Add LCDC pin definitions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>

Define the HLCDC (HLCD Controller) IP available on some sama5d3 SoCs
(i.e. sama5d31, sama5d33, sama5d34 and sama5d36) in sama5d3 dtsi file.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Anthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Define alternative pin muxing for the LCDC pins.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Anthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The HLCDC (HLCD Controller) IP supports 4 different output mode (RGB444,
RGB565, RGB666 and RGB888) and the pin muxing will depend on the chosen
RGB mode.

Split pin definitions to be able to set pin config according to the
selected mode.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Anthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Enable RTC for all the at91sam9x5 CPU Modules: this will enable it for all the
EK boards.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This drivers allows a fixed framebuffer memory to be set by an additional
IORESOURCE_MEM resource. Thus add an example to the DT documentation.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add ISI dt node and pinctrl settings in sama5d4.dtsi.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[nicolas.ferre@atmel.com: sort nodes in order. remove useless comments]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Enable audio support for sama5d4ek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add wm8904 codec node and enable it.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Enable SSC0 node, which will be used for audio.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add SSC 0 and 1 nodes.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add i2c0 aka twi0 on sama5d4 xplained board.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add at91 sama5d4 xplained board support.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

macb0 DT node can have phy child nodes, so add the #{address,
size}_cells for macb0 node.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add the leds DT node in the dts file.
In the leds, d10 is set as heartbeat led.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add alias, node declaration and pinctrl for i2c1 (aka: twi1).
Signed-off-by: Philip Attfield <phil.attfield@seqlabs.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Gpio-keys nodes are not using the "reg" property in their sub nodes.
So, there is no need to define #address-cells and #size-cells properties
in gpio-keys nodes: we remove them in these new boards.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

File name had at91 prefix, which is not the case anymore for SAMA5D3.
AT91SAM9x5 was mentioned instead of SAMA5D3 SoC.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Enable usb device port on at91sam9n12ek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add usb device node for at91sam9n12.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Enable ISI and ov2640 for at91sam9g25ek board.
Meantime, we need to disable the mmc1 and spi0 as they have pin conflict
with ISI.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add the camera sensor ov2640 dt support. And connect sensor to isi node
as well.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add a new file: at91sam9x5_isi.dtsi, which includes ISI node and
pinctrls.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

First fixes batch for AT91 on 4.0:
- PM slowclock fixes for DDR and timeouts
- fix some DT entries
- little defconfig updates
- the removal of a harmful watchdog option + its detailed documentation

Since turning on idle-halt in commit fe46aa67 (ARM: at91/dt: add
sam9 watchdog default options to SoCs), SoCs compatible with at91sam9260-wdt
no longer reboot if the watchdog times out while the CPU is in idle state.
Removing the 'idle-halt' flag that was set by default fixes this.
Signed-off-by: Michel Marti <mma@objectxp.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
[nicolas.ferre@atmel.com: rework the commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

atmel,idle-halt property should be used with care, it actually makes the
watchdog not counting when the CPU is in idle state, therefore the
watchdog reset time depends on mean CPU usage and will not reset at all
of the CPU stop working while it is in idle state, which is probably not
what you want.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

There is now only one defconfig for the at91rm9200 and at91sam9. Add ethernet
support for the at91rm9200.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Recent distributions and userspace tools after 2009/2010 depend on
the existence of /sys/class/block/, and will not work with this option enabled.
Signed-off-by: Anthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Corrected pins used by usart3.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Commit ff04660e48b20 ("ARM: at91/dt: add SRAM nodes") used the same base
address for sram0 and sram1 leading to the following warning:
WARNING: CPU: 0 PID: 1 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x50/0x70()
sysfs: cannot create duplicate filename '/devices/platform/300000.sram'
Fix the base address for sram1.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

On some platforms, there are multiple SRAM nodes defined in the device tree but
some of them are disabled, leading to allocation failure. Try to find the first
enabled SRAM node and allocate from it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

at91rm9200 standby and suspend to ram has been broken since
00482a40. It is wrongly using AT91_BASE_SYS which is a physical address
and actually doesn't correspond to any register on at91rm9200.

Use the correct at91_ramc_base[0] instead.

Fixes: 00482a40 (ARM: at91: implement the standby function for pm/cpuidle)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The DDRSDR controller fails miserably to put LPDDR1 memories in
self-refresh. Force the controller to think it has DDR2 memories
during the self-refresh period, as the DDR2 self-refresh spec is
equivalent to LPDDR1, and is correctly implemented in the
controller.

Assume that the second controller has the same fault, but that is
untested.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>