gcc warns that the temporary buffer might be too small here:

drivers/net/ethernet/cavium/thunder/thunder_bgx.c: In function 'bgx_probe':
drivers/net/ethernet/cavium/thunder/thunder_bgx.c:1020:16: error: '%d' directive writing between 1 and 10 bytes into a region of size between 9 and 11 [-Werror=format-overflow=]
sprintf(str, "BGX%d LMAC%d mode", bgx->bgx_id, lmacid);
             ^~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/cavium/thunder/thunder_bgx.c:1020:16: note: directive argument in the range [0, 2147483647]
drivers/net/ethernet/cavium/thunder/thunder_bgx.c:1020:3: note: 'sprintf' output between 16 and 27 bytes into a destination of size 20

This probably can't happen, but it can't hurt to make it long
enough for the theoretical limit.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

gcc notices that large queue numbers would overflow the queue name
string:

drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c: In function 'bnx2x_get_strings':
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c:3165:25: error: '%d' directive writing between 1 and 10 bytes into a region of size 5 [-Werror=format-overflow=]
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c:3165:25: note: directive argument in the range [0, 2147483647]
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c:3165:5: note: 'sprintf' output between 2 and 11 bytes into a destination of size 5

There is a hard limit in place that makes the number at most two
digits, so the code is fine. This changes it to use snprintf()
to truncate instead of overflowing, which shuts up that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

We get a warning for the port_name string that might be longer than
six characters if we had more than 10 ports:

drivers/net/ethernet/sun/niu.c: In function 'niu_put_parent':
drivers/net/ethernet/sun/niu.c:9563:21: error: '%d' directive writing between 1 and 3 bytes into a region of size 2 [-Werror=format-overflow=]
  sprintf(port_name, "port%d", port);
                     ^~~~~~~~
drivers/net/ethernet/sun/niu.c:9563:21: note: directive argument in the range [0, 255]
drivers/net/ethernet/sun/niu.c:9563:2: note: 'sprintf' output between 6 and 8 bytes into a destination of size 6
  sprintf(port_name, "port%d", port);
  ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/sun/niu.c: In function 'niu_pci_init_one':
drivers/net/ethernet/sun/niu.c:9538:22: error: '%d' directive writing between 1 and 3 bytes into a region of size 2 [-Werror=format-overflow=]
   sprintf(port_name, "port%d", port);
                      ^~~~~~~~
drivers/net/ethernet/sun/niu.c:9538:22: note: directive argument in the range [0, 255]
drivers/net/ethernet/sun/niu.c:9538:3: note: 'sprintf' output between 6 and 8 bytes into a destination of size 6

While we know that the port number is small, there is no harm in
making the format string two bytes longer to avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

One string we pass into the cs->info buffer might be too long,
as pointed out by gcc:

drivers/isdn/divert/isdn_divert.c: In function 'll_callback':
drivers/isdn/divert/isdn_divert.c:488:22: error: '%d' directive writing between 1 and 3 bytes into a region of size between 1 and 69 [-Werror=format-overflow=]
 sprintf(cs->info, "%d 0x%lx %s %s %s %s 0x%x 0x%x %d %d %s\n",
                   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/isdn/divert/isdn_divert.c:488:22: note: directive argument in the range [0, 255]
drivers/isdn/divert/isdn_divert.c:488:4: note: 'sprintf' output 25 or more bytes (assuming 129) into a destination of size 90

This is unlikely to actually cause problems, so let's use snprintf
as a simple workaround to shut  up the warning and truncate the
buffer instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the interface is not up, then don't try to close it during a
shutdown.  This avoids possible double free of the IRQ, which
can happen during a shutdown.

Fixes: 03eb3eb4 ("net: qcom/emac: add shutdown function")
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change enables the use of SW timestamping on Raspberry PI.

smsc95xx uses the usbnet transmit function usbnet_start_xmit(), which
implements software timestamping. However the SOF_TIMESTAMPING_TX_SOFTWARE
capability was missing and only SOF_TIMESTAMPING_RX_SOFTWARE was announced.
By using ethtool_op_get_ts_info() as get_ts_info() also the
SOF_TIMESTAMPING_TX_SOFTWARE is announced.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make name consistent with other TC event notification routines, such as
tcf_add_notify() and tcf_del_notify()
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When PACKET_QDISC_BYPASS is not used, Tx queue selection will be done
before the packet is enqueued, taking into account any mappings set by
a queuing discipline such as mqprio without hardware offloading. This
selection may be affected by a previously saved queue_mapping, either on
the Rx path, or done before the packet reaches the device, as it's
currently the case for AF_PACKET.

In order for queue selection to work as expected when using traffic
control, there can't be another selection done before that point is
reached, so move the call to packet_pick_tx_queue to
packet_direct_xmit, leaving the default xmit path as it was before
PACKET_QDISC_BYPASS was introduced.

A forward declaration of packet_pick_tx_queue() is introduced to avoid
the need to reorder the functions within the file.

Fixes: d346a3fa ("packet: introduce PACKET_QDISC_BYPASS socket option")
Signed-off-by: Iván Briano <ivan.briano@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With 802.1ad support the vlan_ingress code started checking for vlan
protocol mismatch which causes the current tag to be inserted and the
bridge vlan protocol & pvid to be set. The vlan tag insertion changes
the skb mac_header and thus the lookup mac dest pointer which was loaded
prior to calling br_allowed_ingress in br_handle_frame_finish is VLAN_HLEN
bytes off now, pointing to the last two bytes of the destination mac and
the first four of the source mac causing lookups to always fail and
broadcasting all such packets to all ports. Same thing happens for locally
originated packets when passing via br_dev_xmit. So load the dest pointer
after the vlan checks and possible skb change.

Fixes: 8580e211 ("bridge: Prepare for 802.1ad vlan filtering support")
Reported-by: Anitha Narasimha Murthy <anitha@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check ptp_clock_register() return not only for NULL but
also for error pointers, and also nullify adapter->ptp_clock
if ptp_clock_register() fails.

Fixes: 9c33e420 ("cxgb4: Add PTP Hardware Clock (PHC) support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code only support DT method to control xge led.
This patch is the implementation of acpi method to control xge led.
Signed-off-by: LiuJian <liujian56@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we convert atomic_t to refcount_t, a new kernel warning
on "increment on 0" is introduced in the netpoll code,
zap_completion_queue(). In fact for this special case, we know
the refcount is 0 and we just have to set it to 1 to satisfy
the following dev_kfree_skb_any(), so we can just use
refcount_set(..., 1) instead.

Fixes: 63354797 ("net: convert sk_buff.users from atomic_t to refcount_t")
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Cc: Reshetova, Elena <elena.reshetova@intel.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some firmwares in Huawei E3372H devices have been observed to switch back
to NTB 32-bit format after altsetting switch.
This patch implements a driver flag to check for the device settings and
set NTB format to 16-bit again if needed.
The flag has been activated for devices controlled by the huawei_cdc_ncm.c
driver.

V1->V2:
- fixed broken error checks
- some corrections to the commit message
V2->V3:
- variable name changes, to clarify what's happening
- check (and possibly set) the NTB format later in the common bind code path
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Reported-and-tested-by: Christian Panton <christian@panton.org>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
CC: Bjørn Mork <bjorn@mork.no>
CC: Christian Panton <christian@panton.org>
CC: linux-usb@vger.kernel.org
CC: netdev@vger.kernel.org
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

mdio_mux_init parses the child nodes of the MDIO mux. When using
"mdio-mux-mmioreg" the child nodes are describing the register value
that is written to switch between the MDIO busses.

The change which makes the error messages more verbose changed the
parsing of the "reg" property from a simple of_property_read_u32 call
to of_mdio_parse_addr. On a Khadas VIM (based on the Meson GXL SoC,
which uses mdio-mux-mmioreg) this prevents registering the MDIO mux
(because the "reg" values on the MDIO mux child nodes are 0x2009087f
and 0xe40908ff) and leads to the following errors:
  mdio-mux-mmioreg c883455c.eth-phy-mux: /soc/periphs@c8834000/eth-phy-mux/mdio@e40908ff PHY address -469169921 is too large
  mdio-mux-mmioreg c883455c.eth-phy-mux: Error: Failed to find reg for child /soc/periphs@c8834000/eth-phy-mux/mdio@e40908ff
  mdio-mux-mmioreg c883455c.eth-phy-mux: /soc/periphs@c8834000/eth-phy-mux/mdio@2009087f PHY address 537462911 is too large
  mdio-mux-mmioreg c883455c.eth-phy-mux: Error: Failed to find reg for child /soc/periphs@c8834000/eth-phy-mux/mdio@2009087f
  mdio-mux-mmioreg c883455c.eth-phy-mux: Error: No acceptable child buses found
  mdio-mux-mmioreg c883455c.eth-phy-mux: failed to register mdio-mux bus /soc/periphs@c8834000/eth-phy-mux
(as a result of that ethernet is not working, because the PHY which is
connected through the mux' child MDIO bus, which is not being
registered).

Fix this by reverting the change from of_mdio_parse_addr to
of_mdio_parse_addr.

Fixes: 342fa196 ("mdio: mux: make child bus walking more permissive and errors more verbose")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The configure callback of fib_rules_ops can change the refcnt of a
fib rule. For instance, mlxsw takes a refcnt when adding the processing
of the rule to a work queue. Thus the rule refcnt can not be reset to
to 1 afterwards. Move the refcnt setting to after the allocation.

Fixes: 5361e209 ("net: avoid one splat in fib_nl_delrule()")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Rolf Eike Beer <eb@emlix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add 0x50a3 and 0x50a4 T5 device id's
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't populate array error_code on the stack but make it static. Makes
the object code smaller by almost 250 bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
  10366	    983	      0	  11349	   2c55	net/dccp/input.o

After:
   text	   data	    bss	    dec	    hex	filename
  10161	   1039	      0	  11200	   2bc0	net/dccp/input.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't populate array glrt_table on the stack but make it static.
Makes the object code a smaller by over 670 bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
 131772	   4733	      0	 136505	  21539	rt2800lib.o

After:
   text	   data	    bss	    dec	    hex	filename
 131043	   4789	      0	 135832	  21298	rt2800lib.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't populate array route_possibilities on the stack but make it
static const.  Makes the object code a little smaller by 85 bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
   9901	   2448	      0	  12349	   303d	dwmac4_core.o

After:
   text	   data	    bss	    dec	    hex	filename
   9760	   2504	      0	  12264	   2fe8	dwmac4_core.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't populate various tables on the stack but make them static const.
Makes the object code smaller by nearly 200 bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
 113468	  11200	      0	 124668	  1e6fc	bnx2x_ethtool.o

After:
   text	   data	    bss	    dec	    hex	filename
 113129	  11344	      0	 124473	  1e639	bnx2x_ethtool.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change fixes following problem

[    1.827940] xgene-enet: probe of 1f210030.ethernet failed with error -2

which leads to a missing ethernet interface (reproducable at least on
Gigabyte MP30-AR0 and APM Mustang systems).

The check for a valid clk resource fails, because DT doesn't provide a
clock for sgenet1. But the driver doesn't use this clk, if the ethernet
port is connected via SGMII. Therefore this patch avoids probing for clk
on SGMII interfaces.

Fixes: 9aea7779 ("drivers: net: xgene: Fix crash on DT systems")
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bpf_skb_adjust_net() ignores the return value of bpf_skb_net_shrink/grow,
and always return 0, fix it by return 'ret'.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

1) Fix 64-bit division in mlx5 IPSEC offload support, from Ilan Tayari
   and Arnd Bergmann.

2) Fix race in statistics gathering in bnxt_en driver, from Michael
   Chan.

3) Can't use a mutex in RCU reader protected section on tap driver, from
   Cong WANG.

4) Fix mdb leak in bridging code, from Eduardo Valentin.

5) Fix free of wrong pointer variable in nfp driver, from Dan Carpenter.

6) Buffer overflow in brcmfmac driver, from Arend van SPriel.

7) ioremap_nocache() return value needs to be checked in smsc911x
   driver, from Alexey Khoroshilov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (34 commits)
  net: stmmac: revert "support future possible different internal phy mode"
  sfc: don't read beyond unicast address list
  datagram: fix kernel-doc comments
  socket: add documentation for missing elements
  smsc911x: Add check for ioremap_nocache() return code
  brcmfmac: fix possible buffer overflow in brcmf_cfg80211_mgmt_tx()
  net: hns: Bugfix for Tx timeout handling in hns driver
  net: ipmr: ipmr_get_table() returns NULL
  nfp: freeing the wrong variable
  mlxsw: spectrum_switchdev: Check status of memory allocation
  mlxsw: spectrum_switchdev: Remove unused variable
  mlxsw: spectrum_router: Fix use-after-free in route replace
  mlxsw: spectrum_router: Add missing rollback
  samples/bpf: fix a build issue
  bridge: mdb: fix leak on complete_info ptr on fail path
  tap: convert a mutex to a spinlock
  cxgb4: fix BUG() on interrupt deallocating path of ULD
  qed: Fix printk option passed when printing ipv6 addresses
  net: Fix minor code bug in timestamping.txt
  net: stmmac: Make 'alloc_dma_[rt]x_desc_resources()' look even closer
  ...

I made the mistake of upgrading my desktop to the new Fedora 26 that
comes with gcc-7.1.1.

There's nothing wrong per se that I've noticed, but I now have 1500
lines of warnings, mostly from the new format-truncation warning
triggering all over the tree.

We use 'snprintf()' and friends in a lot of places, and often know that
the numbers are fairly small (ie a controller index or similar), but gcc
doesn't know that, and sees an 'int', and thinks that it could be some
huge number.  And then complains when our buffers are not able to fit
the name for the ten millionth controller.

These warnings aren't necessarily bad per se, and we probably want to
look through them subsystem by subsystem, but at least during the merge
window they just mean that I can't even see if somebody is introducing
any *real* problems when I pull.

So warnings disabled for now.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull modules updates from Jessica Yu:
 "Summary of modules changes for the 4.13 merge window:

   - Minor code cleanups

   - Avoid accessing mod struct prior to checking module struct version,
     from Kees

   - Fix racy atomic inc/dec logic of kmod_concurrent_max in kmod, from
     Luis"

* tag 'modules-for-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
  module: make the modinfo name const
  kmod: reduce atomic operations on kmod_concurrent and simplify
  module: use list_for_each_entry_rcu() on find_module_all()
  kernel/module.c: suppress warning about unused nowarn variable
  module: Add module name to modinfo
  module: Pass struct load_info into symbol checks

Since internal phy-mode is reserved for non-xMII protocol we cannot use
it with dwmac-sun8i.
Furthermore, all DT patchs which comes with this patch were cleaned, so
the current state is broken.
This reverts commit 1c2fa5f8 ("net: stmmac: support future possible different internal phy mode")

Fixes: 1c2fa5f8 ("net: stmmac: support future possible different internal phy mode")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we have more than 32 unicast MAC addresses assigned to an interface
we will read beyond the end of the address table in the driver when
adding filters. The next 256 entries store multicast addresses, so we
will end up attempting to insert duplicate filters, which is mostly
harmless. If we add more than 288 unicast addresses we will then read
past the multicast address table, which is likely to be more exciting.

Fixes: 12fb0da4 ("sfc: clean fallbacks between promisc/normal in efx_ef10_filter_sync_rx_mode")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stephen Hemminger says:

====================
minor net kernel-doc fixes

Fix a couple of small errors in kernel-doc for networking
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

An underscore in the kernel-doc comment section has special meaning
and mis-use generates an errors.

./net/core/datagram.c:207: ERROR: Unknown target name: "msg".
./net/core/datagram.c:379: ERROR: Unknown target name: "msg".
./net/core/datagram.c:816: ERROR: Unknown target name: "t".
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fill in missing kernel-doc for missing elements in struct sock.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no check for return code of smsc911x_drv_probe()
in smsc911x_drv_probe(). The patch adds one.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull i2c updates from Wolfram Sang:
 "This pull request contains:

   - i2c core reorganization. One source file became too monolithic. It
     is now split up, yet we still have the same named object as the
     final output. This should ease maintenance.

   - new drivers: ZTE ZX2967 family, ASPEED 24XX/25XX

   - designware driver gained slave mode support

   - xgene-slimpro driver gained ACPI support

   - bigger overhaul for pca-platform driver

   - the algo-bit module now supports messages with enforced STOP

   - slightly bigger than usual set of driver updates and improvements

  and with much appreciated quality assurance from Andy Shevchenko"

* 'i2c/for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (51 commits)
  i2c: Provide a stub for i2c_detect_slave_mode()
  i2c: designware: Let slave adapter support be optional
  i2c: designware: Make HW init functions static
  i2c: designware: fix spelling mistakes
  i2c: pca-platform: propagate error from i2c_pca_add_numbered_bus
  i2c: pca-platform: correctly set algo_data.reset_chip
  i2c: acpi: Do not create i2c-clients for LNXVIDEO ACPI devices
  i2c: designware: enable SLAVE in platform module
  i2c: designware: add SLAVE mode functions
  i2c: zx2967: drop COMPILE_TEST dependency
  i2c: zx2967: always use the same device when printing errors
  i2c: pca-platform: use dev_warn/dev_info instead of printk
  i2c: pca-platform: use device managed allocations
  i2c: pca-platform: add devicetree awareness
  i2c: pca-platform: switch to struct gpio_desc
  dt-bindings: add bindings for i2c-pca-platform
  i2c: cadance: fix ctrl/addr reg write order
  i2c: zx2967: add i2c controller driver for ZTE's zx2967 family
  dt: bindings: add documentation for zx2967 family i2c controller
  i2c: algo-bit: add support for I2C_M_STOP
  ...

Pull IOMMU updates from Joerg Roedel:
 "This update comes with:

   - Support for lockless operation in the ARM io-pgtable code.

     This is an important step to solve the scalability problems in the
     common dma-iommu code for ARM

   - Some Errata workarounds for ARM SMMU implemenations

   - Rewrite of the deferred IO/TLB flush code in the AMD IOMMU driver.

     The code suffered from very high flush rates, with the new
     implementation the flush rate is down to ~1% of what it was before

   - Support for amd_iommu=off when booting with kexec.

     The problem here was that the IOMMU driver bailed out early without
     disabling the iommu hardware, if it was enabled in the old kernel

   - The Rockchip IOMMU driver is now available on ARM64

   - Align the return value of the iommu_ops->device_group call-backs to
     not miss error values

   - Preempt-disable optimizations in the Intel VT-d and common IOVA
     code to help Linux-RT

   - Various other small cleanups and fixes"

* tag 'iommu-updates-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (60 commits)
  iommu/vt-d: Constify intel_dma_ops
  iommu: Warn once when device_group callback returns NULL
  iommu/omap: Return ERR_PTR in device_group call-back
  iommu: Return ERR_PTR() values from device_group call-backs
  iommu/s390: Use iommu_group_get_for_dev() in s390_iommu_add_device()
  iommu/vt-d: Don't disable preemption while accessing deferred_flush()
  iommu/iova: Don't disable preempt around this_cpu_ptr()
  iommu/arm-smmu-v3: Add workaround for Cavium ThunderX2 erratum #126
  iommu/arm-smmu-v3: Enable ACPI based HiSilicon CMD_PREFETCH quirk(erratum 161010701)
  iommu/arm-smmu-v3: Add workaround for Cavium ThunderX2 erratum #74
  ACPI/IORT: Fixup SMMUv3 resource size for Cavium ThunderX2 SMMUv3 model
  iommu/arm-smmu-v3, acpi: Add temporary Cavium SMMU-V3 IORT model number definitions
  iommu/io-pgtable-arm: Use dma_wmb() instead of wmb() when publishing table
  iommu/io-pgtable: depend on !GENERIC_ATOMIC64 when using COMPILE_TEST with LPAE
  iommu/arm-smmu-v3: Remove io-pgtable spinlock
  iommu/arm-smmu: Remove io-pgtable spinlock
  iommu/io-pgtable-arm-v7s: Support lockless operation
  iommu/io-pgtable-arm: Support lockless operation
  iommu/io-pgtable: Introduce explicit coherency
  iommu/io-pgtable-arm-v7s: Refactor split_blk_unmap
  ...

Pull overlayfs updates from Miklos Szeredi:
 "This work from Amir introduces the inodes index feature, which
  provides:

   - hardlinks are not broken on copy up

   - infrastructure for overlayfs NFS export

  This also fixes constant st_ino for samefs case for lower hardlinks"

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs: (33 commits)
  ovl: mark parent impure and restore timestamp on ovl_link_up()
  ovl: document copying layers restrictions with inodes index
  ovl: cleanup orphan index entries
  ovl: persistent overlay inode nlink for indexed inodes
  ovl: implement index dir copy up
  ovl: move copy up lock out
  ovl: rearrange copy up
  ovl: add flag for upper in ovl_entry
  ovl: use struct copy_up_ctx as function argument
  ovl: base tmpfile in workdir too
  ovl: factor out ovl_copy_up_inode() helper
  ovl: extract helper to get temp file in copy up
  ovl: defer upper dir lock to tempfile link
  ovl: hash overlay non-dir inodes by copy up origin
  ovl: cleanup bad and stale index entries on mount
  ovl: lookup index entry for copy up origin
  ovl: verify index dir matches upper dir
  ovl: verify upper root dir matches lower root dir
  ovl: introduce the inodes index dir feature
  ovl: generalize ovl_create_workdir()
  ...

Reported-and-tested-by: Meelis Roos <mroos@linux.ee>
Fixes: commit d9e968cb "getrlimit()/setrlimit(): move compat to native"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The lower level nl80211 code in cfg80211 ensures that "len" is between
25 and NL80211_ATTR_FRAME (2304).  We subtract DOT11_MGMT_HDR_LEN (24) from
"len" so thats's max of 2280.  However, the action_frame->data[] buffer is
only BRCMF_FIL_ACTION_FRAME_SIZE (1800) bytes long so this memcpy() can
overflow.

	memcpy(action_frame->data, &buf[DOT11_MGMT_HDR_LEN],
	       le16_to_cpu(action_frame->len));

Cc: stable@vger.kernel.org # 3.9.x
Fixes: 18e2f61d ("brcmfmac: P2P action frame tx.")
Reported-by: "freenerguo(郭大兴)" <freenerguo@tencent.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When hns port type is not debug mode, netif_tx_disable is called
when there is a tx timeout, which requires system reboot to return
to normal state. This patch fix this problem by resetting the net
dev.

Fixes: b5996f11 ("net: add Hisilicon Network Subsystem basic ethernet support")
Signed-off-by: Lin Yun Sheng <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ipmr_get_table() function doesn't return error pointers it returns
NULL on error.

Fixes: 4f75ba69 ("net: ipmr: Add ipmr_rtm_getroute")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We accidentally free a NULL pointer and leak the pointer we want to
free.  Also you can tell from the label name what was intended.  :)

Fixes: abfcdc1d ("nfp: add a stats handler for flower offloads")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>