- 23 Sep, 2009 40 commits
-
-
KAMEZAWA Hiroyuki authored
Presently, kclist_add() only eats start address and size as its arguments. Considering to make kclist dynamically reconfigulable, it's necessary to know which kclists are for System RAM and which are not. This patch add kclist types as KCORE_RAM KCORE_VMALLOC KCORE_TEXT KCORE_OTHER This "type" is used in a patch following this for detecting KCORE_RAM. Signed-off-by:
KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: WANG Cong <xiyou.wangcong@gmail.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
KAMEZAWA Hiroyuki authored
This patchset is for /proc/kcore. With this, - many per-arch hooks are removed. - /proc/kcore will know really valid physical memory area. - /proc/kcore will be aware of memory hotplug. - /proc/kcore will be architecture independent i.e. if an arch supports CONFIG_MMU, it can use /proc/kcore. (if the arch uses usual memory layout.) This patch: /proc/kcore uses its own list handling codes. It's better to use generic list codes. No changes in logic. just clean up. Signed-off-by:
-
Stefani Seibold authored
A patch to give a better overview of the userland application stack usage, especially for embedded linux. Currently you are only able to dump the main process/thread stack usage which is showed in /proc/pid/status by the "VmStk" Value. But you get no information about the consumed stack memory of the the threads. There is an enhancement in the /proc/<pid>/{task/*,}/*maps and which marks the vm mapping where the thread stack pointer reside with "[thread stack xxxxxxxx]". xxxxxxxx is the maximum size of stack. This is a value information, because libpthread doesn't set the start of the stack to the top of the mapped area, depending of the pthread usage. A sample output of /proc/<pid>/task/<tid>/maps looks like: 08048000-08049000 r-xp 00000000 03:00 8312 /opt/z 08049000-0804a000 rw-p 00001000 03:00 8312 /opt/z 0804a000-0806b000 rw-p 00000000 00:00 0 [heap] a7d12000-a7d13000 ---p 00000000 00:00 0 a7d13000-a7f13000 rw-p 00000000 00:00 0 [thread stack: 001ff4b4] a7f13000-a7f14000 ---p 00000000 00:00 0 a7f14000-a7f36000 rw-p 00000000 00:00 0 a7f36000-a8069000 r-xp 00000000 03:00 4222 /lib/libc.so.6 a8069000-a806b000 r--p 00133000 03:00 4222 /lib/libc.so.6 a806b000-a806c000 rw-p 00135000 03:00 4222 /lib/libc.so.6 a806c000-a806f000 rw-p 00000000 00:00 0 a806f000-a8083000 r-xp 00000000 03:00 14462 /lib/libpthread.so.0 a8083000-a8084000 r--p 00013000 03:00 14462 /lib/libpthread.so.0 a8084000-a8085000 rw-p 00014000 03:00 14462 /lib/libpthread.so.0 a8085000-a8088000 rw-p 00000000 00:00 0 a8088000-a80a4000 r-xp 00000000 03:00 8317 /lib/ld-linux.so.2 a80a4000-a80a5000 r--p 0001b000 03:00 8317 /lib/ld-linux.so.2 a80a5000-a80a6000 rw-p 0001c000 03:00 8317 /lib/ld-linux.so.2 afaf5000-afb0a000 rw-p 00000000 00:00 0 [stack] ffffe000-fffff000 r-xp 00000000 00:00 0 [vdso] Also there is a new entry "stack usage" in /proc/<pid>/{task/*,}/status which will you give the current stack usage in kb. A sample output of /proc/self/status looks like: Name: cat State: R (running) Tgid: 507 Pid: 507 . . . CapBnd: fffffffffffffeff voluntary_ctxt_switches: 0 nonvoluntary_ctxt_switches: 0 Stack usage: 12 kB I also fixed stack base address in /proc/<pid>/{task/*,}/stat to the base address of the associated thread stack and not the one of the main process. This makes more sense. [akpm@linux-foundation.org: fs/proc/array.c now needs walk_page_range()] Signed-off-by:Stefani Seibold <stefani@seibold.net> Cc: Ingo Molnar <mingo@elte.hu> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
Vincent Li authored
Remove obfuscated zero-length input check and return -EINVAL instead of -EIO error to make the error message clear to user. Add whitespace stripping. No functionality changes. The old code: echo 1 > /proc/pid/make-it-fail (ok) echo 1foo > /proc/pid/make-it-fail (-bash: echo: write error: Input/output error) The new code: echo 1 > /proc/pid/make-it-fail (ok) echo 1foo > /proc/pid/make-it-fail (-bash: echo: write error: Invalid argument) This patch is conservative in changes to not breaking existing scripts/applications. Signed-off-by:
Vincent Li <macli@brc.ubc.ca> Signed-off-by:
-
Vincent Li authored
Andrew Morton pointed out similar string hacking and obfuscated check for zero-length input at the end of the function, David Rientjes suggested to use strict_strtol to replace simple_strtol, this patch cover above suggestions, add removing of leading and trailing whitespace from user input. It does not change function behavious. Signed-off-by:
David Rientjes <rientjes@google.com> Cc: Matt Mackall <mpm@selenic.com> Cc: Amerigo Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Amerigo Wang authored
In 9063c61f ("x86, 64-bit: Clean up user address masking") Linus fixed the wrong size of /proc/kcore problem. But its size still looks insane, since it never equals the size of physical memory. Signed-off-by:
WANG Cong <amwang@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Tao Ma <tao.ma@oracle.com> Cc: <mtk.manpages@gmail.com> Acked-by:
-
Oleg Nesterov authored
The exiting sub-thread flushes /proc/pid only, but this doesn't buy too much: ps and friends mostly use /proc/tid/task/pid. Remove "if (thread_group_leader())" checks from proc_flush_task() path, this means we always remove /proc/tid/task/pid dentry on exit, and this actually matches the comment above proc_flush_task(). The test-case: static void* tfunc(void *arg) { char name[256]; sprintf(name, "/proc/%d/task/%ld/status", getpid(), gettid()); close(open(name, O_RDONLY)); return NULL; } int main(void) { pthread_t t; for (;;) { if (!pthread_create(&t, NULL, &tfunc, NULL)) pthread_join(t, NULL); } } slabtop shows that pid/proc_inode_cache/etc grow quickly and "indefinitely" until the task is killed or shrink_slab() is called, not good. And the main thread needs a lot of time to exit. The same can happen if something like "ps -efL" runs continuously, while some application spawns short-living threads. Reported-by:"James M. Leddy" <jleddy@redhat.com> Signed-off-by:
Oleg Nesterov <oleg@redhat.com> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Dominic Duval <dduval@redhat.com> Cc: Frank Hirtz <fhirtz@redhat.com> Cc: "Fuller, Johnray" <Johnray.Fuller@gs.com> Cc: Larry Woodman <lwoodman@redhat.com> Cc: Paul Batkowski <pbatkowski@redhat.com> Cc: Roland McGrath <roland@redhat.com> Signed-off-by:
-
Kees Cook authored
/proc/$pid/limits should show RLIMIT_CPU as seconds, which is the unit used in kernel/posix-cpu-timers.c: unsigned long psecs = cputime_to_secs(ptime); ... if (psecs >= sig->rlim[RLIMIT_CPU].rlim_max) { ... __group_send_sig_info(SIGKILL, SEND_SIG_PRIV, tsk); Signed-off-by:Kees Cook <kees.cook@canonical.com> Acked-by:
WANG Cong <xiyou.wangcong@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Chris Ball authored
On an OLPC XO-1.5 development board with Via VX855 chipset, the sdhci controller can take up to 12ms to stabilize its clock, but the current timeout at which we give up on the controller is 10ms. The patch increases the timeout delay rather than using a device-specific quirk -- since we exit the loop when the clock comes up, increasing the timeout value will only make us mdelay() longer in the errant case of a device with a clock that is not stabilizing, which it seems worth waiting a little longer for in general. Signed-off-by:
Chris Ball <cjb@laptop.org> Cc: Harald Welte <HaraldWelte@viatech.com> Acked-by:
Pierre Ossman <pierre@ossman.eu> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
Richard Röjfors authored
Add support for ADMA on SDHCI hosts, not supporting SDMA. According to the SDHCI specifications a host can support ADMA but not SDMA Signed-off-by:
Richard Röjfors <richard.rojfors@mocean-labs.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
Nicolas Pitre authored
Especially with the PM framework, those are quite handy to have in driver code too. Signed-off-by:
Nicolas Pitre <nico@marvell.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
Nicolas Pitre authored
Especially for SDIO drivers which may have special conditions/errors to report, it is a good thing to relay the returned error code back to upper layers. This also allows for the rationalization of the resume path where code to "remove" a no-longer-existing or replaced card was duplicated into the MMC, SD and SDIO bus drivers. In the SDIO case, if a function suspend method returns an error, then all previously suspended functions are resumed and the error returned. An exception is made for -ENOSYS which the core interprets as "we don't support suspend so just kick the card out for suspend and return success". When resuming SDIO cards, the core code only validates the manufacturer and product IDs to make sure the same kind of card is still present before invoking functions resume methods. It's the function driver's responsibility to perform further tests to confirm that the actual same card is present (same MAC address, etc.) and return an error otherwise. Signed-off-by:
-
Nicolas Pitre authored
Currently, all SDIO cards are virtually removed upon a suspend, and completely reprobed upon a resume. This adds the suspend and resume methods to the SDIO bus driver so to be able to dispatch those events to the actual SDIO function drivers for real suspend/resume instead. All active functions on a card must have a driver with both a suspend and a resume method though. Failing that, we fall back to the current behavior of simply "removing" the card when suspending. When resuming, we make sure the same card is still inserted by comparing the vendor and product IDs. If there is a mismatch, or if there is simply no card anymore in the slot, then the previous card is "removed" and the new card is detected. This is further enhanced with the next patch. [akpm@linux-foundation.org: fix warnings] Signed-off-by:
-
Wolfgang Muees authored
Some time ago, I have send a patch to the mmc_spi subsystem changing the error codes. This was after a discussion with Pierre about using EINVAL only for non-recoverable errors. This patch was accepted as http://git.kernel.org/linus/fdd858db7113ca64132de390188d7ca00701013d Unfortunately, several weeks later, I realized that this patch has opened a little can of worms because there are SD cards on the market which a) claim that they support the switch command AND b) refuse to execute this command if operating in SPI mode. So, such a card would get unusuable in an embedded linux system in SPI mode, because the init sequence terminates with an error. This patch adds the missing error codes to the caller of the switch command and restores the old behaviour to fail gracefully if these commands can not execute. Signed-off-by:
Wolfgang Muees <wolfgang.mues@auerswald.de> Cc: <linux-mmc@vger.kernel.org> Cc: <stable@kernel.org> [2.6.31.x] Signed-off-by:
-
kishore kadiyala authored
Add basic support for all 5 MMC controllers on OMAP4. This patch doesn't include mmc-regulator support Signed-off-by:
Kishore Kadiyala <kishore.kadiyala@ti.com> Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com> Acked-by:
Madhusudhan Chikkature <madhu.cr@ti.com> Cc: Russell King <linux@arm.linux.org.uk> Acked-by:
Tony Lindgren <tony@atomide.com> Cc: Hiroshi DOYU <Hiroshi.DOYU@nokia.com> Cc: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
Chris Ball authored
Card insertion detection is broken without this quirk on a Sony Vaio Z11, as discussed on linux-mmc here: http://marc.info/?t=125017355000008Signed-off-by:
Norbert Preining <preining@logic.at> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
Rob Emanuele authored
Created a modified version of the at91sam9g20 evaluation kit platform (board-sam9g20ek-2slot-mmc.c) and device support to make use of the updated atmel-mci driver. As the use of two slots modify GPIO pin allocation, we create another board file. This requires getting the most updated arch/arm/tools/mach-types from http://www.arm.linux.org.uk/developer/machines/download.php to have the machine type for the at91sam9g20ek-2slot-mmc board. [nicolas.ferre@atmel.com: printk, slot_count modification in at91sam9260_devices.c file] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by:
Rob Emanuele <rob@emanuele.us> Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Andrew Victor <linux@maxim.org.za> Cc: Russell King <rmk@arm.linux.org.uk> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
Rob Emanuele authored
Unification of the atmel-mci driver to support the AT91 processors MCI interface. The atmel-mci driver currently supports the AVR32 and this patch adds AT91 support. Add read/write proof selection switch dependent on chip availability of this feature. To use this new driver on a at91 the platform driver for your board needs to be updated. [nicolas.ferre@atmel.com indent, Kconfig comment and one printk modification] Signed-off-by:
-
Ohad Ben-Cohen authored
Normally writes to SDIO function 0 outside the vendor specific CCCR registers are prohibited. To support embedded devices that require writes to SDIO function 0 outside this range (e.g. TI WL127x embedded sdio wifi device), MMC_QUIRK_LENIENT_FN0 is introduced. A card quirks field is added to `struct mmc_card' to support non-standard devices (e.g. embedded sdio devices). [akpm@linux-foundation.org: code in C, not cpp!] Signed-off-by:
Ohad Ben-Cohen <ohad@wizery.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
Anton Vorontsov authored
- Get rid of incomprehensible "if { for { if } }" construction for the exponential divisor calculation. The first if statement isn't correct at all, since it should check for "host->max_clk / pre_div / 16 > clock". The error doesn't cause any bugs because the check in the for loop does the right thing, and so the outer check becomes useless; - For the linear divisor do the same: a single while statement is more readable than for + if construction; - Add dev_dbg() that prints desired and actual clock frequency. Signed-off-by:Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Pierre Ossman <pierre@ossman.eu> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: David Vrabel <david.vrabel@csr.com> Cc: Ben Dooks <ben@fluff.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
Anton Vorontsov authored
MPC85xx SOCs have normal write-protect state reporting, so we shouldn't hard-code the quirk. Instead, look for "sdhci,wp-inverted" property, plus check for mpc837x_{rdb,mds} machines since older device trees don't specify the new property. Signed-off-by: -
Anton Vorontsov authored
eSDHC block in MPC837x SOCs reports inverted write-protect state, soon sdhci-of driver will look for sdhci,wp-inverted properties to decide whether apply a specific quirk. So, document the property and add it to device tree source files. Signed-off-by:
-
Anton Vorontsov authored
eSDHC fails to recognize some SDHS cards, throwing timeout errors: mmc0: error -110 whilst initialising SD card That's because we calculate timeout value in a wrong way: on eSDHC hosts the timeout clock is derivied from the SD clock, which is set dynamically. As David Vrabel suggested, deriving timeout clock from SD clock is a common scheme, so let's implement DATA_TIMEOUT_USES_SDCLK quirk and use it for eSDHC hosts. Also, from now on we don't need esdhc_get_timeout_clock() callback, so remove it. Signed-off-by:
-
Anton Vorontsov authored
SDHCI core tries to write HISPD bit into the host control register, but the eSDHC controllers don't have that bit, and that causes all sorts of misbehaviour when using 4-bit mode capable SD cards. Signed-off-by:
-
Anton Vorontsov authored
Linear divisor's values in a register start at 0 (zero means "divide by 1"). Before this patch the code didn't account that fact, so SD cards were running underclocked. Signed-off-by:
-
Roel Kluin authored
Avoid buffer underrun when parsing an invalid CISTPL_VERS_1. Signed-off-by:
Roel Kluin <roel.kluin@gmail.com> Cc: David Vrabel <david.vrabel@csr.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
Anton Vorontsov authored
get_min_clock() makes sense only with NONSTANDARD_CLOCK quirk and when set_clock() callback is specified. The patch should cause no functional changes, it just makes the code self-documented and avoids any possible misuse of get_min_clock(). Suggested-by:
-
Ohad Ben-Cohen authored
Add support to disconnect the pull-up resistor on CD/DAT[3] (pin 1) of the card. This may be desired on certain setups of boards, controllers and embedded sdio devices which do not need the card's pull-up. As a result, card detection is disabled and power is saved. [akpm@linux-foundation.org: simplify sdio_disable_cd() a bit] Signed-off-by:
Matt Fleming <matt@console-pimps.org> Cc: Ian Molton <ian@mnementh.co.uk> Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com> Cc: Philip Langdale <philipl@overt.org> Cc: Pierre Ossman <pierre@ossman.eu> Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by:
-
Madhusudhan Chikkature authored
Update maintainers entry for TI OMAP HS MMC support. Signed-off-by:
Kevin Hilman <khilman@deeprootsystems.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
Adrian Hunter authored
Specify MMC capabilities and set the power-saving flag for RX51. Signed-off-by:
Adrian Hunter <adrian.hunter@nokia.com> Acked-by:
-
Adrian Hunter authored
Commands like SWITCH (CMD6) send a response and then signal busy while the operation is completed. These commands are expected to always succeed (otherwise the response would have indicated an error). Set an arbitrarily large data timeout value (100ms) for these commands to ensure that premature timeouts do not occur. Signed-off-by:
-
Adrian Hunter authored
[madhu.cr@ti.com: fix for the db clock failure message] Signed-off-by:
-
Adrian Hunter authored
Depending on the manufacturer, there is a small possibility that removing a card while it is being written to, can render the card permanently unusable. To prevent that, the card is made inaccessible when the cover is open. Signed-off-by:
-
Denis Karpov authored
Functions', structures', variables' names are changed to start with omap_hsmmc_ prefix. Signed-off-by:
Denis Karpov <ext-denis.2.karpov@nokia.com> Signed-off-by:
-
Adrian Hunter authored
If an unexpected interrupt occurs while preparing the next request, an oops can occur. For example, a new request is setting up DMA for data transfer so host->data is not NULL. An unexpected transfer complete (TC) interrupt comes along and the interrupt handler sets host->data to NULL. Oops! Prevent that by adding a spinlock. Signed-off-by:
-
Adrian Hunter authored
Sometimes the controller unexpectedly produces a TC (transfer complete) interrupt before the CC (command complete) interrupt for command 6 (SWITCH). This is a problem because the CC interrupt can get mixed up with the next request. Add a hack for CMD6. Signed-off-by:
-
Adrian Hunter authored
Clear the interrupt status after sending the initialization sequence, as specified in the TRM. Signed-off-by:
-
Denis Karpov authored
Use macro mmc_slot() in omap_hsmmc. Signed-off-by:
-
Jarkko Lavinen authored
Do not call 'mmc_omap_xfer_done()' if the request is already done. Signed-off-by:
Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by:
-
Jarkko Lavinen authored
After 1 second of inactivity, put card and/or regulator to sleep. After 8 seconds of inactivity, turn off the power. Signed-off-by:
-
