Don't access vqmmc regulator handler, if it's already invalidated.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1594300408-17658-1-git-send-email-vbadigan@codeaurora.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The commit 5a36d6bc ("mmc: core: Add DT-bindings for
MMC_CAP2_FULL_PWR_CYCLE") added the "full-pwr-cycle" property which
is possible to perform a full power cycle of the card at any time.

However, some environment (like r8a77951-salvator-xs) is possible
to perform a full power cycle of the card in suspend via firmware
(PSCI on arm-trusted-firmware). So, in worst case, since we are
not doing a graceful shutdown of the eMMC device (just cut VCCQ
while the eMMC is "sleeping") in suspend, it could lead to internal
data corruptions. So, add MMC_CAP2_FULL_PWR_CYCLE_IN_SUSPEND
to do a graceful shutdown which issues Power Off notification
before entering system suspend.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1594123122-13156-3-git-send-email-yoshihiro.shimoda.uh@renesas.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The commit 5a36d6bc ("mmc: core: Add DT-bindings for
MMC_CAP2_FULL_PWR_CYCLE") added the "full-pwr-cycle" property which
is possible to perform a full power cycle of the card at any time.

However, some environment (like r8a77951-salvator-xs) is possible
to perform a full power cycle of the card in suspend via firmware
(PSCI on arm-trusted-firmware). So, add a new property for such
environment.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1594123122-13156-2-git-send-email-yoshihiro.shimoda.uh@renesas.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Configure SDHC IO pins with low power configuration when the driver
is in suspend state.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1594213888-2780-2-git-send-email-vbadigan@codeaurora.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Since ACPI_PTR() is used to NULLify the value when !CONFIG_ACPI,
'struct sdhci_iproc_acpi_ids' becomes defined but unused.

Fixes the following W=1 kernel build warning:

 mmc/host/sdhci-iproc.c:297:36: warning: ‘sdhci_iproc_acpi_ids’ defined but not used [-Wunused-const-variable=]

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Link: https://lore.kernel.org/r/20200707064701.GC3500@dellSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The variable 'found' is being initialized with a value that is never read
and it is being updated later with a new value.  The initialization is
redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200706163031.503431-1-colin.king@canonical.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

When building the kernel with W=1 the build system complains of:

 drivers/mmc/host/omap.c:854:6: warning: no previous prototype for ‘omap_mmc_notify_cover_event’ [-Wmissing-prototypes]
 854 | void omap_mmc_notify_cover_event(struct device *dev, int num, int is_closed)
 | ^~~~~~~~~~~~~~~~~~~~~~~~~~~

If we move the prototype into a shared headerfile the build system
will be satisfied.  Rather than create a whole new headerfile just
for this purpose, it makes sense to use the already existing
mmc-omap.h.

Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20200701102317.235032-1-lee.jones@linaro.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

cqhci_host_alloc_tdl()'s function header is the only one in
kerneldoc format.  Which seems odd as it's not part of an
external API and isn't referenced anywhere else.  Seeing as
there has also been no attempt to describe the expected
function arguments either, we're going to assume that this is
not actually a bona fide kerneldoc use-case.

Fixes the following W=1 kernel build warning:

 drivers/mmc/host/cqhci.c:163: warning: Function parameter or member 'cq_host' not described in 'cqhci_host_alloc_tdl'

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ritesh Harjani <riteshh@codeaurora.org>
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200701124702.908713-15-lee.jones@linaro.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

__sdhci_msm_set_clock()'s function header is the only one in
kerneldoc format.  Which seems odd as it's not part of an
external API and isn't referenced anywhere else.  Seeing as
there has also been no attempt to describe the expected
function arguments either, we're going to assume that this is
not actually a bona fide kerneldoc use-case.

Fixes the following W=1 kernel build warnings:

 drivers/mmc/host/sdhci-msm.c:1595: warning: Function parameter or member 'host' not described in '__sdhci_msm_set_clock'
 drivers/mmc/host/sdhci-msm.c:1595: warning: Function parameter or member 'clock' not described in '__sdhci_msm_set_clock'

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-14-lee.jones@linaro.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Kerneldoc expects arg descriptions to be in the format '@.*: '.  If either
the '@' or the ':' is omitted then kerneldoc complains that the description
is missing.  Add the missing ':' here and provide a new description for
'value'.

Fixes the following kernel build W=1 warnings:

 drivers/mmc/host/sdhci-of-arasan.c:1394: warning: Function parameter or member 'host' not described in 'sdhci_arasan_update_support64b'
 drivers/mmc/host/sdhci-of-arasan.c:1394: warning: Function parameter or member 'value' not described in 'sdhci_arasan_update_support64b'
 drivers/mmc/host/sdhci-msm.c:1887:6: warning: no previous prototype for ‘sdhci_msm_dump_vendor_regs’ [-Wmissing-prototypes]

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Xiaobo Xie <X.Xie@freescale.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Soeren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-12-lee.jones@linaro.orgAcked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Seeing as sd_wait_data_idle() returns void and only a very specific
read value is checked, there doesn't seem to be a good reason to
check the return value of rtsx_pci_read_register().  So remove
the assignment and definition of 'err'.

Squashes the following W=1 kernel build warning:

 drivers/mmc/host/rtsx_usb_sdmmc.c: In function ‘sd_wait_data_idle’:
 drivers/mmc/host/rtsx_usb_sdmmc.c:657:6: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
 657 | int err, i;
 | ^~~

Cc: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-11-lee.jones@linaro.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Seeing as sd_wait_data_idle() returns void and only a very specific
read value is checked, there doesn't seem to be a good reason to
check the return value of rtsx_pci_read_register().  So remove
the assignment and definition of 'err'.

Squashes the following W=1 kernel build warning:

 drivers/mmc/host/rtsx_pci_sdmmc.c: In function ‘sd_wait_data_idle’:
 drivers/mmc/host/rtsx_pci_sdmmc.c:678:6: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
 678 | int err, i;
 | ^~~

Cc: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-10-lee.jones@linaro.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Provide missing documentation for dw_mci_exynos_suspend_noirq() and
dw_mci_exynos_resume_noirq() function headers.

Fixes the following W=1 kernel build warnings:

 drivers/mmc/host/dw_mmc-exynos.c:184: warning: Function parameter or member 'dev' not described in 'dw_mci_exynos_suspend_noirq'
 drivers/mmc/host/dw_mmc-exynos.c:200: warning: Function parameter or member 'dev' not described in 'dw_mci_exynos_resume_noirq'

Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20200701124702.908713-9-lee.jones@linaro.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Correcting this misspelling squashes the following W=1 build warning(s):

 mmc/core/queue.c:212: warning: Function parameter or member 'mq' not described in '__mmc_init_request'
 mmc/core/queue.c:212: warning: Excess function parameter 'q' description in '__mmc_init_request'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-8-lee.jones@linaro.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

'sg_len' and 'dma_conf' are missing correct kerneldoc documentation and
'buf_phys_addr' was misspelled.  Correcting these issues fixes the
following W=1 kernel build issues:

 mmc/host/atmel-mci.c:352: warning: Function parameter or member 'sg_len' not described in 'atmel_mci'
 mmc/host/atmel-mci.c:352: warning: Function parameter or member 'buf_phys_addr' not described in 'atmel_mci'
 mmc/host/atmel-mci.c:352: warning: Function parameter or member 'dma_conf' not described in 'atmel_mci'

Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-7-lee.jones@linaro.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

No other function in the file is documented using kerneldoc and no
effort to document the function arguments have been made.  It's a
bit of an oddity to say the least.  Let's downgrade it from
kerneldoc to a standard comment block instead.

Fixes the following W=1 kernel build warning:

 drivers/mmc/host/mtk-sd.c:1030: warning: Function parameter or member 'host' not described in 'msdc_recheck_sdio_irq'

Cc: Chaotian Jing <chaotian.jing@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20200701124702.908713-6-lee.jones@linaro.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Describe properties; ext_cd_irq, clk_rates and no_divider (x2).

Squashes the following W=1 kernel build warnings:

 drivers/mmc/host/sdhci-s3c.c:126: warning: Function parameter or member 'ext_cd_irq' not described in 'sdhci_s3c'
 drivers/mmc/host/sdhci-s3c.c:126: warning: Function parameter or member 'clk_rates' not described in 'sdhci_s3c'
 drivers/mmc/host/sdhci-s3c.c:126: warning: Function parameter or member 'no_divider' not described in 'sdhci_s3c'
 drivers/mmc/host/sdhci-s3c.c:139: warning: Function parameter or member 'no_divider' not described in 'sdhci_s3c_drv_data'

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20200701124702.908713-5-lee.jones@linaro.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Remainder of the kerneldoc descriptions look present and correct.

Fixes the following W=1 kernel build warnings:

 drivers/mmc/core/regulator.c:178: warning: Function parameter or member 'mmc' not described in 'mmc_regulator_set_vqmmc'
 drivers/mmc/core/regulator.c:178: warning: Function parameter or member 'ios' not described in 'mmc_regulator_set_vqmmc'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-4-lee.jones@linaro.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add missing kerneldoc entry for sdio_set_host_pm_flags()'s 'flag'
function argument.

Fixes the following W=1 kernel build warning:

 kernel/drivers/mmc/core/sdio_io.c:722: warning: Function parameter or member 'flags' not described in 'sdio_set_host_pm_flags'

Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-3-lee.jones@linaro.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Not all source files which include quirks.h make use of the all of
the available fixup information.  When this happens the compiler
complains that some constant variables are defined by never used.
We can fix this by telling the compiler that this intentional by
simply marking them as __maybe_unused.

Fixes the following W=1 kernel build warnings:

 In file included from drivers/mmc/core/sdio.c:22:
 drivers/mmc/core/quirks.h:105:31: warning: ‘mmc_ext_csd_fixups’ defined but not used [-Wunused-const-variable=]
 105 | static const struct mmc_fixup mmc_ext_csd_fixups[] = {
 | ^~~~~~~~~~~~~~~~~~
 drivers/mmc/core/quirks.h:17:31: warning: ‘mmc_blk_fixups’ defined but not used [-Wunused-const-variable=]
 17 | static const struct mmc_fixup mmc_blk_fixups[] = {
 | ^~~~~~~~~~~~~~
 In file included from drivers/mmc/core/mmc.c:25:
 drivers/mmc/core/quirks.h:123:31: warning: ‘sdio_fixup_methods’ defined but not used [-Wunused-const-variable=]
 123 | static const struct mmc_fixup sdio_fixup_methods[] = {
 | ^~~~~~~~~~~~~~~~~~
 drivers/mmc/core/quirks.h:17:31: warning: ‘mmc_blk_fixups’ defined but not used [-Wunused-const-variable=]
 17 | static const struct mmc_fixup mmc_blk_fixups[] = {
 | ^~~~~~~~~~~~~~

Cc: Andrei Warkentin <andreiw@motorola.com>
Cc: Martin Mares <mj@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-2-lee.jones@linaro.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Fix sparse build warning:

drivers/mmc/host/sdhci-msm.c:1888:6: warning:
 symbol 'sdhci_msm_dump_vendor_regs' was not declared. Should it be static?
Signed-off-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200702020347.77214-1-weiyongjun1@huawei.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If this controller doesn't issue interrupt for response of command,
this driver lacks to call dma_unmap_sg(). So, fix the issue by
using end() of struct tmio_mmc_dma_ops.
Reported-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Fixes: 2a68ea78 ("mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1590044466-28372-4-git-send-email-yoshihiro.shimoda.uh@renesas.comTested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

To add end() operation in the future, clean the code of
renesas_sdhi_internal_dmac_complete_tasklet_fn(). No behavior change.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1590044466-28372-3-git-send-email-yoshihiro.shimoda.uh@renesas.comTested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Related drivers like renesas_sdhi_internal_dmac are possible
to lack dma unmaping in error cases (for example response timeout).

Since tmio_mmc_finish_request() will be always called in any case,
to fix the issue, add end operation into struct tmio_mmc_dma_ops and
call the operation in tmio_mmc_finish_request() to call dma_ummap API
by the related drivers correctly.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1590044466-28372-2-git-send-email-yoshihiro.shimoda.uh@renesas.comTested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Define appropriate macro names for consistency with other macros.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200629072144.24351-1-pali@kernel.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

On qcom SD host controllers voltage switching be done after the HW
is ready for it. The HW informs its readiness through power irq.
The voltage switching should happen only then.

Use the internal voltage switching and then control the voltage
switching using power irq.

IO-bus supply of eMMC would be kept always-on. So set the load
for this supply to configure it in LPM when eMMC is suspend state
and in HPM when eMMC is active.
Co-developed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Co-developed-by: Vijay Viswanath <vviswana@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Co-developed-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1592919288-1020-4-git-send-email-vbadigan@codeaurora.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Set the default power mode, MMC_POWER_UNDEFINED, in mmc_alloc_host() rather
than in mmc_start_host(). This enables host drivers to make use of the
initial state during ->probe().

Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Link:
https://lore.kernel.org/r/1592919288-1020-3-git-send-email-vbadigan@codeaurora.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If vendor platform drivers are controlling whole logic of voltage
switching, then sdhci driver no need control vqmmc regulator.
So skip enabling/disable vqmmc from SDHC driver.
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1592919288-1020-2-git-send-email-vbadigan@codeaurora.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

HS400/HS200/eMMC HS doesn't have Preset Value register.
Hence, sdhci_set_ios function overrides the value set by fmw to
SDHCI_CTRL_DRV_TYPE_B.
This patch sets drv_type to MMC_SET_DRIVER_TYPE_A
so that host_control2 register gets updated with the required
strength value.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200623133347.4598-1-akshu.agrawal@amd.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

USDHC of i.MX has internal IC debug register, which record the IC
logical status. So dump these logical status in error condition,
this can help analyzing issue.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1592985830-13038-1-git-send-email-haibo.chen@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In current code logic, when work in SDR12/SDR25 mode, the final clock
rate is incorrect, just the legancy 400KHz, because the
card->sw_caps.sd3_bus_mode do not has the flag SD_MODE_UHS_SDR12 or
SD_MODE_UHS_SDR25. Besides, SDIO_SPEED_SDR12 is actually value 0, and
every mode need to config the timing and clock rate, so remove the
‘if’ operator.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Tested-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/1592813959-5914-1-git-send-email-haibo.chen@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add support for writing new clkbuf_sel property for the J721e 4 bit IP.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-7-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

For speed modes where DLL is not enabled write to TXDLYCLK to enable
transmitter delay chain mode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-6-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The clock > CLOCK_TOO_SLOW_HZ condition gating phy configuration
is only required because dll should not be enabled at too low a
clock frequency or too low timing. Make sure that this condition
only gates dll enablement.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-5-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add Support for AM65x PG2.0. Use the SoC bus framework to fixup
the driver data and skip do DLL calibration if the revision is 1.0
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-4-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Not all controllers need calibration for the PHY DLL. Add a DLL_CALIB flag
to indicate the same.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-3-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add documentation for the clock buffer select phy property in the
am654x and j721e 4 bit IP
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-2-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Convert the pwrseq binding to DT schema format using json-schema.

At the same time, fix a couple of issues with the examples discovered by
the validation tool -- missing ";"
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200622164431.3dbc8c5a@xhacker.debianSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

"K" stands for "kelvin".

While at it, make the spacing before units consistent.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200618080321.16678-1-geert+renesas@glider.beReviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>