Skip relevant HW configurations once FW security is enabled
because these configurations are being performed by FW.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Add support for fetching security indication from FW.
This indication is needed in order to skip unnecessary
initializations done by FW.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Fix cs counters structure in uapi to be one flat structure instead
of two instances of the same other structure.
use atomic read/increment for context counters so we could use
one structure for both aggregated and context counters.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Today driver is able to load a whole FW binary into a specific
location on ASIC. We add support for loading sections from the
same FW binary into different loactions.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

GCC 7.3.1 20180303 (Red Hat 7.3.1-5) complains that collective_engine_id
might be used uninitialized.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Remove unreachable code in gaudi collective flow.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Although we get a valid cs type from the callee, in case new values
will be added in the future, it is best to check the expected values
in that function.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

In GAUDI we don't have an MMU towards the HBM device memory. Therefore,
the user access that memory directly through physical address (via the
different engines) without the need to go through the driver to
allocate/free memory on the HBM.

For system monitoring purposes, the driver will keep track of the HBM
usage. This can be done as long as the user accurately reports the
allocations and releases of HBM memory, through the existing MEMORY
IOCTL uapi.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Implement sync stream collective for GAUDI. Need to allocate additional
resources for that and add ctx_fini() to clean up those resources.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

DMA5 QMAN is designated to be used for reduction process, hence it will
be no longer configured as external queue.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Define new API for collective wait support and modify sync stream
common flow. In addition add kernel CB allocation support for
internal queues.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

In the future there will be situations where queues can accept either
kernel allocated CBs or user allocated CBs, depending on different
states.

Therefore, instead of using a boolean variable of kernel/user allocated
CB, we need to use a bitmask to indicate that, which will allow to
combine the two options.

Add a flag to the uapi so the user will be able to indicate whether
the CB was allocated by kernel or by user. Of course the driver
validates that.
Signed-off-by: Tal Cohen <talcohen@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Initialize the QMANs that are responsible to submit doorbells to the NIC
engines. Add support for stopping and disabling them, and reset them as
part of the hard-reset procedure of GAUDI. This will allow the user to
submit work to the NICs.

Add support for receiving events on QMAN errors from the firmware.

However, the nic_ports_mask is still initialized to 0. That means this code
won't initialize the QMANs just yet. That will be in a later patch.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Configure the security properties of the NIC IP. This is to prevent the
user process from doing something with the NIC that he shouldn't do. e.g.
crash the server, steal data, etc.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Add new structures and messages that the driver use to interact with the
firmware to receive information and events (errors) about GAUDI's NIC.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Add auto-generated header files that describe the NIC QMANs registers
used by the driver.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

We already check if queue index is smaller than max queues a few lines
above this check so no need to check this again.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Refactor sync stream implementation by reducing function length
for better readability.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Support advanced monitor functionality to monitor more than a
single SOB. In addition expand all CB generation functions
with buffer offset in order to put in them multiple packets that are
generated by different functions.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Refactor sync stream implementation by adding more structures for
better readability. In addition reducing allocated resources.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

In case we are running without MMU enabled (debug mode), no need to
initialize the VM module in the driver.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

No need to print when the driver starts to initialize the H/W. Drivers
should be silent when everything is OK.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

The driver now loads the firmware in two stages. For debugging purposes
we need to support situations where only the first stage firmware is
loaded.

Therefore, use a bitmask to determine which F/W is loaded
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

F/W can be loaded but device CPU queues disabled. In that case, HWMON
should be disabled. This is only relevant when debugging
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Currently mmu_prepare is located at context switch.
Since we support a single context, no reason to reconfigure
the MMU registers every context switch.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

In case we will have multiple contexts/processes, we can't just
increment aggregated counters. We need to make them atomic as they can
be incremented by multiple processes
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Update the email to my kernel.org email address and update the git
repository address to the git.kernel.org
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We need the fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull locking fixes from Thomas Gleixner:
 "Two more places which invoke tracing from RCU disabled regions in the
  idle path.

  Similar to the entry path the low level idle functions have to be
  non-instrumentable"

* tag 'locking-urgent-2020-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  intel_idle: Fix intel_idle() vs tracing
  sched/idle: Fix arch_cpu_idle() vs tracing

Pull irq fixes from Thomas Gleixner:
 "Two fixes for irqchip drivers:

   - Save and restore the GICV3 ITS state unconditionally on
     suspend/resume to handle firmware which fails to do so.

   - Use the correct index into the fwspec parameters to read the irq
     trigger type in the EXIU chip driver"

* tag 'irq-urgent-2020-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gic-v3-its: Unconditionally save/restore the ITS state on suspend
  irqchip/exiu: Fix the index of fwspec for IRQ type

Pull EFI fixes from Borislav Petkov:
 "More EFI fixes forwarded from Ard Biesheuvel:

   - revert efivarfs kmemleak fix again - it was a false positive

   - make CONFIG_EFI_EARLYCON depend on CONFIG_EFI explicitly so it does
     not pull in other dependencies unnecessarily if CONFIG_EFI is not
     set

   - defer attempts to load SSDT overrides from EFI vars until after the
     efivar layer is up"

* tag 'efi-urgent-for-v5.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi: EFI_EARLYCON should depend on EFI
  efivarfs: revert "fix memory leak in efivarfs_create()"
  efi/efivars: Set generic ops before loading SSDT

Pull x86 fixes from Borislav Petkov:
 "A couple of urgent fixes which accumulated this last week:

   - Two resctrl fixes to prevent refcount leaks when manipulating the
     resctrl fs (Xiaochen Shen)

   - Correct prctl(PR_GET_SPECULATION_CTRL) reporting (Anand K Mistry)

   - A fix to not lose already seen MCE severity which determines
     whether the machine can recover (Gabriele Paoloni)"

* tag 'x86_urgent_for_v5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mce: Do not overwrite no_way_out if mce_end() fails
  x86/speculation: Fix prctl() when spectre_v2_user={seccomp,prctl},ibpb
  x86/resctrl: Add necessary kernfs_put() calls to prevent refcount leak
  x86/resctrl: Remove superfluous kernfs_get() calls to prevent refcount leak

Pull RISC-V fixes from Palmer Dabbelt:
 "I've collected a handful of fixes over the past few weeks:

   - A fix to un-break the build-id argument to the vDSO build, which is
     necessary for the LLVM linker.

   - A fix to initialize the jump label subsystem, without which it (and
     all the stuff that uses it) doesn't actually function.

   - A fix to include <asm/barrier.h> from <vdso/processor.h>, without
     which some drivers won't compile"

* tag 'riscv-for-linus-5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  RISC-V: fix barrier() use in <vdso/processor.h>
  RISC-V: Add missing jump label initialization
  riscv: Explicitly specify the build id style in vDSO Makefile again

Merge tag 'kbuild-fixes-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Remove unused OBJSIZE variable.

 - Fix rootless deb-pkg build in a setgid directory.

* tag 'kbuild-fixes-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  builddeb: Fix rootless build in setuid/setgid directory
  kbuild: remove unused OBJSIZE

Merge tag 'perf-tools-fixes-for-v5.10-2020-11-28' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux

Pull perf tool fixes from Arnaldo Carvalho de Melo:

 - Fix die_entrypc() when DW_AT_ranges DWARF attribute not available

 - Cope with broken DWARF (missing DW_AT_declaration) generated by some
   recent gcc versions

 - Do not generate CGROUP metadata events when not asked to in 'perf
   record'

 - Use proper CPU for shadow stats in 'perf stat'

 - Update copy of libbpf's hashmap.c, silencing tools/perf build warning

 - Fix return value in 'perf diff'

* tag 'perf-tools-fixes-for-v5.10-2020-11-28' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  perf probe: Change function definition check due to broken DWARF
  perf probe: Fix to die_entrypc() returns error correctly
  perf stat: Use proper cpu for shadow stats
  perf record: Synthesize cgroup events only if needed
  perf diff: Fix error return value in __cmd_diff()
  perf tools: Update copy of libbpf's hashmap.c

Pull USB / PHY driver fixes from Greg KH:
 "Here are a few small USB and PHY driver fixes for 5.10-rc6. They
  include:

   - small PHY driver fixes to resolve reported issues

   - USB quirks added for "broken" devices

   - typec fixes for reported problems

   - USB gadget fixes for small issues

  Full details are in the shortlog, nothing major in here and all have
  been in linux-next with no reported issues"

* tag 'usb-5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: typec: stusb160x: fix power-opmode property with typec-power-opmode
  USB: core: Change %pK for __user pointers to %px
  USB: core: Fix regression in Hercules audio card
  usb: gadget: Fix memleak in gadgetfs_fill_super
  usb: gadget: f_midi: Fix memleak in f_midi_alloc
  USB: quirks: Add USB_QUIRK_DISCONNECT_SUSPEND quirk for Lenovo A630Z TIO built-in usb-audio card
  usb: typec: qcom-pmic-typec: fix builtin build errors
  phy: mediatek: fix spelling mistake in Kconfig "veriosn" -> "version"
  phy: qualcomm: Fix 28 nm Hi-Speed USB PHY OF dependency
  phy: qualcomm: usb: Fix SuperSpeed PHY OF dependency
  phy: intel: PHY_INTEL_KEEMBAY_EMMC should depend on ARCH_KEEMBAY
  usb: cdns3: gadget: calculate TD_SIZE based on TD
  usb: cdns3: gadget: initialize link_trb as NULL
  phy: cpcap-usb: Use IRQF_ONESHOT
  phy: qcom-qmp: Initialize another pointer to NULL
  phy: tegra: xusb: Fix dangling pointer on probe failure
  phy: usb: Fix incorrect clearing of tca_drv_sel bit in SETUP reg for 7211

Pull char/misc driver fixes from Greg KH:
 "Here are some small misc driver fixes for 5.10-rc6.  They include:

   - interconnect fixes for reported problems

   - habanalabs bugfix for found issue when doing the switch fallthrough
     patches

   - MAINTAINERS file update for coresight reviewers/maintainers

  All have been in linux-next with no reported issues"

* tag 'char-misc-5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  MAINTAINERS: Adding help for coresight subsystem
  habanalabs/gaudi: fix missing code in ECC handling
  interconnect: fix memory trashing in of_count_icc_providers()
  interconnect: qcom: qcs404: Remove GPU and display RPM IDs
  interconnect: qcom: msm8916: Remove rpm-ids from non-RPM nodes
  interconnect: qcom: msm8974: Don't boost the NoC rate during boot
  interconnect: qcom: msm8974: Prevent integer overflow in rate

Merge tag 'asm-generic-fixes-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic

Pull asm-generic fix from Arnd Bergmann:
 "Add correct MAX_POSSIBLE_PHYSMEM_BITS setting to asm-generic.

  This is a single bugfix for a bug that Stefan Agner found on 32-bit
  Arm, but that exists on several other architectures"

* tag 'asm-generic-fixes-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
  arch: pgtable: define MAX_POSSIBLE_PHYSMEM_BITS where needed

Pull ARM SoC fixes from Arnd Bergmann:
 "Another set of patches for devicetree files and Arm SoC specific
  drivers:

   - A fix for OP-TEE shared memory on non-SMP systems

   - multiple code fixes for the OMAP platform, including one regression
     for the CPSW network driver and a few runtime warning fixes

   - Some DT patches for the Rockchip RK3399 platform, in particular
     fixing the MMC device ordering that recently became
     nondeterministic with async probe.

   - Multiple DT fixes for the Tegra platform, including a regression
     fix for suspend/resume on TX2

   - A regression fix for a user-triggered fault in the NXP dpio driver

   - A regression fix for a bug caused by an earlier bug fix in the
     xilinx firmware driver

   - Two more DTC warning fixes

   - Sylvain Lemieux steps down as maintainer for the NXP LPC32xx
     platform"

* tag 'arm-soc-fixes-v5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
  arm64: tegra: Fix Tegra234 VDK node names
  arm64: tegra: Wrong AON HSP reg property size
  arm64: tegra: Fix USB_VBUS_EN0 regulator on Jetson TX1
  arm64: tegra: Correct the UART for Jetson Xavier NX
  arm64: tegra: Disable the ACONNECT for Jetson TX2
  optee: add writeback to valid memory type
  firmware: xilinx: Use hash-table for api feature check
  firmware: xilinx: Fix SD DLL node reset issue
  soc: fsl: dpio: Get the cpumask through cpumask_of(cpu)
  ARM: dts: dra76x: m_can: fix order of clocks
  bus: ti-sysc: suppress err msg for timers used as clockevent/source
  MAINTAINERS: Remove myself as LPC32xx maintainers
  arm64: dts: qcom: clear the warnings caused by empty dma-ranges
  arm64: dts: broadcom: clear the warnings caused by empty dma-ranges
  ARM: dts: am437x-l4: fix compatible for cpsw switch dt node
  arm64: dts: rockchip: Reorder LED triggers from mmc devices on rk3399-roc-pc.
  arm64: dts: rockchip: Assign a fixed index to mmc devices on rk3399 boards.
  arm64: dts: rockchip: Remove system-power-controller from pmic on Odroid Go Advance
  arm64: dts: rockchip: fix NanoPi R2S GMAC clock name
  ARM: OMAP2+: Manage MPU state properly for omap_enter_idle_coupled()
  ...