Debt forgiveness logic was counting the number of consecutive !busy periods
as the trigger condition. While this usually works, it can easily be thrown
off by temporary fluctuations especially on configurations w/ short periods.

This patch reimplements debt forgiveness so that:

* Use the average usage over the forgiveness period instead of counting
  consecutive periods.

* Debt is reduced at around the target rate (1/2 every 100ms) regardless of
  ioc period duration.

* Usage threshold is raised to 50%. Combined with the preceding changes and
  the switch to average usage, this makes debt forgivness a lot more
  effective at reducing the amount of unnecessary idleness.

* Constants are renamed with DFGV_ prefix.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Debt sets the initial delay duration which is decayed over time. The current
debt reduction halved the debt but didn't change the delay. It prevented
future debts from increasing delay but didn't do anything to lower the
existing delay, limiting the mechanism's ability to reduce unnecessary
idling.

Reset iocg->delay to 0 after debt reduction so that iocg_kick_waitq()
recalculates new delay value based on the reduced debt amount.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Debt reduction was blocked if any iocg was short on budget in the past
period to avoid reducing debts while some iocgs are saturated. However, this
ends up unnecessarily blocking debt reduction due to temporary local
imbalances when the device is generally being underutilized, while also
failing to block when the underlying device is overwhelmed and the usage
becomes low from high latency.

Given that debt accumulation mostly happens with swapout bursts which can
significantly deteriorate the underlying device's latency response, the
current logic is not great.

Let's replace it with ioc->busy_level based condition so that we block debt
reduction when the underlying device is being saturated. ioc_forgive_debts()
call is moved after busy_level determination.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Debt reduction logic is going to be improved and expanded. Factor it out
into ioc_forgive_debts() and generalize the comment a bit. No functional
change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Add DM target feature flag DM_TARGET_NOWAIT which advertises that
target works with REQ_NOWAIT bios.

Add dm_table_supports_nowait() and update dm_table_set_restrictions()
to set/clear QUEUE_FLAG_NOWAIT accordingly.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Add QUEUE_FLAG_NOWAIT to allow a block device to advertise support for
REQ_NOWAIT. Bio-based devices may set QUEUE_FLAG_NOWAIT where
applicable.

Update QUEUE_FLAG_MQ_DEFAULT to include QUEUE_FLAG_NOWAIT.  Also
update submit_bio_checks() to verify it is set for REQ_NOWAIT bios.
Reported-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

No need to go through the hd_struct to find the partition number.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

No need to go through the hd_struct to find the partition number.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

bd_contains is never NULL for an open block device.  In addition ibd_bd
is always set to a block device that was exclusively opened by the
target code, so the holder is guranteed to be ib_dev as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

The ->bd_contains field is set by __blkdev_get and drivers have no
business manipulating it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

bd_disk is set on all block devices, including those for partitions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

bd_disk is set on all block devices, including those for partitions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Song Liu <song@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

To check for partitions of the same disk bd_contains works as well, but
bd_disk is way more obvious.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Song Liu <song@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Add a littler helper to make the somewhat arcane bd_contains checks a
little more obvious.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

bd_contains is an implementation detail and should not be mentioned in
a userspace API documentation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Replace the two negative flags that are always used together with a
single positive flag that indicates the writeback capability instead
of two related non-capabilities.  Also remove the pointless wrappers
to just check the flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Replace BDI_CAP_NO_ACCT_WB with a positive BDI_CAP_WRITEBACK_ACCT to
make the checks more obvious.  Also remove the pointless
bdi_cap_account_writeback wrapper that just obsfucates the check.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

The BDI_CAP_STABLE_WRITES is one of the few bits of information in the
backing_dev_info shared between the block drivers and the writeback code.
To help untangling the dependency replace it with a queue flag and a
superblock flag derived from it.  This also helps with the case of e.g.
a file system requiring stable writes due to its own checksumming, but
not forcing it on other users of the block device like the swap code.

One downside is that we an't support the stable_pages_required bdi
attribute in sysfs anymore.  It is replaced with a queue attribute which
also is writable for easier testing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

There is no point in trying to call bdev_read_page if SWP_SYNCHRONOUS_IO
is not set, as the device won't support it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

BDI_CAP_SYNCHRONOUS_IO is only checked in the swap code, and used to
decided if ->rw_page can be used on a block device.  Just check up for
the method instead.  The only complication is that zram needs a second
set of block_device_operations as it can switch between modes that
actually support ->rw_page and those who don't.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Just checking SB_I_CGROUPWB for cgroup writeback support is enough.
Either the file system allocates its own bdi (e.g. btrfs), in which case
it is known to support cgroup writeback, or the bdi comes from the block
layer, which always supports cgroup writeback.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Drivers shouldn't really mess with the readahead size, as that is a VM
concept.  Instead set it based on the optimal I/O size by lifting the
algorithm from the md driver when registering the disk.  Also set
bdi->io_pages there as well by applying the same scheme based on
max_sectors.  To ensure the limits work well for stacking drivers a
new helper is added to update the readahead limits from the block
limits, which is also called from disk_stack_limits.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

The raid5 and raid10 drivers currently update the read-ahead size,
but not the optimal I/O size on reshape.  To prepare for deriving the
read-ahead size from the optimal I/O size make sure it is updated
as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Song Liu <song@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Set up a readahead size by default, as very few users have a good
reason to change it.  This means code, ecryptfs, and orangefs now
set up the values while they were previously missing it, while ubifs,
mtd and vboxsf manually set it to 0 to avoid readahead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: David Sterba <dsterba@suse.com> [btrfs]
Acked-by: Richard Weinberger <richard@nod.at> [ubifs, mtd]
Signed-off-by: Jens Axboe <axboe@kernel.dk>

aoe forces a larger readahead size, but any reason to do larger I/O
is not limited to readahead.  Also set the optimal I/O size, and
remove the local constants in favor of just using SZ_2G.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Inherit the optimal I/O size setting just like the readahead window,
as any reason to do larger I/O does not apply to just readahead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Ever since the switch to blk-mq, a lower device not used for VM
writeback will not be marked congested, so the check will never
trigger.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

The last user of SB_I_MULTIROOT is disappeared with commit f2aedb71
("NFS: Add fs_context support.")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

There are no users outside the core block code left now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Use blkdev_get_by_dev instead of bdget + blkdev_get.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

swap_type_of is used for two entirely different purposes:

 (1) check what swap type a given device/offset corresponds to
 (2) find the first available swap device that can be written to

Mixing both in a single function creates an unreadable mess.  Create two
separate functions instead, and switch both to pass a dev_t instead of
a struct block_device to further simplify the code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Just check the dev_t to help simplifying the code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Use blkdev_get_by_dev instead of bdgrab + blkdev_get.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Use blkdev_get_by_dev instead of igrab (aka open coded bdgrab) +
blkdev_get.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Use blkdev_get_by_dev instead of bdget_disk + blkdev_get.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Turn binding into a normal dev_t as the struct block device doesn't
buy us anything and use blkdev_open_by_dev to actually open it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Use blkdev_get_by_dev instead of bdgrab + blkdev_get.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Replace bdget + blkdev_get by blkdev_get_by_dev.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Remove code which has been dead since the initial commit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Use blkdev_get_by_dev instead of bdgrab + blkdev_get.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>