Instead of relying on RTNL, ets_dump() can use READ_ONCE()
annotations, paired with WRITE_ONCE() ones in ets_change().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of relying on RTNL, codel_dump() can use READ_ONCE()
annotations.

There is no etf_change() yet, this patch imply aligns
this qdisc with others.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of relying on RTNL, codel_dump() can use READ_ONCE()
annotations, paired with WRITE_ONCE() ones in codel_change().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of relying on RTNL, choke_dump() can use READ_ONCE()
annotations, paired with WRITE_ONCE() ones in choke_change().

v2: added a WRITE_ONCE(p->Scell_log, Scell_log)
    per Simon feedback in V1
    Removed the READ_ONCE(q->limit) in choke_enqueue()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of relying on RTNL, cbs_dump() can use READ_ONCE()
annotations, paired with WRITE_ONCE() ones in cbs_change().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of relying on RTNL, cake_dump() can use READ_ONCE()
annotations, paired with WRITE_ONCE() ones in cake_change().

v2: addressed Simon feedback in V1: https://lore.kernel.org/netdev/20240417083549.GA3846178@kernel.org/Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Toke Høiland-Jørgensen <toke@toke.dk>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of relying on RTNL, fq_dump() can use READ_ONCE()
annotations, paired with WRITE_ONCE() in fq_change()

v2: Addressed Simon feedback in V1: https://lore.kernel.org/netdev/20240416181915.GT2320920@kernel.org/Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The qpl_cfg struct was used to make sure that no two different queues
are using QPL with the same qpl_id. We can remove that qpl_cfg struct
since now the qpl_ids map with the queues respectively as follows:
For tx queues: qpl_id = tx_qid
For rx queues: qpl_id = max_tx_queues + rx_qid

And when XDP is used, it will need the user to reduce the tx queues to
be at most half of the max_tx_queues. Then it will use the same number
of tx queues starting from the end of existing tx queues for XDP. So the
XDP queues will not exceed the max_tx_queues range and will not overlap
with the rx queues, where the qpl_ids will not have overlapping too.

Considering of that, we remove the qpl_cfg struct to get the qpl_id
directly based on the queue id. Unless we are erroneously allocating a
rx/tx queue that has already been allocated, we would never allocate
the qpl with the same qpl_id twice. In that case, it should fail much
earlier than the QPL assignment.
Suggested-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Ziwei Xiao <ziweixiao@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Shailend Chand <shailend@google.com>
Link: https://lore.kernel.org/r/20240417205757.778551-1-ziweixiao@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Kory Maincent says:

====================
net: Add support for Power over Ethernet (PoE)

This patch series aims at adding support for PoE (Power over Ethernet),
based on the already existing support for PoDL (Power over Data Line)
implementation. In addition, it adds support for two specific PoE
controller, the Microchip PD692x0 and the TI TPS23881.
====================

Link: https://lore.kernel.org/all/20240417-feature_poe-v9-0-242293fd1900@bootlin.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add a new driver for the TI TPS23881 I2C Power Sourcing Equipment
controller.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240417-feature_poe-v9-14-242293fd1900@bootlin.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add the TPS23881 I2C Power Sourcing Equipment controller device tree
bindings documentation.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240417-feature_poe-v9-13-242293fd1900@bootlin.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add a new driver for the PD692x0 I2C Power Sourcing Equipment controller.
This driver only support i2c communication for now.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240417-feature_poe-v9-12-242293fd1900@bootlin.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add the PD692x0 I2C Power Sourcing Equipment controller device tree
bindings documentation.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240417-feature_poe-v9-11-242293fd1900@bootlin.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Integrate the regulator framework to the PSE framework for enhanced
access to features such as voltage, power measurement, and limits, which
are akin to regulators. Additionally, PSE features like port priorities
could potentially enhance the regulator framework. Note that this
integration introduces some implementation complexity, including wrapper
callbacks, but the potential benefits make it worthwhile.

Regulator are using enable counter with specific behavior.
Two calls to regulator_disable will trigger kernel warnings.
If the counter exceeds one, regulator_disable call won't disable the
PSE PI. These behavior isn't suitable for PSE control.
Added a boolean 'enabled' state to prevent multiple calls to
regulator_enable/disable. These calls will only be called from PSE
framework as it won't have any regulator children, therefore no mutex are
needed to safeguards this boolean.

regulator_get needs the consumer device pointer. Use PSE as regulator
provider and consumer device until we have RJ45 ports represented in
the Kernel.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240417-feature_poe-v9-10-242293fd1900@bootlin.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Implement setup_pi_matrix callback to configure the PSE PI matrix. This
functionality is invoked before registering the PSE and following the core
parsing of the pse_pis devicetree subnode.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240417-feature_poe-v9-9-242293fd1900@bootlin.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

PSE PI setup may encompass multiple PSE controllers or auxiliary circuits
that collectively manage power delivery to one Ethernet port.
Such configurations might support a range of PoE standards and require
the capability to dynamically configure power delivery based on the
operational mode (e.g., PoE2 versus PoE4) or specific requirements of
connected devices. In these instances, a dedicated PSE PI node becomes
essential for accurately documenting the system architecture. This node
would serve to detail the interactions between different PSE controllers,
the support for various PoE modes, and any additional logic required to
coordinate power delivery across the network infrastructure.

The old usage of "#pse-cells" is unsuficient as it carries only the PSE PI
index information.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240417-feature_poe-v9-8-242293fd1900@bootlin.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The Power Sourcing Equipment Power Interface (PSE PI) plays a pivotal role
in the architecture of Power over Ethernet (PoE) systems. It is essentially
a blueprint that outlines how one or multiple power sources are connected
to the eight-pin modular jack, commonly known as the Ethernet RJ45 port.
This connection scheme is crucial for enabling the delivery of power
alongside data over Ethernet cables.

This patch adds support for getting the PSE controller node through PSE PI
device subnode.

This supports adds a way to get the PSE PI id from the pse_pi devicetree
subnode of a PSE controller node simply by reading the reg property.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240417-feature_poe-v9-7-242293fd1900@bootlin.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

As I add support for PoE in PSE networking subsystem it seems legitimate
to be added to the maintainers.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240417-feature_poe-v9-6-242293fd1900@bootlin.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add the PoE pse attributes prefix to be able to use PoE interface.

Example usage:
./ynl/cli.py --spec netlink/specs/ethtool.yaml --no-schema --do pse-get \
             --json '{"header":{"dev-name":"eth0"}}'
{'header': {'dev-index': 4, 'dev-name': 'eth0'},
 'c33-pse-admin-state': 3,
 'c33-pse-pw-d-status': 4}

./ynl/cli.py --spec netlink/specs/ethtool.yaml --no-schema --do pse-set \
             --json '{"header":{"dev-name":"eth0"},
		     "c33-pse-admin-control":3}'
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240417-feature_poe-v9-5-242293fd1900@bootlin.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Remove podl from the attribute prefix to prepare the support of PoE pse
netlink spec.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240417-feature_poe-v9-4-242293fd1900@bootlin.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add PSE PoE interface support in the ethtool pse command.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240417-feature_poe-v9-3-242293fd1900@bootlin.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Introduce an enumeration to define PSE types (C33 or PoDL),
utilizing a bitfield for potential future support of both types.
Include 'pse_get_types' helper for external access to PSE type info.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240417-feature_poe-v9-2-242293fd1900@bootlin.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In the current PSE interface for Ethernet Power Equipment, support is
limited to PoDL. This patch extends the interface to accommodate the
objects specified in IEEE 802.3-2022 145.2 for Power sourcing
Equipment (PSE).

The following objects are now supported and considered mandatory:
- IEEE 802.3-2022 30.9.1.1.5 aPSEPowerDetectionStatus
- IEEE 802.3-2022 30.9.1.1.2 aPSEAdminState
- IEEE 802.3-2022 30.9.1.2.1 aPSEAdminControl

To avoid confusion between "PoDL PSE" and "PoE PSE", which have similar
names but distinct values, we have followed the suggestion of Oleksij
Rempel and Andrew Lunn to maintain separate naming schemes for each,
using c33 (clause 33) prefix for "PoE PSE".
You can find more details in the discussion threads here:
https://lore.kernel.org/netdev/20230912110637.GI780075@pengutronix.de/
https://lore.kernel.org/netdev/2539b109-72ad-470a-9dae-9f53de4f64ec@lunn.ch/Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240417-feature_poe-v9-1-242293fd1900@bootlin.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2024-04-17 (ice)

This series contains updates to ice driver only.

Marcin adds Tx malicious driver detection (MDD) events to be included as
part of mdd-auto-reset-vf.

Dariusz removes unnecessary implementation of ndo_get_phys_port_name.

* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
  ice: Remove ndo_get_phys_port_name
  ice: Add automatic VF reset on Tx MDD events
====================

Link: https://lore.kernel.org/r/20240417165634.2081793-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This driver currently doesn't support any control flags.

Use flow_rule_match_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.

In case any control flags are masked, flow_rule_match_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.

Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Link: https://lore.kernel.org/r/20240417144413.104257-1-ast@fiberby.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This driver currently doesn't support any control flags.

Use flow_rule_match_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.

In case any control flags are masked, flow_rule_match_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.

Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Link: https://lore.kernel.org/r/20240417144407.104241-1-ast@fiberby.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This driver currently doesn't support any control flags.

Use flow_rule_match_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.

In case any control flags are masked, flow_rule_match_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.

Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Link: https://lore.kernel.org/r/20240417144359.104225-1-ast@fiberby.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Change the check for unsupported control flags, to use the new helper
flow_rule_is_supp_control_flags().

Since the helper was based on sfc, then nothing really changes.

Compile-tested, and compiled objects are identical.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20240417140712.100905-1-ast@fiberby.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This driver currently doesn't support any control flags.

Use flow_rule_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.

In case any control flags are masked, flow_rule_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.

Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/20240417135131.99921-1-ast@fiberby.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Test cases need to exit with non-zero status if they failed,
we currently don't do that:

  # KTAP version 1
  # 1..3
  # # At /root/ksft-net-drv/drivers/net/./ping.py line 18:
  # # Check failed 1 != 2
  # not ok 1 ping.test_v4
  # ok 2 ping.test_v6
  # ok 3 ping.test_tcp
  # # Totals: pass:2 fail:1 xfail:0 xpass:0 skip:0 error:0
  ok 1 selftests: drivers/net: ping.py
  ^^^^

It's a bit tempting to make the exit part of ksft_run(),
but that only works well for very trivial setups. We can
revisit this later, if people forget to call ksft_exit().

Link: https://lore.kernel.org/r/20240417231146.2435572-3-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Totals currently only pay attention to exceptions, if check fails
(say ksft_eq()) the test case will be counted as pass:

  # At /ksft/drivers/net/./ping.py line 18:
  # Check failed 1 != 2
  not ok 1 ping.test_v4
  ok 2 ping.test_v6
  ok 3 ping.test_tcp
  # Totals: pass:3 fail:0 xfail:0 xpass:0 skip:0 error:0
            ^^^^^^^^^^^^^

Pay attention to the result.

Fixes: b86761ff ("selftests: net: add scaffolding for Netlink tests in Python")
Link: https://lore.kernel.org/r/20240417231146.2435572-2-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Cross-merge networking fixes after downstream PR.

Conflicts:

include/trace/events/rpcgss.h
  386f4a73 ("trace: events: cleanup deprecated strncpy uses")
  a4833e3a ("SUNRPC: Fix rpcgss_context trace event acceptor field")

Adjacent changes:

drivers/net/ethernet/intel/ice/ice_tc_lib.c
  2cca35f5 ("ice: Fix checking for unsupported keys on non-tunnel device")
  784feaa6 ("ice: Add support for PFCP hardware offload in switchdev")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski:
 "A little calmer than usual, probably just the timing of sub-tree PRs.

  Including fixes from netfilter.

  Current release - regressions:

   - inet: bring NLM_DONE out to a separate recv() again, fix user space
     which assumes multiple recv()s will happen and gets blocked forever

   - drv: mlx5:
       - restore mistakenly dropped parts in register devlink flow
       - use channel mdev reference instead of global mdev instance for
         coalescing
       - acquire RTNL lock before RQs/SQs activation/deactivation

  Previous releases - regressions:

   - net: change maximum number of UDP segments to 128, fix virtio
     compatibility with Windows peers

   - usb: ax88179_178a: avoid writing the mac address before first
     reading

  Previous releases - always broken:

   - sched: fix mirred deadlock on device recursion

   - netfilter:
       - br_netfilter: skip conntrack input hook for promisc packets
       - fixes removal of duplicate elements in the pipapo set backend
       - various fixes for abort paths and error handling

   - af_unix: don't peek OOB data without MSG_OOB

   - drv: flower: fix fragment flags handling in multiple drivers

   - drv: ravb: fix jumbo frames and packet stats accounting

  Misc:

   - kselftest_harness: fix Clang warning about zero-length format

   - tun: limit printing rate when illegal packet received by tun dev"

* tag 'net-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (46 commits)
  net: ethernet: ti: am65-cpsw-nuss: cleanup DMA Channels before using them
  net: usb: ax88179_178a: avoid writing the mac address before first reading
  net: ravb: Fix RX byte accounting for jumbo packets
  net: ravb: Fix GbEth jumbo packet RX checksum handling
  net: ravb: Allow RX loop to move past DMA mapping errors
  net: ravb: Count packets instead of descriptors in R-Car RX path
  net: ethernet: mtk_eth_soc: fix WED + wifi reset
  net:usb:qmi_wwan: support Rolling modules
  selftests: kselftest_harness: fix Clang warning about zero-length format
  net/sched: Fix mirred deadlock on device recursion
  netfilter: nf_tables: fix memleak in map from abort path
  netfilter: nf_tables: restore set elements when delete set fails
  netfilter: nf_tables: missing iterator type in lookup walk
  s390/ism: Properly fix receive message buffer allocation
  net: dsa: mt7530: fix port mirroring for MT7988 SoC switch
  net: dsa: mt7530: fix mirroring frames received on local port
  tun: limit printing rate when illegal packet received by tun dev
  ice: Fix checking for unsupported keys on non-tunnel device
  ice: tc: allow zero flags in parsing tc flower
  ice: tc: check src_vsi in case of traffic from VF
  ...

Pull gpio fixes from Bartosz Golaszewski:

 - use -ENOTSUPP consistently in Intel GPIO drivers

 - don't include dt-bindings headers in gpio-swnode code

 - add missing of device table to gpio-lpc32xx and fix autoloading

* tag 'gpio-fixes-for-v6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  gpiolib: swnode: Remove wrong header inclusion
  gpio: lpc32xx: fix module autoloading
  gpio: crystalcove: Use -ENOTSUPP consistently
  gpio: wcove: Use -ENOTSUPP consistently

The TX and RX DMA Channels used by the driver to exchange data with CPSW
are not guaranteed to be in a clean state during driver initialization.
The Bootloader could have used the same DMA Channels without cleaning them
up in the event of failure. Thus, reset and disable the DMA Channels to
ensure that they are in a clean state before using them.

Fixes: 93a76530 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Reported-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240417095425.2253876-1-s-vadapalli@ti.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

After the commit d2689b6a ("net: usb: ax88179_178a: avoid two
consecutive device resets"), reset operation, in which the default mac
address from the device is read, is not executed from bind operation and
the random address, that is pregenerated just in case, is direclty written
the first time in the device, so the default one from the device is not
even read. This writing is not dangerous because is volatile and the
default mac address is not missed.

In order to avoid this and keep the simplification to have only one
reset and reduce the delays, restore the reset from bind operation and
remove the reset that is commanded from open operation. The behavior is
the same but everything is ready for usbnet_probe.

Tested with ASIX AX88179 USB Gigabit Ethernet devices.
Restore the old behavior for the rest of possible devices because I don't
have the hardware to test.

cc: stable@vger.kernel.org # 6.6+
Fixes: d2689b6a ("net: usb: ax88179_178a: avoid two consecutive device resets")
Reported-by: Jarkko Palviainen <jarkko.palviainen@gmail.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20240417085524.219532-1-jtornosm@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull random number generator fixes from Jason Donenfeld:

 - The input subsystem contributes entropy in some places where a
   spinlock is held, but the entropy accounting code only handled
   callers being in an interrupt or non-atomic process context, but not
   atomic process context. We fix this by removing an optimization and
   just calling queue_work() unconditionally.

 - Greg accidently sent up a patch not intended for his tree and that
   had been nack'd, so that's now reverted.

* tag 'random-6.9-rc5-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
  Revert "vmgenid: emit uevent when VMGENID updates"
  random: handle creditable entropy from atomic process context

Merge tag 'platform-drivers-x86-v6.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86

Pull x86 platform driver fixes from Ilpo Järvinen:

 - amd/pmf: Add SPS notifications quirk (+ quirk support)

 - amd/pmf: Lower Smart PC check message severity

 - x86/ISST: New HW support

 - x86/intel-uncore-freq: Bump minor version to avoid "unsupported" message

 - amd/pmc: New BIOS version still needs Spurious IRQ1 quirk

* tag 'platform-drivers-x86-v6.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
  platform/x86/amd/pmc: Extend Framework 13 quirk to more BIOSes
  platform/x86/intel-uncore-freq: Increase minor number support
  platform/x86: ISST: Add Granite Rapids-D to HPM CPU list
  platform/x86/amd: pmf: Add quirk for ROG Zephyrus G14
  platform/x86/amd: pmf: Add infrastructure for quirking supported funcs
  platform/x86/amd: pmf: Decrease error message to debug

This reverts commit ad6bcdad. I had
nak'd it, and Greg said on the thread that it links that he wasn't going
to take it either, especially since it's not his code or his tree, but
then, seemingly accidentally, it got pushed up some months later, in
what looks like a mistake, with no further discussion in the linked
thread. So revert it, since it's clearly not intended.

Fixes: ad6bcdad ("vmgenid: emit uevent when VMGENID updates")
Cc: stable@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230531095119.11202-2-bchalios@amazon.esSigned-off-by: Jason A. Donenfeld <Jason@zx2c4.com>

The RSS hash report is a feature that's part of the virtio specification.
Currently, virtio backends like qemu, vdpa (mlx5), and potentially vhost
(still a work in progress as per [1]) support this feature. While the
capability to obtain the RSS hash has been enabled in the normal path,
it's currently missing in the XDP path. Therefore, we are introducing
XDP hints through kfuncs to allow XDP programs to access the RSS hash.

1.
https://lore.kernel.org/all/20231015141644.260646-1-akihiko.odaki@daynix.com/#rSigned-off-by: Liang Chen <liangchen.linux@gmail.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20240417071822.27831-1-liangchen.linux@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>