Starting from Spectrum-4, the maximum number of LAG IDs can be configured
by software via CONFIG_PROFILE command during driver initialization.

Add a dedicated instance of 'struct mlxsw_config_profile' for Spectrum-4
and set the 'max_lag' field to 128, which is the same amount of LAG entries
as in Spectrum-{2,3}. Without this configuration, firmware reserves 256
(the value of 'cap_max_lag' resource) entries at beginning of PGT table for
LAG identifiers, which means that less entries in PGT will be available.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Currently the driver queries the maximum supported LAG ID from firmware.
This will not be accurate anymore once the driver will configure 'max_lag'
via CONFIG_PROFILE command.

For resource query, firmware returns the maximum LAG ID which is supported
by hardware. Software can configure firmware to do not allocate entries for
all the supported LAGs, and to limit LAG IDs. In this case, the resource
query will not return the actual maximum LAG ID.

Add a helper function for getting this value. In case that 'max_lag' field
was set during initialization, return the value which was used, otherwise,
query firmware for the maximum supported ID.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In the device, LAG identifiers are stored in the port group table (PGT).
During initialization, firmware reserves a certain amount of entries at
the beginning of this table for LAG identifiers.

In Spectrum-4, the size of the PGT table did not increase, but the maximum
number of LAG identifiers was doubled, leaving less room for others entries
(e.g., flood entries) that also reside in the PGT.

Therefore, in order to avoid a regression and as long as there is no
explicit requirement to support 256 LAGs, mlxsw driver will configure the
firmware to allocate the same amount of LAG entries (128) as in
Spectrum-{2,3}. This configuration is done using 'max_lag' field in
CONFIG_PROFILE command. Extend 'struct mlxsw_config_profile' to support
'max_lag' field and configure firmware accordingly.

A next patch will adjust Spectrum-4 to configure 'max_lag' field.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Starting from Spectrum-4, the maximum number of LAG IDs can be configured
by software via CONFIG_PROFILE command during driver initialization.

Edit the comment of 'max_lag' field to mention that this field is reserved
in Spectrum-1/2/3 and describe firmware behavior.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

tlb_dynamic_lb bonding option is compatible with balance-tlb and balance-alb
modes. In order to be consistent with other option documentation, it should
mention both modes not only balance-tlb.
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20220826154738.4039-1-ffmancera@riseup.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

These error paths return success but they should return -ENOMEM.

Fixes: 01328e23 ("mlxsw: minimal: Extend module to port mapping with slot index")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/YwjgwoJ3M7Kdq9VK@kiliSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Clang warns:

  drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:481:6: error: variable 'err' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
          if (IS_ERR(flow_rule)) {
              ^~~~~~~~~~~~~~~~~
  drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:489:9: note: uninitialized use occurs here
          return err;
                ^~~
  drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:481:2: note: remove the 'if' if its condition is always true
          if (IS_ERR(flow_rule)) {
          ^~~~~~~~~~~~~~~~~~~~~~~
  drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:474:9: note: initialize the variable 'err' to silence this warning
          int err;
                ^
                  = 0
  1 error generated.

There is little reason to have the 'goto + error variable' construct in
this function. Get rid of it and just return the PTR_ERR value in the if
statement and 0 at the end.

Fixes: 430e2d5e ("net/mlx5: E-Switch, Move send to vport meta rule creation")
Link: https://github.com/ClangBuiltLinux/linux/issues/1695Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20220825180607.2707947-1-nathan@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Once devlink port is successfully registered, the devlink pointer is not
NULL. Therefore, the check is going to be always true and therefore
pointless. Remove it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Dimitris Michailidis <dmichail@fungible.com>
Link: https://lore.kernel.org/r/20220826110411.1409446-1-jiri@resnulli.usSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Arınç ÜNAL says:

====================
completely rework mediatek,mt7530 binding

This patch series brings complete rework of the mediatek,mt7530 binding.

The binding is checked with "make dt_binding_check
DT_SCHEMA_FILES=mediatek,mt7530.yaml".

If anyone knows the GIC bit for interrupt for multi-chip module MT7530 in
MT7623AI SoC, let me know. I'll add it to the examples.

If anyone got a Unielec U7623 or another MT7623AI board, please reach out.
====================

Link: https://lore.kernel.org/r/20220825082301.409450-1-arinc.unal@arinc9.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Update the description of the binding.

- Describe the switches, which SoCs they are in, or if they are standalone.
- Explain the various ways of configuring MT7530's port 5.
- Remove phy-mode = "rgmii-txid" from description. Same code path is
followed for delayed rgmii and rgmii phy-mode on mtk_eth_soc.c.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Define acceptable phy-mode values for the CPU ports of mt7530 and mt7531
switches. Remove relevant information from the description of the binding.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Update the examples on the binding.

- Add examples which include a wide variation of configurations.
- Make example comments YAML comment instead of DT binding comment.
- Add interrupt controller to the examples. Include header file for
interrupt.
- Change reset line for MT7621 examples.
- Pretty formatting for the examples.
- Change switch reg to 0.
- Change port labels to fit the example, change port 4 label to wan.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

- Add description for reset-gpios.
- Invalidate reset-gpios if mediatek,mcm is used. We cannot use multiple
reset lines at the same time.
- Invalidate mediatek,mcm if the compatible device is mediatek,mt7531.
There is no multi-chip module version of mediatek,mt7531.
- Require mediatek,mcm for mediatek,mt7621 as the compatible string is only
used for the multi-chip module version of MT7530.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fix the description of mediatek,mcm. mediatek,mcm is not used on MT7623NI.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Make trivial changes on the binding.

- Update title to include MT7531 switch.
- Add me as a maintainer. List maintainers in alphabetical order by first
name.
- Add description to compatible strings.
- Stretch descriptions up to the 80 character limit.
- Remove lists for single items.
- Remove requiring reg as it's already required by dsa-port.yaml.
- Define acceptable reg values for the CPU ports.
- Remove quotes from $ref: "dsa.yaml#".
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Follow-up the removal of unused internal api of port params made by
commit 42ded61a ("devlink: Delete not used port parameters APIs")
and stub the commands and add extack message to tell the user what is
going on.

If later on port params are needed, could be easily re-introduced,
but until then it is a dead code.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20220826082730.1399735-1-jiri@resnulli.usSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Using TCQ_MIN_PRIO_BANDS instead of magic number in prio_tune().
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Link: https://lore.kernel.org/r/20220826041035.80129-1-shaozhengchao@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Add build options and guidance doc.
Initialize pci device access for Wangxun Gigabit Ethernet devices.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Link: https://lore.kernel.org/r/20220826034609.51854-1-mengyuanlou@net-swift.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Jakub Kicinski says:

====================
netlink: support reporting missing attributes

This series adds support for reporting missing attributes
in a structured way. We communicate the type of the missing
attribute and if it was missing inside a nest the offset
of that nest.

Example of (YAML-based) user space reporting ethtool header
missing:

 Kernel error: missing attribute: .header

I was tempted to integrate the check with the policy
but it seems tricky without doing a full scan, and there
may be a ton of attrs in the policy. So leaving that
for later.
====================

Link: https://lore.kernel.org/r/20220826030935.2165661-1-kuba@kernel.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The actual presence check for the header is in
ethnl_parse_header_dev_get() but it's a few layers in,
and already has a ton of arguments so let's just pick
the low hanging fruit and check for missing header in
the default request handler.
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Strset needs ETHTOOL_A_STRINGSET_ID, use it as an example of
reporting attrs missing in nests.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Devlink with its global attr policy has a lot of attribute
presence check, use the new ext ack reporting when they are
missing.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Being able to check attribute presence and set extack
if not on one line is handy, add helpers.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

There is currently no way to report via extack in a structured way
that an attribute is missing. This leads to families resorting to
string messages.

Add a pair of attributes - @offset and @type for machine-readable
way of reporting missing attributes. The @offset points to the
nest which should have contained the attribute, @type is the
expected nla_type. The offset will be skipped if the attribute
is missing at the message level rather than inside a nest.

User space should be able to figure out which attribute enum
(AKA attribute space AKA attribute set) the nest pointed to by
@offset is using.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The ext_ack writing code looks very "organically grown".
Move the calculation of the size and writing out to helpers.
This is more idiomatic and gives us the ability to return early
avoiding the long (and randomly ordered) "if" conditions.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Consolidate alloclen and pagedlen calculation for zerocopy and normal
paged requests. The current non-zerocopy paged version can a bit
overallocate and unnecessary copy a small chunk of data into the linear
part.

Cc: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/netdev/CA+FuTSf0+cJ9_N_xrHmCGX_KoVCWcE0YQBdtgEkzGvcLMSv7Qw@mail.gmail.com/Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/b0e4edb7b91f171c7119891d3c61040b8c56596e.1661428921.git.asml.silence@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Simon Horman says:

====================
nfp: port speed and eeprom get/set updates

this short series is the initial updates for the NFP driver for the v6.1
Kernel. It covers two enhancements:

1. Patches 1/3 and 2/3:
   - Support cases where application firmware does not know port speeds
     a priori by relaying this information from the management firmware
     to the application firmware.

     This allows the existing mechanism, whereby the driver reports port
     speeds to user-space as provided by the application firmware, to work
     in this case.

2. Patch 2/3:
   - Add support for eeprom get and set command
====================

Link: https://lore.kernel.org/r/20220825141223.22346-1-simon.horman@corigine.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Add support for eeprom get and set operation with ethtool command.
with this change, we can support commands as:

 #ethtool -e enp101s0np0 offset 0 length 6
 Offset          Values
 ------          ------
 0x0000:         00 15 4d 16 66 33

 #ethtool -E enp101s0np0 magic 0x400019ee offset 5 length 1 value 0x88

We make this change to persist MAC change during driver reload and system
reboot.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

A new tlv type is introduced to indicate if application firmware is
indifferent to port speed, and inform management firmware of the
result.

And the result is always true for flower application firmware since
it's indifferent to port speed from the start and will never change.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

In future releases the NIC application firmware may be indifferent to port
speeds - not built for specific port speeds - and consequently it will not
be able to report VF port speeds to the driver without first learning them.
With this change, the driver will pass the speed of physical ports from
management firmware to application firmware, and the latter will copy the
speed of port 0 to all the active VFs. So that the driver can get VF port
speed as before.

The port speed of a VF may be requested from userspace using:

  ethtool <vf-intf>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Casper Andersson says:

====================
net: sparx5: add mrouter support

This series adds support for multicast router ports to SparX5. To manage
mrouter ports the driver must keep track of mdb entries. When adding an
mrouter port the driver has to iterate over all mdb entries and modify
them accordingly.

v2:
- add bailout in free_mdb
- re-arrange mdb struct to avoid holes
- change devm_kzalloc -> kzalloc
- change GFP_ATOMIC -> GFP_KERNEL
- fix spelling
====================
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All multicast should be forwarded to mrouter ports. Mrouter ports must
therefore be part of all active multicast groups, and override flooding
from being disabled.
Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Keep track of all mdb entries in software for easy access.
Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IP multicast must sometimes be discriminated from non-IP multicast,
e.g. when determining the forwarding behavior of a given group in the
presence of multicast router ports on an offloaded bridge. Therefore,
provide helpers to identify these groups.
Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We had historically not checked that genlmsghdr.reserved
is 0 on input which prevents us from using those precious
bytes in the future.

One use case would be to extend the cmd field, which is
currently just 8 bits wide and 256 is not a lot of commands
for some core families.

To make sure that new families do the right thing by default
put the onus of opting out of validation on existing families.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Paul Moore <paul@paul-moore.com> (NetLabel)
Signed-off-by: David S. Miller <davem@davemloft.net>

We no longer allow "handle" to be zero, so there is no need to check
for that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/Ywd4NIoS4aiilnMv@kiliSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The "fixed_link" is only allocated sometimes but it's freed
unconditionally in the error handling.  Set it to NULL so we don't free
uninitialized data.

Fixes: 9ea4742a ("net: fman: Configure fixed link in memac_initialization")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/Ywd2X6gdKmTfYBxD@kiliSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Andrey Zhadchenko says:

====================
openvswitch: allow specifying ifindex of new interfaces

CRIU currently do not support checkpoint/restore of OVS configurations, but
there was several requests for it. For example,
https://github.com/lxc/lxc/issues/2909

The main problem is ifindexes of newly created interfaces. We realy need to
preserve them after restore. Current openvswitch API does not allow to
specify ifindex. Most of the time we can just create an interface via
generic netlink requests and plug it into ovs but datapaths (generally any
OVS_VPORT_TYPE_INTERNAL) can only be created via openvswitch requests which
do not support selecting ifindex.

This patch allows to do so.
For new datapaths I decided to use dp_infindex in header as infindex
because it control ifindex for other requests too.
For internal vports I reused OVS_VPORT_ATTR_IFINDEX.

The only concern I have is that previously dp_ifindex was not used for
OVS_DP_VMD_NEW requests and some software may not set it to zero. However
we have been running this patch at Virtuozzo for 2 years and have not
encountered this problem. Not sure if it is worth to add new
ovs_datapath_attr instead.
====================

Link: https://lore.kernel.org/r/20220825020450.664147-1-andrey.zhadchenko@virtuozzo.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

CRIU needs OVS_DP_ATTR_PER_CPU_PIDS to checkpoint/restore newest
openvswitch versions.
Add pids to generic datapath reply. Limit exported pids amount to
nr_cpu_ids.
Signed-off-by: Andrey Zhadchenko <andrey.zhadchenko@virtuozzo.com>
Acked-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

CRIU is preserving ifindexes of net devices after restoration. However,
current Open vSwitch API does not allow to target ifindex, so we cannot
correctly restore OVS configuration.

Add new OVS_DP_ATTR_IFINDEX for OVS_DP_CMD_NEW and use it as desired
ifindex.
Use OVS_VPORT_ATTR_IFINDEX during OVS_VPORT_CMD_NEW to specify new netdev
ifindex.
Signed-off-by: Andrey Zhadchenko <andrey.zhadchenko@virtuozzo.com>
Acked-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>