- 29 Oct, 2018 5 commits
-
-
Douglas Anderson authored
Let's solve the mystery of commit bf1178c9 ("drm/bridge: ti-sn65dsi86: Add mystery delay to enable()"). Specifically the reason we needed that mystery delay is that we weren't paying attention to HPD. Looking at the datasheet for the same panel that was tested for the original commit, I see there's a timing "t3" that times from power on to the aux channel being operational. This time is specced as 0 - 200 ms. The datasheet says that the aux channel is operational at exactly the same time that HPD is asserted. Scoping the signals on this board showed that HPD was asserted 84 ms after power was asserted. That very closely matches the magic 70 ms delay that we had. ...and actually, in my testing the 70 ms wasn't quite enough of a delay and some percentage of the time the display didn't come up until I bumped it to 100 ms (presumably 84 ms would have worked too). To solve this, we tried to hook up the HPD signal in the bridge. ...but in doing so we found that that the bridge didn't report that HPD was asserted until ~280 ms after we powered it (!). This is explained by looking at the sn65dsi86 datasheet section "8.4.5.1 HPD (Hot Plug/Unplug Detection)". Reading there we see that the bridge isn't even intended to report HPD until 100 ms after it's asserted. ...but that would have left us at 184 ms. The extra 100 ms (presumably) comes from this part in the datasheet: > The HPD state machine operates off an internal ring oscillator. The > ring oscillator frequency will vary [ ... ]. The min/max range in > the HPD State Diagram refers to the possible times based off > variation in the ring oscillator frequency. Given that the 280 ms we'll end up delaying if we hook up HPD is _slower_ than the 200 ms we could just hardcode, for now we'll solve the problem by just hardcoding a 200 ms delay in the panel driver using the patch in this series ("drm/panel: simple: Support panels with HPD where HPD isn't connected"). If we later find a panel that needs to use this bridge where we need HPD then we'll have to come up with some new code to handle it. Given the silly debouncing in the bridge chip, though, it seems unlikely. One last note is that I tried to solve this through another way: In ti_sn_bridge_enable() I tried to use various combinations of dp_dpcd_writeb() and dp_dpcd_readb() to detect when the aux channel was up. In theory that would let me detect _exactly_ when I could continue and do link training. Unfortunately even if I did an aux transfer w/out waiting I couldn't see any errors. Possibly I could keep looping over link training until it came back with success, but that seemed a little overly hacky to me. Reviewed-by:
Sean Paul <sean@poorly.run> Reviewed-by:
Andrzej Hajda <a.hajda@samsung.com> Signed-off-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20181025222134.174583-4-dianders@chromium.org
-
Douglas Anderson authored
If the HPD signal isn't hooked up to this panel we need a 200 ms delay. In the datasheet this is shown as the maximum time that HPD will take to be asserted after power is given to the panel. Reviewed-by:
-
Douglas Anderson authored
Some eDP panels that are designed to be always connected to a board use their HPD signal to signal that they've finished powering on and they're ready to be talked to. However, for various reasons it's possible that the HPD signal from the panel isn't actually hooked up. In the case where the HPD isn't hooked up you can look at the timing diagram on the panel datasheet and insert a delay for the maximum amount of time that the HPD might take to come up. Let's add support in simple-panel for this concept. At the moment we will co-opt the existing "prepare" delay to keep track of the delay and we'll use a boolean to specify that a given panel should only apply the delay if the "no-hpd" property was specified. Reviewed-by:
-
Douglas Anderson authored
Some eDP panels that are designed to be always connected to a board use their HPD signal to signal that they've finished powering on and they're ready to be talked to. However, for various reasons it's possible that the HPD signal from the panel isn't actually hooked up. In the case where the HPD isn't hooked up you can look at the timing diagram on the panel datasheet and insert a delay for the maximum amount of time that the HPD might take to come up. Let's add a property in the device tree for this concept. Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Lee, Shawn C authored
BOE panel (ID: 0x0771) that reports "DFP 1.x compliant TMDS". But it's 6bpc panel only instead of 8 bpc. Add panel ID to edid quirk list and set 6 bpc as default to work around this issue. Cc: Jani Nikula <jani.nikula@intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Cooper Chiou <cooper.chiou@intel.com> Signed-off-by:
Lee, Shawn C <shawn.c.lee@intel.com>> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/1540792173-7288-1-git-send-email-shawn.c.lee@intel.com
-
- 19 Oct, 2018 1 commit
-
-
Dave Airlie authored
Merge tag 'drm-intel-next-fixes-2018-10-18' of git://anongit.freedesktop.org/drm/drm-intel into drm-next - Fix GPU hang on MacBook2,1 when booting in EFI mode (Bugzilla #105637) - Fix garbled console on Y tiled BIOS framebuffer configs (Bugzilla #108264) - Fix black screen on certain eDP panels eg. Dell XPS 9350 (Bugzilla #107489 and #105338) - MST fixes that Rodrigo dropped from drm-intel-fixes and bunch of Icelake fixes - Then assorted proactive code fixes caught by CI or developers Signed-off-by:
Dave Airlie <airlied@redhat.com> From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181018165725.GA2281@jlahtine-desk.ger.corp.intel.com
-
- 18 Oct, 2018 17 commits
-
-
Anusha Srivatsa authored
Add missing MODULE_FIRMWARE while loading DMC ICL. v2: Add Fixes tag. (Rodrigo) v3: Rebase by Rodrigo after commit 7fe78985 ("drm/i915/csr: restructure CSR firmware definition macros") v4: Rodrigo fixing his own mess on commit mentioning on v3 comment above. Fixes: 4445930f ("firmware/dmc/icl: load v1.07 on icelake.") Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Signed-off-by:
Anusha Srivatsa <anusha.srivatsa@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> (v2) Signed-off-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Tested-by:
Paulo Zanoni <paulo.r.zanoni@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181004223613.19938-1-rodrigo.vivi@intel.com (cherry picked from commit 00e5d8b1) Signed-off-by:
Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
-
Rodrigo Vivi authored
Since when it was introduced we forgot to add this case so ICL was using a wrong signal_levels as reference. Fixes: fb5c8e9d ("drm/i915/icl: Implement voltage swing programming sequence for Combo PHY DDI") Cc: José Roberto de Souza <jose.souza@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Signed-off-by:
Manasi Navare <manasi.d.navare@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181017215652.26841-1-rodrigo.vivi@intel.com (cherry picked from commit 61cdfb9e) Signed-off-by:
-
Mahesh Kumar authored
DDI/TC clock-off bits are not equally distanced. TC1-3 bits are from offset 12 & TC4 is at offset 21. Create a function to choose correct clk-off bit. v2: Add fixes tag (Lucas) Fixes: c27e917e ("drm/i915/icl: add basic support for the ICL clocks") Signed-off-by:
Mahesh Kumar <mahesh1.kumar@intel.com> Signed-off-by:
Vandita Kulkarni <vandita.kulkarni@intel.com> Reviewed-by:
Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by:
-
Mahesh Kumar authored
This patch creates a function/wrapper to check if port is combophy port instead of explicitly comparing ports. Changes since V1: - keep all intel_port_is_* helper together (Lucas) Signed-off-by:
-
git://people.freedesktop.org/~agd5f/linuxDave Airlie authored
Fixes for 4.20. Highlights: - VCN DPG fixes for Picasso - Add support for the latest vega20 vbios - Scheduler timeout fix - License fixes for radeon and amdgpu - Misc other fixes Signed-off-by:
-
Dave Airlie authored
Merge tag 'drm-misc-next-fixes-2018-10-17' of git://anongit.freedesktop.org/drm/drm-misc into drm-next - Add quirk to fix orientation of Acer One 10 (S1003) panel (Hans) Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Imre Deak authored
If BIOS configured a Y tiled FB we failed to set up the backing object tiling accordingly, leading to a lack of GT fence installed and a garbled console. The problem was bisected to commit 011f22eb ("drm/i915: Do NOT skip the first 4k of stolen memory for pre-allocated buffers v2") but it just revealed a pre-existing issue. Kudos to Ville who suspected a missing fence looking at the corruption on the screen. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: <ronald@innovation.ch> Cc: <stable@vger.kernel.org> Reported-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Reported-by: <ronald@innovation.ch> Tested-by: <ronald@innovation.ch> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108264 Fixes: bc8d7dff ("drm/i915/skl: Provide a Skylake version of get_plane_config()") Signed-off-by:
Imre Deak <imre.deak@intel.com> Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181016160011.28347-1-imre.deak@intel.com (cherry picked from commit 914a4fd8) Signed-off-by:
-
Chris Wilson authored
Handle integer overflow when computing the sub-page length for shmem backed pread/pwrite. Reported-by:
Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: stable@vger.kernel.org Reviewed-by:
-
Chris Wilson authored
For mmap-exhaustion, we deliberately put the system under a large amount of pressure to ensure that we are able to reap mmap-offsets from dead objects. If background activity does that reaping for us, that defeats the purpose of the test and in some cases will fail our sanity checks (because of the fake activity we use to prevent the idle worker). Fixes: 932cac10 ("drm/i915/selftests: Prevent background reaping of acti ve objects") Signed-off-by:
Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181011103748.18387-1-chris@chris-wilson.co.uk (cherry picked from commit 0b4bf7ca) Signed-off-by:
-
Manasi Navare authored
This patch fixes the original commit c0cfb10d ("drm/i915/edp: Do not do link training fallback or prune modes on EDP") that causes a blank screen in case of certain eDP panels (Eg: seen on Dell XPS13 9350) where first link training fails and a retraining is required by falling back to lower link rate/lane count. In case of some panels they advertise higher link rate/lane count than whats required for supporting the panel's native mode. But we always link train at highest link rate/lane count for eDP and if that fails we can still fallback to lower link rate/lane count as long as the fallback link BW still fits the native mode to avoid pruning the panel's native mode yet retraining at fallback values to recover from a blank screen. v3: * Add const for fixed_mode (Ville) v2: * Send uevent if link failure on eDP unconditionally Fixes: c0cfb10d ("drm/i915/edp: Do not do link training fallback or prune modes on EDP") Cc: Clinton Taylor <clinton.a.taylor@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: <stable@vger.kernel.org> # v4.17+ Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107489 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105338Signed-off-by:
Alexander Wilson <alexander.wilson@ncf.edu> Reviewed-by:
-
Lyude Paul authored
Currently, i915 appears to rely on blocking modesets on no-longer-present MSTB ports by simply returning NULL for ->best_encoder(), which in turn causes any new atomic commits that don't disable the CRTC to fail. This is wrong however, since we still want to allow userspace to disable CRTCs on no-longer-present MSTB ports by changing the DPMS state to off and this still requires that we retrieve an encoder. So, fix this by always returning a valid encoder regardless of the state of the MST port. Changes since v1: - Remove mst atomic helper, since this got replaced with a much simpler solution Signed-off-by:
Lyude Paul <lyude@redhat.com> Reviewed-by:
-
Lyude Paul authored
Since we need to be able to allow DPMS on->off prop changes after an MST port has disappeared from the system, we need to be able to make sure we can compute a config for the resulting atomic commit. Currently this is impossible when the port has disappeared, since the VCPI slot searching we try to do in intel_dp_mst_compute_config() will fail with -EINVAL. Since the only commits we want to allow on no-longer-present MST ports are ones that shut off display hardware, we already know that no VCPI allocations are needed. So, hardcode the VCPI slot count to 0 when intel_dp_mst_compute_config() is called on an MST port that's gone. Changes since V4: - Don't use mst_port_gone at all, just check whether or not the drm connector is registered - Daniel Vetter Signed-off-by:
-
Lyude Paul authored
Currently we set intel_connector->mst_port to NULL to signify that the MST port has been removed from the system so that we can prevent further action on the port such as connector probes, mode probing, etc. However, we're going to need access to intel_connector->mst_port in order to fixup ->best_encoder() so that it can always return the correct encoder for an MST port to prevent legacy DPMS prop changes from failing. This should be safe, so instead keep intel_connector->mst_port always set and instead just check the status of drm_connector->regustered to signify whether or not the connector has disappeared from the system. Changes since v2: - Add a comment to mst_port_gone (Jani Nikula) - Change mst_port_gone to a u8 instead of a bool, per the kernel bot. Apparently bool is discouraged in structs these days Changes since v4: - Don't use mst_port_gone at all! Just check if the connector is registered or not - Daniel Vetter Signed-off-by:
-
Chris Wilson authored
Before we can reset the seqno, we have to be sure the engines are idle. In debugfs/i915_drop_caches_set, we do wait_for_idle but allow ourselves to be interrupted. We should only proceed to reset the seqno then if we were not interrupted, and so also avoid overwriting the error status. References: https://bugs.freedesktop.org/show_bug.cgi?id=108133 Fixes: 6b048706 ("drm/i915: Forcibly flush unwanted requests in drop-caches") Signed-off-by:
-
Ville Syrjälä authored
When we decide that a plane is attached to the wrong pipe we try to turn off said plane. However we are passing around the crtc we think that the plane is supposed to be using rather than the crtc it is currently using. That doesn't work all that well because we may have to do vblank waits etc. and the other pipe might not even be enabled here. So let's pass the plane's current crtc to intel_plane_disable_noatomic() so that it can its job correctly. To do that semi-cleanly we also have to change the plane readout to record the plane's visibility into the bitmasks of the crtc where the plane is currently enabled rather than to the crtc we want to use for the plane. One caveat here is that our active_planes bitmask will get confused if both planes are enabled on the same pipe. Fortunately we can use plane_mask to reconstruct active_planes sufficiently since plane_mask still has the same meaning (is the plane visible?) during readout. We also have to do the same during the initial plane readout as the second plane could clear the active_planes bit the first plane had already set. v2: Rely on fixup_active_planes() to populate active_planes fully (Daniel) Add Daniel's proposed comment to better document why we do this Drop the redundant intel_set_plane_visible() call Cc: stable@vger.kernel.org # fcba862e8428 drm/i915: Have plane->get_hw_state() return the current pipe Cc: stable@vger.kernel.org Cc: Dennis <dennis.nezic@utoronto.ca> Cc: Daniel Vetter <daniel@ffwll.ch> Tested-by:Dennis <dennis.nezic@utoronto.ca> Tested-by:
Peter Nowee <peter.nowee@gmail.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105637 Fixes: b1e01595 ("drm/i915: Redo plane sanitation during readout") Signed-off-by:
-
Ville Syrjälä authored
Plane sanitation needs vblank interrupts (on account of CxSR disable). So let's restore vblank interrupts earlier. v2: Make it actually build v3: Add comment to explain why we need this (Daniel) Cc: stable@vger.kernel.org Cc: Dennis <dennis.nezic@utoronto.ca> Tested-by:
-
Ville Syrjälä authored
commit 4e0b83a5 ("drm/i915: Extract per-platform plane->check() functions") removed the plane max stride check for sprite planes. I was going to add it back when introducing GTT remapping for the display, but after further thought it seems better to re-introduce it separately. So let's add the max stride check back. And let's do it in a nicer form than what we had before and do it for all plane types (easy now that we have the ->max_stride() plane vfunc). Only sprite planes really need this for now since primary planes are capable of scanning out the current max fb size we allow, and cursors have more stringent stride checks elsewhere. Cc: José Roberto de Souza <jose.souza@intel.com> Fixes: 4e0b83a5 ("drm/i915: Extract per-platform plane->check() functions") Signed-off-by:
Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> (cherry picked from commit fc3fed5d) Signed-off-by:
-
- 17 Oct, 2018 2 commits
-
-
James Zhu authored
ret_code should be initialized with 0. The check of read/write ptr should be activate when UVD_POWER_STATUS_TILES is off. Signed-off-by:
James Zhu <James.Zhu@amd.com> Acked-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Hans de Goede authored
The Acer One 10 uses a clamshell design with a detachable keyboard. As such in normal operating mode, with the keyboard attach the device is in landscape mode (and the Acer logo at boot also shows in landscape mode). But the device uses a portrait screen rotated 90 degrees (sigh). This commit adds a quirk for this device so that we shown the fbcon the right way up and that we hint userspace to also show e.g. plymouth and gdm the right way up. Cc: stable@vger.kernel.org Acked-by:
Hans de Goede <hdegoede@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181012101610.29100-1-hdegoede@redhat.com
-
- 16 Oct, 2018 6 commits
-
-
Dan Carpenter authored
The error handling is wrong and "ent" could be NULL we when dereference it to get "ent->d_inode". The thing is that normally debugfs_create_file() is not supposed to require (or have) any error handling. That function does return error pointers if debugfs is turned off but we know it's enable here. When it's enabled, then it returns NULL on error. So what I did was I stripped out all the error handling except around the i_size_write(). I could have just used a NULL check instead of an IS_ERR_OR_NULL() but I figured this was more clear because that way you don't have to look at the surrounding code to see whether debugfs is enabled or not. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
Feifei Xu authored
Add mmDB_DEBUG3 settings. Signed-off-by:
Feifei Xu <Feifei.Xu@amd.com> Reviewed-by:
Evan Quan <evan.quan@amd.com> Signed-off-by:
-
Evan Quan authored
Update the PPtable structure to fit the latest SMC firmware. Signed-off-by:
-
Evan Quan authored
PPTABLE structure is stretched to add I2C controller configuration. Hold on the PPTABLE_V20_SMU_VERSION bump until the VBIOS is ready. Signed-off-by:
-
Evan Quan authored
Update SDMA golden settings. Signed-off-by:
-
Rex Zhu authored
fix a typo in for loop: i->j Reviewed-by:
Rex Zhu <Rex.Zhu@amd.com> Signed-off-by:
-
- 15 Oct, 2018 3 commits
-
-
Su Sung Chung authored
[Why] A loop inside of build_evenly_distributed_points function that traverse through the array of points become an infinite loop when m_GammaUpdates does not get assigned to any value. [How] In DMColor, clear m_gammaIsValid bit just before writting all Zeromem for m_GammaUpdates, to prevent calling build_evenly_distributed_points before m_GammaUpdates gets assigned to some value. Signed-off-by:
Su Sung Chung <Su.Chung@amd.com> Reviewed-by:
Aric Cyr <Aric.Cyr@amd.com> Acked-by:
Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by:
-
Jonathan Gray authored
Commit b2441318 added "SPDX-License-Identifier: GPL-2.0" to files which previously had no license, change this to MIT for radeon matching the license text of the other radeon files. Signed-off-by:
Jonathan Gray <jsg@jsg.id.au> Signed-off-by:
-
Jonathan Gray authored
Commit b2441318 'License cleanup: add SPDX GPL-2.0 license identifier to files with no license' incorrectly added "SPDX-License-Identifier: GPL-2.0" to a file with MIT license text. Change the SPDX identifier to match the license text. Signed-off-by:
-
- 12 Oct, 2018 6 commits
-
-
James Zhu authored
Update Static Power Gate mode UVD status clear Signed-off-by:
Leo Liu <leo.liu@amd.com> Acked-by:
-
James Zhu authored
Set VCPU busy after gate power during vcn Static Power Gate start Signed-off-by:
-
James Zhu authored
Apply new UMC enable for VNC Dynamic Power Gate mode Signed-off-by:
-
James Zhu authored
Remove Sitatic Power Gate mode unused steps during vcn start Signed-off-by:
-
James Zhu authored
Add Static Power Gate mode Register XX check Signed-off-by:
-
James Zhu authored
Move Static Power Gate mode mc resume after MPC control Signed-off-by:
-
