- 22 Apr, 2021 26 commits
-
-
Artur Petrosyan authored
When core is in hibernation state and an external hub is connected, upper layer sends URB enqueue request, which results in port reset issue. - Added exit from hibernation state to avoid port reset issue and process upper layer request properly. Acked-by:
Minas Harutyunyan <Minas.Harutyunyan@synopsys.com> Signed-off-by:
Artur Petrosyan <Arthur.Petrosyan@synopsys.com> Link: https://lore.kernel.org/r/20210416124803.D1C1FA005F@mailhost.synopsys.comSigned-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Artur Petrosyan authored
This move is done to call hibernation exit handler in "dwc2_port_resume()" function when core receives port resume. Otherwise it could be confusing to exit hibernation in "dwc2_hcd_hub_control()" function but other power saving modes in "dwc2_port_resume()" function. Acked-by:
-
Artur Petrosyan authored
This move is done to call enter hibernation handler in "dwc2_port_suspend()" function when core receives port suspend. Otherwise it could be confusing to enter to hibernation in "dwc2_hcd_hub_control()" function but other power saving modes in "dwc2_port_suspend()" function. Acked-by:
-
Artur Petrosyan authored
When hibernation exit is performed the dwc2_hib_restore_common() function is called. In that function we wait until GINTSTS_RESTOREDONE bit is set. However, after the setting of that bit we get a lot of (dwc2_hsotg_irq:) interrupts which indicates that (GINTSTS.RstrDoneInt) restore done interrupt is asserted. To avoid restore done interrupt storm after restore is generated clear GINTSTS_RESTOREDONE bit in GINTSTS register. Acked-by:
-
Artur Petrosyan authored
Switching from device mode to host mode by disconnecting device cable core enters and exits form hibernation. However, the fifo map remains not cleared. It results to a WARNING (WARNING: CPU: 5 PID: 0 at drivers/usb/dwc2/ gadget.c:307 dwc2_hsotg_init_fifo+0x12/0x152 [dwc2]) if in host mode we disconnect the micro a to b host cable. Because core reset occurs. To avoid the WARNING, fifo_map should be cleared in dwc2_core_reset() function by taking into account configs. fifo_map must be cleared only if driver is configured in "CONFIG_USB_DWC2_PERIPHERAL" or "CONFIG_USB_DWC2_DUAL_ROLE" mode. - Added "static inline void dwc2_clear_fifo_map()" helper function to clear fifo_map with peripheral or dual role mode. - Added a dummy version of "dwc2_clear_fifo_map()" helper for host-only mode. Acked-by:
-
Artur Petrosyan authored
When device cable is disconnected core receives suspend interrupt and enters hibernation. After entering into hibernation GPWRDN_RST_DET and GPWRDN_STS_CHGINT interrupts are asserted. Allowed exit from gadget hibernation from GPWRDN_RST_DET by checking only linestate. Changed the return type of "dwc2_handle_gpwrdn_intr()" function from void to int because exit from hibernation functions have a return value. Acked-by:
-
Artur Petrosyan authored
When core is in hibernation in host mode and a device cable was connected then driver exited from device hibernation. However, registers saved for host mode and when exited from device hibernation register restore would be done for device register which was wrong because there was no device registers stored to restore. - Added dwc_handle_gpwrdn_disc_det() function which handles gpwrdn disconnect detect flow and exits hibernation without restoring the registers. - Updated exiting from hibernation in GPWRDN_STS_CHGINT with calling dwc_handle_gpwrdn_disc_det() function. Here no register is restored which is the solution described above. Fixes: 65c9c4c6 ("usb: dwc2: Add dwc2_handle_gpwrdn_intr() handler") Acked-by:
-
Artur Petrosyan authored
Added setting "port_connect_status_change" flag to "1" in order to re-enumerate, because after exit from hibernation port connection status is not detected. Fixes: c5c403dc ("usb: dwc2: Add host/device hibernation functions") Acked-by:
-
Artur Petrosyan authored
Initially resetting device address was done in dwc2_hsotg_irq() interrupt handler. However, when core is hibernated USB RESET is not handled in dwc2_hsotg_irq() handler, instead USB RESET interrupt is handled in dwc2_handle_gpwrdn_intr() handler. - Added reset device address to zero when core exits from gadget hibernation. Acked-by:
-
Artur Petrosyan authored
No need to check for "DWC2_POWER_DOWN_PARAM_HIBERNATION" param as "hsotg->hibernated" flag is already enough for exiting from hibernation mode. - Removes checking of "DWC2_POWER_DOWN_PARAM_HIBERNATION" param. - For code readability Hibernation exit code moved after debug message print. - Added "dwc2_exit_hibernation()" function error checking. Acked-by:
-
Greg Kroah-Hartman authored
Merge tag 'usb-serial-5.13-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next Johan writes: USB-serial updates for 5.13-rc1 Here are the USB-serial updates for 5.13-rc1, including: - better type detection for pl2303 - support for more line speeds for pl2303 (TA/TB) - fixed CSIZE handling for the new xr driver - core support for multi-interface functions - TIOCGSERIAL and TIOCSSERIAL fixes - generic TIOCSSERIAL support (e.g. for closing_wait) - fixed return value for unsupported ioctls - support for gpio valid masks in cp210x - drain-delay fixes and improvements - support for multi-port devices for xr - generalisation of the xr driver to support three new device classes (XR21B142X, XR21B1411 and XR2280X) Included are also various clean ups. All have been in linux-next with no reported issues. * tag 'usb-serial-5.13-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (72 commits) USB: cdc-acm: add more Maxlinear/Exar models to ignore list USB: serial: xr: add copyright notice USB: serial: xr: reset FIFOs on open USB: serial: xr: add support for XR22801, XR22802, XR22804 USB: serial: xr: add support for XR21B1411 USB: serial: xr: add support for XR21B1421, XR21B1422 and XR21B1424 USB: serial: xr: add type abstraction USB: serial: xr: drop type prefix from shared defines USB: serial: xr: move pin configuration to probe USB: serial: xr: rename GPIO-pin defines USB: serial: xr: rename GPIO-mode defines USB: serial: xr: add support for XR21V1412 and XR21V1414 USB: serial: ti_usb_3410_5052: clean up termios CSIZE handling USB: serial: ti_usb_3410_5052: use kernel types consistently USB: serial: ti_usb_3410_5052: add port-command helpers USB: serial: ti_usb_3410_5052: clean up vendor-request helpers USB: serial: ti_usb_3410_5052: drop unnecessary packed attributes USB: serial: io_ti: drop unnecessary packed attributes USB: serial: io_ti: use kernel types consistently USB: serial: io_ti: add read-port-command helper ...
-
Thinh Nguyen authored
The programming guide incorrectly stated that the DCFG.bInterval_m1 must be set to 0 when operating in fullspeed. There's no such limitation for all IPs. See DWC_usb3x programming guide section 3.2.2.1. Fixes: a1679af8 ("usb: dwc3: gadget: Fix setting of DEPCFG.bInterval_m1") Cc: <stable@vger.kernel.org> Acked-by:
Felipe Balbi <balbi@kernel.org> Signed-off-by:
Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/5d4139ae89d810eb0a2d8577fb096fc88e87bfab.1618472454.git.Thinh.Nguyen@synopsys.comSigned-off-by:
-
Chunfeng Yun authored
PM will take care of the status of child device, so no need check each port anymore. Suggested-by:
Ikjoon Jang <ikjn@chromium.org> Signed-off-by:
Chunfeng Yun <chunfeng.yun@mediatek.com> Link: https://lore.kernel.org/r/1618555706-6810-1-git-send-email-chunfeng.yun@mediatek.comSigned-off-by:
-
Badhri Jagan Sridharan authored
Allows PMIC charger loops which are slow(i.e. cannot meet the 15ms deadline) to still comply to pSnkStby i.e Maximum power that can be consumed by sink while in Sink Standby state as defined in 7.4.2 Sink Electrical Parameters of USB Power Delivery Specification Revision 3.0, Version 1.2. This patch introduces slow-charger-loop which when set makes the port request PD_P_SNK_STDBY_MW(2.5W i.e 500mA@5V) upon entering SNK_DISCOVERY (instead of 3A or the 1.5A during SNK_DISCOVERY) and the actual currrent limit after RX of PD_CTRL_PSRDY for PD link or during SNK_READY for non-pd link. Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Badhri Jagan Sridharan <badhri@google.com> Link: https://lore.kernel.org/r/20210414142656.63749-3-badhri@google.comSigned-off-by:
-
Jeremy Linton authored
The dwc2 driver has everything we need to run in ACPI mode except for the ACPI module device table boilerplate. With that added and identified as "BCM2848", an id in use by other OSs for this device, the dw2 controller on the BCM2711 will work. Signed-off-by:
Jeremy Linton <jeremy.linton@arm.com> Link: https://lore.kernel.org/r/20210413215834.3126447-2-jeremy.linton@arm.comSigned-off-by:
-
Thinh Nguyen authored
Add a new DT option to disable LPM for gadget and update the description for usb2-lpm-disable related to host for clarity. Acked-by:
-
Oliver Neukum authored
suspend() does its poisoning conditionally, resume() does it unconditionally. On a device with combined interfaces this will balance, on a device with two interfaces the counter will go negative and resubmission will fail. Both actions need to be done conditionally. Fixes: 6069e3e9 ("USB: cdc-acm: untangle a circular dependency between callback and softint") Signed-off-by:
Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210421074513.4327-1-oneukum@suse.comSigned-off-by:
-
Chris Chiu authored
Realtek Hub (0bda:5487) in Dell Dock WD19 sometimes fails to work after the system resumes from suspend with remote wakeup enabled device connected: [ 1947.640907] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71) [ 1947.641208] usb 5-2.3-port5: cannot disable (err = -71) [ 1947.641401] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71) [ 1947.641450] usb 5-2.3-port4: cannot reset (err = -71) Information of this hub: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 5 D: Ver= 2.10 Cls=09(hub ) Sub=00 Prot=02 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=5487 Rev= 1.47 S: Manufacturer=Dell Inc. S: Product=Dell dock C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=01 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms I:* If#= 0 Alt= 1 #EPs= 1 Cls=09(hub ) Sub=00 Prot=02 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms The failure results from the ETIMEDOUT by chance when turning on the suspend feature for the specified port of the hub. The port seems to be in an unknown state so the hub_activate during resume fails the hub_port_status, then the hub will fail to work. The quirky hub needs the reset-resume quirk to function correctly. Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Chris Chiu <chris.chiu@canonical.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210420174651.6202-1-chris.chiu@canonical.comSigned-off-by:
-
Colin Ian King authored
The variable status is being initialized with a value that is never read and it is being updated later with a new value. The initialization is redundant and can be removed and move the declaration of status to the scope where it is used. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Addresses-Coverity: ("Unused value") Link: https://lore.kernel.org/r/20210420110622.377339-1-colin.king@canonical.comSigned-off-by:
-
Colin Ian King authored
The variable result is being assigned with a value that is never read, the assignment is redundant and can be removed. Acked-by:
-
Malte Deiseroth authored
Correct missing space error ceckpatch.pl is complaining about. Signed-off-by:
Malte Deiseroth <mdeiseroth88@gmail.com> Link: https://lore.kernel.org/r/20210416080843.GA137657@utopSigned-off-by:
-
Saurav Girepunje authored
Fix Error reported by checkpatch.pl ERROR: space required after that ',' (ctx:VxV) +#define can_bulk_split(musb,type) \ ^ ERROR: space required after that ',' (ctx:VxV) +#define can_bulk_combine(musb,type) \ ^ Signed-off-by:Saurav Girepunje <saurav.girepunje@google.com> Link: https://lore.kernel.org/r/20210418174720.GA59520@userSigned-off-by:
-
Anirudh Rayabharam authored
Fix a general protection fault reported by syzbot due to a race between gadget_setup() and gadget_unbind() in raw_gadget. The gadget core is supposed to guarantee that there won't be any more callbacks to the gadget driver once the driver's unbind routine is called. That guarantee is enforced in usb_gadget_remove_driver as follows: usb_gadget_disconnect(udc->gadget); if (udc->gadget->irq) synchronize_irq(udc->gadget->irq); udc->driver->unbind(udc->gadget); usb_gadget_udc_stop(udc); usb_gadget_disconnect turns off the pullup resistor, telling the host that the gadget is no longer connected and preventing the transmission of any more USB packets. Any packets that have already been received are sure to processed by the UDC driver's interrupt handler by the time synchronize_irq returns. But this doesn't work with dummy_hcd, because dummy_hcd doesn't use interrupts; it uses a timer instead. It does have code to emulate the effect of synchronize_irq, but that code doesn't get invoked at the right time -- it currently runs in usb_gadget_udc_stop, after the unbind callback instead of before. Indeed, there's no way for usb_gadget_remove_driver to invoke this code before the unbind callback. To fix this, move the synchronize_irq() emulation code to dummy_pullup so that it runs before unbind. Also, add a comment explaining why it is necessary to have it there. Reported-by: syzbot+eb4674092e6cc8d9e0bd@syzkaller.appspotmail.com Suggested-by:Anirudh Rayabharam <mail@anirudhrb.com> Link: https://lore.kernel.org/r/20210419033713.3021-1-mail@anirudhrb.com Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Thinh Nguyen authored
The START_TRANSFER command needs to be executed while in ON/U0 link state (with an exception during register initialization). Don't use dwc->link_state to check this since the driver only tracks the link state when the link state change interrupt is enabled. Check the link state from DSTS register instead. Note that often the host already brings the device out of low power before it sends/requests the next transfer. So, the user won't see any issue when the device starts transfer then. This issue is more noticeable in cases when the device delays starting transfer, which can happen during delayed control status after the host put the device in low power. Fixes: 799e9dc8 ("usb: dwc3: gadget: conditionally disable Link State change events") Cc: <stable@vger.kernel.org> Acked-by:
-
Hemant Kumar authored
Upon driver unbind usb_free_all_descriptors() function frees all speed descriptor pointers without setting them to NULL. In case gadget speed changes (i.e from super speed plus to super speed) after driver unbind only upto super speed descriptor pointers get populated. Super speed plus desc still holds the stale (already freed) pointer. Fix this issue by setting all descriptor pointers to NULL after freeing them in usb_free_all_descriptors(). Fixes: f5c61225 ("usb: gadget: Update function for SuperSpeedPlus") cc: stable@vger.kernel.org Reviewed-by:
Peter Chen <peter.chen@kernel.org> Signed-off-by:
Hemant Kumar <hemantk@codeaurora.org> Signed-off-by:
Wesley Cheng <wcheng@codeaurora.org> Link: https://lore.kernel.org/r/1619034452-17334-1-git-send-email-wcheng@codeaurora.orgSigned-off-by:
-
Badhri Jagan Sridharan authored
"usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply" introduced a regression for req_out_volt and req_op_curr calculation. req_out_volt should consider the newly calculated max voltage instead of previously accepted max voltage by the port partner. Likewise, req_op_curr should consider the newly calculated max current instead of previously accepted max current by the port partner. Fixes: e3a07202 ("usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply") Reviewed-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
- 14 Apr, 2021 12 commits
-
-
Chunfeng Yun authored
Now some members about phys and wakeup are not used anymore, remove them. Signed-off-by:
-
Chunfeng Yun authored
Use clock bulk helpers to get/enable/disable clocks, meanwhile make sys_ck optional, then will be easier to handle clocks. Signed-off-by:
-
Chunfeng Yun authored
A dedicated wakeup irq will be used to handle runtime suspend/resume, we use dev_pm_set_dedicated_wake_irq API to take care of requesting and attaching wakeup irq, then the suspend/resume framework will help to enable/disable wakeup irq. The runtime PM is default off since some platforms may not support it. users can enable it via power/control (set "auto") in sysfs. Signed-off-by:
-
Chunfeng Yun authored
Add an interrupt which is EINT usually to support runtime PM, meanwhile add "interrupt-names" property, for backward compatibility, it's optional and used when wakeup interrupt exists Reviewed-by:
-
Chunfeng Yun authored
Return error number if encounter errors during suspend and resume. Signed-off-by:
-
Badhri Jagan Sridharan authored
When a PD charger advertising Rp-3.0 is connected to a sink port, the sink port current limit would 3A, during SNK_DISCOVERY, till power negotiation starts. Once the negotiation starts the power limit needs to drop down to pSnkStby(500mA @ 5V) and to negotiated current limit once the explicit contract is in place. Not all charging loops can ramp up to 3A and drop down to 500mA within tSnkStdby which is 15ms. The port partner might hard reset if tSnkStdby is not met. To solve this problem, this patch introduces slow-charger-loop which when set makes the port request PD_P_SNK_STDBY_MW upon entering SNK_DISCOVERY(instead of 3A or the 1.5A during SNK_DISCOVERY) and the actual currrent limit after RX of PD_CTRL_PSRDY for PD link or during SNK_READY for non-pd link. Reviewed-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by:
-
Badhri Jagan Sridharan authored
>From PD Spec: The Sink Shall transition to Sink Standby before a positive or negative voltage transition of VBUS. During Sink Standby the Sink Shall reduce its power draw to pSnkStdby. This allows the Source to manage the voltage transition as well as supply sufficient operating current to the Sink to maintain PD operation during the transition. The Sink Shall complete this transition to Sink Standby within tSnkStdby after evaluating the Accept Message from the Source. The transition when returning to Sink operation from Sink Standby Shall be completed within tSnkNewPower. The pSnkStdby requirement Shall only apply if the Sink power draw is higher than this level. The above requirement needs to be met to prevent hard resets from port partner. Without the patch: (5V/3A during SNK_DISCOVERY all the way through explicit contract) [ 95.711984] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected] [ 95.712007] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS] [ 95.712017] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS] [ 95.837190] VBUS on [ 95.882075] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms] [ 95.882082] state change SNK_DEBOUNCED -> SNK_ATTACHED [rev3 NONE_AMS] [ 95.882086] polarity 1 [ 95.883151] set_auto_vbus_discharge_threshold mode:0 pps_active:n vbus:5000 ret:0 [ 95.883441] enable vbus discharge ret:0 [ 95.883445] Requesting mux state 1, usb-role 2, orientation 2 [ 95.883776] state change SNK_ATTACHED -> SNK_STARTUP [rev3 NONE_AMS] [ 95.883879] pending state change SNK_STARTUP -> SNK_DISCOVERY @ 500 ms [rev3 NONE_AMS] [ 96.038960] VBUS on [ 96.383939] state change SNK_STARTUP -> SNK_DISCOVERY [delayed 500 ms] [ 96.383946] Setting voltage/current limit 5000 mV 3000 mA [ 96.383961] vbus=0 charge:=1 [ 96.386044] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES [rev3 NONE_AMS] [ 96.386309] pending state change SNK_WAIT_CAPABILITIES -> HARD_RESET_SEND @ 450 ms [rev3 NONE_AMS] [ 96.394404] PD RX, header: 0x2161 [1] [ 96.394408] PDO 0: type 0, 5000 mV, 3000 mA [E] [ 96.394410] PDO 1: type 0, 9000 mV, 2000 mA [] [ 96.394412] state change SNK_WAIT_CAPABILITIES -> SNK_NEGOTIATE_CAPABILITIES [rev2 POWER_NEGOTIATION] [ 96.394416] Setting usb_comm capable false [ 96.395083] cc=0 cc1=0 cc2=5 vbus=0 vconn=sink polarity=1 [ 96.395089] Requesting PDO 1: 9000 mV, 2000 mA [ 96.395093] PD TX, header: 0x1042 [ 96.397404] PD TX complete, status: 0 [ 96.397424] pending state change SNK_NEGOTIATE_CAPABILITIES -> HARD_RESET_SEND @ 60 ms [rev2 POWER_NEGOTIATION] [ 96.400826] PD RX, header: 0x363 [1] [ 96.400829] state change SNK_NEGOTIATE_CAPABILITIES -> SNK_TRANSITION_SINK [rev2 POWER_NEGOTIATION] [ 96.400832] pending state change SNK_TRANSITION_SINK -> HARD_RESET_SEND @ 500 ms [rev2 POWER_NEGOTIATION] [ 96.577315] PD RX, header: 0x566 [1] [ 96.577321] Setting voltage/current limit 9000 mV 2000 mA [ 96.578363] set_auto_vbus_discharge_threshold mode:3 pps_active:n vbus:9000 ret:0 [ 96.578370] state change SNK_TRANSITION_SINK -> SNK_READY [rev2 POWER_NEGOTIATION] With the patch: [ 168.398573] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected] [ 168.398605] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS] [ 168.398619] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS] [ 168.522348] VBUS on [ 168.568676] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms] [ 168.568684] state change SNK_DEBOUNCED -> SNK_ATTACHED [rev3 NONE_AMS] [ 168.568688] polarity 1 [ 168.569867] set_auto_vbus_discharge_threshold mode:0 pps_active:n vbus:5000 ret:0 [ 168.570158] enable vbus discharge ret:0 [ 168.570161] Requesting mux state 1, usb-role 2, orientation 2 [ 168.570504] state change SNK_ATTACHED -> SNK_STARTUP [rev3 NONE_AMS] [ 168.570634] pending state change SNK_STARTUP -> SNK_DISCOVERY @ 500 ms [rev3 NONE_AMS] [ 169.070689] state change SNK_STARTUP -> SNK_DISCOVERY [delayed 500 ms] [ 169.070695] Setting voltage/current limit 5000 mV 3000 mA [ 169.070702] vbus=0 charge:=1 [ 169.072719] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES [rev3 NONE_AMS] [ 169.073145] pending state change SNK_WAIT_CAPABILITIES -> HARD_RESET_SEND @ 450 ms [rev3 NONE_AMS] [ 169.077162] PD RX, header: 0x2161 [1] [ 169.077172] PDO 0: type 0, 5000 mV, 3000 mA [E] [ 169.077178] PDO 1: type 0, 9000 mV, 2000 mA [] [ 169.077183] state change SNK_WAIT_CAPABILITIES -> SNK_NEGOTIATE_CAPABILITIES [rev2 POWER_NEGOTIATION] [ 169.077191] Setting usb_comm capable false [ 169.077753] cc=0 cc1=0 cc2=5 vbus=0 vconn=sink polarity=1 [ 169.077759] Requesting PDO 1: 9000 mV, 2000 mA [ 169.077762] PD TX, header: 0x1042 [ 169.079990] PD TX complete, status: 0 [ 169.080013] pending state change SNK_NEGOTIATE_CAPABILITIES -> HARD_RESET_SEND @ 60 ms [rev2 POWER_NEGOTIATION] [ 169.083183] VBUS on [ 169.084195] PD RX, header: 0x363 [1] [ 169.084200] state change SNK_NEGOTIATE_CAPABILITIES -> SNK_TRANSITION_SINK [rev2 POWER_NEGOTIATION] [ 169.084206] Setting standby current 5000 mV @ 500 mA [ 169.084209] Setting voltage/current limit 5000 mV 500 mA [ 169.084220] pending state change SNK_TRANSITION_SINK -> HARD_RESET_SEND @ 500 ms [rev2 POWER_NEGOTIATION] [ 169.260222] PD RX, header: 0x566 [1] [ 169.260227] Setting voltage/current limit 9000 mV 2000 mA [ 169.261315] set_auto_vbus_discharge_threshold mode:3 pps_active:n vbus:9000 ret:0 [ 169.261321] state change SNK_TRANSITION_SINK -> SNK_READY [rev2 POWER_NEGOTIATION] [ 169.261570] AMS POWER_NEGOTIATION finished Fixes: f0690a25 ("staging: typec: USB Type-C Port Manager (tcpm)") Reviewed-by:
-
Thinh Nguyen authored
If the device doesn't support LPM, make sure to disable the LPM capability and don't advertise to the host that it supports it. Acked-by:
-
Sandeep Maheswaram authored
This patch adds a shutdown callback to USB DWC core driver to ensure that it is properly shutdown in reboot/shutdown path. This is required where SMMU address translation is enabled like on SC7180 SoC and few others. If the hardware is still accessing memory after SMMU translation is disabled as part of SMMU shutdown callback in system reboot or shutdown path, then IOVAs(I/O virtual address) which it was using will go on the bus as the physical addresses which might result in unknown crashes (NoC/interconnect errors). Acked-by:
Sandeep Maheswaram <sanm@codeaurora.org> Link: https://lore.kernel.org/r/1618380209-20114-1-git-send-email-sanm@codeaurora.orgSigned-off-by:
-
Thinh Nguyen authored
Currently the controller handles single stream only. So, Ignore Packet Pending bit for stream selection and don't search for another stream if the host sends Data Packet with PP=0 (for OUT direction) or ACK with NumP=0 and PP=0 (for IN direction). This slightly improves the stream performance. Acked-by:
-
Kai-Heng Feng authored
This is another branded 8153 device that doesn't work well with LPM enabled: [ 400.597506] r8152 5-1.1:1.0 enx482ae3a2a6f0: Tx status -71 So disable LPM to resolve the issue. Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> BugLink: https://bugs.launchpad.net/bugs/1922651 Link: https://lore.kernel.org/r/20210412135455.791971-1-kai.heng.feng@canonical.com Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Dan Carpenter authored
Smatch complains about a potential missing error code: drivers/usb/typec/port-mapper.c:168 typec_link_port() warn: missing error code 'ret' This is a false positive and returning zero is intentional. Let's re-arrange the code to silence the warning and make the intent more clear. Reviewed-by:Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/YHadaACH8Mq/10F7@mwandaSigned-off-by:
-
- 13 Apr, 2021 2 commits
-
-
Mauro Carvalho Chehab authored
Now that the xr_serial got support for other models, add their USB IDs as well. The Maxlinear/Exar USB UARTs can be used in either ACM mode using the cdc-acm driver or in "custom driver" mode in which further features such as hardware and software flow control, GPIO control and in-band line-status reporting are available. In ACM mode the device always enables RTS/CTS flow control, something which could prevent transmission in case the CTS input isn't wired up correctly. Ensure that cdc_acm will not bind to these devices if the custom USB-serial driver is enabled. Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Link: https://lore.kernel.org/r/5155887a764cbc11f8da0217fe08a24a77d120b4.1616571453.git.mchehab+huawei@kernel.org [ johan: rewrite commit message, clean up entries ] Cc: Oliver Neukum <oneukum@suse.com> Reviewed-by:
Johan Hovold <johan@kernel.org>
-
Johan Hovold authored
Add another copyright notice for the work done in 2021. Signed-off-by:
-
