- 15 Mar, 2014 40 commits
-
-
Vikas Chaudhary authored
Signed-off-by:
Vikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
James Bottomley <JBottomley@Parallels.com>
-
Vikas Chaudhary authored
Signed-off-by:
-
Nilesh Javali authored
Issue: For ISP8xxx, adapter initialization is not retried if qla4xxx_initialize_adapter fails. Fix: If qla4xxx_initialize_adapter fails, first check if failure is due to IRQs not attached in order to skip retrial, then free the IRQs and then retry initializing the adapter. Signed-off-by:
Nilesh Javali <nilesh.javali@qlogic.com> Signed-off-by:
-
Jayamohan Kallickal authored
Signed-off-by:
John Soni Jose <sony.john-n@emulex.com> Signed-off-by:
Jayamohan Kallickal <jayamohan.kallickal@emulex.com> Signed-off-by:
-
Jayamohan Kallickal authored
Setting DMA bit mask 64 and roll back to 32 if not supported. Signed-off-by:
Minh Tran <minhduc.tran@emulex.com> Signed-off-by:
-
Jayamohan Kallickal authored
scsi_cmnd n io_task was not NULL when - Link goes down while IO was happening and session is closed. - Task for which TMF was sent. Signed-off-by:
-
Jayamohan Kallickal authored
In iSCSI Boot scenario, when machine is reboot/shutdown phase the active sessions are not closed. Driver queue cleanup is done as part of unload and device is disabled. Sessions are still active, iSCSI commands are issued from session which comes to driver, as driver cleanup and device disabled there is kernel stack dump with errors. Fix is invoking iscsi_session_failure with ISCSI_ERR_INVALID_HOST on all the active sessions when shutdown routine is called. Signed-off-by:
-
Jayamohan Kallickal authored
The doorbel format has been updated to support additonal functionalities of SKH-R adapter. These changes are made such that older FW also works fine. Signed-off-by:
-
Jayamohan Kallickal authored
The 100Mbps port speed macro used was not proper. Signed-off-by:
-
Jayamohan Kallickal authored
When an MBX command timeout happens,the resources associated with the MBX command were freed. If FW were to give the response to host after the timeout value set by driver then driver crashes as the MBX Cmd resources were already freed. This patch fixes this issue by maintaing a state flag for each of the MBX command posted/timedout/completed. Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
Scott Teel <scott.teel@hp.com> Signed-off-by:
-
Stephen M. Cameron authored
On encountering unexpected error conditions from driver initiated commands, print something useful like CDB and sense data rather than something useless like the kernel virtual address of the command buffer. Signed-off-by:
-
Stephen M. Cameron authored
Do no rescan on every events -- way too many rescans are triggered if we don't filter the events. Limit rescans to be triggered by the following set of events: * controller state change * enclosure hot plug * physical drive state change * logical drive state change * redundant controller state change * accelerated io enabled/disabled * accelerated io configuration change Signed-off-by:
-
Stephen M. Cameron authored
Don't wait for *all* commands to complete, only for accelerated mode commands. Signed-off-by:
-
Scott Teel authored
Add controller-based data-at-rest encryption compatibility to ioaccel2 path (HP SSD Smart Path). Encryption feature requires driver to supply additional fields for encryption enable, tweak index, and data encryption key index in the ioaccel2 request structure. Encryption enable flag and data encryption key index come from raid_map data structure from raid offload command. During ioaccel2 submission, check device structure's raid map to see if encryption is enabled for the device. If so, call new function below. Add function set_encrypt_ioaccel2 to set encryption flag, data encryption key index, and calculate tweak value from request's logical block address. Signed-off-by:
-
Scott Teel authored
Signed-off-by:
-
Scott Teel authored
Change the handling of HP SSD Smart Path errors with status: 0x02 CHECK CONDITION 0x08 BUSY 0x18 RESERVATION CONFLICT 0x40 TASK ABORTED So that they get retried on the RAID Path. Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Code was confused and assumed that page zero was not VPD page and all non-zero pages were VPD pages. Signed-off-by:
-
Scott Teel authored
Allow driver to schedule a rescan whenever a request fails on the ioaccel2 path. This eliminates the possibility of driver getting stuck in non-ioaccel mode. IOaccel mode (HP SSD Smart Path) is disabled by driver upon error detection. Driver relied on idea that request would be retried through normal path, and a subsequent error would occur on that path, and be processed by controller firmware. As part of that process, controller disables ioaccel mode and later reinstates it, signalling driver to change modes. In some error cases, the error will not duplicate on the standard path, so the driver could get stuck in non-ioaccel mode. To avoid that, we allow driver to request a rescan during the next run of the rescan thread. Signed-off-by:
-
Scott Teel authored
Allow SSD Smart Path for a controller to be disabled by the user, regardless of settings in controller firmware or array configuration. To disable: echo 0 > /sys/class/scsi_host/host<id>/acciopath_status To re-enable: echo 1 > /sys/class/scsi_host/host<id>/acciopath_status To check state: cat /sys/class/scsi_host/host<id>/acciopath_status Signed-off-by:
-
Scott Teel authored
Load balance across members of a N-way mirror set, and handle the meta-RAID levels: R10, R50, R60. Signed-off-by:
-
Stephen M. Cameron authored
Otherwise we could wind up using incorrect raid map data, and then very bad things would likely happen. Signed-off-by:
-
Scott Teel authored
Underlying firmware cannot handle task abort on accelerated path (SSD Smart Path). Change abort requests for accelerated path commands to physical target reset. Send reset request on normal IO path. Signed-off-by:
Mike Miller <michael.miller@canonical.com> Signed-off-by:
-
Scott Teel authored
Signed-off-by:
-
Scott Teel authored
Signed-off-by:
Joe Handzik <Joseph.T.Handzik@hp.com> Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Mike MIller authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Mike Miller authored
Signed-off-by:
-
Scott Teel authored
Signed-off-by:
-
Scott Teel authored
Signed-off-by:
-
Stephen M. Cameron authored
* Do not check event bits on locked up controllers to see if they need to be rescanned. * Do not initiate any device rescans on controllers which are known to be locked up. Signed-off-by:
-
Stephen M. Cameron authored
For shared SAS configurations, hosts need to poll Smart Arrays periodically in order to be able to detect configuration changes such as logical drives being added or removed from remote hosts. A register on the controller indicates when such events have occurred, and the driver polls the register via a workqueue and kicks off a rescan of devices if such an event is detected. Additionally, changes to logical drive raid offload eligibility are autodetected in this way. Signed-off-by:
-
Stephen M. Cameron authored
When rescanning for logical drives, store information about whather raid offload is enabled for each logical drive, and update the driver's internal record of this. Signed-off-by:
-
Stephen M. Cameron authored
This enables sending i/o's destined for RAID logical drives which can be serviced by a single physical disk down a different, faster i/o path directly to physical drives for certain logical volumes on SSDs bypassing the Smart Array RAID stack for a performance improvement. Signed-off-by:
Matt Gates <matthew.gates@hp.com> Signed-off-by:
Don Brace <brace@beardog.cce.hp.com> Signed-off-by:
-
Scott Teel authored
For "mode 1" io accelerated commands, the command tag is in a different location than for commands that go down the normal RAID path, so the abort handler needs to take this into account. Signed-off-by:
-
