Check requested speed for a given transfer before setting
27MHz or 108Mhz sysclk on SoCs that support both. This way
for baud rates below 212Khz we can use 27Mhz clock.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Link: https://lore.kernel.org/r/20211124193353.32311-2-kdasu.kdev@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

The recent commit 3f076575 ("spi: deduplicate spi_match_id()
in __spi_register_driver()") inadvertently inverted a condition
that provokes a (harmless) warning:

  WARNING KERN SPI driver mtd_dataflash has no spi_device_id for atmel,at45

Restore logic to avoid such warning to be issued.

Fixes: 3f076575 ("spi: deduplicate spi_match_id() in __spi_register_driver()")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20211123170034.41253-1-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Some Device Trees don't use a real device name in the compatible string
for SPI devices nodes, abusing the fact that the spidev driver name is
used to match as a fallback when a SPI device ID table is not defined.

But since commit 6840615f ("spi: spidev: Add SPI ID table") a table
for SPI device IDs was added to the driver breaking the assumption that
these DTs were relying on.

There has been a warning message for some time since commit 956b200a
("spi: spidev: Warn loudly if instantiated from DT as "spidev""), making
quite clear that this case is not really supported by the spidev driver.

Since these devices won't match anyways after the mentioned commit, there
is no point to continue if an spidev compatible is used. Let's just make
the driver probe to fail early.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20211109225920.1158920-1-javierm@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

Since the commit 196b0e2c ("spi: pxa2xx: Remove if statement
that is always true in pump_transfers()") the ->read() and ->write()
methods in the struct driver_data are reconfigured for each transfer.
Hence no need to keep the intermediate state in the struct chip_data.

The same applies to n_bytes member of the same data structure.
Get rid of unneeded storage for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122200622.43305-1-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Currently the 16-bit mode is what being used in user space.
However assuming that is not fully correct. Instead we should
use the respective mask, i.e. SPI_MODE_USER_MASK, which
precisely defines what bits are available for user space apps.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122175245.84691-1-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

  /*
   * Fix multi-line comment style as in this short example. Pay attention
   * to the capitalization, period and starting line of the text.
   */

While at it, split the (supposedly short) description of couple of functions
to summary (short description) and (long) description.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122171721.61553-3-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

krealloc() as any other kernel memory allocation calls accepts GFP flags,
one of which is __GFP_ZERO. Hence, no need to call memset() explicitly on
the reallocated buffer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122171721.61553-2-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The lpspi on i.MX8ULP is derived from i.MX7ULP, it uses two
compatible strings, so update the comaptible string for i.MX8ULP.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211120113454.785997-4-peng.fan@oss.nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

The same logic is used in spi_match_id() and in the __spi_register_driver().
By switching the former from taking struct spi_device * to const char * as
the second parameter we may deduplicate the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211119173718.52938-1-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Some PL022 implementations provide a reset line to the silicon
IP block, add a device tree property for this.

Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211120011715.2630873-1-linus.walleij@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

This doc is fairly outdated and only uses legacy device instantiation
terminology. Let us update it and also mention the OF and ACPI device
tables, to make easier for users to figure out how should be defined.

Also, mention that devices bind could be done in user-space now using
the "driver_override" sysfs entry.
Suggested-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211119121139.2412761-1-javierm@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>:

This patch series adds RSPI driver and dt binding support to RZ/G2L SoC.

Commit b59c1224 ("spi: spi-geni-qcom: Add support for GPI dma")
added GPI support but also added unused defines, so remove them
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20211117133110.2682631-1-vkoul@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

"ret" variable is already declared in qspi_transfer_in() at the
beginning of function, drop redeclaring ret in the if block, fixing
below:

spi-rspi.c: In function ‘qspi_transfer_in’:
spi-rspi.c:838:7: warning: declaration of ‘ret’ shadows a previous local
  838 |   int ret = rspi_dma_transfer(rspi, NULL, &xfer->rx_sg);
      |       ^~~
spi-rspi.c:835:6: note: shadowed declaration is here
  835 |  int ret;

Fixes: db300838 ("spi: rspi: avoid uninitialized variable access")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211118031041.2312-4-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

On RZ/G2L SoC we need to explicitly deassert the reset line
for the device to work, use this opportunity to deassert/assert
reset line in spi-rspi driver.

This patch adds support to read the "resets" property (if available)
from DT and perform deassert/assert when required.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211118031041.2312-3-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add RSPI binding documentation for Renesas RZ/G2L SoC.

RSPI block is identical to one found on RZ/A, so no driver changes are
required. The fallback compatible string "renesas,rspi-rz" will be used
on RZ/G2L.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211118031041.2312-2-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

Change the debugfs directory name from hisi_spi65535 to hisi_spi0.

Fixes: 2b2142f2 ("spi: hisi-kunpeng: Add debugfs support")
Signed-off-by: oujiefeng <oujiefeng@huawei.com>
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/20211117012119.55558-1-f.fangjian@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

Since the DW_SPI_CAP_DWC_HSSI capability has just been replaced with using
the DW SSI IP-core versions interface, the DW SPI capability flags are now
represented with a gap. Let's fix it by redefining the DW_SPI_CAP_DFS32
macro to setting BIT(2) of the capabilities field.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211115181917.7521-8-Sergey.Semin@baikalelectronics.ruSigned-off-by: Mark Brown <broonie@kernel.org>

Since there is a common IP-core and component versions interface available
we can use it to differentiate the DW HSSI device features in the code.
Let's remove the corresponding DWC_HSSI capability flag then and use the
dw_spi_ip_is() macro instead.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211115181917.7521-7-Sergey.Semin@baikalelectronics.ruSigned-off-by: Mark Brown <broonie@kernel.org>

The driver currently supports two IP-core versions. It's DW APB SSI which
is older version of the controller with APB system bus interface, and DW
SSI controller with AHB bus interface. The later one is supposed to be a
new generation high-speed SSI. Even though both of these IP-cores have got
an almost identical registers space there are some differences. The driver
differentiates these distinctions by the DW_SPI_CAP_DWC_HSSI capability
flag. In addition to that each DW SSI IP-core is equipped with a Synopsys
Component version register, which encodes the IP-core release ID the has
been synthesized from. Seeing we are going to need the later one to
differentiate some controller peculiarities it would be better to have a
unified interface for both IP-core line and release versions instead of
using each of them separately.

Introduced here IP-core versioning interface consists of two parts:
1) IDs of the IP-core (virtual) and component versions.
2) a set of macro helpers to identify current IP-core and component
versions.

So the platform code is supposed to assign a proper IP-core version based
on it's platform -knowledge. The main driver initialization method reads
the IP-core release ID from the SSI component version register. That data
is used by the helpers to distinguish one IP-core release from another.
Thus the rest of the driver can use these macros to implement the
conditional code execution based on the specified IP-core and version IDs.

Collect the IP-core versions interface and the defined capabilities at the
top of the header file since they represent a common device description
data and so to immediately available for the driver hackers.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211115181917.7521-6-Sergey.Semin@baikalelectronics.ruSigned-off-by: Mark Brown <broonie@kernel.org>

The driver has been using the offset/bitwise-shift-based approach for the
CSR fields R/W operations since it was merged into the kernel. It can be
simplified by using the macros defined in the linux/bitfield.h and
linux/bit.h header files like BIT(), GENMASK(), FIELD_PREP(), FIELD_GET(),
etc where it is required, for instance in the cached cr0 preparation
method. Thus in order to have the FIELD_*()-macros utilized we just need
to convert the macros with the CSR-fields offsets to the masks with the
corresponding registers fields definition. That's where the GENMASK() and
BIT() macros come in handy. After that the masks can be used in the
FIELD_*()-macros where it's appropriate.

We also need to convert the macros with the CRS-bit flags using the manual
bitwise shift operations (x << y) to using the BIT() macro. Thus we'll
have a more coherent set of the CSR-related macros.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211115181917.7521-5-Sergey.Semin@baikalelectronics.ruSigned-off-by: Mark Brown <broonie@kernel.org>

Mostly due to a long driver history it's methods and macro names look a
bit messy. In particularly that concerns the code their prefixes. A
biggest part of the driver functions and macros have got the dw_spi/DW_SPI
prefixes. But there are some entities which have been just
"spi_/SPI_"-prefixed. Especially that concerns the CSR and their fields
macro definitions. It makes the code harder to comprehend since such
methods and macros can be easily confused with the global SPI-subsystem
exports. In this case the only possible way to more or less quickly
distinguish one naming space from another is either by context or by the
argument type, which most of the times isn't that easy anyway. In addition
to that a new DW SSI IP-core support has been added in the framework of
commit e539f435 ("spi: dw: Add support for DesignWare DWC_ssi"), which
introduced a new set or macro-prefixes to describe CTRLR0-specific fields
and worsen the situation. Finally there are methods with
no DW SPI driver-reference prefix at all, that make the code reading even
harder. So in order to ease the driver hacking let's bring the code naming
to a common base:
1) Each method is supposed to have "dw_spi_" prefix so to be easily
distinguished from the kernel API, e.g. SPI-subsystem methods and macros.
(Exception is the local implementation of the readl/writel methods since
being just the regspace accessors.)
2) Each generically used macro should have DW_SPI_-prefix thus being
easily comprehended as the local driver definition.
3) DW APB SSI and DW SSI specific macros should have prefixes as DW_PSSI_
and DW_HSSI_ respectively so referring to the system buses they support
(APB and AHB similarly to the DT clocks naming like pclk, hclk).
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211115181917.7521-4-Sergey.Semin@baikalelectronics.ruSigned-off-by: Mark Brown <broonie@kernel.org>

The dw_ssi_type enumeration describes the SPI frame formats the controller
supports, like Motorola SPI, Texas Instruments SSP and National
Semiconductors Microwire, that is the serial protocol utilized for the
SPI-transfers. Depending on the DW SSI IP-core configuration the protocol
could be either fixed or selectable. If it is changebale the protocol can
be selected by means of the CTRL0.FRF field, which possible values encoded
by the dw_ssi_type enumeration.  Aside with the denoted enum the field
values are also described by a set of SPI_FRF_{SPI,SSP,MICROWIRE} macros.
Thus currently the DW SPI driver has got two entities describing the same
data. Let's get rid of the enumeration one then, since first it hasn't
been used as enumeration-type but merely as a parametrized values set and
second that would unify the macro-based CSR read/write interface of the
driver. While at it convert the macro names to be more descriptive about
the protocols they represent.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211115181917.7521-3-Sergey.Semin@baikalelectronics.ruSigned-off-by: Mark Brown <broonie@kernel.org>

The exported from the DW SPI driver core/DMA symbols are only used by the
spi-dw-{mmio,pci,bt1}.o objects. Add these symbols to a separate
namespace then and make sure the depended modules have it imported.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211115181917.7521-2-Sergey.Semin@baikalelectronics.ruSigned-off-by: Mark Brown <broonie@kernel.org>

Netlogic XLP was removed in commit 95b8a5e0 ("MIPS: Remove NETLOGIC
support"). With those gone, the single platform left to support is
Cavium ThunderX2. Remove the Netlogic variant and DT support.

For simplicity, the existing kconfig name is retained.

Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211109161325.2203564-1-robh@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The requested DMA channels are never released. Do this in .remove as well
as in .probe. spi_register_controller() can return -EPROBE_DEFER if
cs-gpios are not probed yet.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211109103134.184216-1-alexander.stein@ew.tq-group.comSigned-off-by: Mark Brown <broonie@kernel.org>

Commit 6acaadc8 ("spi: clps711x: Driver refactor") removed the only use
of <linux/platform_data/spi-clps711x.h>, but left the header file behind.
This file is unused, delete it.

Cc: Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211102220203.940290-9-corbet@lwn.netSigned-off-by: Mark Brown <broonie@kernel.org>

Add Kconfig support for -Wimplicit-fallthrough for both GCC and Clang.

The compiler option is under configuration CC_IMPLICIT_FALLTHROUGH,
which is enabled by default.

Special thanks to Nathan Chancellor who fixed the Clang bug[1][2]. This
bugfix only appears in Clang 14.0.0, so older versions still contain
the bug and -Wimplicit-fallthrough won't be enabled for them, for now.

This concludes a long journey and now we are finally getting rid
of the unintentional fallthrough bug-class in the kernel, entirely. :)

Link: https://github.com/llvm/llvm-project/commit/9ed4a94d6451046a51ef393cd62f00710820a7e8 [1]
Link: https://bugs.llvm.org/show_bug.cgi?id=51094 [2]
Link: https://github.com/KSPP/linux/issues/115
Link: https://github.com/ClangBuiltLinux/linux/issues/236Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull xfs cleanups from Darrick Wong:
 "The most 'exciting' aspect of this branch is that the xfsprogs
  maintainer and I have worked through the last of the code
  discrepancies between kernel and userspace libxfs such that there are
  no code differences between the two except for #includes.

  IOWs, diff suffices to demonstrate that the userspace tools behave the
  same as the kernel, and kernel-only bits are clearly marked in the
  /kernel/ source code instead of just the userspace source.

  Summary:

   - Clean up open-coded swap() calls.

   - A little bit of #ifdef golf to complete the reunification of the
     kernel and userspace libxfs source code"

* tag 'xfs-5.16-merge-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: sync xfs_btree_split macros with userspace libxfs
  xfs: #ifdef out perag code for userspace
  xfs: use swap() to make dabtree code cleaner

Pull more parisc fixes from Helge Deller:
 "Fix a build error in stracktrace.c, fix resolving of addresses to
  function names in backtraces, fix single-stepping in assembly code and
  flush userspace pte's when using set_pte_at()"

* tag 'for-5.16/parisc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc/entry: fix trace test in syscall exit path
  parisc: Flush kernel data mapping in set_pte_at() when installing pte for user page
  parisc: Fix implicit declaration of function '__kernel_text_address'
  parisc: Fix backtrace to always include init funtion names

Pull arch/sh updates from Rich Felker.

* tag 'sh-for-5.16' of git://git.libc.org/linux-sh:
  sh: pgtable-3level: Fix cast to pointer from integer of different size
  sh: fix READ/WRITE redefinition warnings
  sh: define __BIG_ENDIAN for math-emu
  sh: math-emu: drop unused functions
  sh: fix kconfig unmet dependency warning for FRAME_POINTER
  sh: Cleanup about SPARSE_IRQ
  sh: kdump: add some attribute to function
  maple: fix wrong return value of maple_bus_init().
  sh: boot: avoid unneeded rebuilds under arch/sh/boot/compressed/
  sh: boot: add intermediate vmlinux.bin* to targets instead of extra-y
  sh: boards: Fix the cacography in irq.c
  sh: check return code of request_irq
  sh: fix trivial misannotations

Pull ARM fixes from Russell King:

 - Fix early_iounmap

 - Drop cc-option fallbacks for architecture selection

* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 9156/1: drop cc-option fallbacks for architecture selection
  ARM: 9155/1: fix early early_iounmap()

Pull devicetree fixes from Rob Herring:

 - Two fixes due to DT node name changes on Arm, Ltd. boards

 - Treewide rename of Ingenic CGU headers

 - Update ST email addresses

 - Remove Netlogic DT bindings

 - Dropping few more cases of redundant 'maxItems' in schemas

 - Convert toshiba,tc358767 bridge binding to schema

* tag 'devicetree-fixes-for-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  dt-bindings: watchdog: sunxi: fix error in schema
  bindings: media: venus: Drop redundant maxItems for power-domain-names
  dt-bindings: Remove Netlogic bindings
  clk: versatile: clk-icst: Ensure clock names are unique
  of: Support using 'mask' in making device bus id
  dt-bindings: treewide: Update @st.com email address to @foss.st.com
  dt-bindings: media: Update maintainers for st,stm32-hwspinlock.yaml
  dt-bindings: media: Update maintainers for st,stm32-cec.yaml
  dt-bindings: mfd: timers: Update maintainers for st,stm32-timers
  dt-bindings: timer: Update maintainers for st,stm32-timer
  dt-bindings: i2c: imx: hardware do not restrict clock-frequency to only 100 and 400 kHz
  dt-bindings: display: bridge: Convert toshiba,tc358767.txt to yaml
  dt-bindings: Rename Ingenic CGU headers to ingenic,*.h

Pull timer fix from Thomas Gleixner:
 "A single fix for POSIX CPU timers to address a problem where POSIX CPU
  timer delivery stops working for a new child task because
  copy_process() copies state information which is only valid for the
  parent task"

* tag 'timers-urgent-2021-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  posix-cpu-timers: Clear task::posix_cputimers_work in copy_process()

Pull irq fixes from Thomas Gleixner:
 "A set of fixes for the interrupt subsystem

  Core code:

   - A regression fix for the Open Firmware interrupt mapping code where
     a interrupt controller property in a node caused a map property in
     the same node to be ignored.

  Interrupt chip drivers:

   - Workaround a limitation in SiFive PLIC interrupt chip which
     silently ignores an EOI when the interrupt line is masked.

   - Provide the missing mask/unmask implementation for the CSKY MP
     interrupt controller.

  PCI/MSI:

   - Prevent a use after free when PCI/MSI interrupts are released by
     destroying the sysfs entries before freeing the memory which is
     accessed in the sysfs show() function.

   - Implement a mask quirk for the Nvidia ION AHCI chip which does not
     advertise masking capability despite implementing it. Even worse
     the chip comes out of reset with all MSI entries masked, which due
     to the missing masking capability never get unmasked.

   - Move the check which prevents accessing the MSI[X] masking for XEN
     back into the low level accessors. The recent consolidation missed
     that these accessors can be invoked from places which do not have
     that check which broke XEN. Move them back to he original place
     instead of sprinkling tons of these checks all over the code"

* tag 'irq-urgent-2021-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  of/irq: Don't ignore interrupt-controller when interrupt-map failed
  irqchip/sifive-plic: Fixup EOI failed when masked
  irqchip/csky-mpintc: Fixup mask/unmask implementation
  PCI/MSI: Destroy sysfs before freeing entries
  PCI: Add MSI masking quirk for Nvidia ION AHCI
  PCI/MSI: Deal with devices lying about their MSI mask capability
  PCI/MSI: Move non-mask check back into low level accessors

Pull x86 static call update from Thomas Gleixner:
 "A single fix for static calls to make the trampoline patching more
  robust by placing explicit signature bytes after the call trampoline
  to prevent patching random other jumps like the CFI jump table
  entries"

* tag 'locking-urgent-2021-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  static_call,x86: Robustify trampoline patching

Pull scheduler fixes from Borislav Petkov:

 - Avoid touching ~100 config files in order to be able to select the
   preemption model

 - clear cluster CPU masks too, on the CPU unplug path

 - prevent use-after-free in cfs

 - Prevent a race condition when updating CPU cache domains

 - Factor out common shared part of smp_prepare_cpus() into a common
   helper which can be called by both baremetal and Xen, in order to fix
   a booting of Xen PV guests

* tag 'sched_urgent_for_v5.16_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  preempt: Restore preemption model selection configs
  arch_topology: Fix missing clear cluster_cpumask in remove_cpu_topology()
  sched/fair: Prevent dead task groups from regaining cfs_rq's
  sched/core: Mitigate race cpus_share_cache()/update_top_cache_domain()
  x86/smp: Factor out parts of native_smp_prepare_cpus()

Pull perf fixes from Borislav Petkov:

 - Prevent unintentional page sharing by checking whether a page
   reference to a PMU samples page has been acquired properly before
   that

 - Make sure the LBR_SELECT MSR is saved/restored too

 - Reset the LBR_SELECT MSR when resetting the LBR PMU to clear any
   residual data left

* tag 'perf_urgent_for_v5.16_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Avoid put_page() when GUP fails
  perf/x86/vlbr: Add c->flags to vlbr event constraints
  perf/x86/lbr: Reset LBR_SELECT during vlbr reset