Mika Westerberg says:

====================
Thunderbolt networking

In addition of tunneling PCIe, Display Port and USB traffic, Thunderbolt
allows connecting two hosts (domains) over a Thunderbolt cable. It is
possible to tunnel arbitrary data packets over such connection using
high-speed DMA rings available in the Thunderbolt host controller.

In order to discover Thunderbolt services the other host supports, there is
a software protocol running on top of the automatically configured control
channel (ring 0). This protocol is called XDomain discovery protocol and it
uses XDomain properties to describe the host (domain) and the services it
supports.

Once both sides have agreed what services are supported they can enable
high-speed DMA rings to transfer data over the cable.

This series adds support for the XDomain protocol so that we expose each
remote connection as Thunderbolt XDomain device and each service as
Thunderbolt service device. On top of that we create an API that allows
writing drivers for these services and finally we provide an example
Thunderbolt service driver that creates virtual ethernet inferface that
allows tunneling networking packets over Thunderbolt cable. The API could
be used for creating other future Thunderbolt services, such as tunneling
SCSI over Thunderbolt, for example.

The XDomain protocol and networking support is also available in macOS and
Windows so this makes it possible to connect Linux to macOS and Windows as
well.

The patches are based on previous Thunderbolt networking patch series by
Amir Levy and Michael Jamet, that can be found here:

  https://lwn.net/Articles/705998/

The main difference to that patch series is that we have the XDomain
protocol running in the kernel now so there is no need for a separate
userspace daemon.

Note this does not affect the existing functionality, so security levels
and NVM firmware upgrade continue to work as before (with the small
exception that now sysfs also shows the XDomain connections and services in
addition to normal Thunderbolt devices). It is also possible to connect up
to 5 Thunderbolt devices and then another host, and the network driver
works exactly the same.

This is third version of the patch series. The previous versions can be
be found here:

  v2: https://lkml.org/lkml/2017/9/25/225
  v1: https://lwn.net/Articles/734019/

Changes from the v2:

  * Add comment regarding calculation of interrupt throttling value
  * Add UUIDs as strings in comments on top of each declaration
  * Add a patch removing __packed from existing ICM messages. They are all
    32-bit aligned and should pack fine without the __packed.
  * Move adding MAINTAINERS entries to a separate patches
  * Added Michael and Yehezkel to be maintainers of the network driver
  * Remove __packed from the new ICM messages. They should pack fine as
    well without it.
  * Call register_netdev() after all other initialization is done in the
    network driver.
  * Use build_skb() instead of copying. We allocate order 1 page here to
    leave room for SKB shared info required by build_skb(). However, we do
    not leave room for full NET_SKB_PAD because the NHI hardware does not
    cope well if a frame crosses 4kB boundary. According comments in
    __build_skb() that should still be fine.
  * Added Reviewed-by tag from Andy.

Changes from the v1:

  * Add include/linux/thunderbolt.h to MAINTAINERS
  * Correct Linux version and date of new sysfs entries in
    Documentation/ABI/testing/sysfs-bus-thunderbolt
  * Move network driver from drivers/thunderbolt/net.c to
    drivers/net/thunderbolt.c and update it to follow coding style in
    drivers/net/*.
  * Add MAINTAINERS entry for the network driver
  * Minor cleanups

In case someone wants to try this out, the last patch adds documentation
how the networking driver can be used. In short, if you connect Linux to a
macOS or Windows, everything is done automatically (as those systems have
the networking service enabled by default). For Linux to Linux connection
one host needs to load the networking driver first (so that the other side
can locate the networking service and load the corresponding driver).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

I will be maintaining the Thunderbolt network driver along with Michael
and Yehezkel.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ThunderboltIP is a protocol created by Apple to tunnel IP/ethernet
traffic over a Thunderbolt cable. The protocol consists of configuration
phase where each side sends ThunderboltIP login packets (the protocol is
determined by UUID in the XDomain packet header) over the configuration
channel. Once both sides get positive acknowledgment to their login
packet, they configure high-speed DMA path accordingly. This DMA path is
then used to transmit and receive networking traffic.

This patch creates a virtual ethernet interface the host software can
use in the same way as any other networking interface. Once the
interface is brought up successfully network packets get tunneled over
the Thunderbolt cable to the remote host and back.

The connection is terminated by sending a ThunderboltIP logout packet
over the configuration channel. We do this when the network interface is
brought down by user or the driver is unloaded.
Signed-off-by: Amir Levy <amir.jer.levy@intel.com>
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new API header (include/linux/thunderbolt.h) is maintained by the
Thunderbolt driver maintainers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Thunderbolt services should not care which HopID (ring) they use for
sending and receiving packets over the high-speed DMA path, so make
tb_ring_alloc_rx() and tb_ring_alloc_tx() accept negative HopID. This
means that the NHI will allocate next available HopID for the caller
automatically.

These HopIDs will be allocated from the range which is not reserved for
the Thunderbolt protocol (8 .. hop_count - 1).

The allocated HopID can be retrieved from ring->hop field after the ring
has been allocated successfully if needed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is needed when Thunderbolt service drivers need to DMA map memory
before it is passed down to the ring.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to support things like networking over Thunderbolt cable, there
needs to be a way to switch the ring to a mode where it can be polled
with the interrupt masked. We implement such mode so that the caller can
allocate a ring by passing pointer to a function that is then called
when an interrupt is triggered. Completed frames can be fetched using
tb_ring_poll() and the interrupt can be re-enabled when the caller is
finished with polling by using tb_ring_poll_complete().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is needed because ring polling functionality can be called from
atomic contexts when networking and other high-speed traffic is
transferred over a Thunderbolt cable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This makes it possible to enqueue frames also from atomic context which
is needed for example, when networking packets are sent over a
Thunderbolt cable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A Thunderbolt service driver might need to check if there was an error
with the descriptor when in frame mode. We also add two Rx specific
error flags RING_DESC_CRC_ERROR and RING_DESC_BUFFER_OVERRUN.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These are used by Thunderbolt services to send and receive frames over
the high-speed DMA rings.

We also put the functions to tb_ namespace to make sure we do not
collide with others and add missing kernel-doc comments for the exported
functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When high-speed DMA paths are used to transfer arbitrary data over a
Thunderbolt link, DMA rings should be in frame mode instead of raw mode.
The latter is used by the control channel (ring 0). In frame mode each
data frame can hold up to 4kB payload.

This patch modifies the DMA ring code to allow configuring a ring to be
in frame mode by passing a new flag (RING_FLAG_FRAME) to the ring when
it is allocated. In addition there might be need to enable end-to-end
(E2E) workaround for the ring to prevent losing Rx frames in certain
situations. We add another flag (RING_FLAG_E2E) that can be used for
this purpose.

This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This will keep the interrupt delivery rate reasonable. The value used
here (128 us) is a recommendation from the hardware people.

This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When two hosts are connected over a Thunderbolt cable, there is a
protocol they can use to communicate capabilities supported by the host.
The discovery protocol uses automatically configured control channel
(ring 0) and is build on top of request/response transactions using
special XDomain primitives provided by the Thunderbolt base protocol.

The capabilities consists of a root directory block of basic properties
used for identification of the host, and then there can be zero or more
directories each describing a Thunderbolt service and its capabilities.

Once both sides have discovered what is supported the two hosts can
setup high-speed DMA paths and transfer data to the other side using
whatever protocol was agreed based on the properties. The software
protocol used to communicate which DMA paths to enable is service
specific.

This patch adds support for the XDomain discovery protocol to the
Thunderbolt bus. We model each remote host connection as a Linux XDomain
device. For each Thunderbolt service found supported on the XDomain
device, we create Linux Thunderbolt service device which Thunderbolt
service drivers can then bind to based on the protocol identification
information retrieved from the property directory describing the
service.

This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A Thunderbolt service might need to find the physical port from a link
the cable is connected to. For instance networking driver uses this
information to generate MAC address according the Apple ThunderboltIP
protocol.

Move this function to thunderbolt.h and rename it to
tb_phy_port_from_link() to reflect the fact that it does not take switch
as parameter.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These are needed by Thunderbolt services so move them to thunderbolt.h
to make sure they are available outside of drivers/thunderbolt.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These will be needed by Thunderbolt services when sending and receiving
XDomain control messages. While there change TB_CFG_PKG_PREPARE_TO_SLEEP
value to be decimal in order to be consistent with other members.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Thunderbolt XDomain discovery protocol uses directories which contain
properties and other directories to exchange information about what
capabilities the remote host supports. This also includes identification
information like device ID and name.

This adds support for parsing and formatting these properties and
establishes an API drivers can use in addition to the core Thunderbolt
driver. This API is exposed in a new header: include/linux/thunderbolt.h.

This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These messages are all 32-bit aligned and they should be packed without
the __packed attribute just fine. It also allows compiler to generate
better code on some architectures.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We will be using these when communicating XDomain discovery protocol
over Thunderbolt link but they might be useful for other drivers as
well.

Make them available through byteorder/generic.h.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: Fixlets

Couple of small nit fixes from Petr
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fou test lifted from ip-fou man page.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Horman says:

====================
flow_dissector: dissect tunnel info

Move dissection of tunnel info from the flower classifier to the flow
dissector where all other dissection occurs.  This should not have any
behavioural affect on other users of the flow dissector.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Move dissection of tunnel info from the flower classifier to the flow
dissector where all other dissection occurs.  This should not have any
behavioural affect on other users of the flow dissector.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the skb parameter of skb_metadata_dst() and skb_tunnel_info()
const as they are not modified. This is in preparation for using
them in call-sites where skb is const.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make local functions static to fix

  HOSTCC  samples/bpf/xdp_monitor_user.o
samples/bpf/xdp_monitor_user.c:64:7: warning: no previous prototype for ‘gettime’ [-Wmissing-prototypes]
 __u64 gettime(void)
       ^~~~~~~
samples/bpf/xdp_monitor_user.c:209:6: warning: no previous prototype for ‘print_bpf_prog_info’ [-Wmissing-prototypes]
 void print_bpf_prog_info(void)
      ^~~~~~~~~~~~~~~~~~~
Fixes: 3ffab546 ("samples/bpf: xdp_monitor tool based on tracepoints")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the unlikely event that mfc->mfc_un.res.ttls[i] is 255 for all
values of i from 0 to MAXIVS-1, the err is not set at all and hence
has a garbage value on the error return at the end of the function,
so initialize it to 0.  Also, the error return check on err and goto
to err: inside the for loop makes it impossible for err to be zero
at the end of the for loop, so we can remove the redundant err check
at the end of the loop.

Detected by CoverityScan CID#1457207 ("Unitialized scalar value")

Fixes: c011ec1b ("mlxsw: spectrum: Add the multicast routing offloading logic")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jonas Gorski says:

====================
bcm63xx_enet: small fixes and cleanups

This patch set fixes a few theoretical issues and cleans up the code a
bit. It also adds a bit more managed function usage to simplify clock
and iomem usage.

Based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We don't use anyhing from that file, so drop it.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

clk_disable and clk_unprepare are NULL-safe, so need to duplicate the
NULL check of the functions.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use managed functions where possible to reduce the amount of resource
handling on error and remove paths.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not rely on the shared device being probed before the enet(sw)
devices. This makes it easier to eventually move out the shared
device as a dma controller driver (what it should be).
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The DMA controller regs actually point to DMA channel 0, so the write to
ENETDMA_CFG_REG will actually modify a random DMA channel.

Since DMA controller registers do not exist on BCM6345, guard the write
with the usual check for dma_has_sram.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check the return code of prepare_enable and change one last instance of
enable only to prepare_enable. Also properly disable and release the
clock in error paths and on remove for enetsw.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function is unused, and furthermore it is buggy since it suffers
from the same issue that requires IP6_ECN_set_ce() to take a pointer
to the skb so that it may (in case of CHECKSUM_COMPLETE) update skb->csum

Instead of fixing it, let's just outright remove it.

Tested: builds, and 'git grep IP6_ECN_clear' comes up empty
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Different namespace application might require different time period in
second to disable Fastopen on active TCP sockets.

Tested:
Simulate following similar situation that the server's data gets dropped
after 3WHS.
C ---- syn-data ---> S
C <--- syn/ack ----- S
C ---- ack --------> S
S (accept & write)
C?  X <- data ------ S
	[retry and timeout]

And then print netstat of TCPFastOpenBlackhole, the counter increased as
expected when the firewall blackhole issue is detected and active TFO is
disabled.
# cat /proc/net/netstat | awk '{print $91}'
TCPFastOpenBlackhole
1
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Different namespace application might require different tcp_fastopen_key
independently of the host.

David Miller pointed out there is a leak without releasing the context
of tcp_fastopen_key during netns teardown. So add the release action in
exit_batch path.

Tested:
1. Container namespace:
# cat /proc/sys/net/ipv4/tcp_fastopen_key:
2817fff2-f803cf97-eadfd1f3-78c0992b

cookie key in tcp syn packets:
Fast Open Cookie
    Kind: TCP Fast Open Cookie (34)
    Length: 10
    Fast Open Cookie: 1e5dd82a8c492ca9

2. Host:
# cat /proc/sys/net/ipv4/tcp_fastopen_key:
107d7c5f-68eb2ac7-02fb06e6-ed341702

cookie key in tcp syn packets:
Fast Open Cookie
    Kind: TCP Fast Open Cookie (34)
    Length: 10
    Fast Open Cookie: e213c02bf0afbc8a
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 'publish' logic is not necessary after commit dfea2aa6 ("tcp:
Do not call tcp_fastopen_reset_cipher from interrupt context"), because
in tcp_fastopen_cookie_gen，it wouldn't call tcp_fastopen_init_key_once.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>