- 26 Jan, 2012 16 commits
-
-
Takashi Iwai authored
commit f2cbba76 upstream. When multiple headphone or other detectable output pins are present, the power-map has to be updated after resume appropriately, but the current driver doesn't check all pins but only the first pin (since it's enough to check it for the mute-behavior). This resulted in the silent output from the secondary outputs after PM resume. This patch fixes the problem by checking all pins at (re-)init time. Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=740347Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Takashi Iwai authored
commit 4808d12d upstream. Currently the driver checks only the out_mix_path[] for the primary output route for judging whether to create the loopback-mixing control or not. But, there are cases where aamix-routing is available only on headphone or speaker paths but not on the primary output path. So, the driver ignores such cases inappropriately. This patch fixes the check of the loopback-mixing control by testing all mix-routing paths. Signed-off-by:
-
Takashi Iwai authored
commit 3a90274d upstream. When an invalid NID is given, get_wcaps() returns zero as the error, but get_wcaps_type() takes it as the normal value and returns a bogus AC_WID_AUD_OUT value. This confuses the parser. With this patch, get_wcaps_type() returns -1 when value 0 is given, i.e. an invalid NID is passed to get_wcaps(). Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=740118Signed-off-by:
-
Takashi Iwai authored
commit de4da59e upstream. These laptops can work well with the auto-parser and their BIOS setups, and in addition, the auto-parser fixes the problem with S3/S4 where the unsol event handling is killed after resume due to fallback to the single-cmd mode. Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=740115Signed-off-by:
-
Takashi Iwai authored
commit 80c8a2a3 upstream. With some buggy devices, the usb-audio driver may give "frame xxx active" kernel messages too often. Better to keep it as debug-only using snd_printdd(), and also add the rate-limit for avoiding floods. Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=738681Signed-off-by:
-
Pavel Hofman authored
commit e7848163 upstream. Cards with identical PCI ids but no AC97 config in EEPROM do not have the ac97 field initialized. We must check for this case to avoid kernel oops. Signed-off-by:
Pavel Hofman <pavel.hofman@ivitera.com> Signed-off-by:
-
David Henningsson authored
commit 78e2a928 upstream. There was a bug in the automute logic causing speakers not to mute when headphones were plugged in. Tested-by:
Hsin-Yi Chen <hychen@canonical.com> Signed-off-by:
David Henningsson <david.henningsson@canonical.com> Signed-off-by:
-
David Henningsson authored
commit 40d03e63 upstream. The control name "HP/Speakers" is non-standard, and since there is only one DAC on this chip there is no need for a virtual master anyway. Signed-off-by:
-
Karsten Wiese authored
commit d0f3a2eb upstream. They are not needed here. Signed-off-by:
Karsten Wiese <fzu@wemgehoertderstaat.de> Signed-off-by:
-
Xi Wang authored
commit d50f2ab6 upstream. Commit 503358ae ("ext4: avoid divide by zero when trying to mount a corrupted file system") fixes CVE-2009-4307 by performing a sanity check on s_log_groups_per_flex, since it can be set to a bogus value by an attacker. sbi->s_log_groups_per_flex = sbi->s_es->s_log_groups_per_flex; groups_per_flex = 1 << sbi->s_log_groups_per_flex; if (groups_per_flex < 2) { ... } This patch fixes two potential issues in the previous commit. 1) The sanity check might only work on architectures like PowerPC. On x86, 5 bits are used for the shifting amount. That means, given a large s_log_groups_per_flex value like 36, groups_per_flex = 1 << 36 is essentially 1 << 4 = 16, rather than 0. This will bypass the check, leaving s_log_groups_per_flex and groups_per_flex inconsistent. 2) The sanity check relies on undefined behavior, i.e., oversized shift. A standard-confirming C compiler could rewrite the check in unexpected ways. Consider the following equivalent form, assuming groups_per_flex is unsigned for simplicity. groups_per_flex = 1 << sbi->s_log_groups_per_flex; if (groups_per_flex == 0 || groups_per_flex == 1) { We compile the code snippet using Clang 3.0 and GCC 4.6. Clang will completely optimize away the check groups_per_flex == 0, leaving the patched code as vulnerable as the original. GCC keeps the check, but there is no guarantee that future versions will do the same. Signed-off-by:
Xi Wang <xi.wang@gmail.com> Signed-off-by:
"Theodore Ts'o" <tytso@mit.edu> Signed-off-by:
-
Djalal Harouni authored
commit 014a1770 upstream. Online resize ioctls 'EXT4_IOC_GROUP_EXTEND' and 'EXT4_IOC_GROUP_ADD' call ext4_resize_begin() to check permissions and to set the EXT4_RESIZING bit lock, they do their work and they must finish with ext4_resize_end() which calls clear_bit_unlock() to unlock and to avoid -EBUSY errors for the next resize operations. This patch adds the missing ext4_resize_end() calls on error paths. Patch tested. Signed-off-by:
Djalal Harouni <tixxdz@opendz.org> Signed-off-by:
-
Ben Hutchings authored
commit e74a8f2e upstream. Commit f44f7f96 ("RTC: Initialize kernel state from RTC") introduced a potential infinite loop. If an alarm time contains a wildcard month and an invalid day (> 31), or a wildcard year and an invalid month (>= 12), the loop searching for the next matching date will never terminate. Treat the invalid values as wildcards. Fixes <http://bugs.debian.org/646429>, <http://bugs.debian.org/653331> Reported-by:
leo weppelman <leoweppelman@googlemail.com> Reported-by:
"P. van Gaans" <mailme667@yahoo.co.uk> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
Jonathan Nieder <jrnieder@gmail.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <john.stultz@linaro.org> Acked-by:
Alessandro Zummo <a.zummo@towertech.it> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Wolfram Sang authored
commit 2f4478cc upstream. stresstest needs at least two eraseblocks. Bail out gracefully if that condition is not met. Fixes the following 'division by zero' OOPS: [ 619.100000] mtd_stresstest: MTD device size 131072, eraseblock size 131072, page size 2048, count of eraseblocks 1, pages per eraseblock 64, OOB size 64 [ 619.120000] mtd_stresstest: scanning for bad eraseblocks [ 619.120000] mtd_stresstest: scanned 1 eraseblocks, 0 are bad [ 619.130000] mtd_stresstest: doing operations [ 619.130000] mtd_stresstest: 0 operations done [ 619.140000] Division by zero in kernel. ... caused by /* Read or write up 2 eraseblocks at a time - hence 'ebcnt - 1' */ eb %= (ebcnt - 1); Signed-off-by:
Wolfram Sang <w.sang@pengutronix.de> Signed-off-by:
Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by:
David Woodhouse <David.Woodhouse@intel.com> Signed-off-by:
-
Brian Norris authored
commit 342ff28f upstream. Some error paths in mtd_blkdevs were fixed in the following commit: commit 94735ec4 mtd: mtd_blkdevs: fix error path in blktrans_open But on these error paths, the block device's `dev->open' count is already incremented before we check for errors. This meant that, while the error path was handled correctly on the first time through blktrans_open(), the device is erroneously considered already open on the second time through. This problem can be seen, for instance, when a UBI volume is simultaneously mounted as a UBIFS partition and read through its corresponding gluebi mtdblockX device. This results in blktrans_open() passing its error checks (with `dev->open > 0') without actually having a handle on the device. Here's a summarized log of the actions and results with nandsim: # modprobe nandsim # modprobe mtdblock # modprobe gluebi # modprobe ubifs # ubiattach /dev/ubi_ctrl -m 0 ... # ubimkvol /dev/ubi0 -N test -s 16MiB ... # mount -t ubifs ubi0:test /mnt # ls /dev/mtdblock* /dev/mtdblock0 /dev/mtdblock1 # cat /dev/mtdblock1 > /dev/null cat: can't open '/dev/mtdblock4': Device or resource busy # cat /dev/mtdblock1 > /dev/null CPU 0 Unable to handle kernel paging request at virtual address fffffff0, epc == 8031536c, ra == 8031f280 Oops[#1]: ... Call Trace: [<8031536c>] ubi_leb_read+0x14/0x164 [<8031f280>] gluebi_read+0xf0/0x148 [<802edba8>] mtdblock_readsect+0x64/0x198 [<802ecfe4>] mtd_blktrans_thread+0x330/0x3f4 [<8005be98>] kthread+0x88/0x90 [<8000bc04>] kernel_thread_helper+0x10/0x18 Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
Roman Tereshonkov authored
commit 3538c563 upstream. Use block_isbad to check and skip the bad blocks reading. This will allow to get rid of the read errors if bad blocks are present initially. Signed-off-by:
Roman Tereshonkov <roman.tereshonkov@nokia.com> Signed-off-by:
-
Roman Tereshonkov authored
commit 556f0635 upstream. The array of unsigned long pointed by oops_page_used is allocated by vmalloc which requires the size to be in bytes. BITS_PER_LONG is equal to 32. If we want to allocate memory for 32 pages with one bit per page then 32 / BITS_PER_LONG is equal to 1 byte that is 8 bits. To fix it we need to multiply the result by sizeof(unsigned long) equal to 4. Signed-off-by:
-
- 12 Jan, 2012 24 commits
-
-
Greg Kroah-Hartman authored
-
Xi Wang authored
commit 093019cf upstream. Commit fa8b18ed didn't prevent the integer overflow and possible memory corruption. "count" can go negative and bypass the check. Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Ben Myers <bpm@sgi.com> Signed-off-by:
-
Thilo-Alexander Ginkel authored
[Not upstream as it was fixed differently for 3.3 with a much more "intrusive" rework of the driver - gregkh] There is a race condition involving acm_tty_hangup() and acm_tty_close() where hangup() would attempt to access tty->driver_data without proper locking and NULL checking after close() has potentially already set it to NULL. One possibility to (sporadically) trigger this behavior is to perform a suspend/resume cycle with a running WWAN data connection. This patch addresses the issue by introducing a NULL check for tty->driver_data in acm_tty_hangup() protected by open_mutex and exiting gracefully when hangup() is invoked on a device that has already been closed. Signed-off-by:
Thilo-Alexander Ginkel <thilo@ginkel.com> Signed-off-by:
-
stephen hemminger authored
commit f7d9821a upstream. If slave device already has a receive handler registered, then the error unwind of bonding device enslave function is broken. The following will leave a pointer to freed memory in the slave device list, causing a later kernel panic. # modprobe dummy # ip li add dummy0-1 link dummy0 type macvlan # modprobe bonding # echo +dummy0 >/sys/class/net/bond0/bonding/slaves The fix is to detach the slave (which removes it from the list) in the unwind path. Signed-off-by:
Stephen Hemminger <shemminger@vyatta.com> Reviewed-by:
Nicolas de Pesloüan <nicolas.2p.debian@free.fr> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Aurelien Jacobs authored
commit 6c15d74d upstream. At this point if skb->len happens to be 2, the subsequant skb_pull(skb, 4) call won't work and the skb->len won't be decreased and won't ever reach 0, resulting in an infinite loop. With an ASIX 88772 under heavy load, without this patch, rx_fixup() reaches an infinite loop in less than a minute. With this patch applied, no infinite loop even after hours of heavy load. Signed-off-by:
Aurelien Jacobs <aurel@gnuage.org> Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by:
-
Ben Hutchings authored
commit a8c1f65c upstream. Commit 5b7c8406 ('ipv4: correct IGMP behavior on v3 query during v2-compatibility mode') added yet another case for query parsing, which can result in max_delay = 0. Substitute a value of 1, as in the usual v3 case. Reported-by:
Simon McVittie <smcv@debian.org> References: http://bugs.debian.org/654876Signed-off-by:
-
Felipe Balbi authored
commit 18b7ede5 upstream. [ removed the dwc3 portion of the patch as it didn't apply to older kernels - gregkh] According to USB 3.0 Specification Table 9-22, if bmAttributes [4:0] are set to zero, it means "no streams supported", but the way this helper was defined on Linux, we will *always* have one stream which might cause several problems. For example on DWC3, we would tell the controller endpoint has streams enabled and yet start transfers with Stream ID set to 0, which would goof up the host side. While doing that, convert the macro to an inline function due to the different checks we now need. Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by:
-
Hans de Goede authored
commit 71d85724 upstream. I encountered a result of COMP_2ND_BW_ERR while improving how the pwc webcam driver handles not having the full usb1 bandwidth available to itself. I created the following test setup, a NEC xhci controller with a single TT USB 2 hub plugged into it, with a usb keyboard and a pwc webcam plugged into the usb2 hub. This caused the following to show up in dmesg when trying to stream from the pwc camera at its highest alt setting: xhci_hcd 0000:01:00.0: ERROR: unexpected command completion code 0x23. usb 6-2.1: Not enough bandwidth for altsetting 9 And usb_set_interface returned -EINVAL, which caused my pwc code to not do the right thing as it expected -ENOSPC. This patch makes the xhci driver properly handle COMP_2ND_BW_ERR and makes usb_set_interface return -ENOSPC as expected. This should be backported to stable kernels as old as 2.6.32. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Clemens Ladisch authored
commit bc677d5b upstream. Add a new field num_mapped_sgs to struct urb so that we have a place to store the number of mapped entries and can also retain the original value of entries in num_sgs. Previously, usb_hcd_map_urb_for_dma() would overwrite this with the number of mapped entries, which would break dma_unmap_sg() because it requires the original number of entries. This fixes warnings like the following when using USB storage devices: ------------[ cut here ]------------ WARNING: at lib/dma-debug.c:902 check_unmap+0x4e4/0x695() ehci_hcd 0000:00:12.2: DMA-API: device driver frees DMA sg list with different entry count [map count=4] [unmap count=1] Modules linked in: ohci_hcd ehci_hcd Pid: 0, comm: kworker/0:1 Not tainted 3.2.0-rc2+ #319 Call Trace: <IRQ> [<ffffffff81036d3b>] warn_slowpath_common+0x80/0x98 [<ffffffff81036de7>] warn_slowpath_fmt+0x41/0x43 [<ffffffff811fa5ae>] check_unmap+0x4e4/0x695 [<ffffffff8105e92c>] ? trace_hardirqs_off+0xd/0xf [<ffffffff8147208b>] ? _raw_spin_unlock_irqrestore+0x33/0x50 [<ffffffff811fa84a>] debug_dma_unmap_sg+0xeb/0x117 [<ffffffff8137b02f>] usb_hcd_unmap_urb_for_dma+0x71/0x188 [<ffffffff8137b166>] unmap_urb_for_dma+0x20/0x22 [<ffffffff8137b1c5>] usb_hcd_giveback_urb+0x5d/0xc0 [<ffffffffa0000d02>] ehci_urb_done+0xf7/0x10c [ehci_hcd] [<ffffffffa0001140>] qh_completions+0x429/0x4bd [ehci_hcd] [<ffffffffa000340a>] ehci_work+0x95/0x9c0 [ehci_hcd] ... ---[ end trace f29ac88a5a48c580 ]--- Mapped at: [<ffffffff811faac4>] debug_dma_map_sg+0x45/0x139 [<ffffffff8137bc0b>] usb_hcd_map_urb_for_dma+0x22e/0x478 [<ffffffff8137c494>] usb_hcd_submit_urb+0x63f/0x6fa [<ffffffff8137d01c>] usb_submit_urb+0x2c7/0x2de [<ffffffff8137dcd4>] usb_sg_wait+0x55/0x161 Signed-off-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
-
Malte Schröder authored
commit 08e87d0d upstream. Hi, below patch adds the USB-ID of the serial adapters sold by Multiplex RC (www.multiplex-rc.de). Signed-off-by:
Malte Schröder <maltesch@gmx.de> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Janne Snabb authored
commit 3c8c9316 upstream. Add support for Chinese Noname HSPA USB modem which is apparently manufactured by a company called ZD Incorporated (based on texts in the Windows drivers). This product is available at least from Dealextreme (SKU 80032) and possibly in India with name Olive V-MW250. It is based on Qualcomm MSM6280 chip. I needed to also add "options usb-storage quirks=0685:7000:i" in modprobe configuration because udevd or the kernel keeps poking the embedded fake-cd-rom which fails and causes the device to reset. There might be a better way to accomplish the same. usb_modeswitch is not needed with this device. Signed-off-by:
Janne Snabb <snabb@epipe.com> Signed-off-by:
-
Johan Hovold authored
commit 694c6301 upstream. Fix regression introduced by commit 507ca9bc ([PATCH] USB: add ability for usb-serial drivers to determine if their write urb is currently being used.) which inverted the logic in write_room so that it returns zero when the write urb is actually free. Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
-
Felipe Contreras authored
commit 772aed45 upstream. In musb_init_controller() there's a pm_runtime_put(), but there's no pm_runtime_get(), which creates a mismatch that causes the driver to sleep when it shouldn't. This was introduced in 7acc6197[1], but it wasn't triggered in my setup until 18a26892[2] was merged to Linus' branch at point df0914[3]. IOW; when PM is working as it was supposed to. However, it seems most of the time this is used in a way that keeps the counter above 0, so nobody noticed. Also, it seems to depend on the configuration used in versions before 3.1, but not later (or in it). I found the problem by loading isp1704_charger before any usb gadgets: http://article.gmane.org/gmane.linux.kernel/1226122 All versions after 2.6.39 are affected. [1] usb: musb: Idle path retention and offmode support for OMAP3 [2] OMAP2+: musb: hwmod adaptation for musb registration [3] Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 Cc: Hema HK <hemahk@ti.com> Signed-off-by:
Felipe Contreras <felipe.contreras@gmail.com> Signed-off-by:
-
Oliver Neukum authored
commit 35284b3d upstream. The Guillemot Webcam Hercules Dualpix Exchange camera has been reported with a second ID. Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
-
Tanmay Upadhyay authored
commit 35657c4d upstream. After commit c430131a (Support controllers with big endian capability regs), HC_LENGTH takes two arguments. This patch fixes following compilation error: In file included from drivers/usb/host/ehci-hcd.c:1323: drivers/usb/host/ehci-pxa168.c:302:54: error: macro "HC_LENGTH" requires 2 arguments, but only 1 given In file included from drivers/usb/host/ehci-hcd.c:1323: drivers/usb/host/ehci-pxa168.c: In function 'ehci_pxa168_drv_probe': drivers/usb/host/ehci-pxa168.c:302: error: 'HC_LENGTH' undeclared (first use in this function) drivers/usb/host/ehci-pxa168.c:302: error: (Each undeclared identifier is reported only once drivers/usb/host/ehci-pxa168.c:302: error: for each function it appears in.) Signed-off-by:
Tanmay Upadhyay <tanmay.upadhyay@einfochips.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Huajun Li authored
usb: usb-storage doesn't support dynamic id currently, the patch disables the feature to fix an oops commit 1a3a026b upstream. Echo vendor and product number of a non usb-storage device to usb-storage driver's new_id, then plug in the device to host and you will find following oops msg, the root cause is usb_stor_probe1() refers invalid id entry if giving a dynamic id, so just disable the feature. [ 3105.018012] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC [ 3105.018062] CPU 0 [ 3105.018075] Modules linked in: usb_storage usb_libusual bluetooth dm_crypt binfmt_misc snd_hda_codec_analog snd_hda_intel snd_hda_codec snd_hwdep hp_wmi ppdev sparse_keymap snd_pcm snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer snd_seq_device psmouse snd serio_raw tpm_infineon soundcore i915 snd_page_alloc tpm_tis parport_pc tpm tpm_bios drm_kms_helper drm i2c_algo_bit video lp parport usbhid hid sg sr_mod sd_mod ehci_hcd uhci_hcd usbcore e1000e usb_common floppy [ 3105.018408] [ 3105.018419] Pid: 189, comm: khubd Tainted: G I 3.2.0-rc7+ #29 Hewlett-Packard HP Compaq dc7800p Convertible Minitower/0AACh [ 3105.018481] RIP: 0010:[<ffffffffa045830d>] [<ffffffffa045830d>] usb_stor_probe1+0x2fd/0xc20 [usb_storage] [ 3105.018536] RSP: 0018:ffff880056a3d830 EFLAGS: 00010286 [ 3105.018562] RAX: ffff880065f4e648 RBX: ffff88006bb28000 RCX: 0000000000000000 [ 3105.018597] RDX: ffff88006f23c7b0 RSI: 0000000000000001 RDI: 0000000000000206 [ 3105.018632] RBP: ffff880056a3d900 R08: 0000000000000000 R09: ffff880067365000 [ 3105.018665] R10: 00000000000002ac R11: 0000000000000010 R12: ffff6000b41a7340 [ 3105.018698] R13: ffff880065f4ef60 R14: ffff88006bb28b88 R15: ffff88006f23d270 [ 3105.018733] FS: 0000000000000000(0000) GS:ffff88007a200000(0000) knlGS:0000000000000000 [ 3105.018773] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [ 3105.018801] CR2: 00007fc99c8c4650 CR3: 0000000001e05000 CR4: 00000000000006f0 [ 3105.018835] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 3105.018870] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 [ 3105.018906] Process khubd (pid: 189, threadinfo ffff880056a3c000, task ffff88005677a400) [ 3105.018945] Stack: [ 3105.018959] 0000000000000000 0000000000000000 ffff880056a3d8d0 0000000000000002 [ 3105.019011] 0000000000000000 ffff880056a3d918 ffff880000000000 0000000000000002 [ 3105.019058] ffff880056a3d8d0 0000000000000012 ffff880056a3d8d0 0000000000000006 [ 3105.019105] Call Trace: [ 3105.019128] [<ffffffffa0458cd4>] storage_probe+0xa4/0xe0 [usb_storage] [ 3105.019173] [<ffffffffa0097822>] usb_probe_interface+0x172/0x330 [usbcore] [ 3105.019211] [<ffffffff815fda67>] driver_probe_device+0x257/0x3b0 [ 3105.019243] [<ffffffff815fdd43>] __device_attach+0x73/0x90 [ 3105.019272] [<ffffffff815fdcd0>] ? __driver_attach+0x110/0x110 [ 3105.019303] [<ffffffff815fb93c>] bus_for_each_drv+0x9c/0xf0 [ 3105.019334] [<ffffffff815fd6c7>] device_attach+0xf7/0x120 [ 3105.019364] [<ffffffff815fc905>] bus_probe_device+0x45/0x80 [ 3105.019396] [<ffffffff815f98a6>] device_add+0x876/0x990 [ 3105.019434] [<ffffffffa0094e42>] usb_set_configuration+0x822/0x9e0 [usbcore] [ 3105.019479] [<ffffffffa00a3492>] generic_probe+0x62/0xf0 [usbcore] [ 3105.019518] [<ffffffffa0097a46>] usb_probe_device+0x66/0xb0 [usbcore] [ 3105.019555] [<ffffffff815fda67>] driver_probe_device+0x257/0x3b0 [ 3105.019589] [<ffffffff815fdd43>] __device_attach+0x73/0x90 [ 3105.019617] [<ffffffff815fdcd0>] ? __driver_attach+0x110/0x110 [ 3105.019648] [<ffffffff815fb93c>] bus_for_each_drv+0x9c/0xf0 [ 3105.019680] [<ffffffff815fd6c7>] device_attach+0xf7/0x120 [ 3105.019709] [<ffffffff815fc905>] bus_probe_device+0x45/0x80 [ 3105.021040] usb usb6: usb auto-resume [ 3105.021045] usb usb6: wakeup_rh [ 3105.024849] [<ffffffff815f98a6>] device_add+0x876/0x990 [ 3105.025086] [<ffffffffa0088987>] usb_new_device+0x1e7/0x2b0 [usbcore] [ 3105.025086] [<ffffffffa008a4d7>] hub_thread+0xb27/0x1ec0 [usbcore] [ 3105.025086] [<ffffffff810d5200>] ? wake_up_bit+0x50/0x50 [ 3105.025086] [<ffffffffa00899b0>] ? usb_remote_wakeup+0xa0/0xa0 [usbcore] [ 3105.025086] [<ffffffff810d49b8>] kthread+0xd8/0xf0 [ 3105.025086] [<ffffffff81939884>] kernel_thread_helper+0x4/0x10 [ 3105.025086] [<ffffffff8192a8c0>] ? _raw_spin_unlock_irq+0x50/0x80 [ 3105.025086] [<ffffffff8192b1b4>] ? retint_restore_args+0x13/0x13 [ 3105.025086] [<ffffffff810d48e0>] ? __init_kthread_worker+0x80/0x80 [ 3105.025086] [<ffffffff81939880>] ? gs_change+0x13/0x13 [ 3105.025086] Code: 00 48 83 05 cd ad 00 00 01 48 83 05 cd ad 00 00 01 4c 8b ab 30 0c 00 00 48 8b 50 08 48 83 c0 30 48 89 45 a0 4c 89 a3 40 0c 00 00 <41> 0f b6 44 24 10 48 89 55 a8 3c ff 0f 84 b8 04 00 00 48 83 05 [ 3105.025086] RIP [<ffffffffa045830d>] usb_stor_probe1+0x2fd/0xc20 [usb_storage] [ 3105.025086] RSP <ffff880056a3d830> [ 3105.060037] hub 6-0:1.0: hub_resume [ 3105.062616] usb usb5: usb auto-resume [ 3105.064317] ehci_hcd 0000:00:1d.7: resume root hub [ 3105.094809] ---[ end trace a7919e7f17c0a727 ]--- [ 3105.130069] hub 5-0:1.0: hub_resume [ 3105.132131] usb usb4: usb auto-resume [ 3105.132136] usb usb4: wakeup_rh [ 3105.180059] hub 4-0:1.0: hub_resume [ 3106.290052] usb usb6: suspend_rh (auto-stop) [ 3106.290077] usb usb4: suspend_rh (auto-stop) Signed-off-by:
Huajun Li <huajun.li.lee@gmail.com> Signed-off-by:
-
Greg Kroah-Hartman authored
commit 59bf5cf9 upstream. We were sending data on the stack when uploading firmware, which causes some machines fits, and is not allowed. Fix this by using the buffer we already had around for this very purpose. Reported-by:
Wouter M. Koolen <wmkoolen@cwi.nl> Tested-by:
-
Julia Lawall authored
commit e7c8e860 upstream. On some failures, the country_code field of an acm structure is freed without freeing the acm structure itself. Elsewhere, operations including memcpy and kfree are performed on the country_code field. The patch sets the country_code field to NULL when it is freed, and likewise sets the country_code_size field to 0. Signed-off-by:
Julia Lawall <julia@diku.dk> Acked-by:
-
Jan Kara authored
commit d2eb8c35 upstream. During BKL removal in 2.6.38, conversion of files from in-ICB format to normal format got broken. We call ->writepage with i_data_sem held but udf_get_block() also acquires i_data_sem thus creating A-A deadlock. We fix the problem by dropping i_data_sem before calling ->writepage() which is safe since i_mutex still protects us against any changes in the file. Also fix pagelock - i_data_sem lock inversion in udf_expand_file_adinicb() by dropping i_data_sem before calling find_or_create_page(). Reported-by:
Matthias Matiak <netzpython@mail-on.us> Tested-by:
Namjae Jeon <linkinjeon@gmail.com> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Li Zefan authored
commit 0d19ea86 upstream. If we mount a hierarchy with a specified name, the name is unique, and we can use it to mount the hierarchy without specifying its set of subsystem names. This feature is documented is Documentation/cgroups/cgroups.txt section 2.3 Here's an example: # mount -t cgroup -o cpuset,name=myhier xxx /cgroup1 # mount -t cgroup -o name=myhier xxx /cgroup2 But it was broken by commit 32a8cf23 (cgroup: make the mount options parsing more accurate) This fixes the regression. Signed-off-by:
Li Zefan <lizf@cn.fujitsu.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Claudio Scordino authored
commit dbf1115d upstream. Patch to fix a spinlock lockup in the driver that sometimes happens when the tasklet starts. Signed-off-by:
Claudio Scordino <claudio@evidence.eu.com> Signed-off-by:
Dave Bender <codehero@gmail.com> Tested-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
-
Sarah Sharp authored
commit 1b41c832 upstream. When running the Point Grey "flycap" program for their USB 3.0 camera (which was running as a USB 2.0 device for some reason), I trigger this oops whenever I try to open a video stream: Dec 15 16:48:34 puck kernel: [ 1798.715559] BUG: unable to handle kernel NULL pointer dereference at (null) Dec 15 16:48:34 puck kernel: [ 1798.719153] IP: [<ffffffff8147841e>] free_async+0x1e/0x70 Dec 15 16:48:34 puck kernel: [ 1798.720991] PGD 6f833067 PUD 6fc56067 PMD 0 Dec 15 16:48:34 puck kernel: [ 1798.722815] Oops: 0002 [#1] SMP Dec 15 16:48:34 puck kernel: [ 1798.724627] CPU 0 Dec 15 16:48:34 puck kernel: [ 1798.724636] Modules linked in: ecryptfs encrypted_keys sha1_generic trusted binfmt_misc sha256_generic aesni_intel cryptd aes_x86_64 aes_generic parport_pc dm_crypt ppdev joydev snd_hda_codec_hdmi snd_hda_codec_conexant arc4 iwlwifi snd_hda_intel snd_hda_codec snd_hwdep snd_pcm thinkpad_acpi mac80211 snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer btusb uvcvideo snd_seq_device bluetooth videodev psmouse snd v4l2_compat_ioctl32 serio_raw tpm_tis cfg80211 tpm tpm_bios nvram soundcore snd_page_alloc lp parport i915 xhci_hcd ahci libahci drm_kms_helper drm sdhci_pci sdhci e1000e i2c_algo_bit video Dec 15 16:48:34 puck kernel: [ 1798.734212] Dec 15 16:48:34 puck kernel: [ 1798.736162] Pid: 2713, comm: FlyCap2 Not tainted 3.2.0-rc5+ #28 LENOVO 4286CTO/4286CTO Dec 15 16:48:34 puck kernel: [ 1798.738148] RIP: 0010:[<ffffffff8147841e>] [<ffffffff8147841e>] free_async+0x1e/0x70 Dec 15 16:48:34 puck kernel: [ 1798.740134] RSP: 0018:ffff88005715fd78 EFLAGS: 00010296 Dec 15 16:48:34 puck kernel: [ 1798.742118] RAX: 00000000fffffff4 RBX: ffff88006fe8f900 RCX: 0000000000004118 Dec 15 16:48:34 puck kernel: [ 1798.744116] RDX: 0000000001000000 RSI: 0000000000016390 RDI: 0000000000000000 Dec 15 16:48:34 puck kernel: [ 1798.746087] RBP: ffff88005715fd88 R08: 0000000000000000 R09: ffffffff8146f22e Dec 15 16:48:34 puck kernel: [ 1798.748018] R10: ffff88006e520ac0 R11: 0000000000000001 R12: ffff88005715fe28 Dec 15 16:48:34 puck kernel: [ 1798.749916] R13: ffff88005d31df00 R14: ffff88006fe8f900 R15: 00007f688c995cb8 Dec 15 16:48:34 puck kernel: [ 1798.751785] FS: 00007f68a366da40(0000) GS:ffff880100200000(0000) knlGS:0000000000000000 Dec 15 16:48:34 puck kernel: [ 1798.753659] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 Dec 15 16:48:34 puck kernel: [ 1798.755509] CR2: 0000000000000000 CR3: 00000000706bb000 CR4: 00000000000406f0 Dec 15 16:48:34 puck kernel: [ 1798.757334] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 Dec 15 16:48:34 puck kernel: [ 1798.759124] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Dec 15 16:48:34 puck kernel: [ 1798.760871] Process FlyCap2 (pid: 2713, threadinfo ffff88005715e000, task ffff88006c675b80) Dec 15 16:48:34 puck kernel: [ 1798.762605] Stack: Dec 15 16:48:34 puck kernel: [ 1798.764297] ffff88005715fe28 0000000000000000 ffff88005715fe08 ffffffff81479058 Dec 15 16:48:34 puck kernel: [ 1798.766020] 0000000000000000 ffffea0000004000 ffff880000004118 0000000000000000 Dec 15 16:48:34 puck kernel: [ 1798.767750] ffff880000000001 ffff88006e520ac0 fffffff46fd81180 0000000000000000 Dec 15 16:48:34 puck kernel: [ 1798.769472] Call Trace: Dec 15 16:48:34 puck kernel: [ 1798.771147] [<ffffffff81479058>] proc_do_submiturb+0x778/0xa00 Dec 15 16:48:34 puck kernel: [ 1798.772798] [<ffffffff8147a5fd>] usbdev_do_ioctl+0x24d/0x1200 Dec 15 16:48:34 puck kernel: [ 1798.774410] [<ffffffff8147b5de>] usbdev_ioctl+0xe/0x20 Dec 15 16:48:34 puck kernel: [ 1798.775975] [<ffffffff81189259>] do_vfs_ioctl+0x99/0x600 Dec 15 16:48:34 puck kernel: [ 1798.777534] [<ffffffff81189851>] sys_ioctl+0x91/0xa0 Dec 15 16:48:34 puck kernel: [ 1798.779088] [<ffffffff816247c2>] system_call_fastpath+0x16/0x1b ec 15 16:48:34 puck kernel: [ 1798.780634] Code: 51 ff ff ff e9 29 ff ff ff 0f 1f 40 00 55 48 89 e5 53 48 83 ec 08 66 66 66 66 90 48 89 fb 48 8b 7f 18 e8 a6 ea c0 ff 4 8 8b 7b 20 <f0> ff 0f 0f 94 c0 84 c0 74 05 e8 d3 99 c1 ff 48 8b 43 40 48 8b Dec 15 16:48:34 puck kernel: [ 1798.783970] RIP [<ffffffff8147841e>] free_async+0x1e/0x70 Dec 15 16:48:34 puck kernel: [ 1798.785630] RSP <ffff88005715fd78> Dec 15 16:48:34 puck kernel: [ 1798.787274] CR2: 0000000000000000 Dec 15 16:48:34 puck kernel: [ 1798.794728] ---[ end trace 52894d3355f88d19 ]--- markup_oops.pl says the oops is in put_cred: ffffffff81478401: 48 89 e5 mov %rsp,%rbp ffffffff81478404: 53 push %rbx ffffffff81478405: 48 83 ec 08 sub $0x8,%rsp ffffffff81478409: e8 f2 c0 1a 00 callq ffffffff81624500 <mcount> ffffffff8147840e: 48 89 fb mov %rdi,%rbx | %ebx => ffff88006fe8f900 put_pid(as->pid); ffffffff81478411: 48 8b 7f 18 mov 0x18(%rdi),%rdi ffffffff81478415: e8 a6 ea c0 ff callq ffffffff81086ec0 <put_pid> put_cred(as->cred); ffffffff8147841a: 48 8b 7b 20 mov 0x20(%rbx),%rdi | %edi => 0 %ebx = ffff88006fe8f900 */ static inline int atomic_dec_and_test(atomic_t *v) { unsigned char c; asm volatile(LOCK_PREFIX "decl %0; sete %1" *ffffffff8147841e: f0 ff 0f lock decl (%rdi) | %edi = 0 <--- faulting instruction ffffffff81478421: 0f 94 c0 sete %al static inline void put_cred(const struct cred *_cred) { struct cred *cred = (struct cred *) _cred; validate_creds(cred); if (atomic_dec_and_test(&(cred)->usage)) ffffffff81478424: 84 c0 test %al,%al ffffffff81478426: 74 05 je ffffffff8147842d <free_async+0x2d> __put_cred(cred); ffffffff81478428: e8 d3 99 c1 ff callq ffffffff81091e00 <__put_cred> kfree(as->urb->transfer_buffer); ffffffff8147842d: 48 8b 43 40 mov 0x40(%rbx),%rax ffffffff81478431: 48 8b 78 68 mov 0x68(%rax),%rdi ffffffff81478435: e8 a6 e1 ce ff callq ffffffff811665e0 <kfree> kfree(as->urb->setup_packet); ffffffff8147843a: 48 8b 43 40 mov 0x40(%rbx),%rax ffffffff8147843e: 48 8b b8 90 00 00 00 mov 0x90(%rax),%rdi ffffffff81478445: e8 96 e1 ce ff callq ffffffff811665e0 <kfree> usb_free_urb(as->urb); ffffffff8147844a: 48 8b 7b 40 mov 0x40(%rbx),%rdi ffffffff8147844e: e8 0d 6b ff ff callq ffffffff8146ef60 <usb_free_urb> This bug seems to have been introduced by commit d178bc3a "user namespace: usb: make usb urbs user namespace aware (v2)" I'm not sure if this is right fix, but it does stop the oops. Unfortunately, the Point Grey software still refuses to work, but it's a closed source app, so I can't fix it. Signed-off-by:
Serge Hallyn <serge.hallyn@canonical.com> Signed-off-by:
-
Alan Stern authored
commit d8cae98c upstream. The documentation for usbmon is out of date; the usbfs "devices" file now exists in /sys/kernel/debug/usb rather than /proc/bus/usb. This patch (as1505) updates the documentation accordingly, and also mentions that the necessary information can be found by running lsusb. Signed-off-by:
-
K. Y. Srinivasan authored
commit 8f257a14 upstream. The function vmbus_exists() was introduced recently to deal with cases where the vmbus driver failed to initialize and yet other Hyper-V drivers attempted to register with the vmbus bus driver. This patch introduced a bug where vmbus_driver_unregister() would fail to unregister the driver. This patch fixes the problem. Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Signed-off-by:
Fuzhou Chen <fuzhouch@microsoft.com> Cc: Sasha Levin <levinsasha928@gmail.com> Signed-off-by:
-
