Pull io_uring fix from Jens Axboe:
 "Revert of a patch from this release that caused a regression"

* tag 'io_uring-5.11-2021-02-12' of git://git.kernel.dk/linux-block:
  Revert "io_uring: don't take fs for recvmsg/sendmsg"

Pull drm fixes from Dave Airlie:
 "Regular fixes for final, there is a ttm regression fix, dp-mst fix,
  one amdgpu revert, two i915 fixes, and some misc fixes for sun4i,
  xlnx, and vc4.

  All pretty quiet and don't think we have any known outstanding
  regressions.

  ttm:
   - page pool regression fix.

  dp_mst:
   - don't report un-attached ports as connected

  amdgpu:
   - blank screen fix

  i915:
   - ensure Type-C FIA is powered when initializing
   - fix overlay frontbuffer tracking

  sun4i:
   - tcon1 sync polarity fix
   - always set HDMI clock rate
   - fix H6 HDMI PHY config
   - fix H6 max frequency

  vc4:
   - fix buffer overflow

  xlnx:
   - fix memory leak"

* tag 'drm-fixes-2021-02-12' of git://anongit.freedesktop.org/drm/drm:
  drm/ttm: make sure pool pages are cleared
  drm/sun4i: dw-hdmi: Fix max. frequency for H6
  drm/sun4i: Fix H6 HDMI PHY configuration
  drm/sun4i: dw-hdmi: always set clock rate
  drm/sun4i: tcon: set sync polarity for tcon1 channel
  drm/i915: Fix overlay frontbuffer tracking
  Revert "drm/amd/display: Update NV1x SR latency values"
  drm/i915/tgl+: Make sure TypeC FIA is powered up when initializing it
  drm/dp_mst: Don't report ports connected if nothing is attached to them
  drm/xlnx: fix kmemleak by sending vblank_event in atomic_disable
  drm/vc4: hvs: Fix buffer overflow with the dlist handling

Pull tracing fix from Steven Rostedt:
 "Fix buffer overflow in trace event filter.

  It was reported that if an trace event was larger than a page and was
  filtered, that it caused memory corruption. The reason is that
  filtered events first go into a buffer to test the filter before being
  written into the ring buffer. Unfortunately, this write did not check
  the size"

* tag 'trace-v5.11-rc7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Check length before giving out the filter buffer

Pull xen fix from Juergen Gross:
 "A single fix for an issue introduced this development cycle: when
  running as a Xen guest on Arm systems the kernel will hang during
  boot"

* tag 'for-linus-5.11-rc8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  arm/xen: Don't probe xenbus as part of an early initcall

Pull RISC-V fix from Palmer Dabbelt:
 "A single fix this week: the removal of the GPIO reset method for the
  Ethernet phy on the HiFive Unleashed.

  This returns to relying on the bootloader's phy reset sequence, which
  we'll have to continue doing until we can sort out how to get the
  Linux phy driver to perform the special reset dance required for this
  phy"

* tag 'riscv-for-linus-5.11-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  Revert "dts: phy: add GPIO number and active state used for phy reset"

Pull arm64 fix from Catalin Marinas:
 "Fix PTRACE_PEEKMTETAGS access to an mmapped region before the first
  write"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: mte: Allow PTRACE_PEEKMTETAGS access to the zero page

The ptrace(PTRACE_PEEKMTETAGS) implementation checks whether the user
page has valid tags (mapped with PROT_MTE) by testing the PG_mte_tagged
page flag. If this bit is cleared, ptrace(PTRACE_PEEKMTETAGS) returns
-EIO.

A newly created (PROT_MTE) mapping points to the zero page which had its
tags zeroed during cpu_enable_mte(). If there were no prior writes to
this mapping, ptrace(PTRACE_PEEKMTETAGS) fails with -EIO since the zero
page does not have the PG_mte_tagged flag set.

Set PG_mte_tagged on the zero page when its tags are cleared during
boot. In addition, to avoid ptrace(PTRACE_PEEKMTETAGS) succeeding on
!PROT_MTE mappings pointing to the zero page, change the
__access_remote_tags() check to (vm_flags & VM_MTE) instead of
PG_mte_tagged.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fixes: 34bfeea4 ("arm64: mte: Clear the tags when a page is mapped in user-space with PROT_MTE")
Cc: <stable@vger.kernel.org> # 5.10.x
Cc: Will Deacon <will@kernel.org>
Reported-by: Luis Machado <luis.machado@linaro.org>
Tested-by: Luis Machado <luis.machado@linaro.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lore.kernel.org/r/20210210180316.23654-1-catalin.marinas@arm.com

(I've pulled from a non-tag to get the ttm regression fix)
drm-misc-fixes-2021-02-10:
 * dp_mst: Don't report un-attached ports as connected
 * sun4i: tcon1 sync polarity fix; Always set HDMI clock rate; Fix
          H6 HDMI PHY config; Fix H6 max frequency
 * vc4: Fix buffer overflow
 * xlnx: Fix memory leak
 * ttm: page pool regression fix.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/YCPo6g3gDxD3P//h@linux-uq9g

Merge tag 'drm-intel-fixes-2021-02-11' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

drm/i915 fixes for v5.11 final:
- Ensure Type-C FIA is powered when initializing
- Fix overlay frontbuffer tracking
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87r1lnc78t.fsf@intel.com

Merge tag 'amd-drm-fixes-5.11-2021-02-10' of https://gitlab.freedesktop.org/agd5f/linux into drm-fixes

amd-drm-fixes-5.11-2021-02-10:

amdgpu:
- Blank screen fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210210223508.4428-1-alexander.deucher@amd.com

Pull powerpc fix from Michael Ellerman:
 "One fix for a regression seen in io_uring, introduced by our support
  for KUAP (Kernel User Access Prevention) with the Hash MMU.

  Thanks to Aneesh Kumar K.V, and Zorro Lang"

* tag 'powerpc-5.11-8' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/kuap: Allow kernel thread to access userspace after kthread_use_mm

When filters are used by trace events, a page is allocated on each CPU and
used to copy the trace event fields to this page before writing to the ring
buffer. The reason to use the filter and not write directly into the ring
buffer is because a filter may discard the event and there's more overhead
on discarding from the ring buffer than the extra copy.

The problem here is that there is no check against the size being allocated
when using this page. If an event asks for more than a page size while being
filtered, it will get only a page, leading to the caller writing more that
what was allocated.

Check the length of the request, and if it is more than PAGE_SIZE minus the
header default back to allocating from the ring buffer directly. The ring
buffer may reject the event if its too big anyway, but it wont overflow.

Link: https://lore.kernel.org/ath10k/1612839593-2308-1-git-send-email-wgong@codeaurora.org/

Cc: stable@vger.kernel.org
Fixes: 0fc1b09f ("tracing: Use temp buffer when filtering events")
Reported-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

Pull gpio fixes from Bartosz Golaszewski:
 "This is hopefully the last batch of fixes for this release cycle. We
  have a minor fix for a Kconfig regression as well as fixes for older
  bugs in gpio-ep93xx:

   - don't build gpio-mxs unconditionally with COMPILE_TEST enabled

   - fix two problems with interrupt handling in gpio-ep93xx"

* tag 'gpio-fixes-for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  gpio: ep93xx: Fix single irqchip with multi gpiochips
  gpio: ep93xx: fix BUG_ON port F usage
  gpio: mxs: GPIO_MXS should not default to y unconditionally

The old implementation wasn't consistend on this.

But it looks like we depend on this so better bring it back.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reported-and-tested-by: Mike Galbraith <efault@gmx.de>
Fixes: d099fc8f ("drm/ttm: new TT backend allocation pool v3")
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210210160549.1462-1-christian.koenig@amd.com

After Commit 3499ba81 ("xen: Fix event channel callback via
INTX/GSI"), xenbus_probe() will be called too early on Arm. This will
recent to a guest hang during boot.

If the hang wasn't there, we would have ended up to call
xenbus_probe() twice (the second time is in xenbus_probe_initcall()).

We don't need to initialize xenbus_probe() early for Arm guest.
Therefore, the call in xen_guest_init() is now removed.

After this change, there is no more external caller for xenbus_probe().
So the function is turned to a static one. Interestingly there were two
prototypes for it.

Cc: stable@vger.kernel.org
Fixes: 3499ba81 ("xen: Fix event channel callback via INTX/GSI")
Reported-by: Ian Jackson <iwj@xenproject.org>
Signed-off-by: Julien Grall <jgrall@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/20210210170654.5377-1-julien@xen.orgSigned-off-by: Juergen Gross <jgross@suse.com>

VSC8541 phys need a special reset sequence, which the driver doesn't
currentlny support.  As a result enabling the reset via GPIO essentially
guarnteees that the device won't work correctly.  We've been relying on
bootloaders to reset the device for years, with this revert we'll go
back to doing so until we can sort out how to get the reset sequence
into the kernel.

This reverts commit a0fa9d72.

Fixes: a0fa9d72 ("dts: phy: add GPIO number and active state used for phy reset")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>

Pull power management fixes from Rafael Wysocki:
 "Address a performance regression related to scale-invariance on x86
  that may prevent turbo CPU frequencies from being used in certain
  workloads on systems using acpi-cpufreq as the CPU performance scaling
  driver and schedutil as the scaling governor"

* tag 'pm-5.11-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: ACPI: Update arch scale-invariance max perf ratio if CPPC is not there
  cpufreq: ACPI: Extend frequency tables to cover boost frequencies

Pull ACPI fix from Rafael Wysocki:
 "Revert a problematic ACPICA commit that changed the code to attempt to
  update memory regions which may be read-only on some systems (Ard
  Biesheuvel)"

* tag 'acpi-5.11-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Revert "ACPICA: Interpreter: fix memory leak by using existing buffer"

Pull dmaengine fixes from Vinod Koul:
 "Some late fixes for dmaengine:

  Core:
   - fix channel device_node deletion

  Driver fixes:
   - dw: revert of runtime pm enabling
   - idxd: device state fix, interrupt completion and list corruption
   - ti: resource leak

* tag 'dmaengine-fix2-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
  dmaengine dw: Revert "dmaengine: dw: Enable runtime PM"
  dmaengine: idxd: check device state before issue command
  dmaengine: ti: k3-udma: Fix a resource leak in an error handling path
  dmaengine: move channel device_node deletion to driver
  dmaengine: idxd: fix misc interrupt completion
  dmaengine: idxd: Fix list corruption in description completion

This reverts commit 10cad2c4.

Petr reports that with this commit in place, io_uring fails the chroot
test (CVE-202-29373). We do need to retain ->fs for send/recvmsg, so
revert this commit.
Reported-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull networking fixes from David Miller:
 "Another pile of networing fixes:

   1) ath9k build error fix from Arnd Bergmann

   2) dma memory leak fix in mediatec driver from Lorenzo Bianconi.

   3) bpf int3 kprobe fix from Alexei Starovoitov.

   4) bpf stackmap integer overflow fix from Bui Quang Minh.

   5) Add usb device ids for Cinterion MV31 to qmi_qwwan driver, from
      Christoph Schemmel.

   6) Don't update deleted entry in xt_recent netfilter module, from
      Jazsef Kadlecsik.

   7) Use after free in nftables, fix from Pablo Neira Ayuso.

   8) Header checksum fix in flowtable from Sven Auhagen.

   9) Validate user controlled length in qrtr code, from Sabyrzhan
      Tasbolatov.

  10) Fix race in xen/netback, from Juergen Gross,

  11) New device ID in cxgb4, from Raju Rangoju.

  12) Fix ring locking in rxrpc release call, from David Howells.

  13) Don't return LAPB error codes from x25_open(), from Xie He.

  14) Missing error returns in gsi_channel_setup() from Alex Elder.

  15) Get skb_copy_and_csum_datagram working properly with odd segment
      sizes, from Willem de Bruijn.

  16) Missing RFS/RSS table init in enetc driver, from Vladimir Oltean.

  17) Do teardown on probe failure in DSA, from Vladimir Oltean.

  18) Fix compilation failures of txtimestamp selftest, from Vadim
      Fedorenko.

  19) Limit rx per-napi gro queue size to fix latency regression, from
      Eric Dumazet.

  20) dpaa_eth xdp fixes from Camelia Groza.

  21) Missing txq mode update when switching CBS off, in stmmac driver,
      from Mohammad Athari Bin Ismail.

  22) Failover pending logic fix in ibmvnic driver, from Sukadev
      Bhattiprolu.

  23) Null deref fix in vmw_vsock, from Norbert Slusarek.

  24) Missing verdict update in xdp paths of ena driver, from Shay
      Agroskin.

  25) seq_file iteration fix in sctp from Neil Brown.

  26) bpf 32-bit src register truncation fix on div/mod, from Daniel
      Borkmann.

  27) Fix jmp32 pruning in bpf verifier, from Daniel Borkmann.

  28) Fix locking in vsock_shutdown(), from Stefano Garzarella.

  29) Various missing index bound checks in hns3 driver, from Yufeng Mo.

  30) Flush ports on .phylink_mac_link_down() in dsa felix driver, from
      Vladimir Oltean.

  31) Don't mix up stp and mrp port states in bridge layer, from Horatiu
      Vultur.

  32) Fix locking during netif_tx_disable(), from Edwin Peer"

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (45 commits)
  bpf: Fix 32 bit src register truncation on div/mod
  bpf: Fix verifier jmp32 pruning decision logic
  bpf: Fix verifier jsgt branch analysis on max bound
  vsock: fix locking in vsock_shutdown()
  net: hns3: add a check for index in hclge_get_rss_key()
  net: hns3: add a check for tqp_index in hclge_get_ring_chain_from_mbx()
  net: hns3: add a check for queue_id in hclge_reset_vf_queue()
  net: dsa: felix: implement port flushing on .phylink_mac_link_down
  switchdev: mrp: Remove SWITCHDEV_ATTR_ID_MRP_PORT_STAT
  bridge: mrp: Fix the usage of br_mrp_port_switchdev_set_state
  net: watchdog: hold device global xmit lock during tx disable
  netfilter: nftables: relax check for stateful expressions in set definition
  netfilter: conntrack: skip identical origin tuple in same zone only
  vsock/virtio: update credit only if socket is not closed
  net: fix iteration for sctp transport seq_files
  net: ena: Update XDP verdict upon failure
  net/vmw_vsock: improve locking in vsock_connect_timeout()
  net/vmw_vsock: fix NULL pointer dereference
  ibmvnic: Clear failover_pending if unable to schedule
  net: stmmac: set TxQ mode back to DCB after disabling CBS
  ...

Merge misc fixes from Andrew Morton:
 "14 patches.

  Subsystems affected by this patch series: mm (kasan, mremap, tmpfs,
  selftests, memcg, and slub), MAINTAINERS, squashfs, nilfs2, and
  firmware"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  nilfs2: make splice write available again
  mm, slub: better heuristic for number of cpus when calculating slab order
  Revert "mm: memcontrol: avoid workload stalls when lowering memory.high"
  MAINTAINERS: update Andrey Ryabinin's email address
  selftests/vm: rename file run_vmtests to run_vmtests.sh
  tmpfs: disallow CONFIG_TMPFS_INODE64 on alpha
  tmpfs: disallow CONFIG_TMPFS_INODE64 on s390
  mm/mremap: fix BUILD_BUG_ON() error in get_extent
  firmware_loader: align .builtin_fw to 8
  kasan: fix stack traces dependency for HW_TAGS
  squashfs: add more sanity checks in xattr id lookup
  squashfs: add more sanity checks in inode lookup
  squashfs: add more sanity checks in id lookup
  squashfs: avoid out of bounds writes in decompressors

Since 5.10, splice() or sendfile() to NILFS2 return EINVAL.  This was
caused by commit 36e2c742 ("fs: don't allow splice read/write
without explicit ops").

This patch initializes the splice_write field in file_operations, like
most file systems do, to restore the functionality.

Link: https://lkml.kernel.org/r/1612784101-14353-1-git-send-email-konishi.ryusuke@gmail.comSigned-off-by: Joachim Henke <joachim.henke@t-systems.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>	[5.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When creating a new kmem cache, SLUB determines how large the slab pages
will based on number of inputs, including the number of CPUs in the
system.  Larger slab pages mean that more objects can be allocated/free
from per-cpu slabs before accessing shared structures, but also
potentially more memory can be wasted due to low slab usage and
fragmentation.  The rough idea of using number of CPUs is that larger
systems will be more likely to benefit from reduced contention, and also
should have enough memory to spare.

Number of CPUs used to be determined as nr_cpu_ids, which is number of
possible cpus, but on some systems many will never be onlined, thus
commit 045ab8c9 ("mm/slub: let number of online CPUs determine the
slub page order") changed it to nr_online_cpus().  However, for kmem
caches created early before CPUs are onlined, this may lead to
permamently low slab page sizes.

Vincent reports a regression [1] of hackbench on arm64 systems:

  "I'm facing significant performances regression on a large arm64
   server system (224 CPUs). Regressions is also present on small arm64
   system (8 CPUs) but in a far smaller order of magnitude

   On 224 CPUs system : 9 iterations of hackbench -l 16000 -g 16
   v5.11-rc4 : 9.135sec (+/- 0.45%)
   v5.11-rc4 + revert this patch: 3.173sec (+/- 0.48%)
   v5.10: 3.136sec (+/- 0.40%)"

Mel reports a regression [2] of hackbench on x86_64, with lockstat suggesting
page allocator contention:

  "i.e. the patch incurs a 7% to 32% performance penalty. This bisected
   cleanly yesterday when I was looking for the regression and then
   found the thread.

   Numerous caches change size. For example, kmalloc-512 goes from
   order-0 (vanilla) to order-2 with the revert.

   So mostly this is down to the number of times SLUB calls into the
   page allocator which only caches order-0 pages on a per-cpu basis"

Clearly num_online_cpus() doesn't work too early in bootup.  We could
change the order dynamically in a memory hotplug callback, but runtime
order changing for existing kmem caches has been already shown as
dangerous, and removed in 32a6f409 ("mm, slub: remove runtime
allocation order changes").

It could be resurrected in a safe manner with some effort, but to fix
the regression we need something simpler.

We could use num_present_cpus() that should be the number of physically
present CPUs even before they are onlined.  That would work for PowerPC
[3], which triggered the original commit, but that still doesn't work on
arm64 [4] as explained in [5].

So this patch tries to determine the best available value without
specific arch knowledge.

 - num_present_cpus() if the number is larger than 1, as that means the
   arch is likely setting it properly

 - nr_cpu_ids otherwise

This should fix the reported regressions while also keeping the effect
of 045ab8c9 for PowerPC systems.  It's possible there are
configurations where num_present_cpus() is 1 during boot while
nr_cpu_ids is at the same time bloated, so these (if they exist) would
keep the large orders based on nr_cpu_ids as was before 045ab8c9.

[1] https://lore.kernel.org/linux-mm/CAKfTPtA_JgMf_+zdFbcb_V9rM7JBWNPjAz9irgwFj7Rou=xzZg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mm/20210128134512.GF3592@techsingularity.net/
[3] https://lore.kernel.org/linux-mm/20210123051607.GC2587010@in.ibm.com/
[4] https://lore.kernel.org/linux-mm/CAKfTPtAjyVmS5VYvU6DBxg4-JEo5bdmWbngf-03YsY18cmWv_g@mail.gmail.com/
[5] https://lore.kernel.org/linux-mm/20210126230305.GD30941@willie-the-truck/

Link: https://lkml.kernel.org/r/20210208134108.22286-1-vbabka@suse.cz
Fixes: 045ab8c9 ("mm/slub: let number of online CPUs determine the slub page order")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Vincent Guittot <vincent.guittot@linaro.org>
Reported-by: Mel Gorman <mgorman@techsingularity.net>
Tested-by: Mel Gorman <mgorman@techsingularity.net>
Tested-by: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Bharata B Rao <bharata@linux.ibm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Jann Horn <jannh@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Will Deacon <will@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fixes the following warnings which results in interrupts disabled on
port B/F:

gpio gpiochip1: (B): detected irqchip that is shared with multiple gpiochips: please fix the driver.
gpio gpiochip5: (F): detected irqchip that is shared with multiple gpiochips: please fix the driver.

- added separate irqchip for each interrupt capable gpiochip
- provided unique names for each irqchip

Fixes: d2b09196 ("gpio: ep93xx: Pass irqchip when adding gpiochip")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Two index spaces and ep93xx_gpio_port are confusing.

Instead add a separate struct to store necessary data and remove
ep93xx_gpio_port.

- add struct to store IRQ related data for each IRQ capable chip
- replace offset array with defined offsets
- add IRQ registers offset for each IRQ capable chip into
  ep93xx_gpio_banks

------------[ cut here ]------------
kernel BUG at drivers/gpio/gpio-ep93xx.c:64!
---[ end trace 3f6544e133e9f5ae ]---

Fixes: fd935fc4 ("gpio: ep93xx: Do not pingpong irq numbers")
Cc: <stable@vger.kernel.org>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Merely enabling CONFIG_COMPILE_TEST should not enable additional code.
To fix this, restrict the automatic enabling of GPIO_MXS to ARCH_MXS,
and ask the user in case of compile-testing.

Fixes: 6876ca31 ("gpio: mxs: add COMPILE_TEST support for GPIO_MXS")
Cc: <stable@vger.kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

It turns out that reasoning for lowering max. supported frequency is
wrong. Scrambling works just fine. Several now fixed bugs prevented
proper functioning, even with rates lower than 340 MHz. Issues were just
more pronounced with higher frequencies.

Fix that by allowing max. supported frequency in HW and fix the comment.

Fixes: cd906375 ("drm/sun4i: DW HDMI: Lower max. supported rate for H6")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209175900.7092-6-jernej.skrabec@siol.net

As it turns out, vendor HDMI PHY driver for H6 has a pretty big table
of predefined values for various pixel clocks. However, most of them are
not useful/tested because they come from reference driver code. Vendor
PHY driver is concerned with only few of those, namely 27 MHz, 74.25
MHz, 148.5 MHz, 297 MHz and 594 MHz. These are all frequencies for
standard CEA modes.

Fix sun50i_h6_cur_ctr and sun50i_h6_phy_config with the values only for
aforementioned frequencies.

Table sun50i_h6_mpll_cfg doesn't need to be changed because values are
actually frequency dependent and not so much SoC dependent. See i.MX6
documentation for explanation of those values for similar PHY.

Fixes: c71c9b2f ("drm/sun4i: Add support for Synopsys HDMI PHY")
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209175900.7092-5-jernej.skrabec@siol.net

As expected, HDMI controller clock should always match pixel clock. In
the past, changing HDMI controller rate would seemingly worsen
situation. However, that was the result of other bugs which are now
fixed.

Fix that by removing set_rate quirk and always set clock rate.

Fixes: 40bb9d31 ("drm/sun4i: Add support for H6 DW HDMI controller")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209175900.7092-4-jernej.skrabec@siol.net

Channel 1 has polarity bits for vsync and hsync signals but driver never
sets them. It turns out that with pre-HDMI2 controllers seemingly there
is no issue if polarity is not set. However, with HDMI2 controllers
(H6) there often comes to de-synchronization due to phase shift. This
causes flickering screen. It's safe to assume that similar issues might
happen also with pre-HDMI2 controllers.

Solve issue with setting vsync and hsync polarity. Note that display
stacks with tcon top have polarity bits actually in tcon0 polarity
register.

Fixes: 9026e0d1 ("drm: Add Allwinner A10 Display Engine support")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209175900.7092-3-jernej.skrabec@siol.net

We don't have a persistent fb holding a reference to the frontbuffer
object, so every time we do the get+put we throw the frontbuffer object
immediately away. And so the next time around we get a pristine
frontbuffer object with bits==0 even for the old vma. This confuses
the frontbuffer tracking code which understandably expects the old
frontbuffer to have the overlay's bit set.

Fix this by hanging on to the frontbuffer reference until the next
flip. And just to make this a bit more clear let's track the frontbuffer
explicitly instead of just grabbing it via the old vma.

Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1136Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209021918.16234-2-ville.syrjala@linux.intel.com
Fixes: 8e7cb179 ("drm/i915: Extract intel_frontbuffer active tracking")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 553c23bd)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

This reverts commit 4a3dea89.

This causes blank screens for some users.

Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1482
Cc: Alvin Lee <alvin.lee2@amd.com>
Cc: Jun Lei <Jun.Lei@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Daniel Borkmann says:

====================
pull-request: bpf 2021-02-10

The following pull-request contains BPF updates for your *net* tree.

We've added 5 non-merge commits during the last 8 day(s) which contain
a total of 3 files changed, 22 insertions(+), 21 deletions(-).

The main changes are:

1) Fix missed execution of kprobes BPF progs when kprobe is firing via
   int3, from Alexei Starovoitov.

2) Fix potential integer overflow in map max_entries for stackmap on
   32 bit archs, from Bui Quang Minh.

3) Fix a verifier pruning and a insn rewrite issue related to 32 bit ops,
   from Daniel Borkmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
c# Please enter a commit message to explain why this merge is necessary,

This reverts commit 536d3bf2, as it can
cause writers to memory.high to get stuck in the kernel forever,
performing page reclaim and consuming excessive amounts of CPU cycles.

Before the patch, a write to memory.high would first put the new limit
in place for the workload, and then reclaim the requested delta.  After
the patch, the kernel tries to reclaim the delta before putting the new
limit into place, in order to not overwhelm the workload with a sudden,
large excess over the limit.  However, if reclaim is actively racing
with new allocations from the uncurbed workload, it can keep the write()
working inside the kernel indefinitely.

This is causing problems in Facebook production.  A privileged
system-level daemon that adjusts memory.high for various workloads
running on a host can get unexpectedly stuck in the kernel and
essentially turn into a sort of involuntary kswapd for one of the
workloads.  We've observed that daemon busy-spin in a write() for
minutes at a time, neglecting its other duties on the system, and
expending privileged system resources on behalf of a workload.

To remedy this, we have first considered changing the reclaim logic to
break out after a couple of loops - whether the workload has converged
to the new limit or not - and bound the write() call this way.  However,
the root cause that inspired the sequence change in the first place has
been fixed through other means, and so a revert back to the proven
limit-setting sequence, also used by memory.max, is preferable.

The sequence was changed to avoid extreme latencies in the workload when
the limit was lowered: the sudden, large excess created by the limit
lowering would erroneously trigger the penalty sleeping code that is
meant to throttle excessive growth from below.  Allocating threads could
end up sleeping long after the write() had already reclaimed the delta
for which they were being punished.

However, erroneous throttling also caused problems in other scenarios at
around the same time.  This resulted in commit b3ff9291 ("mm, memcg:
reclaim more aggressively before high allocator throttling"), included
in the same release as the offending commit.  When allocating threads
now encounter large excess caused by a racing write() to memory.high,
instead of entering punitive sleeps, they will simply be tasked with
helping reclaim down the excess, and will be held no longer than it
takes to accomplish that.  This is in line with regular limit
enforcement - i.e.  if the workload allocates up against or over an
otherwise unchanged limit from below.

With the patch breaking userspace, and the root cause addressed by other
means already, revert it again.

Link: https://lkml.kernel.org/r/20210122184341.292461-1-hannes@cmpxchg.org
Fixes: 536d3bf2 ("mm: memcontrol: avoid workload stalls when lowering memory.high")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Tejun Heo <tj@kernel.org>
Acked-by: Chris Down <chris@chrisdown.name>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Michal Koutný <mkoutny@suse.com>
Cc: <stable@vger.kernel.org>	[5.8+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Update my email, @virtuozzo.com will stop working shortly.

Link: https://lkml.kernel.org/r/20210204223904.3824-1-ryabinin.a.a@gmail.comSigned-off-by: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit c2aa8afc has renamed run_vmtests in Makefile, but the file
still uses the old name.

The kernel test robot reported the following issue:

  # selftests: vm: run_vmtests.sh
  # Warning: file run_vmtests.sh is missing!
  not ok 1 selftests: vm: run_vmtests.sh

Link: https://lkml.kernel.org/r/20210205085507.1479894-1-rong.a.chen@intel.com
Fixes: c2aa8afc (selftests/vm: rename run_vmtests --> run_vmtests.sh)
Signed-off-by: Rong Chen <rong.a.chen@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

As with s390, alpha is a 64-bit architecture with a 32-bit ino_t.  With
CONFIG_TMPFS_INODE64=y tmpfs mounts will get 64-bit inode numbers and
display "inode64" in the mount options, whereas passing "inode64" in the
mount options will fail.  This leads to erroneous behaviours such as
this:

  # mkdir mnt
  # mount -t tmpfs nodev mnt
  # mount -o remount,rw mnt
  mount: /home/ubuntu/mnt: mount point not mounted or bad option.

Prevent CONFIG_TMPFS_INODE64 from being selected on alpha.

Link: https://lkml.kernel.org/r/20210208215726.608197-1-seth.forshee@canonical.com
Fixes: ea3271f7 ("tmpfs: support 64-bit inums per-sb")
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Chris Down <chris@chrisdown.name>
Cc: Amir Goldstein <amir73il@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: <stable@vger.kernel.org>	[5.9+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently there is an assumption in tmpfs that 64-bit architectures also
have a 64-bit ino_t.  This is not true on s390 which has a 32-bit ino_t.
With CONFIG_TMPFS_INODE64=y tmpfs mounts will get 64-bit inode numbers
and display "inode64" in the mount options, but passing the "inode64"
mount option will fail.  This leads to the following behavior:

  # mkdir mnt
  # mount -t tmpfs nodev mnt
  # mount -o remount,rw mnt
  mount: /home/ubuntu/mnt: mount point not mounted or bad option.

As mount sees "inode64" in the mount options and thus passes it in the
options for the remount.

So prevent CONFIG_TMPFS_INODE64 from being selected on s390.

Link: https://lkml.kernel.org/r/20210205230620.518245-1-seth.forshee@canonical.com
Fixes: ea3271f7 ("tmpfs: support 64-bit inums per-sb")
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Chris Down <chris@chrisdown.name>
Cc: Hugh Dickins <hughd@google.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: <stable@vger.kernel.org>	[5.9+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

clang can't evaluate this function argument at compile time when the
function is not inlined, which leads to a link time failure:

  ld.lld: error: undefined symbol: __compiletime_assert_414
  >>> referenced by mremap.c
  >>>               mremap.o:(get_extent) in archive mm/built-in.a

Mark the function as __always_inline to avoid it.

Link: https://lkml.kernel.org/r/20201230154104.522605-1-arnd@kernel.org
Fixes: 9ad9718b ("mm/mremap: calculate extent in one place")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: Brian Geffon <bgeffon@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>