This patch adds support for HS200 tuning mode on AMD eMMC-4.5.1
Reviewed-by: Sen, Pankaj <Pankaj.Sen@amd.com>
Reviewed-by: Shah, Nehal-bakulchandra <Nehal-bakulchandra.Shah@amd.com>
Reviewed-by: Agrawal, Nitesh-kumar <Nitesh-kumar.Agrawal@amd.com>
Signed-off-by: S-k, Shyam-sundar <Shyam-sundar.S-k@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The mxcmmc platform data header depends on interrupt.h. Don't rely on the
public mmc header host.h to include it, bud instead make that dependency
explicit.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It's unnecessary to check the irqs_queued value as
it always needs to queue one if irq isn't enabled.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Per SDIO Simplified Specification V3, section 3.1.2, A host that
supports UHS-I sets S18R to 1 in the argument of CMD5 to request a
change of the signal voltage to 1.8V. If the card supports UHS-I and
the current signal voltage is 3.3V, S18A is set to 1 in the R4 response.
If the signal voltage is already 1.8V, the card sets S18A to 0 so that
host maintains the current signal voltage. UHS-I is supported in SD mode
and S18A is always 0 in SPI mode.

For the current code, if the signaling voltage is fixed 1.8v, so
the card will set S18A to 0 for rocr and thus we would clear the
R4_18V_PRESENT from ocr, which make core won't try to use uhs mode.

To fix it, we expect sdio_read_cccr would fail if the uhs mode won't
work at all. Note that it's interesting that some sdio cards still
response S18A even the voltage is fixed to 1.8v and the CMD11 will
also accepted and finish enabling UHS mode successfully. I guess this
is why folks didn't notice this problem. Anyway, fix it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add new helper function, mmc_sdio_resend_if_cond, to be
reused when trying to retry the init sequence.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

* A multiplication for the size determination of a memory allocation
  indicated that an array data structure should be processed.
  Thus use the corresponding function "kmalloc_array".

  This issue was detected by using the Coccinelle software.

* Replace the specification of a data structure by a pointer dereference
  to make the corresponding size determination a bit safer according to
  the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

* The script "checkpatch.pl" pointed information out like the following.

  WARNING: Prefer kcalloc over kzalloc with multiply

  Thus fix the affected source code place.

* Replace the specification of a data structure by a pointer dereference
  to make the corresponding size determination a bit safer according to
  the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The script "checkpatch.pl" pointed information out like the following.

WARNING: quoted string split across lines

Thus fix affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use space characters at some source code places according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The script "checkpatch.pl" pointed information out like the following.

WARNING: Prefer seq_puts to seq_printf

Thus fix the affected source code place.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add a missing character in the function description.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

* A multiplication for the size determination of a memory allocation
  indicated that an array data structure should be processed.
  Thus use the corresponding function "kmalloc_array".

  This issue was detected by using the Coccinelle software.

* Replace the specification of a data structure by a pointer dereference
  to make the corresponding size determination a bit safer according to
  the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The probe exit path on error does nothing since commit 94b110af
("mmc: tmio: add tmio_mmc_host_alloc/free()"), so we can bail out
immediately.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The caller may supply connection ID, index, or both. All combinations are
possible and mmc framework should not make any assumption on what exactly
caller wants.

Remove con_id override conditionals in mmc_gpiod_request_ro() and
mmc_gpiod_request_cd().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

cd_con_id is not used and always NULL.
Remove it to make code a bit more cleaner.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

msdc_card_busy only need check if the data0 is low.
In sdio data1 irq mode, data1 may be low because of interruption.
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Initially all QorIQ platforms were PowerPC architecture and they didn't
support card detection except several platforms. The driver added the
quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION as default and this made broken-cd
property in dts node didn't work. Now QorIQ platform turns to ARM
architecture and most of them could support card detection. However it's
a large number of dts trees that need to be fixed with broken-cd if we
remove the default SDHCI_QUIRK_BROKEN_CARD_DETECTION in driver. And the
users don't want to see this. So this patch is to remove this default
quirk just for ARM and keep it for PowerPC.(Note, QorIQ PowerPC platform
only has big-endian eSDHC while QorIQ ARM platform has big-endian or
little-endian eSDHC) This makes broken-cd property work again for ARM.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The eSDHC register definitions in header file were messy and confusing.
This patch is to clean up these definitions.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This platform driver adds initial support for the DW host controller
found on ZTE SoCs.

It has been tested on ZX296718 EVB board currently. More support on
timing tuning will be added when hardware is available.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Document the device-tree binding of ZTE MMC host on
ZX296718 SoC.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Data done irq is expected if data length is less than
watermark in PIO mode. But fifo watermark is requested
to be aligned with data length in some SoC so that TX/RX
irq can be generated with data done irq. Add the
watermark alignment to mark this requirement and force
fifo watermark setting accordingly.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The FIFO address may break default address assumption of 0x100
(version < 0x240A) and 0x200(version >= 0x240A) in current driver.
The new property is introduced to override fifo address via DT
node information.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add fifo-addr property and fifo-watermark-quirk property to
synopsys-dw-mshc bindings. It is intended to provide more
dt interface to support SoCs specific configuration.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

An mmc host driver shouldn't rely on interrupt.h being included by another
public mmc header. Instead make that dependency explicit by including
interrupt.h in those host drivers that depends on it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Don't rely on host.h to include the leds.h header, but instead include it
explicitly because the driver depends on it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>

Don't rely on host.h to include the mmc.h header, but instead include it
explicitly because the driver depends on it.

Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>

There are currently no external users of the public dw_mmc header file,
except the dw_mmc driver itself. Therefore let's move the definitions from
the public dw_mmc header file into the existing private dw_mmc header file
and then remove the public one.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

There are currently no users of the clk_ctrl2_present member from the
platform data, so let's remove it.

Note, as some of the sh_mmcif variants may support clk_ctrl2, let's keep
the current code in the driver, which deals with this. For future support,
we should invent a DT binding instead, but let's leave that until it's
needed.

Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

There are currently no users of the ccs_unsupported member from the
platform data, so let's remove it.

Note, as some of the sh_mmcif variants may not support ccs, let's keep the
current code in the driver, which deals with this. For future support, we
should invent a DT binding instead, but let's leave that until it's needed.

Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Removing the callback also enables us to remove the sh_mmcif_get_cd()
altogether, as we convert to use mmc_gpio_get_cd() to the same kind of
work.

Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

The enum that specifies the MMC_PROGRESS* types, is a sh mmcif specific
thing and has no relevance in a public mmc header. Currently it's used only
by the sh romImage MMCIF boot, so let's instead define the enum in there
and rename the types to MMCIF_* to show this.

Cc: linux-sh@vger.kernel.org
Cc: Simon Horman <horms@verge.net.au>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

According to the BCM2835 datasheet the maximum block size for the
eMMC module is restricted to the internal data FIFO which is 1024 byte.
But this is still an improvement to the default of 512 byte.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Since the mmc module on bcm2835 neither provide a capabilities register nor
free documentation we must rely on the downstream implementation [1].

So enable the following capabilities for bcm2835:

MMC_CAP_MMC_HIGHSPEED
MMC_CAP_SD_HIGHSPEED
MMC_CAP_DRIVER_TYPE_A
MMC_CAP_DRIVER_TYPE_C

[1] - https://github.com/raspberrypi/linux/blob/rpi-4.4.y/drivers/mmc/host/bcm2835-mmc.cSigned-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In the MMC subsystem, we see such initializers that only clears the
first member explicitly.

For example,

  struct mmc_request mrq = {NULL};

sets the first member (.sbc) to NULL explicitly.  However, this is
an unstable form because we may insert a non-pointer member at the
top of the struct mmc_request in the future. (if we do so, the
compiler will spit warnings.)

So, using a designated initializer is preferred coding style.  The
expression above is equivalent to:

  struct mmc_request mrq = { .sbc = NULL };

Of course, this does not express our intention.  We want to fill
all struct members with zeros.  Please note struct members are
implicitly zero-cleared unless otherwise specified in the initializer.

After all, the most reasonable (and stable) form is:

  struct mmc_request mrq = {};

Do likewise for mmc_command, mmc_data as well.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

With gcc-4.1.2:

    mmc/core/block.c: In function ‘mmc_blk_issue_discard_rq’:
    mmc/core/block.c:1150: warning: ‘arg’ may be used uninitialized in this function
    mmc/core/block.c:1150: warning: ‘nr’ may be used uninitialized in this function
    mmc/core/block.c:1150: warning: ‘from’ may be used uninitialized in this function

While this is a false positive, it can be avoided easily by jumping over
the checks for "err" that are always false.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In the eMMC 5.0 version of the spec, several EXT_CSD fields about
device lifetime are added.

 - Two types of estimated indications reflected by averaged wear out of memory
 - An indication reflected by average reserved blocks

Export the information through sysfs.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>