This works around a few glitches in the ST version of the PL011
serial driver when using very high baud rates, as we do in the
Ux500: 3, 3.25, 4 and 4.05 Mbps.

Problem Observed/rootcause:

When using high baud-rates, and the baudrate*8 is getting close to
the provided clock frequency (so a division factor close to 1), when
using bursts of characters (so they are abutted), then it seems as if
there is not enough time to detect the beginning of the start-bit which
is a timing reference for the entire character, and thus the sampling
moment of character bits is moving towards the end of each bit, instead
of the middle.

Fix:
Increase slightly the RX baud rate of the UART above the theoretical
baudrate by 5%. This will definitely give more margin time to the
UART_RX to correctly sample the data at the middle of the bit period.

Also fix the ages old copy-paste error in the very stressed comment,
it's referencing the registers used in the PL010 driver rather than
the PL011 ones.
Signed-off-by: Guillaume Jaunet <guillaume.jaunet@stericsson.com>
Signed-off-by: Christophe Arnal <christophe.arnal@stericsson.com>
Signed-off-by: Matthias Locher <matthias.locher@stericsson.com>
Signed-off-by: Rajanikanth HV <rajanikanth.hv@stericsson.com>
Cc: stable <stable@vger.kernel.org>
Cc: Bibek Basu <bibek.basu@stericsson.com>
Cc: Par-Gunnar Hjalmdahl <par-gunnar.hjalmdahl@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The kernel will handle IXON/IXOFF/IXANY in software if the hardware
doesn't do it.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The following patch allows users to use KGDB over serial console on
board based on Samsung SOC. It has been tested on a board using
exynos5.

[dianders: changed poll to return NO_POLL_CHAR, which appears to
fix 'help' in kgdb; also updated commit message]
Signed-off-by: Julien Pichon <pichon.jln@gmail.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MAXIDL is the timeout after which a receive buffer is closed when not full if
no more characters are received. We calculate it from the baudrate so that the
duration is always the same at standard rates: about 4ms. At 9600 bauds it gives
a timeout of 4 characters, which is the timeout on the 8250 UART.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

maxidl register was set to fifo size. There is no reason to set this
register to same value as fifo size. Setting it now to 0x10 by default
as in the UCC UART driver.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Setting the fifo to only 1 byte generates one interrupt every 1ms at 9600 bauds.
This is too much. This patch reduces the threshold to speeds below 2400 bauds
like in the 8250 UART driver.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes a desynchronisation problem with CPM UART driver on
Powerpc MPC8xx. The problem happens if data is received before the device
is open by the user application.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Apparently the same card model has two IDs, so this patch
complements the commit 39aced68
adding the missing one.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch does the following
- In case of errors if there least one data character in the RX FIFO
read it otherwise it may stall the receiver.

This is recommended in the interrupt reset method in the table 23-246 of
the omap4 TRM.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The legacy serial driver will detect the Winbond CIR device as a serial
port, since it looks exactly like a serial port unless you know what
it is from the PNP ID.

Here we track this port as a special PORT_8250_CIR type, preventing the
legacy serial driver from probing it.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We first probe the legacy serial ports and then check pnp. If there
is a non-standard configuration then this might not work, also this
change is needed so we can blacklist Winbond CIR based on PNP ID.

For this to work the 8250_pnp driver must be merged into the 8250
module.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In dgrp_receive() there is:

   desclen = ((plen - 12) > MAX_DESC_LEN) ? MAX_DESC_LEN :
   	     	      	    plen - 12;
   strncpy(nd->nd_ps_desc, b + 12, desclen);

However, it's possible for plen to be <= 12 here so we'd be passing a
negative number into the strncpy().  Fix this to not make the strncpy
call and report an error if desclen is <= 0
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Wrap the use of TIOCSRS485 and TIOCGRS485 in #ifdef so that we avoid
adding undefined IOCTLs to the ioctl pointer list as compatible
ioctls.

This change was motivated by a build error on a MIPS build.

tree:   git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty.git
tty-next
head:   ac57e7f3
commit: 84c3b848 [10/16] compat_ioctl:
  Add RS-485 IOCTLs to the list
config: mips-fuloong2e_defconfig

All related error/warning messages:

fs/compat_ioctl.c:869:1: error: 'TIOCSRS485' undeclared here (not in a
  function)
fs/compat_ioctl.c:870:1: error: 'TIOCGRS485' undeclared here (not in a
  function)

vim +869 fs/compat_ioctl.c
863 COMPATIBLE_IOCTL(TIOCSPGRP)
864 COMPATIBLE_IOCTL(TIOCGPGRP)
865 COMPATIBLE_IOCTL(TIOCGPTN)
866 COMPATIBLE_IOCTL(TIOCSPTLCK)
867 COMPATIBLE_IOCTL(TIOCSERGETLSR)
868 COMPATIBLE_IOCTL(TIOCSIG)
> 869 COMPATIBLE_IOCTL(TIOCSRS485)
870 COMPATIBLE_IOCTL(TIOCGRS485)
871 #ifdef TCGETS2
872 COMPATIBLE_IOCTL(TCGETS2)
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Drop the check for "up" being valid on suspend/resume callbacks.
It should be valid always. Get rid of the "pdata" check also as
serial_omap_get_context_loss_count() checks for it.

Tested on omap4 panda and 3630 based Beagle board.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

platform_get_drvdata always retrun a valid value after probe succeed.

It also fixed smatch warnings:
drivers/tty/serial/imx.c:1376 serial_imx_suspend() warn: variable dereferenced before check 'sport' (see line 1372)
drivers/tty/serial/imx.c:1392 serial_imx_resume() warn: variable dereferenced before check 'sport' (see line 1388)
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The autoconfig prints messages while holding the
port's spinlock and that causes a deadlock when
using serial console.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We end up dropping the mutex twice on some errors. We don't want to do
that.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If a serial driver is called post hangup with a second DCD event then we
will attempt to get the ldisc of NULL. Check we have a tty before trying to
do anything with it.

This is still only safe within the uart layer if the caller holds the
relevant uart locks. We could do with a version where the tty is passed for
more general use.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The RS-485 TIOCSRS485 and TIOCGRS485 ioctls are 32-bit compatible, so
in order to call them on 64-bit systems from 32-bit user mode, we add
them to the ioctl pointer list as compatible ioctls.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Kconfig and Makefile changes to add dgrp to the build system.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is based on dgrp-1.9 available from
ftp://ftp1.digi.com/support/beta/linux/dgrp/dgrp-1.9.tgzSigned-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Alan says these are not production ready, and users should be told this,
so put the "(EXPERIMENTAL)" marking back in the Kconfig entry string.
Reported-by: Alan Cox <alan@linux.intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As discussed at the kernel summit this year, CONFIG_EXPERIMENTAL means
nothing, so let's get rid of it.

Cc: Kees Cook <keescook@chromium.org>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Return the value returned by the failing function instead
of -1 (which does not convey the right error information).

Fixes the following smatch warning:
drivers/tty/serial/samsung.c:1687 s3c24xx_serial_modinit() info:
why not propagate 'ret' from uart_register_driver() instead of -1?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the trace we print the wrong values for N(R) on an I frame.
Correct the mask.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Otherwise we start trying to use a bogus channel - ungood.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We don't want to free a random address if the entry is wrong, cover
this and WARN if it ever happens.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HVC returns a size of -1 bytes for the write room in some cases.
This is bogus and not handled by the tty layer at all.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This pulls in the fixes in 3.6-rc6
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull mfd fixes from Samuel Ortiz:
 "This is the remaining MFD fixes for 3.6, with 5 pending fixes:

   - A tps65217 build error fix.
   - A lcp_ich regression fix caused by the MFD driver failing to
     initialize the watchdog sub device due to ACPI conflicts.
   - 2 MAX77693 interrupt handling bug fixes.
   - An MFD core fix, adding an IRQ domain argument to the MFD device
     addition API in order to prevent silent and potentially harmful
     remapping behaviour changes for drivers supporting non-DT
     platforms."

* tag 'mfd-for-linus-3.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: MAX77693: Fix NULL pointer error when initializing irqs
  mfd: MAX77693: Fix interrupt handling bug
  mfd: core: Push irqdomain mapping out into devices
  mfd: lpc_ich: Fix a 3.5 kernel regression for iTCO_wdt driver
  mfd: Move tps65217 regulator plat data handling to regulator

Pull pwm fixes from Thierry Reding:
 "While this comes a bit later than I had wished, both patches are
  rather minor and touch only new drivers so I think these are still
  safe for merging."

* tag 'for-3.6-rc6' of git://gitorious.org/linux-pwm/linux-pwm:
  pwm: pwm-tiehrpwm: Fix conflicting channel period setting
  pwm: pwm-tiecap: Disable APWM mode after configure

Pull scsi target fixes from Nicholas Bellinger:
 "Here is the current set of target-pending fixes headed for v3.6-final

  The main parts of this series include bug-fixes from Paolo Bonzini to
  address an use-after-free bug in pSCSI sense exception handling, along
  with addressing some long-standing bugs wrt the handling of zero-
  length SCSI CDB payloads also specific to pSCSI pass-through device
  backends."

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target: go through normal processing for zero-length REQUEST_SENSE
  target: support zero allocation length in REQUEST SENSE
  target: support zero-size allocation lengths in transport_kmap_data_sg
  target: fail REPORT LUNS with less than 16 bytes of payload
  target: report too-small parameter lists everywhere
  target: go through normal processing for zero-length PSCSI commands
  target: fix use-after-free with PSCSI sense data
  target: simplify code around transport_get_sense_data
  target: move transport_get_sense_data
  target: Check idr_get_new return value in iscsi_login_zero_tsih_s1
  target: Fix ->data_length re-assignment bug with SCSI overflow

Pull power management fixes from Rafael J. Wysocki:
 "Three ACPI device power management fixes related to checking and
  setting device power states."

* tag 'pm-for-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / PM: Use KERN_DEBUG when no power resources are found
  ACPI / PM: Fix resource_lock dead lock in acpi_power_on_device
  ACPI / PM: Infer parent power state from child if unknown, v2

Pull a btrfs revert from Chris Mason:
 "My for-linus branch has one revert in the new quota code.

  We're building up more fixes at etc for the next merge window, but I'm
  keeping them out unless they are bigger regressions or have a huge
  impact."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Revert "Btrfs: fix some error codes in btrfs_qgroup_inherit()"

Pull more sound fixes from Takashi Iwai:
 "Yet more (a bunch of) small fixes that slipped from the previous pull
  request.  Most of commits are pending ASoC fixes, all of which are
  fairly trivial commits."

* tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ASoC: wm8904: correct the index
  ALSA: hda - Yet another position_fix quirk for ASUS machines
  ASoC: tegra: fix maxburst settings in dmaengine code
  ASoC: samsung dma - Don't indicate support for pause/resume.
  ASoC: mc13783: Remove mono support
  ASoC: arizona: Fix typo in 44.1kHz rates
  ASoC: spear: correct the check for NULL dma_buffer pointer
  sound: tegra_alc5632: remove HP detect GPIO inversion
  ASoC: atmel-ssc: include linux/io.h for raw io
  ASoC: dapm: Don't force card bias level to be updated
  ASoC: dapm: Make sure we update the bias level for CODECs with no op
  ASoC: am3517evm: fix error return code
  ASoC: ux500_msp_i2s: better use devm functions and fix error return code
  ASoC: imx-sgtl5000: fix error return code