The Kconfig entry for USB_OMAP unconditionally selects USB_ISP1301,
which is now only visible when USB_PHY is also enabled.

This adds an appropriate dependency and enables USB_PHY in the omap1
defconfig, avoiding these build warnings:

warning: (USB_OHCI_HCD && USB_OMAP) selects ISP1301_OMAP which has unmet direct dependencies (USB_SUPPORT && USB_PHY && I2C && ARCH_OMAP_OTG)

Also fix a Makefile typo while we're at it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Kconfig entry for USB_LPC32XX unconditionally selects USB_ISP1301,
which is now only visible when USB_PHY is also enabled.

This adds an appropriate dependency and enables USB_PHY in the msm
defconfig, avoiding these build errors:

warning: (USB_LPC32XX) selects USB_ISP1301 which has unmet direct dependencies (USB_SUPPORT && USB_PHY && (USB || USB_GADGET) && I2C)
drivers/built-in.o: In function `usb_hcd_nxp_probe':
drivers/usb/host/ohci-nxp.c:224: undefined reference to `isp1301_get_client'
drivers/built-in.o: In function `lpc32xx_udc_probe':
drivers/usb/gadget/lpc32xx_udc.c:3071: undefined reference to `isp1301_get_client'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The FT4232H used in the ST Micro Connect Lite has four hi-speed UART ports.
The first two ports are reserved for the JTAG interface.

We enable by default ports 2 and 3 as UARTs (where port 2 is a
conventional RS-232 UART)
Signed-off-by: Adrian Thomasset <adrian.thomasset@st.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Both phy-tegra-usb.c and ehci-tegra.c export symbols used by the other one,
which does not work if one of them or both are loadable modules, resulting
in an error like:

drivers/built-in.o: In function `utmi_phy_clk_disable':
drivers/usb/phy/phy-tegra-usb.c:302: undefined reference to `tegra_ehci_set_phcd'
drivers/built-in.o: In function `utmi_phy_clk_enable':
drivers/usb/phy/phy-tegra-usb.c:324: undefined reference to `tegra_ehci_set_phcd'
drivers/built-in.o: In function `utmi_phy_power_on':
drivers/usb/phy/phy-tegra-usb.c:447: undefined reference to `tegra_ehci_set_pts'

This turns the interface into a one-way dependency by letting the tegra ehci
driver pass two function pointers for callbacks that need to be called by
the phy driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A lot of platform code calls into the usb phy core at the moment, which
does not work if it is built as a loadable module. This will hopefully
change when those platforms are all converted to DT based probing,
but for now, the easiest solution is to change it from "tristate"
to "bool".

This solves at least these ARM allmodconfig build errors:

arch/arm/mach-imx/built-in.o: In function `imx_otg_ulpi_create':
arch/arm/mach-imx/ulpi.c:117: undefined reference to `otg_ulpi_create'
arch/arm/mach-omap2/built-in.o: In function `usbhs_init_phys':
arch/arm/mach-omap2/usb-host.c:652: undefined reference to `usb_bind_phy'
arch/arm/mach-omap2/built-in.o: In function `omap_2430sdp_init':
arch/arm/mach-omap2/board-2430sdp.c:236: undefined reference to `usb_bind_phy'
arch/arm/mach-omap2/built-in.o: In function `omap3_beagle_init':
arch/arm/mach-omap2/board-omap3beagle.c:554: undefined reference to `usb_bind_phy'
arch/arm/mach-omap2/built-in.o: In function `devkit8000_init':
arch/arm/mach-omap2/board-devkit8000.c:596: undefined reference to `usb_bind_phy'
arch/arm/mach-omap2/built-in.o: In function `omap_ldp_init':
arch/arm/mach-omap2/board-ldp.c:379: undefined reference to `usb_bind_phy'
drivers/built-in.o: In function `ab8500_charger_probe':
drivers/power/ab8500_charger.c:3629: undefined reference to `usb_get_phy'
drivers/power/ab8500_charger.c:3706: undefined reference to `usb_put_phy'
drivers/built-in.o: In function `ab8500_charger_remove':
drivers/power/ab8500_charger.c:3411: undefined reference to `usb_put_phy'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix some of the initconst markings in the ehci driver(s).
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Many cards based on CY7C68300A/B/C use the USB ID 04b4:6830 but only the
B and C variants (EZ-USB AT2LP) support the ATA Command Block
functionality, according to the data sheets. The A variant (EZ-USB AT2)
locks up if ATACB is attempted, until a typical 30 seconds timeout runs
out and a USB reset is performed.

https://bugs.launchpad.net/bugs/428469

It seems that one way to spot a CY7C68300A (at least where the card
manufacturer left Cypress' EEPROM default vaules, against Cypress'
recommendations) is to look at the USB string descriptor indices.

A http://media.digikey.com/pdf/Data%20Sheets/Cypress%20PDFs/CY7C68300A.pdf
B http://www.farnell.com/datasheets/43456.pdf
C http://www.cypress.com/?rID=14189

Note that a CY7C68300B/C chip appears as CY7C68300A if it is running
in Backward Compatibility Mode, and if ATACB would be supported in this
case there is anyway no way to tell which chip it really is.

For 5 years my external USB drive has been locking up for half a minute
when plugged in and ata_id is run by udev, or anytime hdparm or similar
is run on it.

Finally looking at the /correct/ datasheet I think I found the reason. I
am aware the quirk in this patch is a bit hacky, but the hardware
manufacturers haven't made it easy for us.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds PID for Olivetti Olicard 145 in option.c
Signed-off-by: Filippo Turato <nnj7585@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The current ST Micro Connect Lite uses the FT4232H hi-speed quad USB
UART FTDI chip. It is also possible to drive STM reference targets
populated with an on-board JTAG debugger based on the FT2232H chip with
the same STMicroelectronics tools.

For this reason, the ST Micro Connect Lite PIDs should be
ST_STMCLT_2232_PID: 0x3746
ST_STMCLT_4232_PID: 0x3747
Signed-off-by: Adrian Thomasset <adrian.thomasset@st.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'usb-for-v3.10-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

Felipe writes:

usb: urgent fixes for v3.10 merge window

Here are some late urgent fixes for v3.10 merge window.

All of these errors were introduced by recent commits
which are in linux-next.

f_obex, multi and cdc2 gadget drivers have learned to
return a proper error code when something goes wrong.

usb_bind_phy() was mistakenly placed into .init.text
section which caused Section mismatch warnings and undefined
reference compile errors.

f_source_sink had a copy-paste error which is now corrected.

g_zero got a memory leak plugged.

Two defconfigs got fixed to enable the newly introduced
CONFIG_USB_PHY.

Commit edc7cb2e (usb: phy: make it a menuconfig) makes USB_MXS_PHY
be a sub-item of menuconfig symbol USB_PHY.  This change gets the
selection of CONFIG_USB_MXS_PHY in mxs_defconfig lost.  Hence the
boot stops at the point below.

  [    1.600867] ci_hdrc ci_hdrc.0: doesn't support gadget
  [    1.606282] ci_hdrc ci_hdrc.0: EHCI Host Controller
  [    1.613522] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1

Add CONFIG_USB_PHY to have the CONFIG_USB_MXS_PHY selection back to
work.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Commit edc7cb2e (usb: phy: make it a menuconfig) makes USB_MXS_PHY
be a sub-item of menuconfig symbol USB_PHY.  This change gets the
selection of CONFIG_USB_MXS_PHY in imx_v6_v7_defconfig lost.  Hence the
boot stops at the point below.

  ci_hdrc ci_hdrc.0: doesn't support gadget
  ci_hdrc ci_hdrc.0: EHCI Host Controller
  ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1

Add CONFIG_USB_PHY to have the CONFIG_USB_MXS_PHY selection back to
work.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The symbol usb_bind_phy is exported and annotated __init.
It looks like section mismatch. Fix by removing the
__init annotation of usb_bind_phy.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

If function instances are not put on gadget's unbind, their implementation
module's refcount is nonzero and it is impossible to unload them.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

acm was the first function to be converted and it seems that its
code served as a base for converting f_sourcesink to the new function
interface. source_sink has nothing to do with acm, though.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.

Introduced by commit 29a664 (usb: gadget: cdc2: use function
framework for ACM)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.

Introduced by commit 59835a (usb: gadget: multi: use
function framework for ACM.)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Now that Joe cleaned up the init/exit functions, we can just get rid of
them entirely and use the proper macro that almost all other USB drivers
now use.

Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use a more current logging style with dev_printk
where possible.

o Convert uses of US_DEBUGP to usb_stor_dbg
o Add "struct us_data *" to usb_stor_dbg uses
o usb_stor_dbg now uses struct device */dev_vprint_emit
o Removed embedded function names
o Coalesce formats
o Remove trailing whitespace
o Remove useless OOM messages
o Remove useless function entry/exit logging
o Convert some US_DEBUGP uses to dev_info and dev_dbg

Object size is slightly reduced when debugging
is enabled, slightly increased with no debugging
because some initialization and removal messages
are now always emitted.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Kill custom closing_wait implementation and let the tty-layer handle it
instead.

Note that the port drain-delay is set to three characters to keep the
20ms delay after wait_until_sent at low baudrates (1200 baud) during close.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove redundant drain, which has already been handled by the tty-layer,
from break_ctl.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Query hardware-buffer status in chars_in_buffer should the write fifo be
empty.

This is needed to make the tty layer wait for hardware buffers to drain
on close.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The line status register is only polled so let's not keep a possibly
outdated value in the port data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Move write-fifo flushing from ti_drain to close where it belongs.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove redundant wait_until_sent, which has already been handled by the
tty-layer, from break_ctl.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix regression introduced by commit f40d7815 ("USB: io_ti: kill custom
closing_wait implementation") which made TIOCGSERIAL return the wrong
value for closing_wait.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org> # 3.9
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Inside usbtmc_ioctl_clear_out_halt()/usbtmc_ioctl_clear_in_halt(),
usb_clear_halt() needn't any buffer to pass in, so remove the
unnecessary memory allocation.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The dereference to 'instance' in the debug code should be moved
below the NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix allmodconfig link error introduced by commit 75b9130e
("usb: storage: Add usb_stor_dbg, reduce object size")

Export the symbol usb_stor_dbg.
Add export.h
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Allocate port-private data in port-probe rather than in attach.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use port device for debug messages in interrupt-urb callback and remove
unused private data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the port interrupt-in urb rather managing a private one.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The device uses the second interrupt-in endpoint of the interface for
reading. Stop abusing the port read urb and store a pointer to the
second interrupt-in urb as port-private data instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the port interrupt-out urb rather than abusing the port write_urb
pointer and allocating a new urb at every open (but the first...).

Note that the write_urb abuse would have led to a double free should
there ever be interfaces with a bulk-out endpoint.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove unused interrupt-in endpoint address from private data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace broken and commented-out debug code with usb_serial_debug_data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Switch to the more efficient generic read implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactor read-urb processing, and add sanity checks on header and data
lengths.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove redundant data-offset define, which was really just the header
length.

Add payload-size define and use the bulk-out size define for the actual
bulk-out size.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>