- 13 Mar, 2019 40 commits
-
-
James Morse authored
[ Upstream commit f2b3d856 ] On systems with VHE the kernel and KVM's world-switch code run at the same exception level. Code that is only used on a VHE system does not need to be annotated as __hyp_text as it can reside anywhere in the kernel text. __hyp_text was also used to prevent kprobes from patching breakpoint instructions into this region, as this code runs at a different exception level. While this is no longer true with VHE, KVM still switches VBAR_EL1, meaning a kprobe's breakpoint executed in the world-switch code will cause a hyp-panic. Move the __hyp_text check in the kprobes blacklist so it applies on VHE systems too, to cover the common code and guest enter/exit assembly. Fixes: 888b3c87 ("arm64: Treat all entry code as non-kprobe-able") Reviewed-by:
Christoffer Dall <christoffer.dall@arm.com> Signed-off-by:
James Morse <james.morse@arm.com> Acked-by:
Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Thomas Lendacky authored
[ Upstream commit 912139cf ] The load_microcode_amd() function searches for microcode patches and attempts to apply a microcode patch if it is of different level than the currently installed level. While the processor won't actually load a level that is less than what is already installed, the logic wrongly returns UCODE_NEW thus signaling to its caller reload_store() that a late loading should be attempted. If the file-system contains an older microcode revision than what is currently running, such a late microcode reload can result in these misleading messages: x86/CPU: CPU features have changed after loading microcode, but might not take effect. x86/CPU: Please consider either early loading through initrd/built-in or a potential BIOS update. These messages were issued on a system where SME/SEV are not enabled by the BIOS (MSR C001_0010[23] = 0b) because during boot, early_detect_mem_encrypt() is called and cleared the SME and SEV features in this case. However, after the wrong late load attempt, get_cpu_cap() is called and reloads the SME and SEV feature bits, resulting in the messages. Update the microcode level check to not attempt microcode loading if the current level is greater than(!) and not only equal to the current patch level. [ bp: massage commit message. ] Fixes: 2613f36e ("x86/microcode: Attempt late loading only when new microcode is present") Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/154894518427.9406.8246222496874202773.stgit@tlendack-t1.amdoffice.netSigned-off-by:
-
Ronnie Sahlberg authored
[ Upstream commit 58d15ed1 ] The size of the fixed part of the create response is 88 bytes not 56. Signed-off-by:
Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by:
Steve French <stfrench@microsoft.com> Reviewed-by:
Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by:
-
Sinan Kaya authored
[ Upstream commit 0ee4b5f8 ] Add BACKLIGHT_LCD_SUPPORT for SAMSUNG_Q10 to fix the warning: unmet direct dependencies detected for BACKLIGHT_CLASS_DEVICE. SAMSUNG_Q10 selects BACKLIGHT_CLASS_DEVICE but BACKLIGHT_CLASS_DEVICE depends on BACKLIGHT_LCD_SUPPORT. Copy BACKLIGHT_LCD_SUPPORT dependency into SAMSUNG_Q10 to fix: WARNING: unmet direct dependencies detected for BACKLIGHT_CLASS_DEVICE Depends on [n]: HAS_IOMEM [=y] && BACKLIGHT_LCD_SUPPORT [=n] Selected by [y]: - SAMSUNG_Q10 [=y] && X86 [=y] && X86_PLATFORM_DEVICES [=y] && ACPI [=y] Signed-off-by:
Sinan Kaya <okaya@kernel.org> Acked-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit 8437fcf1 ] The "hostdata->dev" pointer is NULL here. We set "hostdata->dev = dev;" later in the function and we also use "hostdata->dev" when we call dma_free_attrs() in NCR_700_release(). This bug predates git version control. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Ming Lu authored
[ Upstream commit 5d8fc4a9 ] The issue to be fixed in this commit is when libfc found it received a invalid FLOGI response from FC switch, it would return without freeing the fc frame, which is just the skb data. This would cause memory leak if FC switch keeps sending invalid FLOGI responses. This fix is just to make it execute `fc_frame_free(fp)` before returning from function `fc_lport_flogi_resp`. Signed-off-by:
Ming Lu <ming.lu@citrix.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
-
Manish Chopra authored
[ Upstream commit ffb057f9 ] KASAN reported following bug in qed_init_qm_get_idx_from_flags due to inappropriate casting of "pq_flags". Fix the type of "pq_flags". [ 196.624707] BUG: KASAN: stack-out-of-bounds in qed_init_qm_get_idx_from_flags+0x1a4/0x1b8 [qed] [ 196.624712] Read of size 8 at addr ffff809b00bc7360 by task kworker/0:9/1712 [ 196.624714] [ 196.624720] CPU: 0 PID: 1712 Comm: kworker/0:9 Not tainted 4.18.0-60.el8.aarch64+debug #1 [ 196.624723] Hardware name: To be filled by O.E.M. Saber/Saber, BIOS 0ACKL024 09/26/2018 [ 196.624733] Workqueue: events work_for_cpu_fn [ 196.624738] Call trace: [ 196.624742] dump_backtrace+0x0/0x2f8 [ 196.624745] show_stack+0x24/0x30 [ 196.624749] dump_stack+0xe0/0x11c [ 196.624755] print_address_description+0x68/0x260 [ 196.624759] kasan_report+0x178/0x340 [ 196.624762] __asan_report_load_n_noabort+0x38/0x48 [ 196.624786] qed_init_qm_get_idx_from_flags+0x1a4/0x1b8 [qed] [ 196.624808] qed_init_qm_info+0xec0/0x2200 [qed] [ 196.624830] qed_resc_alloc+0x284/0x7e8 [qed] [ 196.624853] qed_slowpath_start+0x6cc/0x1ae8 [qed] [ 196.624864] __qede_probe.isra.10+0x1cc/0x12c0 [qede] [ 196.624874] qede_probe+0x78/0xf0 [qede] [ 196.624879] local_pci_probe+0xc4/0x180 [ 196.624882] work_for_cpu_fn+0x54/0x98 [ 196.624885] process_one_work+0x758/0x1900 [ 196.624888] worker_thread+0x4e0/0xd18 [ 196.624892] kthread+0x2c8/0x350 [ 196.624897] ret_from_fork+0x10/0x18 [ 196.624899] [ 196.624902] Allocated by task 2: [ 196.624906] kasan_kmalloc.part.1+0x40/0x108 [ 196.624909] kasan_kmalloc+0xb4/0xc8 [ 196.624913] kasan_slab_alloc+0x14/0x20 [ 196.624916] kmem_cache_alloc_node+0x1dc/0x480 [ 196.624921] copy_process.isra.1.part.2+0x1d8/0x4a98 [ 196.624924] _do_fork+0x150/0xfa0 [ 196.624926] kernel_thread+0x48/0x58 [ 196.624930] kthreadd+0x3a4/0x5a0 [ 196.624932] ret_from_fork+0x10/0x18 [ 196.624934] [ 196.624937] Freed by task 0: [ 196.624938] (stack is not available) [ 196.624940] [ 196.624943] The buggy address belongs to the object at ffff809b00bc0000 [ 196.624943] which belongs to the cache thread_stack of size 32768 [ 196.624946] The buggy address is located 29536 bytes inside of [ 196.624946] 32768-byte region [ffff809b00bc0000, ffff809b00bc8000) [ 196.624948] The buggy address belongs to the page: [ 196.624952] page:ffff7fe026c02e00 count:1 mapcount:0 mapping:ffff809b4001c000 index:0x0 compound_mapcount: 0 [ 196.624960] flags: 0xfffff8000008100(slab|head) [ 196.624967] raw: 0fffff8000008100 dead000000000100 dead000000000200 ffff809b4001c000 [ 196.624970] raw: 0000000000000000 0000000000080008 00000001ffffffff 0000000000000000 [ 196.624973] page dumped because: kasan: bad access detected [ 196.624974] [ 196.624976] Memory state around the buggy address: [ 196.624980] ffff809b00bc7200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 196.624983] ffff809b00bc7280: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 196.624985] >ffff809b00bc7300: 00 00 00 00 00 00 00 00 f1 f1 f1 f1 04 f2 f2 f2 [ 196.624988] ^ [ 196.624990] ffff809b00bc7380: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 196.624993] ffff809b00bc7400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 196.624995] ================================================================== Signed-off-by:
Manish Chopra <manishc@marvell.com> Signed-off-by:
Ariel Elior <aelior@marvell.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Manish Chopra authored
[ Upstream commit 7c81626a ] Cache number of fragments in the skb locally as in case of linear skb (with zero fragments), tx completion (or freeing of skb) may happen before driver tries to get number of frgaments from the skb which could lead to stale access to an already freed skb. Signed-off-by:
-
Manish Chopra authored
[ Upstream commit 327852ec ] VFs may hit VF-PF channel timeout while probing, as in some cases it was observed that VF FLR and VF "acquire" message transaction (i.e first message from VF to PF in VF's probe flow) could occur simultaneously which could lead VF to fail sending "acquire" message to PF as VF is marked disabled from HW perspective due to FLR, which will result into channel timeout and VF probe failure. In such cases, try retrying VF "acquire" message so that in later attempts it could be successful to pass message to PF after the VF FLR is completed and can be probed successfully. Signed-off-by:
-
Manish Chopra authored
[ Upstream commit ff929696 ] VF is always configured to drop control frames (with reserved mac addresses) but to work LACP on the VFs, it would require LACP control frames to be forwarded or transmitted successfully. This patch fixes this in such a way that trusted VFs (marked through ndo_set_vf_trust) would be allowed to pass the control frames such as LACP pdus. Signed-off-by:
-
Manish Chopra authored
[ Upstream commit 9e71a15d ] When running tx switched traffic between VNICs created via a bridge(to which VFs are added), adapter drops the unicast packets in tx flow due to VNIC's ucast mac being unknown to it. But VF interfaces being in promiscuous mode should have caused adapter to accept all the unknown ucast packets. Later, it was found that driver doesn't really configure tx promiscuous mode settings to accept all unknown unicast macs. This patch fixes tx promiscuous mode settings to accept all unknown/unmatched unicast macs and works out the scenario. Signed-off-by:
-
Yao Liu authored
[ Upstream commit 80ff0017 ] There is a NULL pointer dereference of dev_name in nfs_parse_devname() The oops looks something like: BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 ... RIP: 0010:nfs_fs_mount+0x3b6/0xc20 [nfs] ... Call Trace: ? ida_alloc_range+0x34b/0x3d0 ? nfs_clone_super+0x80/0x80 [nfs] ? nfs_free_parsed_mount_data+0x60/0x60 [nfs] mount_fs+0x52/0x170 ? __init_waitqueue_head+0x3b/0x50 vfs_kern_mount+0x6b/0x170 do_mount+0x216/0xdc0 ksys_mount+0x83/0xd0 __x64_sys_mount+0x25/0x30 do_syscall_64+0x65/0x220 entry_SYSCALL_64_after_hwframe+0x49/0xbe Fix this by adding a NULL check on dev_name Signed-off-by:
Yao Liu <yotta.liu@ucloud.cn> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
Fathi Boudra authored
[ Upstream commit 7d4e591b ] posix_timers fails to build due to undefined reference errors: aarch64-linaro-linux-gcc --sysroot=/build/tmp-rpb-glibc/sysroots/hikey -O2 -pipe -g -feliminate-unused-debug-types -O3 -Wl,-no-as-needed -Wall -DKTEST -Wl,-O1 -Wl,--hash-style=gnu -Wl,--as-needed -lrt -lpthread posix_timers.c -o /build/tmp-rpb-glibc/work/hikey-linaro-linux/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/timers/posix_timers /tmp/cc1FTZzT.o: In function `check_timer_create': /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/timers/posix_timers.c:157: undefined reference to `timer_create' /usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/timers/posix_timers.c:170: undefined reference to `timer_settime' collect2: error: ld returned 1 exit status It's GNU Make and linker specific. The default Makefile rule looks like: $(CC) $(CFLAGS) $(LDFLAGS) $@ $^ $(LDLIBS) When linking is done by gcc itself, no issue, but when it needs to be passed to proper ld, only LDLIBS follows and then ld cannot know what libs to link with. More detail: https://www.gnu.org/software/make/manual/html_node/Implicit-Variables.html LDFLAGS Extra flags to give to compilers when they are supposed to invoke the linker, ‘ld’, such as -L. Libraries (-lfoo) should be added to the LDLIBS variable instead. LDLIBS Library flags or names given to compilers when they are supposed to invoke the linker, ‘ld’. LOADLIBES is a deprecated (but still supported) alternative to LDLIBS. Non-library linker flags, such as -L, should go in the LDFLAGS variable. https://lkml.org/lkml/2010/2/10/362 tools/perf: libraries must come after objects Link order matters, use LDLIBS instead of LDFLAGS to properly link against libpthread. Signed-off-by:
Denys Dmytriyenko <denys@ti.com> Signed-off-by:
Fathi Boudra <fathi.boudra@linaro.org> Signed-off-by:
Shuah Khan <shuah@kernel.org> Signed-off-by:
-
Andrew Lunn authored
[ Upstream commit 7ae710f9 ] On SoC reset all GPIO interrupts are disable. However, if kexec is used to boot into a new kernel, the SoC does not experience a reset. Hence GPIO interrupts can be left enabled from the previous kernel. It is then possible for the interrupt to fire before an interrupt handler is registered, resulting in the kernel complaining of an "unexpected IRQ trap", the interrupt is never cleared, and so fires again, resulting in an interrupt storm. Disable all GPIO interrupts before registering the GPIO IRQ chip. Fixes: 7f2691a1 ("gpio: vf610: add gpiolib/IRQ chip driver for Vybrid") Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Acked-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Florian Westphal authored
[ Upstream commit 2035f3ff ] Unlike ip(6)tables ebtables only counts user-defined chains. The effect is that a 32bit ebtables binary on a 64bit kernel can do 'ebtables -N FOO' only after adding at least one rule, else the request fails with -EINVAL. This is a similar fix as done in 3f1e53ab ("netfilter: ebtables: don't attempt to allocate 0-sized compat array"). Fixes: 7d7d7e02 ("netfilter: compat: reject huge allocation requests") Reported-by:
Francesco Ruggeri <fruggeri@arista.com> Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Alexey Khoroshilov authored
[ Upstream commit c69c29a1 ] If phy_power_on() fails in rk_gmac_powerup(), clocks are left enabled. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
-
Yonglong Liu authored
[ Upstream commit cec8abba ] When reading phy registers via Clause 45 MDIO protocol, after write address operation, the driver use another write address operation, so can not read the right value of any phy registers. This patch fixes it. Signed-off-by:
Yonglong Liu <liuyonglong@huawei.com> Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
-
Yonglong Liu authored
[ Upstream commit ed29ca8b ] The hns driver of earlier devices, when autoneg off, restart autoneg will return -EINVAL, so make the hns driver for the latest devices do the same. Signed-off-by:
-
Yonglong Liu authored
[ Upstream commit 263c6d75 ] In hns enet driver, we use of_parse_handle() to get hold of the device node related to "ae-handle" but we have missed to put the node reference using of_node_put() after we are done using the node. This patch fixes it. Note: This problem is stated in Link: https://lkml.org/lkml/2018/12/22/217 Fixes: 48189d6a ("net: hns: enet specifies a reference to dsaf") Reported-by:
-
Tomonori Sakita authored
[ Upstream commit 6571ebce ] If fill_level was not zero and status was not BUSY, result of "tx_prod - tx_cons - inuse" might be zero. Subtracting 1 unconditionally results invalid negative return value on this case. Make sure not to return an negative value. Signed-off-by:
Tomonori Sakita <tomonori.sakita@sord.co.jp> Signed-off-by:
Atsushi Nemoto <atsushi.nemoto@sord.co.jp> Reviewed-by:
Dalon L Westergreen <dalon.westergreen@linux.intel.com> Acked-by:
Thor Thayer <thor.thayer@linux.intel.com> Signed-off-by:
-
Max Filippov authored
[ Upstream commit 25384ce5 ] This fixes the following warning at boot when the kernel is booted on a board with more CPU cores than was configured in NR_CPUS: smp_init_cpus: Core Count = 8 smp_init_cpus: Core Id = 0 ------------[ cut here ]------------ WARNING: CPU: 0 PID: 0 at include/linux/cpumask.h:121 smp_init_cpus+0x54/0x74 Modules linked in: CPU: 0 PID: 0 Comm: swapper Not tainted 5.0.0-rc3-00015-g1459333f88a0 #124 Call Trace: __warn$part$3+0x6a/0x7c warn_slowpath_null+0x35/0x3c smp_init_cpus+0x54/0x74 setup_arch+0x1c0/0x1d0 start_kernel+0x44/0x310 _startup+0x107/0x107 Signed-off-by:
Max Filippov <jcmvbkbc@gmail.com> Signed-off-by:
-
Max Filippov authored
[ Upstream commit 8b1c42cd ] Otherwise it is impossible to enable CPUs after booting with 'maxcpus' parameter. Signed-off-by:
-
Max Filippov authored
[ Upstream commit 306b3830 ] Secondary CPU reset vector overlaps part of the double exception handler code, resulting in weird crashes and hangups when running user code. Move exception vectors one page up so that they don't clash with the secondary CPU reset vector. Signed-off-by:
-
Max Filippov authored
[ Upstream commit 32a7726c ] - add missing memory barriers to the secondary CPU synchronization spin loops; add comment to the matching memory barrier in the boot_secondary and __cpu_die functions; - use READ_ONCE/WRITE_ONCE to access cpu_start_id/cpu_start_ccount instead of reading/writing them directly; - re-initialize cpu_running every time before starting secondary CPU to flush possible previous CPU startup results. Signed-off-by:
-
Colin Ian King authored
[ Upstream commit 2b531b61 ] The cpu-hotplug test assumes that we can offline the maximum CPU as described by /sys/devices/system/cpu/offline. However, in the case where the number of CPUs exceeds like kernel configuration then the offline count can be greater than the present count and we end up trying to test the offlining of a CPU that is not available to offline. Fix this by testing the maximum present CPU instead. Also, the test currently offlines the CPU and does not online it, so fix this by onlining the CPU after the test. Fixes: d89dffa9 ("fault-injection: add selftests for cpu and memory hotplug") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Max Filippov authored
[ Upstream commit 4fe8713b ] ccount_timer_shutdown is called from the atomic context in the secondary_start_kernel, resulting in the following BUG: BUG: sleeping function called from invalid context in_atomic(): 1, irqs_disabled(): 1, pid: 0, name: swapper/1 Preemption disabled at: secondary_start_kernel+0xa1/0x130 Call Trace: ___might_sleep+0xe7/0xfc __might_sleep+0x41/0x44 synchronize_irq+0x24/0x64 disable_irq+0x11/0x14 ccount_timer_shutdown+0x12/0x20 clockevents_switch_state+0x82/0xb4 clockevents_exchange_device+0x54/0x60 tick_check_new_device+0x46/0x70 clockevents_register_device+0x8c/0xc8 clockevents_config_and_register+0x1d/0x2c local_timer_setup+0x75/0x7c secondary_start_kernel+0xb4/0x130 should_never_return+0x32/0x35 Use disable_irq_nosync instead of disable_irq to avoid it. This is safe because the ccount timer IRQ is per-CPU, and once IRQ is masked the ISR will not be called. Signed-off-by:
-
Suravee Suthikulpanit authored
[ Upstream commit 9825bd94 ] When a VM is terminated, the VFIO driver detaches all pass-through devices from VFIO domain by clearing domain id and page table root pointer from each device table entry (DTE), and then invalidates the DTE. Then, the VFIO driver unmap pages and invalidate IOMMU pages. Currently, the IOMMU driver keeps track of which IOMMU and how many devices are attached to the domain. When invalidate IOMMU pages, the driver checks if the IOMMU is still attached to the domain before issuing the invalidate page command. However, since VFIO has already detached all devices from the domain, the subsequent INVALIDATE_IOMMU_PAGES commands are being skipped as there is no IOMMU attached to the domain. This results in data corruption and could cause the PCI device to end up in indeterministic state. Fix this by invalidate IOMMU pages when detach a device, and before decrementing the per-domain device reference counts. Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Suggested-by:
Joerg Roedel <joro@8bytes.org> Co-developed-by:
Brijesh Singh <brijesh.singh@amd.com> Signed-off-by:
Suravee Suthikulpanit <suravee.suthikulpanit@amd.com> Fixes: 6de8ad9b ('x86/amd-iommu: Make iommu_flush_pages aware of multiple IOMMUs') Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
ZhangXiaoxu authored
[ Upstream commit 53ab60ba ] There is a UBSAN bug report as below: UBSAN: Undefined behaviour in net/netfilter/ipvs/ip_vs_ctl.c:2227:21 signed integer overflow: -2147483647 * 1000 cannot be represented in type 'int' Reproduce program: #include <stdio.h> #include <sys/types.h> #include <sys/socket.h> #define IPPROTO_IP 0 #define IPPROTO_RAW 255 #define IP_VS_BASE_CTL (64+1024+64) #define IP_VS_SO_SET_TIMEOUT (IP_VS_BASE_CTL+10) /* The argument to IP_VS_SO_GET_TIMEOUT */ struct ipvs_timeout_t { int tcp_timeout; int tcp_fin_timeout; int udp_timeout; }; int main() { int ret = -1; int sockfd = -1; struct ipvs_timeout_t to; sockfd = socket(AF_INET, SOCK_RAW, IPPROTO_RAW); if (sockfd == -1) { printf("socket init error\n"); return -1; } to.tcp_timeout = -2147483647; to.tcp_fin_timeout = -2147483647; to.udp_timeout = -2147483647; ret = setsockopt(sockfd, IPPROTO_IP, IP_VS_SO_SET_TIMEOUT, (char *)(&to), sizeof(to)); printf("setsockopt return %d\n", ret); return ret; } Return -EINVAL if the timeout value is negative or max than 'INT_MAX / HZ'. Signed-off-by:
ZhangXiaoxu <zhangxiaoxu5@huawei.com> Acked-by:
Simon Horman <horms@verge.net.au> Signed-off-by:
-
Jerry Snitselaar authored
[ Upstream commit f1724c08 ] In the error path of map_sg there is an incorrect if condition for breaking out of the loop that searches the scatterlist for mapped pages to unmap. Instead of breaking out of the loop once all the pages that were mapped have been unmapped, it will break out of the loop after it has unmapped 1 page. Fix the condition, so it breaks out of the loop only after all the mapped pages have been unmapped. Fixes: 80187fd3 ("iommu/amd: Optimize map_sg and unmap_sg") Cc: Joerg Roedel <joro@8bytes.org> Signed-off-by:
Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by:
-
Jerry Snitselaar authored
[ Upstream commit 51d8838d ] In the error path of map_sg, free_iova_fast is being called with address instead of the pfn. This results in a bad value getting into the rcache, and can result in hitting a BUG_ON when iova_magazine_free_pfns is called. Cc: Joerg Roedel <joro@8bytes.org> Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com> Signed-off-by:
-
Brian Welty authored
[ Upstream commit 904bba21 ] The work completion length for a receiving a UD send with immediate is short by 4 bytes causing application using this opcode to fail. The UD receive logic incorrectly subtracts 4 bytes for immediate value. These bytes are already included in header length and are used to calculate header/payload split, so the result is these 4 bytes are subtracted twice, once when the header length subtracted from the overall length and once again in the UD opcode specific path. Remove the extra subtraction when handling the opcode. Fixes: 77241056 ("IB/hfi1: add driver files") Reviewed-by:
Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by:
Brian Welty <brian.welty@intel.com> Signed-off-by:
Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by:
Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by:
Jason Gunthorpe <jgg@mellanox.com> Signed-off-by:
-
Stephane Eranian authored
[ Upstream commit 1497e804 ] This patch fixes an issue in cpumap.c when used with the TOPOLOGY header. In some configurations, some NUMA nodes may have no CPU (empty cpulist). Yet a cpumap map must be created otherwise perf abort with an error. This patch handles this case by creating a dummy map. Before: $ perf record -o - -e cycles noploop 2 | perf script -i - 0x6e8 [0x6c]: failed to process type: 80 After: $ perf record -o - -e cycles noploop 2 | perf script -i - noploop for 2 seconds Signed-off-by:
Stephane Eranian <eranian@google.com> Acked-by:
Jiri Olsa <jolsa@kernel.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1547885559-1657-1-git-send-email-eranian@google.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Stephane Eranian authored
[ Upstream commit 1a51c5da ] The perf_proc_update_handler() handles /proc/sys/kernel/perf_event_max_sample_rate syctl variable. When the PMU IRQ handler timing monitoring is disabled, i.e, when /proc/sys/kernel/perf_cpu_time_max_percent is equal to 0 or 100, then no modification to sysctl_perf_event_sample_rate is allowed to prevent possible hang from wrong values. The problem is that the test to prevent modification is made after the sysctl variable is modified in perf_proc_update_handler(). You get an error: $ echo 10001 >/proc/sys/kernel/perf_event_max_sample_rate echo: write error: invalid argument But the value is still modified causing all sorts of inconsistencies: $ cat /proc/sys/kernel/perf_event_max_sample_rate 10001 This patch fixes the problem by moving the parsing of the value after the test. Committer testing: # echo 100 > /proc/sys/kernel/perf_cpu_time_max_percent # echo 10001 > /proc/sys/kernel/perf_event_max_sample_rate -bash: echo: write error: Invalid argument # cat /proc/sys/kernel/perf_event_max_sample_rate 10001 # Signed-off-by:
Andi Kleen <ak@linux.intel.com> Reviewed-by:
-
Su Yanjun authored
[ Upstream commit dd9ee344 ] Recently we run a network test over ipcomp virtual tunnel.We find that if a ipv4 packet needs fragment, then the peer can't receive it. We deep into the code and find that when packet need fragment the smaller fragment will be encapsulated by ipip not ipcomp. So when the ipip packet goes into xfrm, it's skb->dev is not properly set. The ipv4 reassembly code always set skb'dev to the last fragment's dev. After ipv4 defrag processing, when the kernel rp_filter parameter is set, the skb will be drop by -EXDEV error. This patch adds compatible support for the ipip process in ipcomp virtual tunnel. Signed-off-by:
Su Yanjun <suyj.fnst@cn.fujitsu.com> Signed-off-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
-
Alistair Strachan authored
commit 47bb1179 upstream. When initially testing the Camera Terminal Descriptor wTerminalType field (buffer[4]), no mask is used. Later in the function, the MSB is overloaded to store the descriptor subtype, and so a mask of 0x7fff is used to check the type. If a descriptor is specially crafted to set this overloaded bit in the original wTerminalType field, the initial type check will fail (falling through, without adjusting the buffer size), but the later type checks will pass, assuming the buffer has been made suitably large, causing an overflow. Avoid this problem by checking for the MSB in the wTerminalType field. If the bit is set, assume the descriptor is bad, and abort parsing it. Originally reported here: https://groups.google.com/forum/#!topic/syzkaller/Ot1fOE6v1d8 A similar (non-compiling) patch was provided at that time. Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
Alistair Strachan <astrachan@google.com> Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Martin Wilck authored
commit 4a067cf8 upstream. Up to 4.12, __scsi_error_from_host_byte() would reset the host byte to DID_OK for various cases including DID_NEXUS_FAILURE. Commit 2a842aca ("block: introduce new block status code type") replaced this function with scsi_result_to_blk_status() and removed the host-byte resetting code for the DID_NEXUS_FAILURE case. As the line set_host_byte(cmd, DID_OK) was preserved for the other cases, I suppose this was an editing mistake. The fact that the host byte remains set after 4.13 is causing problems with the sg_persist tool, which now returns success rather then exit status 24 when a RESERVATION CONFLICT error is encountered. Fixes: 2a842aca "block: introduce new block status code type" Signed-off-by:
Martin Wilck <mwilck@suse.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
YueHaibing authored
commit f612acfa upstream. syzkaller report this: BUG: memory leak unreferenced object 0xffffc9000488d000 (size 9195520): comm "syz-executor.0", pid 2752, jiffies 4294787496 (age 18.757s) hex dump (first 32 bytes): ff ff ff ff ff ff ff ff a8 00 00 00 01 00 00 00 ................ 02 00 00 00 00 00 00 00 80 a1 7a c1 ff ff ff ff ..........z..... backtrace: [<000000000863775c>] __vmalloc_node mm/vmalloc.c:1795 [inline] [<000000000863775c>] __vmalloc_node_flags mm/vmalloc.c:1809 [inline] [<000000000863775c>] vmalloc+0x8c/0xb0 mm/vmalloc.c:1831 [<000000003f668111>] kernel_read_file+0x58f/0x7d0 fs/exec.c:924 [<000000002385813f>] kernel_read_file_from_fd+0x49/0x80 fs/exec.c:993 [<0000000011953ff1>] __do_sys_finit_module+0x13b/0x2a0 kernel/module.c:3895 [<000000006f58491f>] do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290 [<00000000ee78baf4>] entry_SYSCALL_64_after_hwframe+0x49/0xbe [<00000000241f889b>] 0xffffffffffffffff It should goto 'out_free' lable to free allocated buf while kernel_read fails. Fixes: 39d637af ("vfs: forbid write access when reading a file into memory") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Cc: Thibaut Sautereau <thibaut@sautereau.fr> Signed-off-by:
-
Matthias Kaehlcke authored
commit c4f5627f upstream. With commit e1633762 ("Bluetooth: Handle bt_accept_enqueue() socket atomically") lock_sock[_nested]() is used to acquire the socket lock before manipulating the socket. lock_sock[_nested]() may block, which is problematic since bt_accept_enqueue() can be called in bottom half context (e.g. from rfcomm_connect_ind()): [<ffffff80080d81ec>] __might_sleep+0x4c/0x80 [<ffffff800876c7b0>] lock_sock_nested+0x24/0x58 [<ffffff8000d7c27c>] bt_accept_enqueue+0x48/0xd4 [bluetooth] [<ffffff8000e67d8c>] rfcomm_connect_ind+0x190/0x218 [rfcomm] Add a parameter to bt_accept_enqueue() to indicate whether the function is called from BH context, and acquire the socket lock with bh_lock_sock_nested() if that's the case. Also adapt all callers of bt_accept_enqueue() to pass the new parameter: - l2cap_sock_new_connection_cb() - uses lock_sock() to lock the parent socket => process context - rfcomm_connect_ind() - acquires the parent socket lock with bh_lock_sock() => BH context - __sco_chan_add() - called from sco_chan_add(), which is called from sco_connect(). parent is NULL, hence bt_accept_enqueue() isn't called in this code path and we can ignore it - also called from sco_conn_ready(). uses bh_lock_sock() to acquire the parent lock => BH context Fixes: e1633762 ("Bluetooth: Handle bt_accept_enqueue() socket atomically") Signed-off-by:
Matthias Kaehlcke <mka@chromium.org> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org Signed-off-by:
-
Max Filippov authored
commit d90b88fd upstream. Stack unwinding is implemented incorrectly in xtensa get_wchan: instead of extracting a0 and a1 registers from the spill location under the stack pointer it extracts a word pointed to by the stack pointer and subtracts 4 or 3 from it. Cc: stable@vger.kernel.org Signed-off-by:
-
Mike Kravetz authored
commit cb6acd01 upstream. hugetlb pages should only be migrated if they are 'active'. The routines set/clear_page_huge_active() modify the active state of hugetlb pages. When a new hugetlb page is allocated at fault time, set_page_huge_active is called before the page is locked. Therefore, another thread could race and migrate the page while it is being added to page table by the fault code. This race is somewhat hard to trigger, but can be seen by strategically adding udelay to simulate worst case scheduling behavior. Depending on 'how' the code races, various BUG()s could be triggered. To address this issue, simply delay the set_page_huge_active call until after the page is successfully added to the page table. Hugetlb pages can also be leaked at migration time if the pages are associated with a file in an explicitly mounted hugetlbfs filesystem. For example, consider a two node system with 4GB worth of huge pages available. A program mmaps a 2G file in a hugetlbfs filesystem. It then migrates the pages associated with the file from one node to another. When the program exits, huge page counts are as follows: node0 1024 free_hugepages 1024 nr_hugepages node1 0 free_hugepages 1024 nr_hugepages Filesystem Size Used Avail Use% Mounted on nodev 4.0G 2.0G 2.0G 50% /var/opt/hugepool That is as expected. 2G of huge pages are taken from the free_hugepages counts, and 2G is the size of the file in the explicitly mounted filesystem. If the file is then removed, the counts become: node0 1024 free_hugepages 1024 nr_hugepages node1 1024 free_hugepages 1024 nr_hugepages Filesystem Size Used Avail Use% Mounted on nodev 4.0G 2.0G 2.0G 50% /var/opt/hugepool Note that the filesystem still shows 2G of pages used, while there actually are no huge pages in use. The only way to 'fix' the filesystem accounting is to unmount the filesystem If a hugetlb page is associated with an explicitly mounted filesystem, this information in contained in the page_private field. At migration time, this information is not preserved. To fix, simply transfer page_private from old to new page at migration time if necessary. There is a related race with removing a huge page from a file and migration. When a huge page is removed from the pagecache, the page_mapping() field is cleared, yet page_private remains set until the page is actually freed by free_huge_page(). A page could be migrated while in this state. However, since page_mapping() is not set the hugetlbfs specific routine to transfer page_private is not called and we leak the page count in the filesystem. To fix that, check for this condition before migrating a huge page. If the condition is detected, return EBUSY for the page. Link: http://lkml.kernel.org/r/74510272-7319-7372-9ea6-ec914734c179@oracle.com Link: http://lkml.kernel.org/r/20190212221400.3512-1-mike.kravetz@oracle.com Fixes: bcc54222 ("mm: hugetlb: introduce page_huge_active") Signed-off-by:
Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by:
Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: <stable@vger.kernel.org> [mike.kravetz@oracle.com: v2] Link: http://lkml.kernel.org/r/7534d322-d782-8ac6-1c8d-a8dc380eb3ab@oracle.com [mike.kravetz@oracle.com: update comment and changelog] Link: http://lkml.kernel.org/r/420bcfd6-158b-38e4-98da-26d0cd85bd01@oracle.comSigned-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
