- 13 Nov, 2008 40 commits
-
-
Leslie Watter authored
This patch adds YISO u893 usb modem vendor and product ID to option.c. I had a better experience using this modification and the same system. Signed-off-by:
Leslie Harlley Watter <leslie@watter.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Ajay Kumar Gupta authored
Fixes co-working issue of usb serial device with usb/net devices while oter endpoints are free and can be used.This patch implements the policy that if endpoint resources are available then different BULK request goes to different endpoint otherwise they are multiplexed to one reserved endpoint as currently done. Switch statement case is reordered in musb_giveback() to take care of bulk request both in multiplex scenario and otherwise. NAK limit scheme has to be added for multiplexed BULK request scenario to avoid endpoint starvation due to usb/net devices. Signed-off-by:
Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by:
Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by:
-
Felipe Balbi authored
In order to avoid namespace conflicts, add a prefix to our kernel-wise symbol. Signed-off-by:
-
Ajay Kumar Gupta authored
Fixes compilation warning when musb is configured in gadget mode. Signed-off-by:
-
Felipe Balbi authored
Add an errno to failing case. Signed-off-by:
-
Ajay Kumar Gupta authored
Fixes blurred capture images in dma mode. Isochronous error field in urb and source data buffer pointer were not updated properly in dma mode. Signed-off-by:
-
Alan Stern authored
This patch (as1155) fixes a bug in usbcore. When interfaces are deleted, either because the device was disconnected or because of a configuration change, the extra attribute files and child endpoint devices may get left behind. This is because the core removes them before calling device_del(). But during device_del(), after the driver is unbound the core will reinstall altsetting 0 and recreate those extra attributes and children. The patch prevents this by adding a flag to record when the interface is in the midst of being unregistered. When the flag is set, the attribute files and child devices will not be created. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> [2.6.27, 2.6.26, 2.6.25] Signed-off-by:
-
Paul Ready authored
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11685 When A Nikon D300 camera is connected to a system it is seen in /proc/bus/pci/devices but is not accessible. This is seen in the above file: T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=03 Dev#= 11 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=04b0 ProdID=041a Rev= 1.03 S: Manufacturer=NIKON S: Product=NIKON DSC D300 S: SerialNumber=000008014379 C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=06(still) Sub=01 Prot=01 Driver=usbfs E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl=32ms Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Greg Kroah-Hartman authored
This fixes a reported compiler warning. Reported-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: PCI: ignore bit0 of _OSC return code
-
git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlmLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm: dlm: fix shutdown cleanup
-
git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6: slab: document SLAB_DESTROY_BY_RCU Kconfig: SLUB is the default slab allocator
-
Linus Torvalds authored
* master.kernel.org:/home/rmk/linux-2.6-arm: [ARM] cdb89712: avoid namespace clashes with SRAM_ and BOOTROM_ constants [ARM] cdb89712,clps7500,h720x: avoid namespace clash for FLASH_* constants [ARM] integrator,realview,versatile: remove FLASH_* and EPROM_* constants [ARM] dma-mapping: fix compiler warning [ARM] iop: iop3xx needs registers mapped uncached+unbuffered [ARM] versatile: correct MMC clock rate [ARM] realview: correct MMC clock rate [ARM] 5329/1: Feroceon: fix feroceon_l2_inv_range
-
Helge Deller authored
Commit 2d3854a3 ("cpumask: introduce new API, without changing anything") introduced a build breakage on parisc. This trivial patch fixes it. Signed-off-by:
Helge Deller <deller@gmx.de> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Kyle Mc Martin <kyle@hera.kernel.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
David Teigland authored
Fixes a regression from commit 0f8e0d9a, "dlm: allow multiple lockspace creates". An extraneous 'else' slipped into a code fragment being moved from release_lockspace() to dlm_release_lockspace(). The result of the unwanted 'else' is that dlm threads and structures are not stopped and cleaned up when the final dlm lockspace is removed. Trying to create a new lockspace again afterward will fail with "kmem_cache_create: duplicate cache dlm_conn" because the cache was not previously destroyed. Signed-off-by:
David Teigland <teigland@redhat.com>
-
Peter Zijlstra authored
Explain this SLAB_DESTROY_BY_RCU thing... [hugh@veritas.com: add a pointer to comment in mm/slab.c] Signed-off-by:
Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by:
Jens Axboe <jens.axboe@oracle.com> Acked-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by:
Christoph Lameter <cl@linux-foundation.org> Signed-off-by:
Hugh Dickins <hugh@veritas.com> Signed-off-by:
Pekka Enberg <penberg@cs.helsinki.fi>
-
Simon Arlott authored
In 2007, a0acd820 changed the default slab allocator to SLUB, but the SLAB help text still says SLAB is the default. This change fixes that. Signed-off-by:
Simon Arlott <simon@fire.lp0.eu> Signed-off-by:
-
Russell King authored
Signed-off-by:Russell King <rmk+kernel@arm.linux.org.uk>
-
Russell King authored
Signed-off-by: -
Russell King authored
FLASH_* and EPROM_* constants are unused, and clash with drivers: drivers/atm/ambassador.h:257:1: warning: "FLASH_BASE" redefined drivers/atm/ambassador.h:258:1: warning: "FLASH_SIZE" redefined drivers/atm/iphase.h:332:1: warning: "EPROM_SIZE" redefined so remove them. Signed-off-by: -
Russell King authored
arch/arm/mm/dma-mapping.c: In function `dma_sync_sg_for_cpu': arch/arm/mm/dma-mapping.c:588: warning: statement with no effect Signed-off-by: -
Linus Torvalds authored
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: sched: fix init_idle()'s use of sched_clock() sched: fix stale value in average load per task
-
Rodolfo Giometti authored
Signed-off-by:
Rodolfo Giometti <giometti@linux.it> Cc: Greg KH <greg@kroah.com> Signed-off-by:
-
Rodolfo Giometti authored
C2port implements a two wire serial communication protocol (bit banging) designed to enable in-system programming, debugging, and boundary-scan testing on low pin-count Silicon Labs devices. Currently this code supports only flash programming through sysfs interface but extensions shoud be easy to add. Signed-off-by:
-
Madhusudhan Chikkature authored
Add a brief document about omap2430/3430 HDQ/1-wire driver. Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com> Acked-by:
Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by:
-
Madhusudhan Chikkature authored
Provide the BQ27000 slave interface driver. Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com> Acked-by:
-
Madhusudhan Chikkature authored
The HDQ/1-Wire module of TI OMAP2430/3430 platforms implement the hardware protocol of the master functions of the Benchmark HDQ and the Dallas Semiconductor 1-Wire protocols. These protocols use a single wire for communication between the master (HDQ/1-Wire controller) and the slave (HDQ/1-Wire external compliant device). This patch provides the HDQ driver to suppport TI OMAP2430/3430 platforms. Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com> Acked-by:
-
Madhusudhan Chikkature authored
Export the w1_read_8 function for use of drivers. The OMAP HDQ driver(drivers/w1/masters/omap_hdq.c) uses this function. [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com> Acked-by:
-
Mark Jackson authored
Add support for the Dallas DS1390/93/94 SPI RTC chip. Signed-off-by:
Mark Jackson <mpfj@mimc.co.uk> Acked-by:
Alessandro Zummo <a.zummo@towertech.it> Cc: David Brownell <david-b@pacbell.net> Signed-off-by:
-
Martyn Welch authored
Provide the basic "get" and "set" functionality for the Epson RX-8581 I2C RTC. It currently does not support the RTC's Alarm or Fixed-cycle timer. [akpm@linux-foundation.org: need log2.h for ilog2(), remove unneeded initialisation] Signed-off-by:
Martyn Welch <martyn.welch@gefanuc.com> Signed-off-by:
-
Mark Brown authored
This adds support for the RTC provided by the Wolfson Microelectronics WM8350. This driver was originally written by Graeme Gregory and Liam Girdwood, though it has been modified since then to update it to current mainline coding standards and for API completeness. [akpm@linux-foundation.org: s/schedule_timeout_interruptible/schedule_timeout_uninterruptible/ to prevent bogus timeout when signal_pending()] Signed-off-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: David Brownell <david-b@pacbell.net> Cc: Liam Girdwood <linux@wolfsonmicro.com> Signed-off-by:
-
Darrick J. Wong authored
The ics932s401 is a clock generator chip. This driver allows users to read the current clock outputs. Signed-off-by:
Darrick J. Wong <djwong@us.ibm.com> Signed-off-by:
-
Darrick J. Wong authored
New driver to play with. As Jean mentioned a couple of years ago, this chip is a beast with odd combinations of 8 fans, 4 temperatures, and 13 voltage sensors. This driver has been tested on an IntelliStation Z30. Signed-off-by:
-
Pavel Machek authored
This adds a driver to the accelerometer sensor found in several HP laptops (under the commercial names of "HP Mobile Data Protection System 3D" and "HP 3D driveguard"). It tries to have more or less the same interfaces as the hdaps and other accelerometer drivers: in sysfs and as a joystick. This driver was first written by Yan Burman. Eric Piel has updated it and slimed it up (including the removal of an interface to access to the free-fall feature of the sensor because it is not reliable enough for now). Pavel Machek removed few more features and switched locking from semaphore to mutex. Several people have contributed to the database of the axes. [eric.piel@tremplin-utc.net: LIS3LV02D: Conform to the new ACPI API] Signed-off-by:
Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by:
Yan Burman <burman.yan@gmail.com> Signed-off-by:
Pavel Machek <pavel@suse.cz> Cc: "Mark M. Hoffman" <mhoffman@lightlink.com> Signed-off-by:
-
KAMEZAWA Hiroyuki authored
The start pfn calculation in page_cgroup's memory hotplug notifier chain is wrong. Tested-by:
Badari Pulavarty <pbadari@us.ibm.com> Signed-off-by:
KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by:
-
Theodore Tso authored
Signed-off-by:
"Theodore Ts'o" <tytso@mit.edu> Cc: <linux-ext4@vger.kernel.org> Signed-off-by:
-
Jean-Christophe Lallemand authored
We're working with an AT91SAM9263 Rev B in our design and I experienced some inconsistency in spi-based touchscreen usage between our board and the Atmel evaluation kit we have that runs on a Rev A chip. The data was apparently delayed by 1 byte and got ridiculous data out of the touchscreen driver, very strange. As everything looked normal in the spi, touchscreen and dma logs, I contacted the Atmel support and they triggered me on a new HW bug that appeared in the Rev B SPI controller. The problem is that the SPI controller on the Rev B needs that the software reset is performed two times so that it's performed correctly. Applying the patch below solves the issue on my Rev B board. I've tested it as well on my Rev A evaluation kit and it has apparently no unwanted side effect, things continue to work as expected. Signed-off-by:
Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by:
-
Darrick J. Wong authored
The adt7468 is a follow-on to the adt7463, so plumb in adt7468 support along the same code paths. Signed-off-by:
-
Darrick J. Wong authored
Implement correct range checking for adt7470 to prevent userland from writing impossible values into the chip, and cap out-of-range values per standard hwmon conventions. Implement correct rounding of input values per standard hwmon conventions. Signed-off-by:
-
Darrick J. Wong authored
Implement correct range checking for adt7470 to prevent userland from writing impossible values into the chip, and cap out-of-range values per standard hwmon conventions. Implement correct rounding of input values per standard hwmon conventions. Signed-off-by:
-
