key_basic is set twice in __skb_flow_dissect which seems unnecessary.
Remove second one.
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add uapi define for MPLS over IP.
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do break when we see routing flag or a non-zero version number in GRE
header.
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to <stdbool.h> false is always '0' and
Static variables are initialised to 0 by GCC.
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fix build error:
net/core/filter.c: In function 'bpf_clone_redirect':
net/core/filter.c:1429:18: error: 'struct sk_buff' has no member named 'tc_verd'
  if (G_TC_AT(skb2->tc_verd) & AT_INGRESS)

Fixes: 3896d655 ("bpf: introduce bpf_clone_redirect() helper")
Reported-by: Or Gerlitz <gerlitz.or@gmail.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xen virtual network driver has higher latency than a physical NIC.
Having only 128K as limit for TSQ introduced 30% regression in guest
throughput.

This patch raises the limit to 256K. This reduces the regression to 8%.
This buys us more time to work out a proper solution in the long run.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_v4_rcv() checks the following before calling tcp_v4_do_rcv():

if (th->doff < sizeof(struct tcphdr) / 4)
    goto bad_packet;
if (!pskb_may_pull(skb, th->doff * 4))
    goto discard_it;

So following check in tcp_v4_do_rcv() is redundant
and "goto csum_err;" is wrong anyway.

if (skb->len < tcp_hdrlen(skb) || ...)
	goto csum_err;

A second check can be removed after no_tcp_socket label for same reason.

Same tests can be removed in tcp_v6_do_rcv()

Note : short tcp frames are not properly accounted in tcpInErrs MIB,
because pskb_may_pull() failure simply drops incoming skb, we might
fix this in a separate patch.
Signed-off-by: Eric Dumazet  <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Scott Feldman says:

====================
switchdev: documentation updates

Update the switchdev documentation to clarify that for IPV4 FIB object, the add
op is used for both adding and modifying the FIB entry on the device.

I found a few other white-space and grammer issues to fix, and to clarify the
static FDB ops.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Clarify in documentation and code that IPV4 FIB add operation is used for
both adding a new FIB entry to the device and for modifying an existing FIB
entry on the device.

Also, remove left-over references to ipv4_fib ops and replace with details
on SWITCHDEV_PORT_IPV4_FIB object.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2015-06-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
new driver mt7601u for MediaTek Wi-Fi devices MT7601U

ath10k:

* qca6174 power consumption improvements, enable ASPM etc (Michal)

wil6210:

* support Wi-Fi Simple Configuration in STA mode

iwlwifi:

* a few fixes (re-enablement of interrupts for certain new
  platforms that have special power states)
* Rework completely the RBD allocation model towards new
  multi RX hardware.
* cleanups
* scan reworks continuation (Luca)

mwifiex:

* improve firmware debug functionality

rtlwifi:

* update regulatory database

brcmfmac:

* cleanup and new feature support in PCIe code
* alternative nvram loading for router support
====================

Conflicts:
	drivers/net/wireless/iwlwifi/Kconfig

Trivial conflict in iwlwifi Kconfig, two commits adding
the same two chip numbers to the help text, but order
transposed.
Signed-off-by: David S. Miller <davem@davemloft.net>

Hariprasad Shenai says:

====================
cxgb4: Adds support for various ethtool stats

This patch series adds the following:
Adds support to dump adapter specific stats in ethtool
Adds support to dump channel stats in ethtool
Adds support to dump loopback port stats in ethtool
Remove wake-on-lan get/set ethtool support

This patch series has been created against net-next tree and includes
patches on cxgb4 driver.

We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove ethtool get/set support for wake on lan, adapter doesn't support
it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support in ethtool to dump loopback port statistics
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support in ethtool to dump adapter channel stats
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add ethtool support to get adapter specific hardware statistics
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Antonio Quartulli says:

====================
pull request: batman-adv 20150603

here you have our second batch of patches intended for net-next.

In this patchset you won't find any new features, but quite some code
cleanup work, a bunch of code style fixes and also comments corrections
by Markus Pargmann.

Moreover you have a patch from Sven Eckelmann removing an unnecessary
NULL check in batadv_iv_ogm_update_seqnos().

Please pull or let me know of any problem!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, two of the branches are dead code, since an earlier smaller
substring would have been found ("TP" in the "TP_NW" case and either
of "BNC" and "AUI" in the "BNC_AUI" case). Rearrange the strstr()
calls so that the longer strings are searched for first.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-06-03

This series contains updates to e1000e only.

Yanir provides 8 fixes and 1 version bump for e1000e.  First fix resolves
a possible unit hang if multiple descriptors are available in the rings
during reset or runtime suspend.  Fixed a warning on SPARC compile based
on a suggested solution from Alex Duyck.  Fixed a logical error, where
a "if" condition under which a flush should occur, was revered.  Fixed
a hardware issue that prevented i219 from working in legacy interrupts
mode.  Fixed the hardware clock configuration and suprious non-linear
increment.  Lastly, fixed a system hang which occurred during execution
of "ethtool -t <NIC>", by disabling MULR for the loopback test to avoid
the hand state.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow eBPF programs attached to classifier/actions to call
bpf_clone_redirect(skb, ifindex, flags) helper which will
mirror or redirect the packet by dynamic ifindex selection
from within the program to a target device either at ingress
or at egress. Can be used for various scenarios, for example,
to load balance skbs into veths, split parts of the traffic
to local taps, etc.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

fix typo in mlx4_set_vf_mac
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If mlx4_enable_sriov is called by adapter without this
feature MLX4_DEV_CAP_FLAG2_SYS_EQS then during this path the function alloc
icm is called twice without freeing the structures from the first time.
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If user loads mlx4_core with num_vfs greater than
supported then variable dev->dev_vfs is freed 2 times after unloading the
driver.
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This code in drivers/net/ethernet/dec/tulip/uli526x.c
function "uli526x_timer":

  1086          } else
  1087                  if ((tmp_cr12 & 0x3) && db->link_failed) {
  [...snip...]
  1109                  }
  1110                  else if(!(tmp_cr12 & 0x3) && db->link_failed)
  1111                  {
  [...snip...]
  1117                  }
  1118                  db->init=0;

is misleadingly indented: the
  db->init=0
is indented as if part of the else clause at line 1086, but it is
independent of it (no braces before the "if" at line 1087).

This patch fixes the indentation to reflect the actual meaning of the code,
though is it actually meant to be part of the "else" clause?  (I'm a
compiler developer, not a kernel person).  It also adds spaces around
the assignment, to placate checkpatch.pl.

Seen via an experimental new gcc warning I'm working on for gcc 6,
-Wmisleading-indentation, using gcc r223098 adding
-Werror=misleading-indentation to KBUILD_CFLAGS in Makefile.
The experimental GCC emits this warning (as an error), rightly IMHO:

drivers/net/ethernet/dec/tulip/uli526x.c: In function ‘uli526x_timer’:
drivers/net/ethernet/dec/tulip/uli526x.c:1118:3: error: statement is
indented as if it were guarded by... [-Werror=misleading-indentation]
   db->init=0;
    ^
drivers/net/ethernet/dec/tulip/uli526x.c:1086:4: note: ...this ‘else’
clause, but it is not
  } else
     ^

Hope this is helpful
Dave
Signed-off-by: David Malcolm <dmalcolm@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the TI dp83867 Gigabit ethernet phy
device.

The DP83867 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

use the time_after_eq macro for jiffies comparison operation
Signed-off-by: Antonio Murdaca <antonio.murdaca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When CONFIG_RFS_ACCEL or SMP aren't set, we fail to build, fix it.

Also, avoid build warning as of unused function on that setup.

Fixes: c66fa19c ('net/mlx4: Add EQ pool')
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove ret variable and all jumps.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>

We can avoid this indirect return variable by directly returning the
error values.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>

Declare the returntype of batadv_compare_eth as bool.
The function called inside this helper function
(ether_addr_equal_unaligned) also uses bool as return value, so there is
no need to return int.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>

It is much clearer to see a bool type as return value than 'int' for
functions that are supposed to return true or false.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>

orig_ifinfo is dereferenced multiple times in batadv_iv_ogm_update_seqnos
before the check for NULL is done. The function also exists at the
beginning when orig_ifinfo would have been NULL. This makes the check at
the end unnecessary and only confuses the reader/code analyzers.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>

batadv_orig_bat_iv->bcast_own is actually not a bitfield, it is an
array. Adjust the comment accordingly.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>

Bump the version to reflect the driver changes and bug fixes for i219.
Also update the copyright, while we are at it.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

System would hang during execution of "ethtool -t <NIC>" for the same
reason that required flushing the descriptor rings. This fix disables
MULR for the loopback test to avoid the hang state.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Two issues involving systim were reported.
1. Clock is not running in the correct frequency
2. In some situations, systim values were not incremented linearly
This patch fixes the hardware clock configuration and the spurious
non-linear increment.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This fix handles a hardware issue that prevented i219 from
working in legacy interrupts mode (IntMode=0)
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The indication that a descriptor ring flush is required was read from
FEXTNVM7 by mistake. It should be read from the PCI config space.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>