [inline] dev_hard_start_xmit+0x247/0xa20 net/core/dev.c:3596 __dev_queue_xmit+0x358c/0x5610 net/core/dev.c:4423 dev_queue_xmit include/linux/netdevice.h:3105 [inline] packet_xmit+0x9c/0x6c0 net/packet/af_packet.c:276 packet_snd net/packet/af_packet.c:3145 [inline] packet_sendmsg+0x90e3/0xa3a0 net/packet/af_packet.c:3177 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:745 __sys_sendto+0x685/0x830 net/socket.c:2204 __do_sys_sendto net/socket.c:2216 [inline] __se_sys_sendto net/socket.c:2212 [inline] __x64_sys_sendto+0x125/0x1d0 net/socket.c:2212 x64_sys_call+0x3799/0x3c10 arch/x86/include/generated/asm/syscalls_64.h:45 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Uninit was created at: slab_post_alloc_hook mm/slub.c:3994 [inline] slab_alloc_node mm/slub.c:4037 [inline] kmem_cache_alloc_node_noprof+0x6bf/0xb80 mm/slub.c:4080 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:583 __alloc_skb+0x363/0x7b0 net/core/skbuff.c:674 alloc_skb include/linux/skbuff.h:1320 [inline] alloc_skb_with_frags+0xc8/0xbf0 net/core/skbuff.c:6526 sock_alloc_send_pskb+0xa81/0xbf0 net/core/sock.c:2815 packet_alloc_skb net/packet/af_packet.c:2994 [inline] packet_snd net/packet/af_packet.c:3088 [inline] packet_sendmsg+0x749c/0xa3a0 net/packet/af_packet.c:3177 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:745 __sys_sendto+0x685/0x830 net/socket.c:2204 __do_sys_sendto net/socket.c:2216 [inline] __se_sys_sendto net/socket.c:2212 [inline] __x64_sys_sendto+0x125/0x1d0 net/socket.c:2212 x64_sys_call+0x3799/0x3c10 arch/x86/include/generated/asm/syscalls_64.h:45 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f CPU: 0 UID: 0 PID: 7115 Comm: syz.1.515 Not tainted 6.11.0-rc1-syzkaller-00043-g94ede2a3 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 06/27/2024 Fixes: 999cb275 ("gtp: add IPv6 support") Fixes: 459aa660 ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Harald Welte <laforge@gnumonks.org> Reviewed-by:
Pablo Neira Ayuso <pablo@netfilter.org> Link: https://patch.msgid.link/20240808132455.3413916-1-edumazet@google.comSigned-off-by:
-
- 09 Aug, 2024 5 commits
-
-
Foster Snowhill authored
Apart from the standard "configurations", "interfaces" and "alternate interface settings" in USB, iOS devices also have a notion of "modes". In different modes, the device exposes a different set of available configurations. Depending on the iOS version, and depending on the current mode, the length and contents of the carrier state control message differs: * 1 byte (seen on iOS 4.2.1, 8.4): * 03: carrier off (mode 0) * 04: carrier on (mode 0) * 3 bytes (seen on iOS 10.3.4, 15.7.6): * 03 03 03: carrier off (mode 0) * 04 04 03: carrier on (mode 0) * 4 bytes (seen on iOS 16.5, 17.6): * 03 03 03 00: carrier off (mode 0) * 04 03 03 00: carrier off (mode 1) * 06 03 03 00: carrier off (mode 4) * 04 04 03 04: carrier on (mode 0 and 1) * 06 04 03 04: carrier on (mode 4) Before this change, the driver always used the first byte of the response to determine carrier state. From this larger sample, the first byte seems to indicate the number of available USB configurations in the current mode (with the exception of the default mode 0), and in some cases (namely mode 1 and 4) does not correlate with the carrier state. Previous logic erroneously counted `04 03 03 00` as "carrier on" and `06 04 03 04` as "carrier off" on iOS versions that support mode 1 and mode 4 respectively. Only modes 0, 1 and 4 expose the USB Ethernet interfaces necessary for the ipheth driver. Check the second byte of the control message where possible, and fall back to checking the first byte on older iOS versions. Signed-off-by:Foster Snowhill <forst@pen.gy> Tested-by:
Georgi Valkov <gvalkov@gmail.com> Signed-off-by:
-
Foster Snowhill authored
RX callbacks can fail for multiple reasons: * Payload too short * Payload formatted incorrecly (e.g. bad NCM framing) * Lack of memory None of these should cause the driver to seize up. Make such failures non-critical and continue processing further incoming URBs. Signed-off-by:
-
Foster Snowhill authored
On iPhone 15 Pro Max one can observe periodic URBs with no payload on the "bulk in" (RX) endpoint. These don't seem to do anything meaningful. Reproduced on iOS 17.5.1 and 17.6. This behaviour isn't observed on iPhone 11 on the same iOS version. The nature of these zero-length URBs is so far unknown. Drop RX URBs with no payload. Signed-off-by:
-
Foster Snowhill authored
Rx URB length was already checked in ipheth_rcvbulk_callback_legacy() and ipheth_rcvbulk_callback_ncm(), depending on the current mode. The check in ipheth_rcvbulk_callback() was thus mostly a duplicate. The only place in ipheth_rcvbulk_callback() where we care about the URB length is for the initial control frame. These frames are always 4 bytes long. This has been checked as far back as iOS 4.2.1 on iPhone 3G. Remove the extraneous URB length check. For control frames, check for the specific 4-byte length instead. Signed-off-by:
-
Oliver Neukum authored
ipheth_sndbulk_callback() can submit carrier_work as a part of its error handling. That means that the driver must make sure that the work is cancelled after it has made sure that no more URB can terminate with an error condition. Hence the order of actions in ipheth_close() needs to be inverted. Signed-off-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
-
- 08 Aug, 2024 13 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from Jakub Kicinski: "Including fixes from bluetooth. Current release - regressions: - eth: bnxt_en: fix memory out-of-bounds in bnxt_fill_hw_rss_tbl() on older chips Current release - new code bugs: - ethtool: fix off-by-one error / kdoc contradicting the code for max RSS context IDs - Bluetooth: hci_qca: - QCA6390: fix support on non-DT platforms - QCA6390: don't call pwrseq_power_off() twice - fix a NULL-pointer derefence at shutdown - eth: ice: fix incorrect assigns of FEC counters Previous releases - regressions: - mptcp: fix handling endpoints with both 'signal' and 'subflow' flags set - virtio-net: fix changing ring count when vq IRQ coalescing not supported - eth: gve: fix use of netif_carrier_ok() during reconfig / reset Previous releases - always broken: - eth: idpf: fix bugs in queue re-allocation on reconfig / reset - ethtool: fix context creation with no parameters Misc: - linkwatch: use system_unbound_wq to ease RTNL contention" * tag 'net-6.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (41 commits) net: dsa: microchip: disable EEE for KSZ8567/KSZ9567/KSZ9896/KSZ9897. ethtool: Fix context creation with no parameters net: ethtool: fix off-by-one error in max RSS context IDs net: pse-pd: tps23881: include missing bitfield.h header net: fec: Stop PPS on driver remove net: bcmgenet: Properly overlay PHY and MAC Wake-on-LAN capabilities l2tp: fix lockdep splat net: stmmac: dwmac4: fix PCS duplex mode decode idpf: fix UAFs when destroying the queues idpf: fix memleak in vport interrupt configuration idpf: fix memory leaks and crashes while performing a soft reset bnxt_en : Fix memory out-of-bounds in bnxt_fill_hw_rss_tbl() net: dsa: bcm_sf2: Fix a possible memory leak in bcm_sf2_mdio_register() net/smc: add the max value of fallback reason count Bluetooth: hci_sync: avoid dup filtering when passive scanning with adv monitor Bluetooth: l2cap: always unlock channel in l2cap_conless_channel() Bluetooth: hci_qca: fix a NULL-pointer derefence at shutdown Bluetooth: hci_qca: fix QCA6390 support on non-DT platforms Bluetooth: hci_qca: don't call pwrseq_power_off() twice for QCA6390 ice: Fix incorrect assigns of FEC counts ... -
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-traceLinus Torvalds authored
Pull tracing fixes from Steven Rostedt: - Have reading of event format files test if the metadata still exists. When a event is freed, a flag (EVENT_FILE_FL_FREED) in the metadata is set to state that it is to prevent any new references to it from happening while waiting for existing references to close. When the last reference closes, the metadata is freed. But the "format" was missing a check to this flag (along with some other files) that allowed new references to happen, and a use-after-free bug to occur. - Have the trace event meta data use the refcount infrastructure instead of relying on its own atomic counters. - Have tracefs inodes use alloc_inode_sb() for allocation instead of using kmem_cache_alloc() directly. - Have eventfs_create_dir() return an ERR_PTR instead of NULL as the callers expect a real object or an ERR_PTR. - Have release_ei() use call_srcu() and not call_rcu() as all the protection is on SRCU and not RCU. - Fix ftrace_graph_ret_addr() to use the task passed in and not current. - Fix overflow bug in get_free_elt() where the counter can overflow the integer and cause an infinite loop. - Remove unused function ring_buffer_nr_pages() - Have tracefs freeing use the inode RCU infrastructure instead of creating its own. When the kernel had randomize structure fields enabled, the rcu field of the tracefs_inode was overlapping the rcu field of the inode structure, and corrupting it. Instead, use the destroy_inode() callback to do the initial cleanup of the code, and then have free_inode() free it. * tag 'trace-v6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace: tracefs: Use generic inode RCU for synchronizing freeing ring-buffer: Remove unused function ring_buffer_nr_pages() tracing: Fix overflow in get_free_elt() function_graph: Fix the ret_stack used by ftrace_graph_ret_addr() eventfs: Use SRCU for freeing eventfs_inodes eventfs: Don't return NULL in eventfs_create_dir() tracefs: Fix inode allocation tracing: Use refcount for trace_event_file reference counter tracing: Have format file honor EVENT_FILE_FL_FREED
-
git://evilpiepirate.org/bcachefsLinus Torvalds authored
Pull bcachefs fixes from Kent Overstreet: "Assorted little stuff: - lockdep fixup for lockdep_set_notrack_class() - we can now remove a device when using erasure coding without deadlocking, though we still hit other issues - the 'allocator stuck' timeout is now configurable, and messages are ratelimited. The default timeout has been increased from 10 seconds to 30" * tag 'bcachefs-2024-08-08' of git://evilpiepirate.org/bcachefs: bcachefs: Use bch2_wait_on_allocator() in btree node alloc path bcachefs: Make allocator stuck timeout configurable, ratelimit messages bcachefs: Add missing path_traverse() to btree_iter_next_node() bcachefs: ec should not allocate from ro devs bcachefs: Improved allocator debugging for ec bcachefs: Add missing bch2_trans_begin() call bcachefs: Add a comment for bucket helper types bcachefs: Don't rely on implicit unsigned -> signed integer conversion lockdep: Fix lockdep_set_notrack_class() for CONFIG_LOCK_STAT bcachefs: Fix double free of ca->buckets_nouse -
Linus Torvalds authored
Russell King reported that the arm cbc(aes) crypto module hangs when loaded, and Herbert Xu bisected it to commit 9b9879fc ("modules: catch concurrent module loads, treat them as idempotent"), and noted: "So what's happening here is that the first modprobe tries to load a fallback CBC implementation, in doing so it triggers a load of the exact same module due to module aliases. IOW we're loading aes-arm-bs which provides cbc(aes). However, this needs a fallback of cbc(aes) to operate, which is made out of the generic cbc module + any implementation of aes, or ecb(aes). The latter happens to also be provided by aes-arm-cb so that's why it tries to load the same module again" So loading the aes-arm-bs module ends up wanting to recursively load itself, and the recursive load then ends up waiting for the original module load to complete. This is a regression, in that it used to be that we just tried to load the module multiple times, and then as we went on to install it the second time we would instead just error out because the module name already existed. That is actually also exactly what the original "catch concurrent loads" patch did in commit 9828ed3f ("module: error out early on concurrent load of the same module file"), but it turns out that it ends up being racy, in that erroring out before the module has been fully initialized will cause failures in dependent module loading. See commit ac2263b5 (which was the revert of that "error out early") commit for details about why erroring out before the module has been initialized is actually fundamentally racy. Now, for the actual recursive module load (as opposed to just concurrently loading the same module twice), the race is not an issue. At the same time it's hard for the kernel to see that this is recursion, because the module load is always done from a usermode helper, so the recursion is not some simple callchain within the kernel. End result: this is not the real fix, but this at least adds a warning for the situation (admittedly much too late for all the debugging pain that Russell and Herbert went through) and if we can come to a resolution on how to detect the recursion properly, this re-organizes the code to make that easier. Link: https://lore.kernel.org/all/ZrFHLqvFqhzykuYw@shell.armlinux.org.uk/Reported-by:
Russell King <linux@armlinux.org.uk> Debugged-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Linus Torvalds authored
Merge tag 'loongarch-fixes-6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson Pull LoongArch fixes from Huacai Chen: "Enable general EFI poweroff method to make poweroff usable on hardwares which lack ACPI S5, use accessors to page table entries instead of direct dereference to avoid potential problems, and two trivial kvm cleanups" * tag 'loongarch-fixes-6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson: LoongArch: KVM: Remove undefined a6 argument comment for kvm_hypercall() LoongArch: KVM: Remove unnecessary definition of KVM_PRIVATE_MEM_SLOTS LoongArch: Use accessors to page table entries instead of direct dereference LoongArch: Enable general EFI poweroff method
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queueJakub Kicinski authored
Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-08-07 (ice) This series contains updates to ice driver only. Grzegorz adds IRQ synchronization call before performing reset and prevents writing to hardware when it is resetting. Mateusz swaps incorrect assignment of FEC statistics. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: ice: Fix incorrect assigns of FEC counts ice: Skip PTP HW writes during PTP reset procedure ice: Fix reset handler ==================== Link: https://patch.msgid.link/20240807224521.3819189-1-anthony.l.nguyen@intel.comSigned-off-by:
-
Martin Whitaker authored
As noted in the device errata [1-8], EEE support is not fully operational in the KSZ8567, KSZ9477, KSZ9567, KSZ9896, and KSZ9897 devices, causing link drops when connected to another device that supports EEE. The patch series "net: add EEE support for KSZ9477 switch family" merged in commit 9b0bf4f7 caused EEE support to be enabled in these devices. A fix for this regression for the KSZ9477 alone was merged in commit 08c6d8ba. This patch extends this fix to the other affected devices. [1] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/Errata/KSZ8567R-Errata-DS80000752.pdf [2] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/Errata/KSZ8567S-Errata-DS80000753.pdf [3] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/Errata/KSZ9477S-Errata-DS80000754.pdf [4] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/Errata/KSZ9567R-Errata-DS80000755.pdf [5] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/Errata/KSZ9567S-Errata-DS80000756.pdf [6] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/Errata/KSZ9896C-Errata-DS80000757.pdf [7] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/Errata/KSZ9897R-Errata-DS80000758.pdf [8] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/Errata/KSZ9897S-Errata-DS80000759.pdf Fixes: 69d3b36c ("net: dsa: microchip: enable EEE support") # for KSZ8567/KSZ9567/KSZ9896/KSZ9897 Link: https://lore.kernel.org/netdev/137ce1ee-0b68-4c96-a717-c8164b514eec@martin-whitaker.me.uk/Signed-off-by:
Martin Whitaker <foss@martin-whitaker.me.uk> Acked-by:
Arun Ramadoss <arun.ramadoss@microchip.com> Reviewed-by:
Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by:
Lukasz Majewski <lukma@denx.de> Link: https://patch.msgid.link/20240807205209.21464-1-foss@martin-whitaker.me.ukSigned-off-by:
-
Gal Pressman authored
The 'at least one change' requirement is not applicable for context creation, skip the check in such case. This allows a command such as 'ethtool -X eth0 context new' to work. The command works by mistake when using older versions of userspace ethtool due to an incompatibility issue where rxfh.input_xfrm is passed as zero (unset) instead of RXH_XFRM_NO_CHANGE as done with recent userspace. This patch does not try to solve the incompatibility issue. Link: https://lore.kernel.org/netdev/05ae8316-d3aa-4356-98c6-55ed4253c8a7@nvidia.com/ Fixes: 84a1d9c4 ("net: ethtool: extend RXNFC API to support RSS spreading of filter matches") Reviewed-by:
Jianbo Liu <jianbol@nvidia.com> Signed-off-by:
Edward Cree <ecree.xilinx@gmail.com> Link: https://patch.msgid.link/20240807173352.3501746-1-gal@nvidia.comSigned-off-by:
-
Edward Cree authored
Both ethtool_ops.rxfh_max_context_id and the default value used when it's not specified are supposed to be exclusive maxima (the former is documented as such; the latter, U32_MAX, cannot be used as an ID since it equals ETH_RXFH_CONTEXT_ALLOC), but xa_alloc() expects an inclusive maximum. Subtract one from 'limit' to produce an inclusive maximum, and pass that to xa_alloc(). Increase bnxt's max by one to prevent a (very minor) regression, as BNXT_MAX_ETH_RSS_CTX is an inclusive max. This is safe since bnxt is not actually hard-limited; BNXT_MAX_ETH_RSS_CTX is just a leftover from old driver code that managed context IDs itself. Rename rxfh_max_context_id to rxfh_max_num_contexts to make its semantics (hopefully) more obvious. Fixes: 847a8ab1 ("net: ethtool: let the core choose RSS context IDs") Signed-off-by:
-
Arnd Bergmann authored
Using FIELD_GET() fails in configurations that don't already include the header file indirectly: drivers/net/pse-pd/tps23881.c: In function 'tps23881_i2c_probe': drivers/net/pse-pd/tps23881.c:755:13: error: implicit declaration of function 'FIELD_GET' [-Wimplicit-function-declaration] 755 | if (FIELD_GET(TPS23881_REG_DEVID_MASK, ret) != TPS23881_DEVICE_ID) { | ^~~~~~~~~ Fixes: 89108cb5 ("net: pse-pd: tps23881: Fix the device ID check") Signed-off-by:Arnd Bergmann <arnd@arndb.de> Acked-by:
-
Csókás, Bence authored
PPS was not stopped in `fec_ptp_stop()`, called when the adapter was removed. Consequentially, you couldn't safely reload the driver with the PPS signal on. Fixes: 32cba57b ("net: fec: introduce fec_ptp_stop and use in probe fail path") Reviewed-by:
Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/netdev/CAOMZO5BzcZR8PwKKwBssQq_wAGzVgf1ffwe_nhpQJjviTdxy-w@mail.gmail.com/T/#m01dcb810bfc451a492140f6797ca77443d0cb79fSigned-off-by:
Csókás, Bence <csokas.bence@prolan.hu> Reviewed-by:
-
Florian Fainelli authored
Some Wake-on-LAN modes such as WAKE_FILTER may only be supported by the MAC, while others might be only supported by the PHY. Make sure that the .get_wol() returns the union of both rather than only that of the PHY if the PHY supports Wake-on-LAN. Fixes: 7e400ff3 ("net: bcmgenet: Add support for PHY-based Wake-on-LAN") Signed-off-by:
-
James Chapman authored
When l2tp tunnels use a socket provided by userspace, we can hit lockdep splats like the below when data is transmitted through another (unrelated) userspace socket which then gets routed over l2tp. This issue was previously discussed here: https://lore.kernel.org/netdev/87sfialu2n.fsf@cloudflare.com/ The solution is to have lockdep treat socket locks of l2tp tunnel sockets separately than those of standard INET sockets. To do so, use a different lockdep subclass where lock nesting is possible. ============================================ WARNING: possible recursive locking detected 6.10.0+ #34 Not tainted -------------------------------------------- iperf3/771 is trying to acquire lock: ffff8881027601d8 (slock-AF_INET/1){+.-.}-{2:2}, at: l2tp_xmit_skb+0x243/0x9d0 but task is already holding lock: ffff888102650d98 (slock-AF_INET/1){+.-.}-{2:2}, at: tcp_v4_rcv+0x1848/0x1e10 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(slock-AF_INET/1); lock(slock-AF_INET/1); *** DEADLOCK *** May be due to missing lock nesting notation 10 locks held by iperf3/771: #0: ffff888102650258 (sk_lock-AF_INET){+.+.}-{0:0}, at: tcp_sendmsg+0x1a/0x40 #1: ffffffff822ac220 (rcu_read_lock){....}-{1:2}, at: __ip_queue_xmit+0x4b/0xbc0 #2: ffffffff822ac220 (rcu_read_lock){....}-{1:2}, at: ip_finish_output2+0x17a/0x1130 #3: ffffffff822ac220 (rcu_read_lock){....}-{1:2}, at: process_backlog+0x28b/0x9f0 #4: ffffffff822ac220 (rcu_read_lock){....}-{1:2}, at: ip_local_deliver_finish+0xf9/0x260 #5: ffff888102650d98 (slock-AF_INET/1){+.-.}-{2:2}, at: tcp_v4_rcv+0x1848/0x1e10 #6: ffffffff822ac220 (rcu_read_lock){....}-{1:2}, at: __ip_queue_xmit+0x4b/0xbc0 #7: ffffffff822ac220 (rcu_read_lock){....}-{1:2}, at: ip_finish_output2+0x17a/0x1130 #8: ffffffff822ac1e0 (rcu_read_lock_bh){....}-{1:2}, at: __dev_queue_xmit+0xcc/0x1450 #9: ffff888101f33258 (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock#2){+...}-{2:2}, at: __dev_queue_xmit+0x513/0x1450 stack backtrace: CPU: 2 UID: 0 PID: 771 Comm: iperf3 Not tainted 6.10.0+ #34 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Call Trace: <IRQ> dump_stack_lvl+0x69/0xa0 dump_stack+0xc/0x20 __lock_acquire+0x135d/0x2600 ? srso_alias_return_thunk+0x5/0xfbef5 lock_acquire+0xc4/0x2a0 ? l2tp_xmit_skb+0x243/0x9d0 ? __skb_checksum+0xa3/0x540 _raw_spin_lock_nested+0x35/0x50 ? l2tp_xmit_skb+0x243/0x9d0 l2tp_xmit_skb+0x243/0x9d0 l2tp_eth_dev_xmit+0x3c/0xc0 dev_hard_start_xmit+0x11e/0x420 sch_direct_xmit+0xc3/0x640 __dev_queue_xmit+0x61c/0x1450 ? ip_finish_output2+0xf4c/0x1130 ip_finish_output2+0x6b6/0x1130 ? srso_alias_return_thunk+0x5/0xfbef5 ? __ip_finish_output+0x217/0x380 ? srso_alias_return_thunk+0x5/0xfbef5 __ip_finish_output+0x217/0x380 ip_output+0x99/0x120 __ip_queue_xmit+0xae4/0xbc0 ? srso_alias_return_thunk+0x5/0xfbef5 ? srso_alias_return_thunk+0x5/0xfbef5 ? tcp_options_write.constprop.0+0xcb/0x3e0 ip_queue_xmit+0x34/0x40 __tcp_transmit_skb+0x1625/0x1890 __tcp_send_ack+0x1b8/0x340 tcp_send_ack+0x23/0x30 __tcp_ack_snd_check+0xa8/0x530 ? srso_alias_return_thunk+0x5/0xfbef5 tcp_rcv_established+0x412/0xd70 tcp_v4_do_rcv+0x299/0x420 tcp_v4_rcv+0x1991/0x1e10 ip_protocol_deliver_rcu+0x50/0x220 ip_local_deliver_finish+0x158/0x260 ip_local_deliver+0xc8/0xe0 ip_rcv+0xe5/0x1d0 ? __pfx_ip_rcv+0x10/0x10 __netif_receive_skb_one_core+0xce/0xe0 ? process_backlog+0x28b/0x9f0 __netif_receive_skb+0x34/0xd0 ? process_backlog+0x28b/0x9f0 process_backlog+0x2cb/0x9f0 __napi_poll.constprop.0+0x61/0x280 net_rx_action+0x332/0x670 ? srso_alias_return_thunk+0x5/0xfbef5 ? find_held_lock+0x2b/0x80 ? srso_alias_return_thunk+0x5/0xfbef5 ? srso_alias_return_thunk+0x5/0xfbef5 handle_softirqs+0xda/0x480 ? __dev_queue_xmit+0xa2c/0x1450 do_softirq+0xa1/0xd0 </IRQ> <TASK> __local_bh_enable_ip+0xc8/0xe0 ? __dev_queue_xmit+0xa2c/0x1450 __dev_queue_xmit+0xa48/0x1450 ? ip_finish_output2+0xf4c/0x1130 ip_finish_output2+0x6b6/0x1130 ? srso_alias_return_thunk+0x5/0xfbef5 ? __ip_finish_output+0x217/0x380 ? srso_alias_return_thunk+0x5/0xfbef5 __ip_finish_output+0x217/0x380 ip_output+0x99/0x120 __ip_queue_xmit+0xae4/0xbc0 ? srso_alias_return_thunk+0x5/0xfbef5 ? srso_alias_return_thunk+0x5/0xfbef5 ? tcp_options_write.constprop.0+0xcb/0x3e0 ip_queue_xmit+0x34/0x40 __tcp_transmit_skb+0x1625/0x1890 tcp_write_xmit+0x766/0x2fb0 ? __entry_text_end+0x102ba9/0x102bad ? srso_alias_return_thunk+0x5/0xfbef5 ? __might_fault+0x74/0xc0 ? srso_alias_return_thunk+0x5/0xfbef5 __tcp_push_pending_frames+0x56/0x190 tcp_push+0x117/0x310 tcp_sendmsg_locked+0x14c1/0x1740 tcp_sendmsg+0x28/0x40 inet_sendmsg+0x5d/0x90 sock_write_iter+0x242/0x2b0 vfs_write+0x68d/0x800 ? __pfx_sock_write_iter+0x10/0x10 ksys_write+0xc8/0xf0 __x64_sys_write+0x3d/0x50 x64_sys_call+0xfaf/0x1f50 do_syscall_64+0x6d/0x140 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f4d143af992 Code: c3 8b 07 85 c0 75 24 49 89 fb 48 89 f0 48 89 d7 48 89 ce 4c 89 c2 4d 89 ca 4c 8b 44 24 08 4c 8b 4c 24 10 4c 89 5c 24 08 0f 05 <c3> e9 01 cc ff ff 41 54 b8 02 00 00 0 RSP: 002b:00007ffd65032058 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 0000000000000001 RCX: 00007f4d143af992 RDX: 0000000000000025 RSI: 00007f4d143f3bcc RDI: 0000000000000005 RBP: 00007f4d143f2b28 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f4d143f3bcc R13: 0000000000000005 R14: 0000000000000000 R15: 00007ffd650323f0 </TASK> Fixes: 0b2c5972 ("l2tp: close all race conditions in l2tp_tunnel_register()") Suggested-by:
James Chapman <jchapman@katalix.com> Signed-off-by:
Tom Parkin <tparkin@katalix.com> Link: https://patch.msgid.link/20240806160626.1248317-1-jchapman@katalix.comSigned-off-by:
-
