NFDK firmware supports 48-bit dma addressing and
parses 16 high bits of dma addresses.

In nfp_nfdk_tx_desc, dma related structure and tso
related structure are union. When "mss" be filled
with nonzero value due to enable tso, the memory used
by "padding" may be also filled. Then, firmware may
parse wrong dma addresses which causes TX watchdog
timeout problem.

This patch removes padding and unifies the dma_addr_hi
bits with the one in firmware. nfp_nfdk_tx_desc_set_dma_addr
is also added to match this change.

Fixes: c10d12e3 ("nfp: add support for NFDK data path")
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220601083449.50556-1-simon.horman@corigine.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

There are session cleanup problems in ax25_release() and
ax25_disconnect(). If we setup a session and then disconnect,
the disconnected session is still in "LISTENING" state that
is shown below.

Active AX.25 sockets
Dest       Source     Device  State        Vr/Vs    Send-Q  Recv-Q
DL9SAU-4   DL9SAU-3   ???     LISTENING    000/000  0       0
DL9SAU-3   DL9SAU-4   ???     LISTENING    000/000  0       0

The first reason is caused by del_timer_sync() in ax25_release().
The timers of ax25 are used for correct session cleanup. If we use
ax25_release() to close ax25 sessions and ax25_dev is not null,
the del_timer_sync() functions in ax25_release() will execute.
As a result, the sessions could not be cleaned up correctly,
because the timers have stopped.

In order to solve this problem, this patch adds a device_up flag
in ax25_dev in order to judge whether the device is up. If there
are sessions to be cleaned up, the del_timer_sync() in
ax25_release() will not execute. What's more, we add ax25_cb_del()
in ax25_kill_by_device(), because the timers have been stopped
and there are no functions that could delete ax25_cb if we do not
call ax25_release(). Finally, we reorder the position of
ax25_list_lock in ax25_cb_del() in order to synchronize among
different functions that call ax25_cb_del().

The second reason is caused by improper check in ax25_disconnect().
The incoming ax25 sessions which ax25->sk is null will close
heartbeat timer, because the check "if(!ax25->sk || ..)" is
satisfied. As a result, the session could not be cleaned up properly.

In order to solve this problem, this patch changes the improper
check to "if(ax25->sk && ..)" in ax25_disconnect().

What`s more, the ax25_disconnect() may be called twice, which is
not necessary. For example, ax25_kill_by_device() calls
ax25_disconnect() and sets ax25->state to AX25_STATE_0, but
ax25_release() calls ax25_disconnect() again.

In order to solve this problem, this patch add a check in
ax25_release(). If the flag of ax25->sk equals to SOCK_DEAD,
the ax25_disconnect() in ax25_release() should not be executed.

Fixes: 82e31755 ("ax25: Fix UAF bugs in ax25 timers")
Fixes: 8a367e74 ("ax25: Fix segfault after sock connection timeout")
Reported-and-tested-by: Thomas Osterried <thomas@osterried.de>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220530152158.108619-1-duoming@zju.edu.cnSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Adding support for Cinterion device MV31 with Qualcomm
new baseline. Use different PIDs to separate it from
previous base line products.
All interfaces settings keep same as previous.

T:  Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  7 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1e2d ProdID=00b9 Rev=04.14
S:  Manufacturer=Cinterion
S:  Product=Cinterion PID 0x00B9 USB Mobile Broadband
S:  SerialNumber=90418e79
C:  #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
I:  If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20220601040531.6016-1-slark_xiao@163.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Saeed Mahameed says:

====================
mlx5 fixes 2022-05-31

This series provides bug fixes to mlx5 driver.
Please pull and let me know if there is any problem.

* tag 'mlx5-fixes-2022-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
  net/mlx5: Fix mlx5_get_next_dev() peer device matching
  net/mlx5e: Update netdev features after changing XDP state
  net/mlx5: correct ECE offset in query qp output
  net/mlx5e: Disable softirq in mlx5e_activate_rq to avoid race condition
  net/mlx5: CT: Fix header-rewrite re-use for tupels
  net/mlx5e: TC NIC mode, fix tc chains miss table
  net/mlx5: Don't use already freed action pointer
====================

Link: https://lore.kernel.org/r/20220531205447.99236-1-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Íñigo Huguet says:

====================
sfc/siena: fix some efx_separate_tx_channels errors

Trying to load sfc driver with modparam efx_separate_tx_channels=1
resulted in errors during initialization and not being able to use the
NIC. This patches fix a few bugs and make it work again.

This has been already done for sfc, do it also for sfc_siena.
====================

Link: https://lore.kernel.org/r/20220601063603.15362-1-ihuguet@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

tx_channel_offset is calculated in efx_allocate_msix_channels, but it is
also calculated again in efx_set_channels because it was originally done
there, and when efx_allocate_msix_channels was introduced it was
forgotten to be removed from efx_set_channels.

Moreover, the old calculation is wrong when using
efx_separate_tx_channels because now we can have XDP channels after the
TX channels, so n_channels - n_tx_channels doesn't point to the first TX
channel.

Remove the old calculation from efx_set_channels, and add the
initialization of this variable if MSI or legacy interrupts are used,
next to the initialization of the rest of the related variables, where
it was missing.

This has been already done for sfc, do it also for sfc_siena.

Fixes: 3990a8ff ("sfc: allocate channels for XDP tx queues")
Reported-by: Tianhao Zhao <tizhao@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Normally, all channels have RX and TX queues, but this is not true if
modparam efx_separate_tx_channels=1 is used. In that cases, some
channels only have RX queues and others only TX queues (or more
preciselly, they have them allocated, but not initialized).

Fix efx_channel_has_tx_queues to return the correct value for this case
too.

This has been already done for sfc, do it also for sfc_siena.

Messages shown at probe time before the fix:
 sfc 0000:03:00.0 ens6f0np0: MC command 0x82 inlen 544 failed rc=-22 (raw=0) arg=0
 ------------[ cut here ]------------
 netdevice: ens6f0np0: failed to initialise TXQ -1
 WARNING: CPU: 1 PID: 626 at drivers/net/ethernet/sfc/ef10.c:2393 efx_ef10_tx_init+0x201/0x300 [sfc]
 [...] stripped
 RIP: 0010:efx_ef10_tx_init+0x201/0x300 [sfc]
 [...] stripped
 Call Trace:
  efx_init_tx_queue+0xaa/0xf0 [sfc]
  efx_start_channels+0x49/0x120 [sfc]
  efx_start_all+0x1f8/0x430 [sfc]
  efx_net_open+0x5a/0xe0 [sfc]
  __dev_open+0xd0/0x190
  __dev_change_flags+0x1b3/0x220
  dev_change_flags+0x21/0x60
 [...] stripped

Messages shown at remove time before the fix:
 sfc 0000:03:00.0 ens6f0np0: failed to flush 10 queues
 sfc 0000:03:00.0 ens6f0np0: failed to flush queues

Fixes: 8700aff0 ("sfc: fix channel allocation with brute force")
Reported-by: Tianhao Zhao <tizhao@redhat.com>
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Tested-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Steffen Klassert says:

====================
ipsec 2022-06-01

1) Revert "net: af_key: add check for pfkey_broadcast in function pfkey_process"
   From Michal Kubecek.

2) Don't set IPv4 DF bit when encapsulating IPv6 frames below 1280 bytes.
   From Maciej Żenczykowski.

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
  xfrm: do not set IPv4 DF flag when encapsulating IPv6 frames <= 1280 bytes.
  Revert "net: af_key: add check for pfkey_broadcast in function pfkey_process"
====================

Link: https://lore.kernel.org/r/20220601103349.2297361-1-steffen.klassert@secunet.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Kalle Valo says:

====================
wireless fixes for v5.19

First set of fixes for v5.19. Build fixes for iwlwifi and libertas, a
scheduling while atomic fix for rtw88 and use-after-free fix for
mac80211.

* tag 'wireless-2022-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
  wifi: mac80211: fix use-after-free in chanctx code
  wifi: rtw88: add a work to correct atomic scheduling warning of ::set_tim
  wifi: iwlwifi: pcie: rename CAUSE macro
  wifi: libertas: use variable-size data in assoc req/resp cmd
====================

Link: https://lore.kernel.org/r/20220601110741.90B28C385A5@smtp.kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Use plain 255 instead, which also avoid introducing an additional header
dependency on <linux/types.h>

Fixes: 26859240 ("txhash: Add socket option to control TX hash rethink behavior")
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20220531094345.13801-1-tklauser@distanz.chSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The tcf_ct_flow_table_fill_tuple_ipv6() function is supposed to return
false on failure.  It should not return negatives because that means
succes/true.

Fixes: fcb6aa86 ("act_ct: Support GRE offload")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Link: https://lore.kernel.org/r/YpYFnbDxFl6tQ3Bn@kiliSigned-off-by: Paolo Abeni <pabeni@redhat.com>

When passing interface parameter to ping -6:
$ ping -6 ::11:141:84:9 -I eth2
Results in:
PING ::11:141:84:10(::11:141:84:10) from ::11:141:84:9 eth2: 56 data bytes
ping: sendmsg: Invalid argument
ping: sendmsg: Invalid argument

Initialize the fl6's outgoing interface (OIF) before triggering
ip6_datagram_send_ctl. Don't wipe fl6 after ip6_datagram_send_ctl() as
changes in fl6 that may happen in the function are overwritten explicitly.
Update comment accordingly.

Fixes: 13651224 ("net: ping6: support setting basic SOL_IPV6 options via cmsg")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220531084544.15126-1-tariqt@nvidia.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Create a new macsec device but not get reference to real_dev. That can
not ensure that real_dev is freed after macsec. That will trigger the
UAF bug for real_dev as following:

==================================================================
BUG: KASAN: use-after-free in macsec_get_iflink+0x5f/0x70 drivers/net/macsec.c:3662
Call Trace:
 ...
 macsec_get_iflink+0x5f/0x70 drivers/net/macsec.c:3662
 dev_get_iflink+0x73/0xe0 net/core/dev.c:637
 default_operstate net/core/link_watch.c:42 [inline]
 rfc2863_policy+0x233/0x2d0 net/core/link_watch.c:54
 linkwatch_do_dev+0x2a/0x150 net/core/link_watch.c:161

Allocated by task 22209:
 ...
 alloc_netdev_mqs+0x98/0x1100 net/core/dev.c:10549
 rtnl_create_link+0x9d7/0xc00 net/core/rtnetlink.c:3235
 veth_newlink+0x20e/0xa90 drivers/net/veth.c:1748

Freed by task 8:
 ...
 kfree+0xd6/0x4d0 mm/slub.c:4552
 kvfree+0x42/0x50 mm/util.c:615
 device_release+0x9f/0x240 drivers/base/core.c:2229
 kobject_cleanup lib/kobject.c:673 [inline]
 kobject_release lib/kobject.c:704 [inline]
 kref_put include/linux/kref.h:65 [inline]
 kobject_put+0x1c8/0x540 lib/kobject.c:721
 netdev_run_todo+0x72e/0x10b0 net/core/dev.c:10327

After commit faab39f6 ("net: allow out-of-order netdev unregistration")
and commit e5f80fcf ("ipv6: give an IPv6 dev to blackhole_netdev"), we
can add dev_hold_track() in macsec_dev_init() and dev_put_track() in
macsec_free_netdev() to fix the problem.

Fixes: 2bce1ebe ("macsec: fix refcnt leak in module exit routine")
Reported-by: syzbot+d0e94b65ac259c29ce7a@syzkaller.appspotmail.com
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/r/20220531074500.1272846-1-william.xuanziyang@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The is_valid_offset() function returns success/true if the call to
validate_and_get_cpt_blkaddr() fails.

Fixes: ecad2ce8 ("octeontx2-af: cn10k: Add mailbox to configure reassembly timeout")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YpXDrTPb8qV01JSP@kiliSigned-off-by: Paolo Abeni <pabeni@redhat.com>

In ieee80211_vif_use_reserved_context(), when we have an
old context and the new context's replace_state is set to
IEEE80211_CHANCTX_REPLACE_NONE, we free the old context
in ieee80211_vif_use_reserved_reassign(). Therefore, we
cannot check the old_ctx anymore, so we should set it to
NULL after this point.

However, since the new_ctx replace state is clearly not
IEEE80211_CHANCTX_REPLACES_OTHER, we're not going to do
anything else in this function and can just return to
avoid accessing the freed old_ctx.

Cc: stable@vger.kernel.org
Fixes: 5bcae31d ("mac80211: implement multi-vif in-place reservations")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220601091926.df419d91b165.I17a9b3894ff0b8323ce2afdb153b101124c821e5@changeid

Guard ns_targets in struct bond_params by CONFIG_IPV6, which could save
256 bytes if IPv6 not configed. Also add this protection for function
bond_is_ip6_target_ok() and bond_get_targets_ip6().

Remove the IS_ENABLED() check for bond_opts[] as this will make
BOND_OPT_NS_TARGETS uninitialized if CONFIG_IPV6 not enabled. Add
a dummy bond_option_ns_ip6_targets_set() for this situation.

Fixes: 4e24be01 ("bonding: add new parameter ns_targets")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Link: https://lore.kernel.org/r/20220531063727.224043-1-liuhangbin@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Laurent reported the enclosed report [1]

This bug triggers with following coditions:

0) Kernel built with CONFIG_DEBUG_PREEMPT=y

1) A new passive FastOpen TCP socket is created.
   This FO socket waits for an ACK coming from client to be a complete
   ESTABLISHED one.
2) A socket operation on this socket goes through lock_sock()
   release_sock() dance.
3) While the socket is owned by the user in step 2),
   a retransmit of the SYN is received and stored in socket backlog.
4) At release_sock() time, the socket backlog is processed while
   in process context.
5) A SYNACK packet is cooked in response of the SYN retransmit.
6) -> tcp_rtx_synack() is called in process context.

Before blamed commit, tcp_rtx_synack() was always called from BH handler,
from a timer handler.

Fix this by using TCP_INC_STATS() & NET_INC_STATS()
which do not assume caller is in non preemptible context.

[1]
BUG: using __this_cpu_add() in preemptible [00000000] code: epollpep/2180
caller is tcp_rtx_synack.part.0+0x36/0xc0
CPU: 10 PID: 2180 Comm: epollpep Tainted: G           OE     5.16.0-0.bpo.4-amd64 #1  Debian 5.16.12-1~bpo11+1
Hardware name: Supermicro SYS-5039MC-H8TRF/X11SCD-F, BIOS 1.7 11/23/2021
Call Trace:
 <TASK>
 dump_stack_lvl+0x48/0x5e
 check_preemption_disabled+0xde/0xe0
 tcp_rtx_synack.part.0+0x36/0xc0
 tcp_rtx_synack+0x8d/0xa0
 ? kmem_cache_alloc+0x2e0/0x3e0
 ? apparmor_file_alloc_security+0x3b/0x1f0
 inet_rtx_syn_ack+0x16/0x30
 tcp_check_req+0x367/0x610
 tcp_rcv_state_process+0x91/0xf60
 ? get_nohz_timer_target+0x18/0x1a0
 ? lock_timer_base+0x61/0x80
 ? preempt_count_add+0x68/0xa0
 tcp_v4_do_rcv+0xbd/0x270
 __release_sock+0x6d/0xb0
 release_sock+0x2b/0x90
 sock_setsockopt+0x138/0x1140
 ? __sys_getsockname+0x7e/0xc0
 ? aa_sk_perm+0x3e/0x1a0
 __sys_setsockopt+0x198/0x1e0
 __x64_sys_setsockopt+0x21/0x30
 do_syscall_64+0x38/0xc0
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Fixes: 168a8f58 ("tcp: TCP Fast Open Server - main code path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Laurent Fasnacht <laurent.fasnacht@proton.ch>
Acked-by: Neal Cardwell <ncardwell@google.com>
Link: https://lore.kernel.org/r/20220530213713.601888-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

1) Missing proper sanitization for nft_set_desc_concat_parse().

2) Missing mutex in nf_tables pre_exit path.

3) Possible double hook unregistration from clean_net path.

4) Missing FLOWI_FLAG_ANYSRC flag in flowtable route lookup.
   Fix incorrect source and destination address in case of NAT.
   Patch from wenxu.

* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
  netfilter: flowtable: fix nft_flow_route source address for nat case
  netfilter: flowtable: fix missing FLOWI_FLAG_ANYSRC flag
  netfilter: nf_tables: double hook unregistration in netns path
  netfilter: nf_tables: hold mutex on netns pre_exit path
  netfilter: nf_tables: sanitize nft_set_desc_concat_parse()
====================

Link: https://lore.kernel.org/r/20220531215839.84765-1-pablo@netfilter.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In qdisc_run_end(), the spin_unlock() only has store-release semantic,
which guarantees all earlier memory access are visible before it. But
the subsequent test_bit() has no barrier semantics so may be reordered
ahead of the spin_unlock(). The store-load reordering may cause a packet
stuck problem.

The concurrent operations can be described as below,
         CPU 0                      |          CPU 1
   qdisc_run_end()                  |     qdisc_run_begin()
          .                         |           .
 ----> /* may be reorderd here */   |           .
|         .                         |           .
|     spin_unlock()                 |         set_bit()
|         .                         |         smp_mb__after_atomic()
 ---- test_bit()                    |         spin_trylock()
          .                         |          .

Consider the following sequence of events:
    CPU 0 reorder test_bit() ahead and see MISSED = 0
    CPU 1 calls set_bit()
    CPU 1 calls spin_trylock() and return fail
    CPU 0 executes spin_unlock()

At the end of the sequence, CPU 0 calls spin_unlock() and does nothing
because it see MISSED = 0. The skb on CPU 1 has beed enqueued but no one
take it, until the next cpu pushing to the qdisc (if ever ...) will
notice and dequeue it.

This patch fix this by adding one explicit barrier. As spin_unlock() and
test_bit() ordering is a store-load ordering, a full memory barrier
smp_mb() is needed here.

Fixes: a90c57f2 ("net: sched: fix packet stuck problem for lockless qdisc")
Signed-off-by: Guoju Fang <gjfang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220528101628.120193-1-gjfang@linux.alibaba.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

For snat and dnat cases, the saddr should be taken from reverse tuple.

Fixes: 3412e164 (netfilter: flowtable: nft_flow_route use more data for reverse route)
Signed-off-by: wenxu <wenxu@chinatelecom.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

The nf_flow_table gets route through ip_route_output_key. If the saddr
is not local one, then FLOWI_FLAG_ANYSRC flag should be set. Without
this flag, the route lookup for other_dst will fail.

Fixes: 3412e164 (netfilter: flowtable: nft_flow_route use more data for reverse route)
Signed-off-by: wenxu <wenxu@chinatelecom.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

__nft_release_hooks() is called from pre_netns exit path which
unregisters the hooks, then the NETDEV_UNREGISTER event is triggered
which unregisters the hooks again.

[  565.221461] WARNING: CPU: 18 PID: 193 at net/netfilter/core.c:495 __nf_unregister_net_hook+0x247/0x270
[...]
[  565.246890] CPU: 18 PID: 193 Comm: kworker/u64:1 Tainted: G            E     5.18.0-rc7+ #27
[  565.253682] Workqueue: netns cleanup_net
[  565.257059] RIP: 0010:__nf_unregister_net_hook+0x247/0x270
[...]
[  565.297120] Call Trace:
[  565.300900]  <TASK>
[  565.304683]  nf_tables_flowtable_event+0x16a/0x220 [nf_tables]
[  565.308518]  raw_notifier_call_chain+0x63/0x80
[  565.312386]  unregister_netdevice_many+0x54f/0xb50

Unregister and destroy netdev hook from netns pre_exit via kfree_rcu
so the NETDEV_UNREGISTER path see unregistered hooks.

Fixes: 767d1216 ("netfilter: nftables: fix possible UAF over chains from packet path in netns")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

clean_net() runs in workqueue while walking over the lists, grab mutex.

Fixes: 767d1216 ("netfilter: nftables: fix possible UAF over chains from packet path in netns")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Add several sanity checks for nft_set_desc_concat_parse():

- validate desc->field_count not larger than desc->field_len array.
- field length cannot be larger than desc->field_len (ie. U8_MAX)
- total length of the concatenation cannot be larger than register array.

Joint work with Florian Westphal.

Fixes: f3a2181e ("netfilter: nf_tables: Support for sets with multiple ranged fields")
Reported-by: <zhangziming.zzm@antgroup.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

In some use-cases, mlx5 instances will need to search for their peer
device (the other port on the same HCA). For that, mlx5 device matching
mechanism relied on auxiliary_find_device() to search, and used a bad matching
callback function.

This approach has two issues:

1) next_phys_dev() the matching function, assumed all devices are
   of the type mlx5_adev (mlx5 auxiliary device) which is wrong and
   could lead to crashes, this worked for a while, since only lately
   other drivers started registering auxiliary devices.

2) using the auxiliary class bus (auxiliary_find_device) to search for
   mlx5_core_dev devices, who are actually PCIe device instances, is wrong.
   This works since mlx5_core always has at least one mlx5_adev instance
   hanging around in the aux bus.

As suggested by others we can fix 1. by comparing device names prefixes
if they have the string "mlx5_core" in them, which is not a best practice !
but even with that fixed, still 2. needs fixing, we are trying to
match pcie device peers so we should look in the right bus (pci bus),
hence this fix.

The fix:
1) search the pci bus for mlx5 peer devices, instead of the aux bus
2) to validated devices are the same type "mlx5_core_dev" compare if
   they have the same driver, which is bulletproof.

   This wouldn't have worked with the aux bus since the various mlx5 aux
   device types don't share the same driver, even if they share the same device
   wrapper struct (mlx5_adev) "which helped to find the parent device"

Fixes: a925b5e3 ("net/mlx5: Register mlx5 devices to auxiliary virtual bus")
Reported-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reported-by: Maher Sanalla <msanalla@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maher Sanalla <msanalla@nvidia.com>

Some features (LRO, HW GRO) conflict with XDP. If there is an attempt to
enable such features while XDP is active, they will be set to `off
[requested on]`. In order to activate these features after XDP is turned
off, the driver needs to call netdev_update_features(). This commit adds
this missing call after XDP state changes.

Fixes: cf6e34c8 ("net/mlx5e: Properly block LRO when XDP is enabled")
Fixes: b0617e7b ("net/mlx5e: Properly block HW GRO when XDP is enabled")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

ECE field should be after opt_param_mask in query qp output.

Fixes: 6b646a7e ("net/mlx5: Add ability to read and write ECE options")
Signed-off-by: Changcheng Liu <jerrliu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

When the driver activates the channels, it assumes NAPI isn't running
yet. mlx5e_activate_rq posts a NOP WQE to ICOSQ to trigger a hardware
interrupt and start NAPI, which will run mlx5e_alloc_rx_mpwqe and post
UMR WQEs to ICOSQ to be able to receive packets with striding RQ.

Unfortunately, a race condition is possible if NAPI is triggered by
something else (for example, TX) at a bad timing, before
mlx5e_activate_rq finishes. In this case, mlx5e_alloc_rx_mpwqe may post
UMR WQEs to ICOSQ, and with the bad timing, the wqe_info of the first
UMR may be overwritten by the wqe_info of the NOP posted by
mlx5e_activate_rq.

The consequence is that icosq->db.wqe_info[0].num_wqebbs will be changed
from MLX5E_UMR_WQEBBS to 1, disrupting the integrity of the array-based
linked list in wqe_info[]. mlx5e_poll_ico_cq will hang in an infinite
loop after processing wqe_info[0], because after the corruption, the
next item to be processed will be wqe_info[1], which is filled with
zeros, and `sqcc += wi->num_wqebbs` will never move further.

This commit fixes this race condition by using async_icosq to post the
NOP and trigger the interrupt. async_icosq is always protected with a
spinlock, eliminating the race condition.

Fixes: bc77b240 ("net/mlx5e: Add fragmented memory support for RX multi packet WQE")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reported-by: Karsten Nielsen <karsten@foo-bar.dk>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Tuple entries that don't have nat configured for them
which are added to the ct nat table will always create
a new modify header, as we don't check for possible
re-use on them. The same for tuples that have nat configured
for them but are added to ct table.

Fix the above by only avoiding wasteful re-use lookup
for actually natted entries in ct nat table.

Fixes: 7fac5c2e ("net/mlx5: CT: Avoid reusing modify header context for natted entries")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The cited commit changed promisc table to be created on demand with the
highest priority in the NIC table replacing the vlan table, this caused
tc NIC tables miss flow to skip the prmoisc table because it use vlan
table as miss table.

OVS offload in NIC mode use promisc by default so any unicast packet
which will be handled by tc NIC tables miss flow will skip the promisc
rule and will be dropped.

Fix this by adding new empty table in new tc level with low priority and
point the nic tc chain miss to it, the new table is managed so it will
point to vlan table if promisc is disabled and to promisc table if enabled.

Fixes: 1c46d740 ("net/mlx5e: Optimize promiscuous mode")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The call to mlx5dr_action_destroy() releases "action" memory. That
pointer is set to miss_action later and generates the following smatch
error:

 drivers/net/ethernet/mellanox/mlx5/core/steering/fs_dr.c:53 set_miss_action()
 warn: 'action' was already freed.

Make sure that the pointer is always valid by setting NULL after destroy.

Fixes: 6a48faee ("net/mlx5: Add direct rule fs_cmd implementation")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Commit 6fac592c ("xen: update ring.h") missed to fix one use case
of RING_HAS_UNCONSUMED_REQUESTS().
Reported-by: Jan Beulich <jbeulich@suse.com>
Fixes: 6fac592c ("xen: update ring.h")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/20220530113459.20124-1-jgross@suse.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

RFC 9131 changes default behaviour of handling RX of NA messages when the
corresponding entry is absent in the neighbour cache. The current
implementation is limited to accept just unsolicited NAs. However, the
RFC is more generic where it also accepts solicited NAs. Both types
should result in adding a STALE entry for this case.

Expand accept_untracked_na behaviour to also accept solicited NAs to
be compliant with the RFC and rename the sysctl knob to
accept_untracked_na.

Fixes: f9a2fb73 ("net/ipv6: Introduce accept_unsolicited_na knob to implement router-side changes for RFC9131")
Signed-off-by: Arun Ajith S <aajith@arista.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220530101414.65439-1-aajith@arista.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

When adding bond new parameter ns_targets. I forgot to print this
in bond master proc info. After updating, the bond master info will look
like:

ARP IP target/s (n.n.n.n form): 192.168.1.254
NS IPv6 target/s (XX::XX form): 2022::1, 2022::2

Fixes: 4e24be01 ("bonding: add new parameter ns_targets")
Reported-by: Li Liang <liali@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20220530062639.37179-1-liuhangbin@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Before 7beecaf7 ("net: phy: at803x: improve the WOL feature") patch
"at803x_get_wol" implementation used AT803X_INTR_ENABLE_WOL value to set
WAKE_MAGIC flag, and now AT803X_WOL_EN value is used for the same purpose.
The problem here is that the values of these two bits are different after
hardware reset: AT803X_INTR_ENABLE_WOL=0 after hardware reset, but
AT803X_WOL_EN=1. So now, if called right after boot, "at803x_get_wol" will
set WAKE_MAGIC flag, even if WOL function is not enabled by calling
"at803x_set_wol" function. The patch disables WOL function on probe thus
the behavior is consistent.

Fixes: 7beecaf7 ("net: phy: at803x: improve the WOL feature")
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Link: https://lore.kernel.org/r/20220527084935.235274-1-viorel.suman@oss.nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fix the following build warning when CONFIG_IPV6 is not set:

In function ‘fortify_memcpy_chk’,
    inlined from ‘tcp_md5_do_add’ at net/ipv4/tcp_ipv4.c:1210:2:
./include/linux/fortify-string.h:328:4: error: call to ‘__write_overflow_field’ declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
  328 |    __write_overflow_field(p_size_field, size);
      |    ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: huhai <huhai@kylinos.cn>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220526101213.2392980-1-zhanggenjian@kylinos.cnSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The set_tim is supposed to be atomic, but we should download beacon
context to firmware with a mutex lock. To avoid warning, do the thing in
another work.

BUG: scheduling while atomic: swapper/1/0/0x00000700
Modules linked in:
CPU: 1 PID: 0 Comm: swapper/1 Tainted: G        W         5.18.0-rc7-00703-g33b5ee09a0c1 #4
Hardware name: Pine64 RK3566 Quartz64-A Board (DT)
Call trace:
 dump_backtrace.part.0+0xc4/0xd0
 show_stack+0x14/0x60
 dump_stack_lvl+0x60/0x78
 dump_stack+0x14/0x2c
 __schedule_bug+0x5c/0x70
 __schedule+0x5c4/0x630
 schedule+0x44/0xb0
 schedule_preempt_disabled+0xc/0x14
 __mutex_lock.constprop.0+0x538/0x56c
 __mutex_lock_slowpath+0x10/0x20
 mutex_lock+0x54/0x60
 rtw_ops_set_tim+0x20/0x40
 __sta_info_recalc_tim+0x150/0x250
 sta_info_recalc_tim+0x10/0x20
 invoke_tx_handlers_early+0x4e4/0x5c0
 ieee80211_tx+0x78/0x110
 ieee80211_xmit+0x94/0xc0
 __ieee80211_subif_start_xmit+0x818/0xd20
 ieee80211_subif_start_xmit+0x44/0x2d0
 dev_hard_start_xmit+0xd0/0x150
 __dev_queue_xmit+0x250/0xb30
 dev_queue_xmit+0x10/0x20
 br_dev_queue_push_xmit+0x94/0x174
 br_forward_finish+0x90/0xa0
 __br_forward+0xc0/0x13c
 br_forward+0x108/0x134
 br_dev_xmit+0x1cc/0x3a4
 dev_hard_start_xmit+0xd0/0x150
 __dev_queue_xmit+0x250/0xb30
 dev_queue_xmit+0x10/0x20
 arp_xmit+0x6c/0x7c
 arp_send_dst+0x8c/0xc0
 arp_solicit+0xd4/0x1e0
 neigh_probe+0x58/0xa0
 neigh_timer_handler+0x27c/0x380
 call_timer_fn.constprop.0+0x20/0x80
 __run_timers.part.0+0x230/0x280
 run_timer_softirq+0x38/0x70
 _stext+0x104/0x278
 __irq_exit_rcu+0xa4/0xdc
 irq_exit_rcu+0xc/0x14
 el1_interrupt+0x34/0x50
 el1h_64_irq_handler+0x14/0x20
 el1h_64_irq+0x64/0x68
 arch_cpu_idle+0x14/0x20
 do_idle+0x208/0x290
 cpu_startup_entry+0x20/0x30
 secondary_start_kernel+0x130/0x144
 __secondary_switched+0x54/0x58

Fixes: f2217968 ("rtw88: Add update beacon flow for AP mode")
Reported-by: Ondřej Jirman <megi@xff.cz>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Ondřej Jirman <megi@xff.cz>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220526051251.281905-1-pkshih@realtek.com

At least mips64 has ist own CAUSE macro, so rename ours to
IWL_CAUSE to fix build issues.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Fixes: c1918196 ("iwlwifi: pcie: simplify MSI-X cause mapping")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220523220300.682be2029361.I283200b18da589a975a284073dca8ed001ee107a@changeid

The firmware has a 512 limit here, but we use less, so gcc
starts complaining about it:

drivers/net/wireless/marvell/libertas/cfg.c:1198:63: warning: array subscript ‘struct cmd_ds_802_11_associate_response[0]’ is partly outside array bounds of ‘unsigned char[203]’ [-Warray-bounds]
 1198 |                       "aid 0x%04x\n", status, le16_to_cpu(resp->statuscode),
      |                                                               ^~

Since we size the command and response buffer per our needs
and not per the firmware maximum, change to a variable size
data array and put the 512 only into a comment.

In the end, that's actually what the code always wanted, and
it simplifies the code that used to subtract the fixed size
buffer size in two places.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220523180200.115fa27fbece.Ie66d874b047e7afad63900aa2df70f031711147e@changeid

Íñigo Huguet says:

====================
sfc: fix some efx_separate_tx_channels errors

Trying to load sfc driver with modparam efx_separate_tx_channels=1
resulted in errors during initialization and not being able to use the
NIC. This patches fix a few bugs and make it work again.

v2:
* added Martin's patch instead of a previous mine. Mine one solved some
of the initialization errors, but Martin's solves them also in all
possible cases.
* removed whitespaces cleanup, as requested by Jakub
====================
Signed-off-by: David S. Miller <davem@davemloft.net>